2023 Ram 2500 TSBs

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Rain Sensor Internal Failure.

Rain Sensor Internal Failure.

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

(MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin involves reprogramming the TBM with the latest available software.Telematics Box Module (TBM) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin involves reprogramming the TBM with the latest available software.

a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.Telematics Box Module (TBM) Firmware Over The Air (FOTA) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.Telematics Box Module (TBM) Firmware Over The Air (FOTA) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

This bulletin involves flashing the TBM to the latest software level in the case that the FOTA did not function.

Sensor(s) Not Reading And Or Showing Dashes.

This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.

experience one or more of the following: - Error display of ""Uconnect Box Requires Service/Wifi Unavailable"" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of ""Uconnect Box Requires Service"" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ]."

U11C1-00 (Reductant Control Module Received Implausible Data From ECM/PCM), do not replace the DEF Pump. Follow TSB's released and appropriate Service Diagnostics.

Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only."

/ DP vehicles with 6.7L (ETL / ETM / ETN) built on or before October 15,2024 and exhibiting DTCs P21C4-00 (Reductant Line Heater Relay Control Circuit High) and / or U11C1-00 (Reductant Control Module received implausible Data from ECM / PCM). These DTCs will occur after installation of service DCU 68458603AB. Do not replace parts until after the TSB 25-008-24 is performed. If the DTC(s) continue to set, then follow the Service Diagnostics for the applicable DTC."

Line Heater Control Circuit High, and U11C1 Reductant Control Module Received Implausible Data From ECM/PCM, Set

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): C2202-00 - Original VIN Mismatch/missing. Customers may also experience: ""Service air suspension"" icon light may be on and system may be defaulting to normal ride heigh This bulletin involves updating the ASCM with the latest available software."

what DTC are detected and take proper steps acceding to the DTC's. 2.- Make sure all the switches are properly connected to their harness, disconnect the switch and reconnect it. 3.- Review the window Switch for any physical issue (Button stuck, broken) If after performing these steps the switch remains faulty. Follow suggested repairs per diagnostics performed.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

steering controls inop, TCS light DTC C0051 or horn blowing while turning, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. 7.- Before replacing the SCCM disconnect it and reconnect it again. If there are no DTC's active, physical defects, steering controls inop, wipers inop, nor turn signal inop, horn inop, then SCCM does not need to be replaced.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Stuck, U103C-00 KIN/IGNM Communication

Switch for any physical issue (Button stuck, broke). If no physical issue identified, move to next steps. 2.- Make sure the switch harness is properly connected, disconnect the switch and reconnect it, and reverify the issue. 3.- Check for what DTC are detected and take proper steps. If there are no DTC's nor physical defectives, then the telescopic mirror switches can't be replaced.

Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P21C4-00 - Reductant Line Heater Relay Control Circuit High. U11C1-00 - Reductant Control Module Received Implausible Data From ECM/PCM. These DTCs will occur after installation of service DCU 68458603AB. This bulletin involves reprogramming the DCU with the latest available software."

Displayed on Cluster

installing the Mopar service battery as a replacement for the factory battery, there is an interference issue with the right busbar cover on the positive terminal side of the battery. This bulletin involves modifying the right busbar cover on the positive terminal side of the battery. "

Maps not loading on the Instrument Panel Cluster (IPC) display. Cannot change satellite stations, display shows one station on screen but is playing another. Battery drain. A Black screen after clicking accept at start up (Rearview camera functions normally). Radio resets (Rearview camera functions normally). Wireless connectivity disconnecting. CarPlay icon does not appear in device manager. Audio disruptions. SXMT inoperative. Audio mute. Passenger screen blank. Passenger screen apps missing. Missing profiles icon. IPC displays incorrect audio source. Radio is slow to respond. Trailer tire pressure configurations deleted. Steering wheel controls skipping SXMT channels. Recent calls not displayed. Phone audio playing when ignition is off. In addition, the following software enhancement(s) are available: Icon size/layout improvements. Carplay/Android Auto improvements. Uconnect Phone improvements. FOTA improvements. Passenger screen camera app improvements. Voice Recognition (VR) command improvements. This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from T25.48 or T25.51 to T27.46."

sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.

This bulletin involves reprogramming the MSM with the latest available software."

