2017 Ram 1500 TSBs

Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P2072 - Electronic Throttle Control System - Ice Blockage. ? P2110 - Electronic Throttle Control - Forced Limited RPM. ? P2118 - Electronic Throttle Control Motor Current Performance - Bank 1. The customer may also comment on the following: ? The vehicle may not start (below freezing conditions - typically -7 C (-20 F)) This bulletin involves removing the PCV valve and hose to dry out, drying out the throttle body and installing an updated make-up air hose, air cleaner lid and changing the oil.

for replacement as a remedy for fluid leak.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

(DTCs) P0299 Turbocharger Underboost And/Or P026D ? Fuel Injection Quantity Higher Than Expected, Set.

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

If no response in 15 minutes, please proceed with repair. When replacing Radiator for damage on engine side of radiator, also replace fan module and ship the old fan using the same ticket number.

Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.

The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.

Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA, 68046015AA, 68100682AA, 68100676AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair.~ ~___________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

There also may or may not be driveability-related concerns that accompany the Mil-On condition. Upon further investigation, there may be a fault code for P062A-FUEL PUMP CONTROL PERFORMANCE.

Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P1D30-00 - Oil Viscosity Too Low. Attempting to clear the DTC will be unsuccessful. P2453-00 - Diesel Particulate Filter Differential Pressure Sensor Circuit Performance. P0401-00 - EGR Flow Insufficient Detected. P0133-00 - O2 Sensor 1/1 Slow Response. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P0299-00 - Turbocharger Underboost Condition. P0402-00 - EGR Flow Excessive Detected. P245B - EGR Cooler Bypass Control Circuit Performance. P20C6 - Reductant Heater 4 Control Circuit Performance. P208B - Reductant Pump 1 Control Performance. P249C - Excessive Time To Enter Closed Loop Reductant Injection Control. P20E8-00 - Reductant Pressure Too Low. P20E9-00 - Reductant Pressure Too High. In addition, the following software enhancement is available:Ability to enable the ?Fuel System Cleaning? routine in wiTECH.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

(PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received. P062A - Fuel Pump Control Performance. In addition, customers may experience the following condition:When starting a cold engine the vehicle has a rough idle and/or the engine will shut off.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0335-00 - Crankshaft Position Sensor Circuit. P0336-00 - Crankshaft Position Sensor Performance. Customers may also comment on one or more of the following: The vehicle will not accelerate quickly over 80 kph (50 mph) (vehicle is in limp mode). Vehicle periodically stalls.This symptom/condition is caused from missing magnetic material on the crankshaft tone wheel

(PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U1424-00 - Implausible Engine Torque Signal Received. P062A - Fuel Pump Control Performance.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacement part will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.

connections at the number three cylinder fuel injector. Some customers may experience a fuel smell and/or weepage. Upon further investigation, a technician may notice the issue emanating from under the hood at the number three cylinder injector return hose connector.

connections at the number three cylinder fuel injector. Some customers may experience a fuel smell and/or weepage. Upon further investigation, a technician may notice the issue emanating from under the hood at the number three cylinder injector return hose connector.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.

Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.

The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P1D30-00 - Oil Viscosity Too Low. Attempting to clear the DTC P1D30-00 will be unsuccessful. P2453-00 - Diesel Particulate Filter Differential Pressure Sensor Circuit Performance. P0401-00 - EGR Flow Insufficient Detected. P0133-00 - O2 Sensor 1/1 Slow Response. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P0299-00 - Turbocharger Underboost condition. P0402-00 - EGR Flow Excessive Detected. P245B - EGR Cooler Bypass Control Circuit Performance. P20C6 - Reductant Heater 4 Control Circuit Performance. P208B - Reductant Pump 1 Control Performance. P249C - Excessive Time To Enter Closed Loop Reductant Injection Control. P20E8-00 - Reductant Pressure Too Low. P20E9-00 - Reductant Pressure Too High. The following software enhancement is available:Some vehicles may have experienced a slight engine hesitation or lag in acceleration from engine start-up until the engine and exhaust warmed up. This update is intended to reduce the hesitation or lag in acceleration from engine start-up. In addition, the following software enhancement is also available:Ability to enable the ?Fuel System Cleaning? routine in wiTECH.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P1D30-00 - Oil Viscosity Too Low.Attempting to clear the DTC P1D30-00 will be unsuccessful. P2453-00 - Diesel Particulate Filter Differential Pressure Sensor Circuit Performance. P0401-00 - EGR Flow Insufficient Detected. P0133-00 - O2 Sensor 1/1 Slow Response. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P0299-00 - Turbocharger Underboost Condition. P0402-00 - EGR Flow Excessive Detected. P245B - EGR Cooler Bypass Control Circuit Performance. P20C6 - Reductant Heater 4 Control Circuit Performance. P208B - Reductant Pump 1 Control Performance. P249C - Excessive Time To Enter Closed Loop Reductant Injection Control. P20E8-00 - Reductant Pressure Too Low. P20E9-00 - Reductant Pressure Too High. The following software enhancement is available:Some vehicles may have experienced a slight engine hesitation or lag in acceleration from engine start-up until the engine and exhaust warmed up. This update is intended to reduce the hesitation or lag in acceleration from engine start-up. In addition, the following software enhancement is also available:Ability to enable the ?Fuel System Cleaning? routine in wiTECH.

Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P1D30-00 - Oil Viscosity Too Low. Attempting to clear the DTC will be unsuccessful. P2453-00 - Diesel Particulate Filter Differential Pressure Sensor Circuit Performance. P0401-00 - EGR Flow Insufficient Detected. P0133-00 - O2 Sensor 1/1 Slow Response. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P0299-00 - Turbocharger Underboost Condition. P0402-00 - EGR Flow Excessive Detected. P245B - EGR Cooler Bypass Control Circuit Performance. P20C6 - Reductant Heater 4 Control Circuit Performance. P208B - Reductant Pump 1 Control Performance. P249C - Excessive Time To Enter Closed Loop Reductant Injection Control. P20E8-00 - Reductant Pressure Too Low. P20E9-00 - Reductant Pressure Too High. In addition, the following software enhancement is available:Ability to enable the ?Fuel System Cleaning? routine in wiTECH.

(Note: ETL, ETK, ETM, ETN Diesel Engines)

the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.

the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.

the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

in the oil filter cartridges used in the GEN-2, and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application. Although similar in design, the oil filter cartridges used on the GEN-2 and GEN-3 3.0L diesel engines are different in design. Interchanging them may result in premature engine damage over time.

Please contact the following to return parts back to the Quality Engineering Center (QEC): maria.pineda@fcagroup.com(248) 202-5341.

If no response in 15 minutes, proceed with repair. Please wrap back glass frame assembly in replacement part packing material to prevent twisting during shipping and return assembly to FCA Quality Engineering Center for analysis. If any questions, contact Lori Millen at (248) 379-1888.

Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.

stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

&Rear Door

Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.

Before replacing the blower motor please call one of these individuals:~ First call Brad Bartkowicz at cell (586) 808-4114~ If no answer, then call Vince Celli at cell (586) 630-8136~ If not response in 15 minutes, continue with repair.

Before replacing any of the part numbers listed above, please call any of the following people for each vehicle type. (If you don't get an answer within 15 minutes,then proceed with the repair.):~ WD/WK--68224166AB - Front Ken Deneau, cell (248)-765-0288~ 68089094AA - Rear Pat Presti- cell (248) 379-0972~ KL/UF/PF- 68223053AB, 68225055AA Mark Ware, cell (248) 705-3469~ F500- 68093422AB,Matt Sasina, cell (248)-464-4982 or Bryan Bremer cell (248) 429-9014~ RT- 68029719AB - Front, Matt Filipkowski cell (248) 877-9106~ 05183147AA - Rear, Ken Deneau, cell (248)-765-0288

Engineering would like to have both parts returned for analysis. Also, please take a picture of the parts and email the picture, a short discription of the issue, and the last 8 digits of the VIN to Brigitte.Wicks@fcagroup.com. Thank you.

Before replacing the compressor call FCA Release Engineer Mark Briolat at cell (248) 345-0127. If no response in 15 minutes, continue with the repair.

intermittent by driving under heavy throttle will produce a C1494-92 DTC, if yes, please call FCA axle engineering and do not replace the PTU. Bruce Michel at cell (248) 260-8641, or Jian Zhu at cell (248) 379- 1132. If neither answers with 15 minutes then proceed with the repair. ~ If the service 4WD light lamp is on steady then replace the Power Transfer Unit.

information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com

Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data.

