2017 MINI Cooper S TSBs

worn.

August 1, 2017 Warranties will only reimburse in exact quantities - the 1/10 liter "billing part numbers" for the applicable bulk engine oil (tanker or drum) that is needed after the completion of an engine repair (partial or full) or when an "Engine oil" maintenance service task is performed.

The following fault code is saved in the IHKA (integrated automatic heating/air conditioning system) control unit: 801189 - Engine mixed air right: Initialization fault.

Warranty Extension For the eligible vehicles, MINI USA, a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the engine radiator's Environmental Air Catalyst (EAC) sensor (shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date.

noise can be heard from inside the fuel tank when the tank is full. The customer may describe this noise as a "helicopter noise" from the rear of the vehicle.

Warranty Extension For the eligible vehicles, MINI USA, a division of BMW of North America, LLC ("MINI USA") is extending the limited warranty for the engine radiator's Environmental Air Catalyst (EAC) sensor (shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date.

more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.

Bulletin (Revision 2) replaces SI M62 01 19 dated January 2019.The central instrument's outer perimeter LED ring (arrows) does not illuminate when switching on the ignition or with the engine start-stop button. It only illuminates after direct actuation of a component (e.g. setting the temperature radio volume etc.). F57 shown; other models similar Software error in the Automotive Pixel Link driver (APIX driver). APIX is the serial high-speed Gigabit multichannel link that connects displays such as the LED ring with vehicle control modules.

display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear. When performing a vehicle test the following diagnostic fault codes are stored in the BDC: CD0420 - "error of Flexray controller on Flexray bus" D91FF9 - "Flexray message data drivetrain 2 (DT_PT_2): Timeout" This message may be read out in the ZGM control unit or Body Domain Controller CAUSE Software in the Body Domain Control unit (BDC).

During load reversal or taking off from a stop there is a creaking or droning noise heard from the lower engine area. CAUSE The bushing in the lower engine stabilizer link is working its way out of its aluminum housing thereby rubbing against the engine oil pan. The bushing in the lower engine stabilizer link (1) is working its way out of its aluminum housing. The aluminum housing starts to rub against the engine oil pan (2).

After engine start the malfunction indicator lamp (MIL) and Check Control message (ID 29) "Engine fault! Power loss" are displayed in the instrument cluster.

After a vehicle has been programmed to an I-level greater than 19-11-5xx and lower than I-level 20-03-530; the safety belt (aka seat belt) acoustic warning sounds when in Park (engine running) and the safety belt is unbuckled. The chime/gong lasts for up to 1 minute 40 seconds. The customer only expects the acoustic warning when the vehicle is moving and the safety belt is not buckled. The acoustic warning can occur when the seat is occupied and the safety belt buckle is opened on the driver's or passenger's side. Software in the ACSM4 Control Unit.

replaces SI M32 01 14 dated October 2016. The power assisted steering is unavailable at start up/drive readiness. No communication with the Electric Power Steering (EPS).

indicator lamp (MIL) and/or a different issue the following fault may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.

The Service Engine Soon (MIL) light is on together with the following fault stored in the Digital Motor Electronics (DME). Fault Code: Control Unit: Fault Code Text: 118002 DME Mixture control: Fuel-air mixture too rich In the situation being described the fault is only stored during the cold winter months. Note: Various other causes for a rich mixture fault are possible and should not be overlooked. DME software diagnostic is too sensitive This situation is most likely to occur if the driving profile is one of frequent cold engine starts and/or primarily short distance trips (idle / low load operation) where full engine operating temperature is not reached Due to the lower engine oil temperatures crankcase vapors that contain a higher fuel content are not completely drawn off via the crankcase ventilation system A false DME adaptation routine could then lead to this fault being set.

droning noise heard from the lower engine area. CAUSE The bushing in the lower engine stabilizer link is working its way out of its aluminum housing thereby rubbing against the engine oil pan.

following fault code is stored in the DME: 1B8004 - EAC Sensor: Temperature - Engine coolant temperature radiator outlet comparison to each other implausible DME software calibration error for EAC sensor diagnostics.

crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.