One Or More Exhaust Temperature Sensor (EGT) Diagnostic Trouble Codes (DTCs), Set.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

following: ? **Blank screen (Rear view camera is not affected and will still function normally).** ? Battery drain. ? Radio resets (Rear view camera will still function normally). ? Wireless connectivity device disconnect. ? CarPlayT icon does not appear in device manager. ? Climate icon missing. ? Audio disruptions. ? SXMT inoperative. ? Audio muted. ? Passenger screen blank. ? Passenger screen apps missing. ? Missing profiles icon. ? Instrument Panel Cluster (IPC) displays incorrect audio source. ? Radio is slow to respond. ? Trailer tire pressure configurations deleted. ? Steering wheel controls skipping SXMT channels. ? Recent calls not displayed. ? Phone audio playing with ignition off. The following improvements are also included with this update: ? Apple CarPlayT and Android AutoT improvements. ? Voice Recognition (VR) command improvements. ? Uconnect phone improvements. ? FOTA improvements. ? Passenger screen camera app improvements. ? Icon size/layout improvements. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S24.13 or S24.18 to S26.17. NOTE: The national launch for the FOTA is expected to begin November 25, 2022.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

following: ? Uconnect Box Message at startup. ? Uconnect Box Error or Requires Service Message. ? Connectivity: Diagnostic Trouble Codes (DTCs) for Electronic Control Modules (ECUs) won?t be shown to customer through the Vehicle Health alert (Mobile app or email). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from **5.13 and** 5.25 to 5.39.1.

This feature is ON by default. This bulletin involves reprogramming the BCM module with the latest available software.

following: ? Uconnect Box Message at Startup. ? Uconnect Box Error Or Requires Service Message. ? Uconnect Mobile App trunk status showing as closed when trunk is open. ? Diagnostic Trouble Codes (DTCs) for Electronic Control Modules (ECUs) won?t be shown to customer through the Vehicle Health alert (Mobile App or email). The TBM software will be updated from 5.25 to 5.39.1.

This bulletin involves reprogramming the PCM with the latest available software.

following: ? Uconnect Box Message at Startup. ? Uconnect Box Error Or Requires Service Message. ? Connectivity: Uconnect Mobile App trunk status showing as closed when trunk is open. ? Connectivity: Diagnostic Trouble Codes (DTCs) for Electronic Control Modules (ECUs) won?t be shown to customer through the Vehicle Health alert (Mobile app or email). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.25 to 5.39.1. NOTE: The national launch for the FOTA is expected to begin June 26, 2023.

Redacted Content for further assistance. If no response in 15 minutes, proceed with repair.

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

Check for electrical harness routing too close to speaker's rear moving parts, improper connection, and/or harness pinch or damage. 2. Ensure no loose components, including trim grilles, fasteners, surrounding IP parts, etc. were found when removing the speaker. 3. Try "bad" speaker at another IP location and see if noise follows speaker. Try a different "good" speaker at "bad speaker location" and see if noise still happens at "bad" location. If even with this verification and adjustments the speaker sounds bad, test the individual speaker with the audio files provided in the Service Library Homepage under "Reference Materials" prior to replacement

following: ? **Blank screen (Rear view camera is not affected and will still function normally).** ? Battery drain. ? Radio resets (Rear view camera will still function normally). ? Wireless connectivity device disconnect. ? CarPlayT icon does not appear in device manager. ? Climate icon missing. ? Audio disruptions. ? SXMT inoperative. ? Audio muted. ? Passenger screen blank. ? Passenger screen apps missing. ? Missing profiles icon. ? Instrument Panel Cluster (IPC) displays incorrect audio source. ? Radio is slow to respond. ? Trailer tire pressure configurations deleted. ? Steering wheel controls skipping SXMT channels. ? Recent calls not displayed. ? Phone audio playing with ignition off. The following improvements are also included with this update: ? Apple CarPlayT and Android AutoT improvements. ? Voice Recognition (VR) command improvements. ? Uconnect phone improvements. ? FOTA improvements. ? Passenger screen camera app improvements. ? Icon size/layout improvements. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S24.13 or S24.18 to S26.17. NOTE: The national launch for the FOTA is expected to begin November 25, 2022.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S26.15 to S26.17. NOTE: National launch for this FOTA update is expected to begin February 09, 2023.

NOx Sensor Diagnostic Trouble Codes (DTCs) Diagnosis Information.

damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P0299-00 - Turbocharger Underboost. Customers may also comment on the following: Low power/acceleration or lag condition. This bulletin involves performing an Air Handling Performance Test (APT) and possibly replacing the air filter.