If the power steering pump is being replaced because the power steering fluid flow or pressure readings are below specification, the power steering fluid reservoir and cap assembly should also be replaced. Power steering reservoir and cap assembly 52126151AG or later should be used.

or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com

stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

(PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U1424-00 - Implausible Engine Torque Signal Received. P062A - Fuel Pump Control Performance.

Suspect stock of part number: 04627694AAmust be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before17 April, 2017.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacementpart will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.

(PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received. P062A - Fuel Pump Control Performance. In addition, customers may experience the following condition:When starting a cold engine the vehicle has a rough idle and/or the engine will shut off.

(PCM) with the latest available software. Some customers may experience when staring a cold engine the vehicle has a rough idle and/or the engine will immediately shut off.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding.

front fenders of specifically equipped vehicles. of their 3.6L engine and midnight package (Sales Code 22Q) vehicle.

Morand cell: (248) 410-5078 nick.morand@fcagroup.com Joe Lovell cell: (734) 309-6467 joe.lovell@fcagroup.com Engineering is seeking audio recordings of the concern in an effort to root cause and make necessary improvements to future pumps. Please email any audio recording or documentation of when/where/how the pump makes noise to the above emails. If the dealer is located in the Detroit Metro Area, Engineering may send a representative to review with technician. Any information is appreciated. If a response is not received within 15 mins , then proceed with the necessary repair. For JK and DS: Before replacing water pumps for noise issues the heat shield on the catalytic converter needs to be checked to make sure it is not the source of the noise. Check while the engine is fully warmed up. If the heat shield is found to be the source of the noise tighten the bolts and, or add shims/washers as needed.

shut off", please remove the Canister line and Recirculation Line and retest. If the condition continues, tank replacement may be required. Please reference the proper diagnostic materials. Answers to the following questions can assist Engineering in their quality improvements: 1) At what level of fuel in the Tank does the Hard to Fill condition exist? 2) When did the customer start experiencing Hard to Fill condition? 3) Did the condition exist in a particular fuel station? If tank replacement is needed, please contact Sylvia Lopez at Cell (248) 520-9734 prior to replacing the Tank. She will help arrange shipment of the tank back to the Quality Engineering Center. If no response within 15 minutes proceed with repairs

view camera being inoperative, or the radio screen is black or blue when the truck is in reverse, DO NOT replace the rear camera or perform any repairs until attempting to contact Michael Talbert in Engineering Cell (248) 464- 2043, Monday - Friday between 8am - 7pm EST. If your call is not returned within 15 minutes, proceed with the normal diagnostic process

Water pumps are found TNF but the water pump bypass o-ring was pinched resulting in a coolant leak that looks like a failed pump. Please inspect the bypass o-ring before replacing the pump as it is available separate for service.

the Powertrain Control Module (PCM) is up to the latest flash level. If the problem persists with the vehicle up to latest PCM flash level, then proceed on replacing the Fuel Pump Module.

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Enhanced Voice recognition (VR) performance. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements.

Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Fix for radio loses time. Enhanced Voice recognition (VR) performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements.

Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am - 4pm. If you do not get a response within 15 minutes continue with the normal diagnostic procedure. Before replacing the camera, please disconnect and clean harness and camera connector. Clean & dry both connectors. If replacing the camera, please replace wire harness also and return parts to QEC.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

To verify proper functionality, turn on the ignition with no cables or devices plugged into the port. Connect a charging cable to the port, then connect the device. If the device receives power, the port is functioning to design. There are some minor compatibility issues with some charging cables including Apple Lightning cables. For questions regarding the charging port functionality, please call Dave Diovardi at Cell (248) 941-8704 or Rick Gordon at Cell (248) 630-6281.~

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

when vehicles are not equipped with Front Park Assist.

Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

dealership due to a customer complaint of the rear view camera image being too dark or hard to see, or is exhibiting the issue while in for unrelated service, the issue resides in the rear view camera and NOT the radio screen or mirror (depending on vehicle content available), or corresponding wiring. Issues with a fully black screen or a blue screen are separate from this issue and therefore this Tech Tip does not apply. Updated cameras with part number 68274731AE will correct the complaint.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68260866AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 68085880AD, 68085880AF, 68085881AE, 68085881AF, 68085881AG. Replacement part numbers are: 68085880AG, and 68085881AH. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

are receiving this email as you have been identified to have stock on hand or have stock in transit to your dealership. Reports of dealers receiving incorrect fuel pressure sensors packaged as 68210332AA. Correct and suspect parts can be identified visually by the color of the label on the sensors. Correct sensors have white color label on the part whereas the suspect sensors have yellow colored labels. Reference pictures attached for visual identification. Please inspect stock on hand and return any suspect parts found back to your facing PDC using MRA code 02. Replacement parts can be obtained by reordering the same part number. Direct all questions via email to vn83@chrysler.com