In the situation being described the fault is only stored during the cold winter months along with the use of winter fuel.

A groaning and/or squeaking noise from the front axle occurs when turning at low speeds or idle. Plastic and elastic deformation of lower ball bearing shell in spring strut support bearing.

One of the following complaints may be reported: The engine runs erratically; The engine causes vibrations when running; Grinding noise from the engine compartment when engine is running.

The engine stalls right after starting (when stationary).

The fault memory lock in Digital Motor Electronics (DME) control unit was not activated. This lock should prevent the manual deletion of permanent fault codes. The DME fault memory lock has not been set.

A groaning and/or squeaking noise from the front axle occurs when turning at low speeds or idle.

INFORMATION Replacing the VANOS gear central bolts or the VANOS gear will require a component inspection when the engine assembly has been previously replaced in one of the vehicles listed above. Ordering the parts via the model, production or VIN may provide the incorrect part numbers. The procedure below will help identify which VANOS parts are installed in the replacement engine. 11 36 7 608 788 Inlet adjustment unit Oulet adjustment unit Refer to the ETK and the repair instructions for one time use fastener and component information regarding additional screws, gaskets and seals.

There is an audible hissing noise from the speakers when there is no active audio source. This noise is most apparent with the engine and climate system fan turned off. Software in the HK HiFi amplifier.

SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

SUBJECT B38 Engine: Mixture Faults Stored in DME and Cylinder Head Cover Leaking Engine Oil.

* On board computer and navigation system goes black or resets. * The engine can only be switched off by pressing the START/STOP button three times (Emergency STOP) * Various Check Control messages are displayed * At a minimum the following fault code is present: D91C86 - CAN message, status functional safety (ST_FSSY): Timeout-BDC * Additional fault messages may also be displayed Software error in the central gateway of the Body Domain Controller (BDC) control unit. Note: Parts replacement does NOT provide a solution!

idle is sporadically elevated (up to approx. 1200 rpm). MIL indicator is illuminated. Fault code 1E0001 - ""Idle speed control: Speed too high"" is stored in DME. CAUSE DME software error The DME software improvements come in 2 steps 1. Primary improvements with I-level XXXX-17-03-50x. 2. Additional minor improvements with I-level XXXX-17-07-50x (ISTA/P 3.62.0 - expected release July 6, 2017 or ISTA NEXT 4.06.1x -expected release June 23, 2017)."

The Service Engine Soon light is on. A Check Control message for ""Engine overheated"" and or ""Exercise caution!"" may also display. The following fault codes may be stored in the DME: 1D2401 - Characteristic map thermostat, actuation: Short circuit to B+ 1D2402 - Characteristic map thermostat, actuation: Short circuit to ground 1D2404 - Characteristic map thermostat, actuation: Line disconnection During diagnosis the coolant may be found to be discolored. Insulation on the wiring for the map activation thermostat (heating element) may be damaged. Exposed wiring may allow coolant to enter the harness. This may cause damage to the heating element."

A groaning and/or squeaking noise from the front axle occurs when turning at low speeds or idle.

The following Check Control Message (CCM) is displayed in the instrument cluster: CCM 350: Driving stabilization. Drive at a moderate speed. The following entry is present in the fault memory of the LMV: 440317 - Pump motor: General multiple fault. Further fault memory entries can occur in combination: DSC: 48068C - Transfer box - clutch closed down temporarily, possible overheating. 48078A - All-wheel drive clutch - clutch position open, only front-wheel drive. LMV: 440304 - Pump motor: Current too low Unfavorable software of the longitudinal torque distribution module (LMV).

A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. F54, F55, F56, F57Target Integration level: F056-16-11-501 or higherThe vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."

A creaking noise is heard from the front end of the vehicle while cornering (predominantly left turns) under the following conditions: Driving In 1st or 2nd gear; While coasting or accelerating; with an Outside ambient temperature that is below 10C (50F); and After engine warm-up, the ambient temperature of engine compartment may exceed 10C (50F) even though the outside temperature is still below 10C (50F). Noise cannot be reproduced during straight-ahead driving.

