2023 Kenworth T280 TSBs

Loss of communication between the right-hand shift stalk and the vehicle may result in the vehicle being disabled after it comes to a stop, thereby increasing the risk of crash or injury. A warning will appear on the dash display when communication is lost, including transmission or engine warnings, ! next to DNR/DNRP indicator, - in the DNR/DNRP indicator, and/or chimes, depending upon whether you are operating a diesel/gas or battery electric vehicle.

The right-hand shift stalk may have an improper wire harness terminal crimp within the wire harness connector. Loss of communication between the right-hand shift stalk and the vehicle may result in the vehicle being disabled after it comes to a stop, thereby increasing the risk of crash or injury. A warning will appear on the dash display when communication is lost, including transmission or engine warnings, ! next to DNR/DNRP indicator, - in the DNR/DNRP indicator, and/or chimes, depending upon whether you are operating a diesel/gas or battery electric vehicle.

Loss of communication between the right-hand shift stalk and the vehicle may result in the vehicle being disabled after it comes to a stop, thereby increasing the risk of crash or injury. A warning will appear on the dash display when communication is lost, including transmission or engine warnings, ! next to DNR/DNRP indicator, - in the DNR/DNRP indicator, and/or chimes, depending upon whether you are operating a diesel/gas or battery electric vehicle.

Loss of communication between the right-hand shift stalk and the vehicle may result in the vehicle being disabled after it comes to a stop, thereby increasing the risk of crash or injury. A warning will appear on the dash display when communication is lost, including transmission or engine warnings, ! next to DNR/DNRP indicator, - in the DNR/DNRP indicator, and/or chimes, depending upon whether you are operating a diesel/gas or battery electric vehicle.

Control Unit (VECU) part number Q21-1157-013-011 / Q21-1157-013-013. Parts and procedures for Phase 2 chassis will be available at a later date. This bulletin will be updated at that time. Please refer to the condition section for more details. Certain Ethernet Multiplexed Architecture (EMUX) chassis fail to conform to Federal and Canada Motor Vehicle Safety Standards (FMVSS/CMVSS) No. 108. Delayed or unsteady illumination of the vehicles stop lamps, reverse lamps, turn signal lamps and inadvertent change in headlamp illumination or lift axle position may"

The magnet carrier acts as the pivot for the throttle pedal. An oversized magnet carrier may cause the throttle pedal to stick. If the throttle pedal fails to return to idle, or sticks, it may increase the risk of a crash. Drivers may feel sticking or that the pedal doesnt return to idle once released. Pressing the service brake will overcome a stuck throttle pedal and allow the vehicle to stop. This bulletin will be updated when parts and procedures are available.

Safety Recall Certain T280/T380/T480 chassis built with 2.1m Medium Duty End of Frame Trailer Connections and Tractor Protection Valves may not meet the standard trailer brake release timing requirements by 0.5 seconds. A delay in the trailer brake release may create momentary instability to the trailer and increase the risk of a crash.

Kenworth has determined that a safety defect exists in certain Model Year 2021-2024 T280, T380, and T480 chassis with air brakes. The brake pedal plunger which connects the brake pedal to the brake valve may dislodge after the pedal is fully depressed, and rapidly released (side slip foot brake release). If the plunger in the brake pedal assembly dislodges, the driver may be unable to apply the service brakes, which may increase the risk of a crash.

Cummins X15, X12, ISX12, ISX12N, L9N, PX-7, and PX-9 engines The technology will leverage the existing Remote Diagnostic cs hardware to deliver secure software updates remotely. This will reduce downtime and save on maintenance costs for eligible vehicles.

procedure has been updated with additional note boxes for clear instructions. PB: The repair procedure has been updated with additional note boxes for clear instructions."

Support Order Inquiry case.

the end customer.

Greenhouse Gas (GHG) labels available for installation.

Part numbers E0l-1012 (Adapter, Jack TX-8), E0l-1014 (Front Seal Installer), and E0l-1015 (Rear Seal Installer) are currently available to order

This bulletin will be updated once repair parts are available. The right-hand shift stalk may have an improper wire harness terminal crimp within the wire harness connector. Loss of communication between the right-hand shift stalk and the transmission may result in the vehicle becoming disabled after it comes to a stop thereby increasing the risk of crash or injury. A transmission fault will appear on the dash display if communication is lost.

Kenworth has determined that a safety defect exists in certain Model Year 2023-2024 T280, T380, and T480 chassis with TX-8 transmissions and flange mounted yokes. A locking feature may not be installed on fastener threads. This may allow the driveline fasteners to become loose, increasing the risk of a crash or injury.

2 chassis added to the chassis list. Peterbilt: Dealers should check the chassis list and SIR weekly for VIN changes. 10 chassis added to the chassis list."

chassis that were delivered with a Prewire sales code due to parts shortages. Ordering and installation procedures are included.

This could result in loss of mirror glass, reducing rear visibility and increasing the risk of an accident or injury. Missing mirrors cause non-compliance with FMVSS 111 / CMVSS 111. Mirror glass lock rings must be inspected and, if necessary, reseated.

part number Q21-1157-013-011 / Q21-1157-013-013 / Q21-1157-002-002 / Q21-1157-004-004 / Q21-1157-006-006 / Q21-1157-009-009. See attached Parts Matrix for required parts per chassis.

Refer to Sales Bulletin TE2680 for details.

The Exterior Lighting Switch (ELS) in certain T180/T280/T380/T480 chassis may not function and can be reset only by a key cycle. This issue may result in non-compliance with FMVSS/CMVSS 101 and 108. Affected chassis must have the Vehicle Software updated.

function and can be reset only by a key cycle. This issue may result in non-compliance with FMVSS/CMVSS 101 and 108. This bulletin will be updated when software and programming procedures are available."

is no longer compatible.

It must be used if safety recall 25PACF is performed prior to or at the same time as this repair since the 25PACF remedy also satisfies this safety recall.

Connections may not meet the standard trailer brake release timing requirements by 0.5 seconds. A delay in the trailer brake release can create instability to the trailer and increase the risk of a crash. Parts and repair procedures are not yet available. This bulletin will be updated when a repair path is determined.