The radio should not be replaced for this issue if the fault is stored, if the code cannot be reproduced and no trouble can be found (radio functions properly). In this case it is no impact to the customer in any way. Do NOT replace the radio for this issue. Please contact John Carlesimo at cell (248) 941-8756 if you have any further questions regarding this fault.

contact Michael Wang at cell (248) 701-5351. If no response or contact is made within 15 minutes, proceed with repairs as necessary.

Please identify battery with the last 8 VIN digits along with the 15 digit Medtronic code from the GR-8 tester. If no response in 15 minutes, continue with the repair. Battery needs to be held and not turned in for core charges.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:

have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016.

Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017.

dealership due to a customer complaint of the rear view camera image being too dark or hard to see, or is exhibiting the issue while in for unrelated service, the issue resides in the rear view camera and NOT the radio screen or mirror (depending on vehicle content available), or corresponding wiring. Issues with a fully black screen or a blue screen are separate from this issue and therefore this Tech Tip does not apply. Updated cameras with part number 68274731AE will correct the complaint.

If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

dealership due to a customer complaint of the rear view camera image being too dark or hard to see, or is exhibiting the issue while in for unrelated service, the issue resides in the rear view camera and NOT the radio screen or mirror (depending on vehicle content available), or corresponding wiring. Issues with a fully black screen or a blue screen are separate from this issue and therefore this Tech Tip does not apply. DO NOT replace the radio (part numbers 68271367A$, 68271368A$, 68271364A$, 68270657A$, 68270658A$, 68270659A$, 68270661A$, 68270662A$, 68270663A$, 68270664A$, or 68270665A$) or mirror (part number 68104884A$) to attempt to correct the dark image issue. Updated cameras with part number 68274731AE will correct the complaint.

this is normal and not a defect.

semi and full synthetic oils.

please do NOT add friction modifier to the axle, replace the axle, and contact Ashley Gerebics at cell: (248) 472-6524 to have the axle fast tracked back to FCA. If no response in 15 minutes, proceed with repair.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

If the vehicle is driven for a short period of time the rear axle may develop a whine noise.

If no response is received within 15 minutes, then proceed with required repair.

Inspect pinion bearings for spalling. If spalling is found, replace the axle assembly without removing bearing cup from the housing. Please contact Ashley Gerebics at cell: (248) 472-6524 to arrange fast tracking of the axle to FCA. If no response in 15 minutes, proceed with repair.

Inspect pinion bearings for spalling. If spalling is found, replace the axle assembly without removing bearing cup from the housing. Please contact Ashley Gerebics at cell: (248) 472-6524 to arrange fast tracking of the axle to FCA. If no response in 15 minutes, proceed with repair.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

MasterShield Products in stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers: 82212074, 82212075, 82212076, 82212077, 82212078, & 82213598 . Please return suspect parts back to your facing depot using Return Code 02, before 18 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all suspect stock of following part number: 05026886AJ. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 02 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

If no response is received within 15 minutes, then proceed with required repair.

Call Mike Wicker at cell (248) 821- 9350 with the Fault Code, so we can determine true root cause. If your call is not returned within 15 minutes, please continue with the repair

covers and seat cover repairs.

Please return all stock of part number 68288760AA. Replacement part number is 68288760AB. Replacement parts w ill be available w eek ending 5/6/16. Please return suspect parts back to your facing depot using Return Code 02, before 26 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 68003062AB, 68003083AB, 68003085AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 1PE001W 7AB, 1PE011W 7AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

As per regulatory compliance: Please return follow ing stock of part numbers: 82214711, 82214712, 82214713, 82214714, 82214715, 82214716, 82214717, 82214718, 82214720, 82214721, 82214722, 82214723, 82214724, 82214725, 82214726, 82214727, 82214728, 82214729, 82214730, 82214731, 82214732. Please return parts back to your facing depot using Return Code 02, before 31May, 2016.