The Service Engine Soon (MIL) light is on. The following fault is stored in the AISIN EGS module: z CF0486: EGS,PT-CAN2: Line fault/electrical fault It is possible the following Check Control messages could be displayed: z Engine fault! Power loss (CCM ID 29) z Drive faulty! (CCM ID 419) - The transmission is in the emergency program and the engine is running with reduced power. This fault occurs sporadically when the ignition is turned on or the engine started. Unfavorable DME software Only vehicles at the following I-levels are affected: z F056-16-03-50x or F056-16-07-50x.

The Service Engine Soon (MIL) light is on. The following fault is stored in the AISIN EGS module: ? CF0486: EGS,PT-CAN2: Line fault/electrical fault It is possible the following Check Control messages could be displayed: ? Engine fault! Power loss (CCM ID 29) ? Drive faulty! (CCM ID 419) - The transmission is in the emergency program and the engine is running with reduced power. This fault occurs sporadically when the ignition is turned on or the engine started. Unfavorable DME software Only vehicles at the following I-levels are affected: ? F056-16-03-50x or F056-16-07-50x

Information section: defect code, labor operations and additional information are updated . The Service Engine Soon (MIL) light is on with the following fault stored in the DME. ? Fault: 118002 - Mixture too rich In the situation being described, the fault is only stored during the ""cold winter months along with the use of winter fuel."" Various other causes for a rich mixture fault are possible and should not be overlooked. CAUSE ? DME software diagnostic is too sensitive ? This situation is most likely to occur if the driving profile is one of frequent cold engine starts and/or primarily short distance trips (idle / low load operation) where full engine operating temperature is not reached. ? Due to the lower engine oil temperatures crankcase vapors that contain a higher fuel content are not completely drawn off via the crankcase ventilation system. ? A false DME adaptation routine could then lead to this fault being set."

or higher, the engine sound produced by the Active Sound Design control module is louder than prior to reprogramming.

system goes black or resets.

the Digital Motor Electronics (DME).

decelerated, in gear, to a near stop and then accelerated again.

noise heard from the lower engine area

is on with the following fault stored in the DME.

should not be programmed with ISTA 4.10.1x.

motor when the vehicle is unlocked, before the engine is started, or after engine is turned off.

motor when the vehicle is unlocked, before the engine is started, or after engine is turned off.

inner door panel of the front right door in the area of the window frame.

completely sealed, causing a water leak.

production.

production.

Dynamic Stability Control (DSC) unit via the On Board Diagnostic (OBD) socket. The DSC data is not processed correctly in the BDC and therefore cannot transmit any diagnostic requests via the OBD using aftermarket scan tools.

lower A-Pillars near the bottom corners of the windshield. Interference between 2 sheet metal panels.

Dynamic Stability Control (DSC) unit via the On Board Diagnostic (OBD) socket. The DSC data is not processed correctly in the BDC and therefore cannot transmit any diagnostic requests via the OBD using aftermarket scan tools.

In some cases after opening they may not correctly latch. A missing seal on the inner Bowden release cable may allow water to enter the cable sheathing and freeze.

glass in the closed position.

A software error in the FZD (Roof function center).

roads.

A wind noise can be heard from the area of the side view mirrors where the mirrors attach to the front doors. Wind is entering the vehicle from around the foam corner insulation at the side view mirror mounting points.

A wind noise can be heard from the area of the side view mirrors where the mirrors attach to the front doors. Wind is entering the vehicle from around the foam corner insulation at the side view mirror mounting points.

Cavity protection applied to underside of hood is leaking out onto wheel arch trim and grille.

When the key button is pressed to open the rear split doors.

Customer complains wipers are noisy or chattering during wiper operation. CAUSE Wiper arms out of adjustment and/or windshield cowl misaligned.

Customer complains wipers are noisy or chattering during wiper operation.

Customer inquires about tailgate opening process, mentioning: * Trunk/tailgate may open when vehicle is locked. * Trunk/tailgate may open while the vehicle is in motion. * Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.

With either of the sunshades fully opened, there is a rattle noise present when driving over rough road surfaces The sunshade is contacting the roof liner trim.