New Part: 68645327AA (Non-Oiled Air Filter) Replaces: 53034051AA (Oiled Air Filter) - This part is superseded and should no longer be installed. The air filter for all other applications remains unchanged: Continue to use 68517554AA for: All 2018 MY and older 6.7L Cummins equipped vehicles. All 2019 MY and newer vehicles with non-6.7L engines. 2. Special Service Procedure for DTC P0299 Application: 2019-2024 MY HD Trucks with 6.7L Diesel (ETM/ETN) Condition: If DTC P0299 is active and the vehicle is equipped with the previous oiled air filter (PN# 53034051AA). Procedure: Replace the oiled air filter (53034051AA) with the new non-oiled filter (68645327AA). Service Catalog reflects these updated usages.

Clicking noise. Engine noise.

illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0234-00 - Turbocharger Overboost Condition. P0299-00 - Turbocharger Underboost. P0101-00 - Mass Air Flow Sensor "A" Circuit Performance. P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. P2262-00 - Turbocharger Boost Pressure Not Detected - Mechanical. P0471-00 - Exhaust Pressure Sensor 1 Performance. P1451-00 - Diesel Particulate Filter System Performance. P2457-00 - Exhaust Gas Recirculation Cooling System Performance. P2263-00 - Turbo Boost System Performance. P2459-00 - Diesel Particulate Filter Regeneration Too Frequent. P24A2-00 - Diesel Particulate Filter Regeneration Incomplete - Bank 1. P0401-00 - EGR System Performance. P0402-00 - EGR Flow Excessive Detected

In these situations, it is recommended to use the appropriate Mopar air filter (57008652AA). The "AC" level of the part is in development to resolve this issue. 1BP00507AB should still be usable for 2018 and older Model year Cummins engines.

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P245D-00 - EGR Cooler Bypass Control Circuit High. P02E3-00 - Diesel Intake Air Flow Control Circuit High. P0490-00 - EGR Control Circuit High. P229F-00 - Aftertreatment NOX Sensor Circuit Performance - Bank 1 Sensor 2. P0299-00 - Turbocharger Underboost. P242F-00 - Diesel Particulate Filter Restriction - Ash Accumulation. P0128-00 - Thermostat Rationality. P0234-00 - Turbocharger Overboost Condition.** Customers may also comment on one or more of the following: **Engine speed unstable when vehicle is stationary, not in gear and running on high speed governor (max engine speed).** Longer crank time than normal. Transmission overheat conditions with a message displayed in the Instrument Panel Cluster (IPC) stating "Transmission oil temperature is too hot" This bulletin involves reprogramming the Engine Control Module (ECM/PCM) with the latest available software.

please reference SOL Case #S2508000062 prior to replacement of Transfer Case shift motor.

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0868-00 - Transmission Fluid Pressure Low. P0933-00 - Hydraulic Pressure Sensor Range/performance P0735-00 - Gear 5 Shift Incorrect Ratio. P0729-00 - Gear 6 Shift Incorrect Ratio. Customers may also experience one or more of the following: While driving the vehicle, the Instrument Panel Cluster (IPC) is showing a transmission overheat message. Check engine light illuminates and will turn on and off while driving. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.

(D2/DD/DF/DJ/DP)

08-159-25 before replacing any parts on the seat back frame.

SYMPTOM/CONDITION: Fore-aft function does NOT work when actuating the seat switch. DIAGNOSIS: 1) Put seat in position for inspection. 2) Disconnect seat wire harness motor connector from the fore-aft motor on the seat adjuster, wait 10 seconds, and reconnect. 3) Verify function of the fore/aft adjuster. Step 1. Open 2nd row door and function rear seat cushions up to stowed position. Step 2. Adjust the driver front seat to the full up position. Use switches on the side shield to move power seat fully up. Step 3. Remove the 4 bolts that hold the seat to the truck floor and discard. The bolts have lock patch that is not reusable. Step 4. Lay the seat down so its laying on its back so the underside of the seat is easily accessible. Step 5. Remove the fore/aft wire harness motor connector from the fore/aft motor (back right of the seat adjuster). Push on the tab to remove the motor wire harness connector from the motor. Leave disconnected for 10 seconds. Step 6. Reconnect the fore/aft wire harness motor connector to the fore/aft motor. Push / Pull / Push the connector with fingers to ensure the wire harness connector is fully seated to the fore/aft motor connector. Step 7. Before assembling the seat back to the truck floor, cycle the seat to check that the motor is working properly by pressing the fore/aft switch. If fore/aft motor does not function, please refer to Replacement Procedure below. Step 8. If the seat is working properly, carefully reassemble the seat back to the truck floor using the four new bolts. Use a torque wrench to verify 47 Nm. Step 9. *Note: Checking the passenger seat will be the same procedure as the driver seat. REPLACEMENT PROCEDURE  Only for seats rejected after inspection. Replace Power Seat Adjuster per MOPAR service part replacement instructions. MOPAR Part Numbers: 68455847AA, 68455848AA, 68455849AA"