Please return suspect stock of following part numbers: 68050625AA, 68050626AA, 68050627AA, 68050628AA, 68050743AA, 68050744AA, 68050839AA, 68050841AA, 68257133AA, 68257134AA, 68264578AA, 68264579AA, 68264580AA, 68264581AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 April, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return parts which have a pacakging date code of July 20th 2016. Reference pictures attached for suspect part identification. Please return parts backto your facing depot using Return Code 02, before 31 August, 2016.

Please return suspect stock of part number 68143886AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 68174065AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 68141880AH, 68141881AH, 68145625AI, 68145626AI, 68189480AF and replacement part numbers are 68141880AI, 68141881AI, 68145625AJ, 68145626AJ & 68189480AG respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 05278632AF and replacement part number is 52030379AA which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 1YG06JSCAC, 1YG06KEPAC, 1YG 06KFSAC, 1YG 06KGZAC, 1YG 06KBUAC and replacement part numbers are 1YG 1YG06KFSAD, 1YG 06KG ZAD, 1YG 06KBUAE respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 68188889AE and replacement part number is 68188889AF which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of following part numbers: 68036213AA, 68036230AF, 68158196AC, 68158197AD, & 68158454AD. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allstock of following part numbers:68241568AB,68241568AC,68241569AB,68241569AC, 68241570AB,68241571A.Replacement part numbersare 68241568AD,68241569AD,68241570AD,68241571AD, which are in stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

This same month last year we had over 40,000 open aged > 5 days tickets. As a result of focused efforts to verify vehicles are repaired and close tickets the number is now at just under 7,000 tickets.

If the vehicle is driven for a short period of time the rear axle may develop a whine noise.

If no response is received within 15 minutes, then proceed with required repair.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Mirror Contacts Door Window Glass In The Folded Position.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

The vehicle was built with tinted glass in the rear backlite. The rear sliding backlite should have clear glass installed.

contact: Chuck Hood at cell (248) 613-7591 If no response in 15 minutes, proceed with repair.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Some customer?s may notice the cup holder insert is missing from left front door panel.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

paint chipping off and replacing all handles if chipping is found. VINs in the attached RRT list require handle replacement without inspection. This bulletin only applies to vehicles with the ?Sublime Green? color paint option (Sales Codes FFB).The customer may comment that the paint is chipping off one or more of the exterior door handles.

possibly replacing the rear door trim panels and inner belt moldings that measure out of specifications. The customer may comment there is a bulging gap between either the left, right or both rear door trim panels and the inner belt moldings.

If you are unable to get a response within 15 minutes, please continue with the repair.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 05182600AC. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock,or have stock in transit to your dealership. Please return all suspect stock of following part numbers:68159725AB,& 68261143AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02,before 27 O ctober,2015. Return any open orders in process too. Direct all questions via email to MO PARQ C@fcagroup.com

LT:04805839AD

To do this, add the LEG (Trailer Tow Mirrors) sales code to the VIN using DealerCONNECT and then performing a vehicle re-configuration using the WiTech tool.~ After Kit is completely installed, perform the following;~ 1. Add LEG sales code to the VIN under the ?Vehicle Option Updates? Found on Dealerconnect~ 2. Update Vehicle Configuration by using the WiTech tool and performing ?Restore Vehicle Configuration.?

stock in transit to your dealership. Please return suspect stock of part number 68160775AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 26 August, 2016.

possibly replacing the rear door trim panels and inner belt moldings that measure out of specifications. The customer may comment there is a bulging gap between either the left, right or both rear door trim panels and the inner belt moldings.

A)

Please return allsuspect stock of part numbers:68212041AC,68141170AC,55112738AA.See attachmentsfor identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Please return all suspect stock of following part numbers: 57010364AI, 57010365AI, 57010504AJ, 57010505AJ, 68224368AB, 68224369AB. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017.

numbers:55395241AG,55395241AE.Replacement ispart number 55395241AH which isin stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 12April,2017

have stock in transit to your dealership. Please return suspect stock of part number 04589131AG, 04589243AG . See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 7 April, 2016.

If you are unable to get a response within 15 minutes, please continue with the repair.

paint chipping off and replacing all handles if chipping is found. VINs in the attached RRT list require handle replacement without inspection. This bulletin only applies to vehicles with the ?Sublime Green? color paint option (Sales Codes FFB).The customer may comment that the paint is chipping off one or more of the exterior door handles.

from the power sliding backlite center glass and replacing the backlitecable assembly. The customer may describe a noise when opening and/or closing the backlite center glass. The noise is described as clicking, popping,or ticking.

from the power sliding backlite center glass and replacing the backlitecable assembly. The customer may describe a noise when opening and/or closing the backlite center glass. The noise is described as clicking, popping,or ticking.