A squeaking noise can be heard when folding the exterior rear view mirrors in or out. Tolerances in the exterior rear view mirrors

The rubber strip on the rear side window trim may crack. In some cases a gap may be evident on the rubber trim strip. Results are cosmetic- no water leakage or sound intrusion. Combination of unfavorable materials.

Customer desires to have contactless tailgate opening and closing (Smart Opener) deactivated. Function not included in software released.

Cavity protection applied to underside of hood is leaking out onto wheel arch trim and grille. Improper application of Cavity Protection Wax.

Left split door (tailgate) is not able to be opened. When activating remote control unlock, second button push does not unlatch left split door. Contact-less foot opening (Comfort Access) does not unlatch left split door with second foot motion. Left split door lock dimensions are out of tolerance.

Mounting position of service cover is too low and clearance dimensions between the cover and door are too tight.

Locking vehicle with CA button requires two presses, with up to 3 second delay between presses. Body Domain Controller (BDC) software

The ""manually-dimming"" interior rearview mirror does not hold its set position when traveling over rough roads and/or with ""low ambient"" interior temperatures. The pivot ball surface finish does not provide sufficient friction for stable positioning."

Automatic tailgate activation is accompanied by an acoustic warning signal indicating the tailgate is in motion. The warning signal has been reported to be not loud enough to be effectively heard in many environments. Original design concept.

or convertible top linkage collide causing damage to the rear window.

frame.

rear view mirrors in or out.

to the inner door cavity window seal.

to the inner door cavity window seal.

structures with subsequent corrosion

Acoustic abnormality in the area of the recirculated air flap (recirculation flap closing and opening several times). The above may occur individually or in combination.

This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and came in vehicles with option code 609. This uses map North America EVO. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and came in vehicles with option 6UM. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and came in vehicles with option code 609 or 6NP . This uses map North America WAY.

illuminated screen which does not go away after a key cycle or sleep mode. Dead pixels in the Liquid Crystal Display (LCD) diodes. Each individual light pixel on an LCD screen is made up of three diodes- red, blue and green. If all three fail, the pixel will appear as a permanent black dot. Dead pixels can occur as a result of: Blunt force contact to the screen that does not result in a cracked surface Non-functioning diodes Manufacturer defects (e.g., gas bubble).

The vehicle cannot be unlocked using the remote control key button. However, Comfort Access operates normally on the front doors and the tailgate. In addition, the Check Control Message (CCM) for Tire pressure control is present on the Central Information Display (CID). The following fault codes may be stored in the Dynamic Stability Control (DSC) control unit: 480A46 - Tire Pressure Monitor D35694 - Message Missing Software error in the Body Domain Controller (BDC).

During programming several aborts can occur in the head unit NBT EVO (HU-H2).

During an active call the call audio autonomously switching from the vehicle hands-free system to the phone. The Bluetooth connection returns after a vehicle sleep cycle (20 minutes).

During an active phone call the call audio autonomously switches from the vehicle hands-free system to the phone.

The Samsung Smartphone running Android 8.x does not support USB audio playback and/or charging of the device via the USB port.

A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.

The time displayed in the instrument cluster (KOMBI) may lose a few minutes each week and the clock needs to be adjusted periodically.

There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware

""Comfort Access Restricted"" CCM (Check Control Message) is permanently displayed.. The CCM ID: D0h. The comfort access is functioning correctly. No comfort access aerial fault codes stored in the BDC (Body Domain Controller). Software error in the BDC."

The audio head unit has a coding error.

SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: z Apple iPhones z Samsung S6 and the S6 Edge. Connectivity failure examples are: z Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. z Contact List incomplete z General connection failures z Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) z Samsung S6 and S6 Edge device firmware

The time displayed in the instrument cluster (KOMBI) may lose a few minutes each week and the clock needs to be adjusted periodically.

?Import Journey (USB)? submenu item in the Stored Journeys menu of the Navigation system is not working.

A. Navigation system will not start at all or the ""Navigation system starts"" message is permanently displayed. B. While attempting to update the Navigation system's map, it will not update. Subfolder on internal Hard Disk Drive (HDD) is missing."

After pre-delivery check or after instrument cluster exchange, MINI Service Inclusive is displayed although the vehicle does not feature the optional Service Inclusive coverage. Instrument Cluster display error

As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an "update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/407...