This bulletin involves adding oil system protection and letting the engine idle."

REPAIR SUMMARY: This bulletin involves adding oil system protection and letting the engine idle."

Or Corrupted

(MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P2459 - Diesel Particulate Filter Regeneration Too Frequent. Customers may also experience the following: Vehicle has entered engine performance de-rate mode. NOTE: Engine performance de-rate mode will occur when DTC P2459 has been set for a long period. This bulletin involves replacing the DPF if DTC P2459 is set."

(MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P2459 - Diesel Particulate Filter Regeneration Too Frequent. Customers may also experience the following: Vehicle has entered engine performance de-rate mode. NOTE: Engine performance de-rate mode will occur when DTC P2459 has been set for a long period. This bulletin involves replacing the DPF if DTC P2459 is set."

(MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P2459 - Diesel Particulate Filter Regeneration Too Frequent. Customers may also experience the following: Vehicle has entered engine performance de-rate mode. NOTE: Engine performance de-rate mode will occur when the DTC has been set for a long period. This bulletin involves replaceing the DPF if DTC P2459 is set."

Wiper Doesnt Work or Stops Randomly On Glass

Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."

? Engine Stop Start (ESS) is inoperable.

Please verify the radio is at the latest available software level. If active DTCs are set, perform the appropriate diagnostic procedure in service information. If the condition is intermittent, refer to Section 29 Non-DTC Based Diagnostics and perform the diagnostic procedure related to the customer's complaint. If concern is still present or the customer has returned to the dealer multiple times for the same complaint, contact engineering FCA Redacted Content. If no answer or call back within 15 minutes, continue with regular diagnosis.

Diagnostic Trouble Code (DTC) P2580 ? Turbocharger Speed Sensor Circuit Low, Set.

Pickup (DJ), 2022 and 2023 Ram 3500 Pickup (D2), 2022 and 2023 Ram 3500 Cab Chassis (DD) and 2022 and 2023 4500/5500 Ram Cab Chassis (DP) (Rev. B)

2024 Ram 2500 Pickup (DJ), 2022 - 2024 Ram 3500 Pickup (D2), 2022 - 2024 Ram 3500 Cab Chassis (DD) and 2022 - 2024 4500/5500 Ram Cab Chassis (DP) (Rev. C)

Pickup (DJ), 2022 - 2024 Ram 3500 Pickup (D2), 2022 - 2024 Ram 3500 Cab Chassis (DD) and 2022 - 2024 4500/5500 Ram Cab Chassis (DP) (Rev. C)

? Transmission overheat conditions with a message displayed in cluster stating "Transmission oil temperature is too hot". This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software.

Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0642 - Sensor Reference Voltage 1 Circuit Low. ? P0652 - Sensor Reference Voltage 2 Low. ? P06D3 - Sensor Reference Voltage 5 Circuit Low. ? P0102 - Mass Air Flow Sensor A Circuit Low. ? P0750 - Shift Solenoid 1 Control Circuit - Open. ? P0755 - Shift Solenoid 2 Control Circuit - Open. ? P0706 - Transmission Range Sensor Rationality. ? P0765 - Shift Solenoid D. ? P0770 - Shift Solenoid E. ? P2761 - Torque Converter Clutch Pressure Control Solenoid Control Circuit-Open. In addition, the customer may experience the following: ? An engine no crank/start. This bulletin involves performing an extended idle test and possibly replacing the ECM.