The customer may notice a large gap where the center stack meets the instrument panelFig.1.Gap at Center Stack Trim

The customer may notice the glass cover trim is loose or shows a gap on either of the rear doorFig.1.Gap Identified at Door

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience one or more of the following: Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling. "

730-2758 prior to removing any parts. If there is no response within 15 minutes, please take a close-up picture that clearly shows the damage and send it and the VIN to Jordan.Weber@fcagroup.com, then replace the housing and filler tube as an assembly without further disturbing the rivets holding the housing to the tube. Please return the part to FCA for analysis.

462-0138 prior to removing any parts. If there is no response within 15 minutes, please take a picture of the damage and send it to Sarah.Siddiqui@fcagroup.com, then replace the housing and filler tube as an assembly without further disturbing the rivets holding the housing to the tube. Please return the part to FCA for analysis

an EVAP dual vapor canister filter kit(Mopar part #68478013AA)is available in place of the OEM single vapor canister filter.This kit should not be installed on vehicles driven in normal conditions that are not subjected to the below symptom/conditions. Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience the following conditions:Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

an EVAP dual vapor canister filter kit(Mopar part #68478013AA)is available in place of the OEM single vapor canister filter.This kit should not be installed on vehicles driven in normal conditions that are not subjected to the below symptom/conditions. Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience the following conditions:Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling.

either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 68146401AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock, or have stock in transit to your dealership. Please return following part numbers: CBTTP57FAA, & CBTTP57FAB. Replacement part number CBTTP57FAC will be available week beginning 26 O ct., 2015. There are reports of pre-programmed FO BS in these kits, preventing dealer pairing of W IN and Transmitter Key FO BS. If repair is needed prior to new part availability, order two of part number 05026886AK transmitter Integrated Key FO B. Please return suspect parts back to your facing depot using Return Code 02, before 06 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

(248) 622 8109 ~ Mexican Dealers please call Ricardo Lozada at cell +52 1 55 1370 3187. If no return call in 15 minutes, continue with repair.

please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair.

A customer may experience one or more of the following conditions: Radio display screen will lock up and reset intermittently. Incorrect routing directions to fuel stations when using Travel Link. Unable to turn on heated seats; icon is greyed out. Navigation screen goes blank. Navigation system freezes/locks up. Vehicles with Mopar special edition radio will update radio?s splash screen. Navigation icon shows the vehicle going backward when it?s moving forward.

stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allsuspect stock of part numbers:68148794AH,68148794AF,68148794AD,68156453AH,68156453AF, 68156453AD,68161542AE,68161542AD.See attachment for identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Diagnostic Trouble Codes (DTCs) P208B ? Reductant Pump 1 Control Performance, and/or P20E8 ? Reductant Pressure Too Low, Set.

Diagnostic Trouble Codes (DTCs) P20E8 ? Reductant Pressure Too Low and/or P208B ? Reductant Pump 1 Control Performance Set.

Jeff Pagel at cell (248) 421-3265. If no response in 15 minutes, continue with repair. Send photographs to jeff.pagel@fcagroup.com.

Diagnostic Trouble Codes (DTCs) P20E8 ? Reductant Pressure Too Low and/or P208B ? Reductant Pump 1 Control Performance Set.

Diagnostic Trouble Codes (DTCs) P208B ? Reductant Pump 1 Control Performance, and/or P20E8 ? Reductant Pressure Too Low, Set.

industry awareness regarding the use of recycled or salvage parts.

Diagnostic Trouble Codes (DTCs) P208B ? Reductant Pump 1 Control Performance, and/or P20E8 ? Reductant Pressure Too Low, Set.

Diagnostic Trouble Codes (DTCs) P20E8 ? Reductant Pressure Too Low and/or P208B ? Reductant Pump 1 Control Performance Set.

Diagnostic Trouble Codes (DTCs) P20E8 ? Reductant Pressure Too Low and/or P208B ? Reductant Pump 1 Control Performance Set.

Diagnostic Trouble Codes (DTCs) P20E8 ? Reductant Pressure Too Low and/or P208B ? Reductant Pump 1 Control Performance Set.