Central Information Display (CID), upon connecting to the vehicle:

oil change), the vehicle check is displayed as Due (yellow).

HEAD UNITS CANNOT BE SWAPPED BETWEEN VEHICLES FOR TESTING.

the customer; or it is not possible to locate certain addresses, for instance:

High 2 (NBT EVO) when:

the customer; or it is not possible to locate certain addresses, for instance:

performing ISTA4 programming there is no audio playback.

High 2 (NBT EVO) when:

implausible outside temperature reading.

COMPONENT PROTECTION ACTIVE: If either the NBT-EVO head unit or Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit NBT-EVO to enter a locked mode once it recognizes a different VIN.

As a result, the demand on the batteries has increased. Breakdowns due to an empty battery or problems in the vehicles electrical system can have various causes, most of which are not due to the battery itself. For this reason, a battery replacement will permanently eliminate the problem only in the rarest of cases. The energy diagnosis test module helps to localize these causes. This document covers important information for the dealer on how to handle discharged battery complaints. Without performing the energy diagnosis test plan, the root cause of a discharged battery cannot be identified. In order to properly repair the vehicle the first time, it is very important that the diagnostic test plan is performed to completion; with all results taken into consideration.

securely closed and locked.

There may be a potential issue in the welding process of the HV-modules.

This causes the scan tool to read out only the fault memory that was stored first so that any further faults are not displayed.

The main wiring harness near the Electrical Machine Electronics (EME) connector may chafe on the power electronics or E-machine/ connector under certain circumstances.

Security patches for non-safety critical vulnerabilities in MINI head units Entry Nav Entry Media NBT and NBT EVO.

The malfunction indicator lamp light is on (MIL) with the following fault code stored in the DME.

Security patches for non-safety critical vulnerabilities in MINI head units Entry Nav Entry Media NBT and NBT EVO.

The malfunction indicator lamp light is on (MIL) with the following fault code stored in the DME.

under certain circumstances.

CAUSE Software error in the Automotive Pixel Link driver (APIX driver). APIX is the serial high-speed Gigabit multichannel link that connects displays such as the LED ring with vehicle control modules.

The F60 PHEV has a feature within the climate control menu in the CID which enables setting the future departure/start time for: Parked car ventilation (aka "preconditioning").

While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed CAUSE The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield, And/ or The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. KAFAS camera mounting bracket not secured correctly to the windshield. Notice the spacing between the white outline and the bracket. Possible solutions: Verify the KAFAS camera is installed (seated) properly in its bracket Replace the KAFAS camera Replace the windshield

After the high voltage (HV) charging procedure, the stationary climate control (aka preconditioning) does not work. This is part of the normal design. There is no fault or defect.

Information bulletin supersedes SI M61 01 16 dated April 2016.. Customer complains wipers are noisy or chattering during wiper operation. CAUSE Wiper arms out of adjustment and/or windshield cowl misaligned.

The steering assistance fails after several, consecutive parking maneuvers or sustained hold at the end stop. EPS assistance starts functioning again after a few minutes. And, Fault code 4823FA (""EPS control unit internally overload, reduction in steering assistance"") is stored in the EPS control module. EPS software error (overloading protection function over sensitivity)."

Tank ventilation line and/or hood release Bowden cable may have been damaged. The hood release Bowden cable is unsecured and in contact with the tank ventilation line.

Malfunction Indicator Lamp (MIL) is illuminated. Electrical Machine Electronics (EME) has stored fault code FC 222F96. CC Message ""Malfunction Indicator Lamp"" (CCM ID:34) is displayed."

Due to an error in the OBD diagnostics of the DME software, a marginal catalytic convertor or post catalyst oxygen sensor may not be detected as faulty.