Pickup (DJ), 2022 and 2023 Ram 3500 Pickup (D2), 2022 and 2023 Ram 3500 Cab Chassis (DD) and 2022 and 2023 4500/5500 Ram Cab Chassis (DP) (Rev. B)

J)

Pickup (DJ), 2022 and 2023 Ram 3500 Pickup (D2), 2022 and 2023 Ram 3500 Cab Chassis (DD) and 2022 and 2023 4500/5500 Ram Cab Chassis (DP) (Rev. A)

J)

Pickup (DJ), 2022 and 2023 Ram 3500 Pickup (D2), 2022 and 2023 Ram 3500 Cab Chassis (DD) and 2022 and 2023 4500/5500 Ram Cab Chassis (DP) (Rev. A) (document published on 8/5/22 with incorrect date on communication of 8/4/22)

J)

Pickup (DJ), 2022 and 2023 Ram 3500 Pickup (D2), 2022 and 2023 Ram 3500 Cab Chassis (DD) and 2022 and 2023 4500/5500 Ram Cab Chassis (DP) (Rev. A) (document published on 8/5/22 with incorrect date on communication of 8/4/22)

or B1570-93

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

Record or document software version prior to troubleshooting, as soon as any infotainment issue has been found or reported. Also always document in claim. Steps to capture Radio version number: 1. Go to "Vehicle" 2. Go to "Settings" 3. Go to "System Information" 4. Find the radio version from "Version information" Example software version: U37.2, U39.4, etc.

Verify Z part number availability. Order a Z part number for all Exchange Orders: Mopar, customer pay and service contract."

Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process

continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.

noise coming from front/rear speakers. Heard when radio is on and no media is playing, or volume high/low with media playing. This bulletin involves performing a routine in the radio to reduce unwanted speaker noise.

noise coming from front/rear speakers. Heard when radio is on and no media is playing, or volume high/low with media playing. This bulletin involves performing a routine in the radio to reduce unwanted speaker noise.

of the following: ? Ambient Light Setting inoperable. ? Radio reset (Rearview camera functions normally). ? Voice Recognition (VR) inoperable. ? Audio sources inoperable. ? Wireless CarPlayT inoperable. ? Setting preferences not saved on correct profile. ? Audio loss. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S24.6, S26.15 and T25.43 to T25.48. NOTE: The National campaign for this FOTA update is estimated to be launched on September 29, 2023.

(New and Exchange) ?2023 Jeep Grand Cherokee (WL), 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT), 2023 Ram Heavy Duty Pickup (DD/DF/DJ/ DP/D2), 2024 Jeep Wrangler (JL) and 2024 Jeep Gladiator (JT) (Rev. B)

?2023 Jeep Grand Cherokee (WL), 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT), 2023 Ram Heavy Duty Pickup (DD/DF/DJ/DP/D2), 2024 Jeep Wrangler (JL) and 2024 Jeep Gladiator (JT) (Rev. F)

vehicle after deep sleep, wrong splash screen appears. This bulletin involves reprogramming the IPC with the latest available software.

Exchange) ?2021 - 2023 Jeep Grand Cherokee (WL), 2022 - 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT) and 2023 Ram Heavy Duty Pickup (DD/DF/DJ/ DP/D2) (Rev. E)

Driver and/or passenger seat inoperative. This bulletin involves replacing the front power seat adjusters."

Adding Remote Start

This bulletin involves replacing the front driveshaft."

Adding Remote Start

Programmed

RAM Built Trucks Only)

Models (Mexico RAM Built Trucks Only)

this is normal and not a defect.

This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2023 to 2013 HD Trucks. The following information is intended to eliminate confusion.

Additional Diagnostics.

This bulletin involves replacing the front driveshaft.

C0604- Active Air Dam Control Performance

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

chatter/streak/jump/skip/smear or make noise while traveling across the windshield.

Output Shaft Seal should be considered in lieu of entire transfer case or driveshaft replacement. In the case of major damage to components, contact StarCenter and/or proceed with replacements as necessary.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Output Shaft Seal - service part numbers 68161329AA OR 68449218AA (max tow application) - should be considered in lieu of entire transfer case or driveshaft replacement. In the case of major damage to components, contact StarCenter and/or proceed with replacements as necessary

Inspect for visible bubbling/delamination on the instrument panel base panel. If bubbling/delamination is present, replace the base panel.

to verify the values are within specification stated in the service procedures. 2- Swap the switch with the issue with the other side. This switch is used in both rear doors. If after the swap the issue is now present at the other door and the original door position no longer has the issue, replace the switch.

Mirror Contacts Door Window Glass In The Folded Position.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

TPM Lamp On.