Diagnostic Trouble Codes (DTCs) P20E8 ? Reductant Pressure Too Low and/or P208B ? Reductant Pump 1 Control Performance Set.

intended for DS only, and not to be used on DJ or DT. These parts were removed from DJ and DT, since the bed extender obstructs tail lamp visibility requirements at some angles. Installing these parts onto the 2019 or later DJ and DT trucks will violate lighting obstruction requirements.

industry awareness regarding the use of recycled or salvage parts.

Please return suspect stock of following part numbers: 68110016AC, 68110016AD, 68110016AE, 68110017AD, 68236104AC, 68236105AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31 August, 2016.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.

Some customers may experience noise and vibration in vehicle. This is due to improperly torqued transmission extension housing attachmentbolts.

Some customers may experience a less than desirable shift quality or the vehicle stuck in a fixed gear during a limp in mode.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

Module (TCM) with the latest available software. Some customers may experience a less than desirable shift quality or the vehicle stuck in a fixed gear during a limp in mode.The following enhancement is included in the software update: Improved transmission shift quality and allowing the transmission to shift multiple gears during a limp mode condition.

please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

the following scenario occurs; The T79 or U11 recall was completed where the shifter inspection was acceptable and the software flash was performed but then the customer comes back needing the BTSI bracket replaced for coming out of park without the brake or key.

If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any DTCs identified with the scan tool and document them on the repair order.

check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.

Module (TCM) with the latest available software. Some customers may experience a less than desirable shift quality or the vehicle stuck in a fixed gear during a limp in mode.The following enhancement is included in the software update: Improved transmission shift quality and allowing the transmission to shift multiple gears during a limp mode condition.

please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.

Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

This is due to wax or other chemical substance being used on a grain in molded color part. You can clean the applique using isopropyl alcohol. This is not a warrantable condition.

manufacturer Fold-a-Cover at 1-800-322-0522.

manufacturer Fold-a-Cover at 1-800-322-0522.

manufacturer Fold-a-Cover at 1-800-322-0522.

cutting them off prior to installation. This backet is on the front crossmember.

A test-drive snap shot may help you isolate the source of the issue.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

call one of the individuals below.~ Steve Rice at cell (248) 867 0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet.

Please return stock of part number 68103256AG packaged before 2016/08/01. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

interface between brake pedal pin and brake booster eyelet. Use a general all-purpose grease such as MS-4178 used on steering linkages.

to be tucked behind the flange of the bumper bracket. No fasteners are used to attach the liner and the bumper when vehicle is equipped with a steel front bumper.

not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

caliper assemblies including adapters and pads as a unit, unbolting them from the knuckle. Also replace both front rotors, labeling right (RT) and left (LT). Call Mark Randall at (248) 520-3863, if no answer leave a message with last 8 of VIN, dealer code, and mileage. Save the Caliper Assemblies and Rotors for FasTrack return and root cause analysis. If no response in 15 minutes, proceed with repair.

Start Date: 10/27/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of part numbers: 68144663AA, 52013874AE. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to MOPARQC@fcagroup.com

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

If no response in 15 minutes, proceed with the repair.

If no response in 15 minutes, proceed with ordering the part

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Please call Paul Kuehl for further assistance, at cell (248) 535-7013. If no response in 15minutes, proceed with repair, but do not replace bearing(s) unless there is visible damage, see Service Manual Diagnostic Procedure which includes a picture of typical bearing grease weepage.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

alignment to proper specifications. The customer may describe that the headlamps are out of alignment, steering wheel is off-center or may notice premature front tire wear.

alignment to proper specifications. The customer may describe that the headlamps are out of alignment, steering wheel is off-center or may notice premature front tire wear.

Febuary 14 th, 2008, verify that the pitman arm part number is 68039930AA. The part number is embossed on the pitman arm.~If the pitman arm is not a 68039930AA, it must be replaced with a 68039930AA.~ Issue 2: For 2003 to 2007 MY only. If the OE steering linkage has been replaced with 52122362AA, 52122362AB, 52122362AC, 52122362AD, 52122362AE, or 52122362AF and pitman arm 68039930AA the following service parts are available.

as either having stock, or have stock in transit to your dealership. Please return all suspect stock of follow ing part number: 68245351AB. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

B)

technician an overview of the steps a customer will need to take to complete the update.

spare tire winch cable when storing under the vehicle. The adapter is part number 6824863AA and requires three (3) mounting nuts; PN 68150129AA.