Air bag Warning indicator sporadically illuminates for short intervals when occupants are exiting the front of the vehicle. Check Control messages may be displayed as follows: ""Restraint system driver's side is faulty"" (CC 108) ""Restraint system front passenger is faulty"" (CC 109) ""Functions of air bag, seat belt tensioner and belt force limiter are faulty"" (CC 97) Fault codes may be stored: C95462, driver's seat module (seat position, back rest lock): Communication fault C95463, seat module front passenger (seat position, back rest lock): Communication fault Front seat occupants may sense electrostatic discharge when exiting the seat. Electrostatic discharge disrupts normal communication between seat module and air bag control unit."

cycling the ignition.

or sustained hold at the end stop.

both sides malfunctions.

module - left side malfunctions.

installation.

(predominantly left turns)

inoperative.

programmed with ISTA 4.10.1x and I-level 18-03-511 or 18-03-512.

the memory button is not confirmed by an audible response.

Cluster (KOMBI).

deactivated while the vehicle is in park or neutral. Prior to turning off the A/C, the system was functional and cooling properly. A/C compressor, or The power supply to the A/C compressor is too low.

deactivated while the vehicle is in park or neutral. Prior to turning off the A/C, the system was functional and cooling properly. A/C compressor, or The power supply to the A/C compressor is too low.

The condensate drain hose is blocked by the heat shield - The condensate drain hose is not attached properly to the housing - The condensate drain hose was damaged during installation or previous repair.

INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipment may be an indication of refrigerant/equipment incompatibility with the vehicle's system. Always carefully ascertain the type of refrigerant used in the vehicle's system before performing service. Labels on underside of hood, will detail which refrigerant is used in the air conditioning system. Service the vehicle with compatible recycling equipment ONLY. Attempts to adapt and use incompatible service tools will destroy both the vehicle's air conditioning system and the service tool. Never use any R-12/R134a service tools on R1234yf systems. Tools, such as manifold gauge sets, retain small amounts of refrigerant and lubricant. Attempting to use the same equipment on both R-12/R134a and R1234yf vehicles will contaminate the air conditioning systems. Obtain and use the correct type of refrigerant recovery/recycling machine. Follow the directions included in the machine's instruction manual. WARR

Customer complains of musty odor and/or damp front footwell carpet. CAUSE The A/C condensate drain hose is either blocked by the heatshield or not attached properly to the the housing.

The seat heating in the sports seat may not heat up sufficiently Software error in the climate control panel (IHKA)

The customer reports a foul smell (musty, rotten, and vinegary) when the A/C is first turned on that lasts about five minutes. Micro-filter position too low in the IHKA housing.

Damp front foot-well carpet after long period of air conditioning use. Musty odor in the vehicle (moldy, old socks, laundry room). The A/C condensate drain hose is blocked by the heatshield. The A/C condensate drain hose is not attached properly to the housing. The A/C condensate drain hose was damaged during installation or previous repair.

* With option code SA 530 air conditioning or SA 534 Automatic air conditioning Produced from 2/1/2016 through 9/30/2016. * A/C system contains little or no A/C refrigerant. Contaminants under O-ring seals have allowed refrigerant loss.

evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.

evaporator drips, below the instrument panel, into the passenger's footwell. During assembly, the cover of the fresh air intake was not fully seated when the screws were tightened. This cover can then leak condensation out through the existing gap.

INFORMATION Currently Satellite Radio is provided by SiriusXM for MINI customers. SiriusXM is the only company currently broadcasting Satellite Radio in North America. Satellite radio was broadcast from two different sets of Satellites using different earth orbits. XM uses geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. This is different than Sirius Satellites in a Highly Elliptical Orbit (HEO) which came in to the vehicle at a higher angle to the horizon. As of April 2016 Sirius equipped head units moved to the XM Satellites constellation and now show the same location based cutouts.

INFORMATION Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"". New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI M04 01 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipment may be an indication of ref

Fuel level indicator upper LED does not illuminate even though tank has been filled until autoshutoff.

may be influencing reception quality. MINI is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for MINI customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: ? Do not replace any parts ? Do not program or carry out other work on the vehicle ? Explain to customer about the new Wireless Communications Service (WCS) signalsWhen investigating Satellite Radio cutouts or a temporary loss of reception: ? Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna.

tank.