This bulletin involves replacing the inverter switch.

due to inconsistent operator installation effort, leading to latent BSR issue that manifests under customer usage conditions. Solution: remove and reinstall light guide to be fully seated in the bracket retainer.

Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.

TPM Lamp On.

ABS And/Or Traction Control Lights May Also Be On

Discussion: Some customers may experience a, inop rear axle locker, and Service Axle Locker message. After further investigation, the technician may not find any diagnostic trouble codes (DTCs) set. However, intermittently, they may find the following DTCs set in the Drivetrain Control Module (DTCM). C141C-11 Rear Differential Control Circuit Short To Ground. C141C-13 Rear Differential Control Circuit Open. If the technician is working on a vehicle with the above condition, please perform the repair procedure below. Repair Procedure: 1. Remove the rear differential cover. 2. Inspect the e-locker actuator wiring harness for damage due to contact with the differential.

11 active codes, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure the switch is properly connected and there is no corrosion or pinching, disconnect the switch & reconnect it, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between gear selector switch and BCM. For example, try switching between driving modes. 4.- Read at the BCM diagnosis session if BCM is receiving information from gear selector. 5.- Do a hard reset to BCM and evaluate if any DTC or failure code is set. Retest if failure still present. If there are no DTC's, physical defects, gear selector inop, then the Electronic Gear Selector Switch does not need to be replaced.

Transmission" message in the Instrument Cluster panel (IPC). ? Erratic shift bump felt/heard. ? Transmission stuck in seventh gear. ? Inability to accelerate. ? Not enough power to tow. This bulletin involves reprogramming the TCM with the latest available software.

Diagnostic Trouble Codes (DTCs) P0944 ? Loss of Hydraulic Pump Prime, and P0868 ? Transmission Fluid Pressure Low, Set.

internal transmission components. Refer to SOL Publication S2321000007.

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris "

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debri "

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris "

Diesel Exhaust Fluid (DEF) System Diagnostic Trouble Codes (DTCs) due to Hydrocarbon Contamination.

NOTE: This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axle fluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components. NOTE: This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every 3 years or 30,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual. This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration."

Verify Z part number availability. Order a Z part number for all Exchange Orders, Mopar, customer pay and service contract.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

Some technicians have been using the brake pedal pad labor code which is not the same as the parking brake pedal pad. The correct labor operation code should be for parking brake pedal pad replacement is 05-05-06-01.

brake Switch for any physical issue (Button stuck, broke). If no physical issue identified, move to next steps. 2.- Make sure the switch harness is properly connected, disconnect the switch and reconnect it, and reverify the issue. 3.- Check for what DTC are detected and take proper steps. 4.- Review the internal resistance of the switch to corroborate if it is shorted: a) Between Pins 10&2 it should be around 13ohms +/- 4ohms b) Between Pins 3 & 4 and 4 & 6, 160 ohms +/-10 Ohms If a problem is found in the resistor values. Please replace the Switch.

In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.

call FCA REDACTED CONTENT for a FasTrack part return. ~ If no response in 15 minutes, proceed with repair. Please leave the last 8 of VIN, plus vehicle mileage, and dealer code.

Due to brake vacuum pumps returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.

Balance/Fade does not stay on when setup by one press. Wireless Phone interface freezes after User accepts incoming call when in a conference call. System switches to Wireless after key cycle, profile change, theme change, or theme mode change. After overnight sleep cycle defrost vent and dash vent are cut off due to duplicate front defrost. Surround sound image loads incorrectly when activating with Android Auto?. Radio plays different SXM station than user selected. After a software update, previously added widgets to Shortcuts show up as "Couldn't add widget". SXM presets grayed out, non-functional and audio intermittently fades in and out. Switch between the Cargo Camera screen and the AUX camera screen while switching between Night/Day modes, camera image may not be displayed. (Rearview camera functions normally). Deleting songs from Artist & Song Notifications, then Sports announcement displayed and "X" to cancel freezes screen. (Rearview camera functions normally). After a long sleep cycle, the left menu bar showing SXM station categories (i.e. For You, Music, Sports, News, Presets) does not display all categories. When playing SXM, after switching to a profile with a different Theme Mode, starting Bus Sleep cycle causes Presets Shown to change from 20 to 15. (Rearview camera functions normally). When call received from another vehicle, the voice of the receiving end is echoed back, the caller's vehicle has no echo issue. No response from Browse hard button when SXM source is selected. Screen graphics/Theme - Shortcut widgets show up as "Loading", even after full sleep cycle. Android Auto? - Call duration displayed on status bar notification area is different than the actual duration. Widget view and Android Auto? screen are showing correct. Back Camera Icon is grayed out and it's not accessible f