12,500 may experience premature wear of the left rear brakes. In some cases, there also may be visible damage due to thermal overload.

operating up to customer expectations. Customers can report system errors such as: Vehicle equipped with camera-based ACC, brakes without apparent reason and then does not accelerate When ACC is active, the vehicle does not brake, although it is obvious it should brake; or it even accelerates KAFAS system deactivates independently, due to system limitations that are not clear to the customer KAFAS system cannot be activated due to system limitations that are not clear to the customer When accelerating from a standstill, the vehicle does not automatically start in "Follow mode" Road signs are sporadically not detected Lane departure warning sporadically fails to function For the situations described in this service information bulletin that pertain to normal system limitations, ISTA diagnosis does not show any relevant fault codes stored.

When attempting to stow the convertible top it does not compress into a fully locked position on the left side. This prevents the soft-top bow cover from moving forward into proper operating position as shown in video 54 01 17. Additionally a warning gong sounds and a Check Control Message "Roof not locked" appears. One or both can apply: An issue with the convertible top assembly gripper hook Improper adjustment of the convertible top storage spacer adjustment bolt Damaged folding top felt pad.

Currently Satellite Radio is provided by SiriusXM for MINI customers. Satellite radio is broadcast from two different sets of Satellites using different earth orbits. XM uses geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. This is different than Sirius Satellites in a Highly Elliptical Orbit (HEO) which currently come in to the vehicle at a higher angle to the horizon. As of April 2016 Sirius equipped head units will move to the XM Satellites constellation and will show the same location-based cutouts. SiriusXM is currently updating the repeater network to cover areas of low reception, but the general disadvantage of geostationary satellites can't be compensated completely. Buildings, hills, trees, highway sound blocking walls or any other obstacles might block the satellite signal coming from the south at a 32 degree elevation angle and might cause audio dropouts in absence of terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets flatter. Adverse weather conditions will affect reception. Sirius XM will increase the amount of Sirius and XM repeaters gradually to improve situation in metropolitan areas. When investigating Satellite Radio cutouts or a temporary loss of reception: z Please compare to a similarly equipped vehicle. z Do not compare an XM equipped vehicle to a Sirius equipped vehicle. z Replace no parts Customers should direct all reception complaints to MINI Customer Relations department at 1-866275-6464 Customers must provide: z the exact location (street address or Latitude/Longitude) of dropout z weather conditions z time of day the drop occurred. Customer Relations will collect the locations of the XM reception c

September 2016 and SI M64 02 14 dated August 2016 are being combined to prevent duplication of effort and streamline the repair. The customer reports one, or both, of the following: ? Damp front foot-well carpet after long period of air conditioning use. ? A foul smell (musty, rotten, and vinegary) when the A/C is first turned on for a short time. The condensate drain hose is not properly draining the condensate from the vehicle. The micro-filter is absorbing condensate water from the evaporator housing.

Corrosion on inner door panels at the following holes and cavity openings: Door brake (1). Door wiring harness pass-thru (2).

1. DSC's fault codes stored from two different wheel speed sensors (both front or both rear): 4809B0 - wheel speed sensor - front left - drive off recognition faulty and 4809CD - wheel speed sensor - front right - drive off recognition faultyor 4809B9 - wheel speed sensor - rear left - drive off recognition faultyand 480686 - wheel speed sensor - rear right - drive off recognition faulty. 2. Next ignition ON (after above codes stored). a) DME fault can occur:1F054D - drive, safety function: Drive power output reduced, DSC signals implausible and b) Malfunction Indicator Lamp (MIL) may light up. Faulty drive off recognition due to: a towing operation with a raised axle operation of the vehicle on the vehicle hoist operation of the vehicle on the roller test stand DSC diagnosis recognizes implausible wheel speeds, so no control is possible. DME fault is entered on safety grounds since the DSC fault still exists after a terminal change and may only be removed while driving.

ABS/DSC lamps lit in instrument cluster. Fault codes may be saved in the DSC control unit: 480AAD - wheel speed sensor - rear left - smoke monitoring 480AAC - wheel speed sensor - rear left - unexpected jump in the signal 4809B9 - wheel speed sensor - rear left - driving off recognition faulty 480716 - wheel speed sensor - rear left - plausibility: direction of rotation 4809B7 - wheel speed sensor - rear left - missing tooth 480719 - wheel speed sensor - rear right - plausibility: direction of rotation 480686 - wheel speed sensor - rear right - driving off recognition faulty 480AB3 - wheel speed sensor - rear right - unexpected jump in the signal 480AB4 - wheel speed sensor - rear right - smoke monitoring 4809C2 - wheel speed sensor - rear right - missing tooth Rear wheel pulse generator (wheel speed sensor) retaining screw is loose, missing or broken.

12,500 may experience premature wear of the rear brakes.

boots.

This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, MINI Assistance and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.

process for shipping claim-related "return requested" parts which asre classified as "Dangerous Goods" (DG)

ConnectedDrive/MINI Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or MINI Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE In order to assist with your ConnectedDrive issue as quickly as possible, a checklist has been developed which provides all the essential information to the support team. Any requested information that is missing from the checklist will delay the resolution of your issue.

Cracking noise coming from the area of the front axle when driving over rough road surfaces, railroad crossings and speed bumps. CAUSE Wishbone rubber mount.

not cause chafing of the convertible top fabric at the c-pillar area as shown below.

Due to hardware changes in the AISIN GA6F21AW or GA8F22AW transmissions.

A Check Control Message could intermittently be displayed indicating a Start/Stop Function failure. Vehicle may not restart after stopping. The following fault is stored in the DME: Fault 20BA20: clutch switch, signal: missing In addition the BDC may have the following fault stored: Fault 804084: clutch switch, plausibility fault compared to CAN signal This can occur if for example 14 gears changes are made, but the upper clutch position switch is only activated 10 times. This difference could occur when the clutch pedal is not being fully released between gear shifts or by resting a foot on the pedal so the upper switch position is not recognized.

The cap was not installed correctly during assembly.

The cap was not installed correctly during assembly.

During assembly oil may have contaminated the mounting points of the tail light assembly.

The tail light mounting brackets may be cracked or broken. During assembly oil may have contaminated the plastic housing of the rear tail lamps causing damage to the mounting points of the tail light assembly.

The tail light mounting brackets may be cracked or broken. During assembly; oil may have contaminated the plastic housing of the rear tail lamps; causing damage to the mounting points of the tail light assembly.

e.g., parking lot maneuvers) or accelerating with a medium to large steering angle: Humming or creaking noises from the rear area; slight vibrations, also noticeable from the driver's seat; the vehicle may also jerk slightly.

SUBJECT Noise from Steering Column Switch Center when Turning. The customer states that there is a grating or scraping noise when the steering wheel is turned. The noise comes from the area of the Steering Column Switch Center (SZL). When turning the steering wheel, the connection between the steering wheel and the SZL causes torsion stress, creating interference noise.

Horn may operate: with a delay after actuation only after pressing on switches very firmly. after repeated, forceful actuation. only when using one or two (of the four) switch contact points ? Only F54, F55, F56, F57: Dissimilar metal corrosion between horn switch contacts and airbag unit. All models: routing of the connecting wires on the steering wheel incorrect

No communication with the Electric Power Steering (EPS). Multiple possible fault codes. Cause: Electric Power Steering (EPS). Perform a vehicle test with ISTA to identify fault code entrie

The new wheel electronics are identified as Huf Generation 5. These new wheel electronics will need to be programmed using the new tool when replaced or when depressurized (0 psi) for more than 2 minutes.

the front driver's or passenger's seat during forward/back seat adjustment.

the front driver's or passenger's seat during forward/back seat adjustment.

Center console storage compartment lid requires too much force to open as demonstrated in accompanying video. tinyurl.com/mkphrma A. Sticky release mechanism. And/or B. Improper alignment.

February 2017.

The airbag indicator light illuminates after replacing the CIS (Capacitive Interior Sensing) mat.

During low outdoor temperatures, with the doors and windows closed, a metallic whirring noise is detected in the area of the head air bag (HPS).

A PVC seam of the front strut spring tower may not be providing the necessary corrosion protection. Improper application of seam sealer. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

INFORMATION Please refer to the Electronic Parts Catalog (EPC), using the VIN to locate the part numbers.

activated.