Balance/Fade does not stay on when setup by one press. Wireless Phone interface freezes after User accepts incoming call when in a conference call. System switches to Wireless after key cycle, profile change, theme change, or theme mode change. After overnight sleep cycle defrost vent and dash vent are cut off due to duplicate front defrost. Surround sound image loads incorrectly when activating with Android Auto?. Radio plays different SXM? station than user selected. After a software update, previously added widgets to Shortcuts show up as "Couldnt add widget". SXM? presets greyed out, non-functional and audio intermittently fades in and out. Switch between the Cargo Camera screen and the AUX camera screen while switching between Night/Day modes, camera image may not be displayed (Rearview camera functions normally). Deleting songs from Artist & Song Notifications, then Sports announcement displayed and 9X9 to cancel freezes screen (Rearview camera functions normally). After a long sleep cycle, the left menu bar showing SXM? station categories (i.e. For You, Music, Sports, News, Presets) does not display all categories. When playing SXM?, after switching to a profile with a different Theme Mode, starting Bus Sleep cycle causes Presets Shown to change from 20 to 15 (Rearview camera functions normally). When call received from another vehicle, the voice of the receiving end is echoed back, the callers vehicle has no echo issue. No response from Browse hard key when SXM? source is selected. Screen graphics/Theme - Shortcut widgets show up as "Loading", even after full sleep cycle. Android Auto? - Call duration displayed on status bar notification area is different than the actual duration. Widget view and Android Auto? screen are showing correct. Back Camera Icon is grayed out and its not accessible from

heard when Assist & SOS Call is established. ? Balance/Fade does not stay on when setup by one press. ? Wireless Phone interface freezes after User accepts incoming call when in a conference call. ? System switches to Wireless after key cycle, profile change, theme change, or theme mode change. ? After overnight sleep cycle defrost vent and dash vent are cut off due to duplicate front defrost. ? Surround sound image loads incorrectly when activating with Android Auto?. ? Radio plays different SXMT station than user selected. ? After a software update, previously added widgets to Shortcuts show up as "Couldn?t add widget". ? SXMT presets greyed out, non-functional and audio intermittently fades in and out. ? Switch between the Cargo Camera screen and the AUX camera screen while switching between Night/Day modes, camera image may not be displayed. (Rearview camera functions normally). ? Deleting songs from Artist & Song Notifications, then Sports announcement displayed and "X" to cancel freezes screen. (Rearview camera functions normally). ? After a long sleep cycle, the left menu bar showing SXMT station categories (i.e. For You, Music, Sports, News, Presets) does not display all categories. ? When playing SXMT, after switching to a profile with a different Theme Mode, starting Bus Sleep cycle causes Presets Shown to change from 20 to 15. (Rearview camera functions normally). ? When call received from another vehicle, the voice of the receiving end is echoed back, the caller?s vehicle has no echo issue. ? No response from Browse hard key when SXMT source is selected. ? Screen graphics/Theme -Shortcut widgets show up as "Loading", even after full sleep cycle. ? Android Auto? - Call duration displayed on status bar notification area is different than the actual duration. Widget view and Android Auto? screen are s

Announces the addition of the Rear AxleAssembly replacementfor 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT)vehicles to the Powertrain Pre-Authorization program to ensure proper repair of Rear AxleAssembly failures and to assist in quality improvements. REV.A

Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program for all dealers (Base, Plus & Premium) to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A

B)

This bulletin involves performing a proxi/proxy alignment.

This bulletin involves performing a proxi/proxy alignment.

prior to replacing seatbelt please inspect for debris and any build up on the webbing and DRing. If evidence of debris and build up, please clean seatbelt webbing or turning loop as described below. Seat Belt Maintenance: Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. Dry with a soft cloth. Sun damage can also weaken the fabric. Replace the belts if they appear frayed or worn or if the buckles do not work properly. NOTE: If the belts retract slowly, inspect the upper turning loop for soiling. If soiling is present, clean with a wet soft cloth until all residue is removed.

following: ? Steering Wheel EVIC Switch used to Navigate Cluster Menu is Inoperative. ? No Illumination. ? No Response to button press. This bulletin involves performing a power reset to activate/awaken the EVIC buttons.

"

Falsely.