2018 Jeep Cherokee TSBs

Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked.

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block."

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Diagnostic Trouble Code (DTC) C14A7-97 PTU Motor Component Or System Operation Obstructed Or Blocked, Set.

pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

installed in the vehicle.

oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC):P06EF - Engine Restart Performance. Customers may experience the following:Long engine crank after an Engine Stop/Start (ESS) event.

cluster and/or the following DTCs are present indicating loss of communication with the shifter: U0103, U0103-87. Prior to beginning any repair, please call John Zbranchik at 248-576-0756 or Pablo Flores at 248-576-3972. If no reply contact Dil Weerasinha at 248-944-5967 or Jay Nagle 248-576-5657. If you are unable to contact any of the above, and all the DTCs related to loss of comm are STORED, first perform a vehicle scan with a wiTECH tool or similar and email the log to john.zbranchik@fcagroup.com and pablo.flores1@fcagroup.com. Ensure all stored DTCs in the vehicle are recorded in the log. Use the tool to clear all codes and ensure the ?Service Shifter? message does not return. If this is the first occurrence of this issue on this vehicle, do NOT replace the shifter at this time. If any DTCs related to loss of comm with the shifter are ACTIVE, a full bus log is highly desired. Please contact a regional tech representative to acquire this log. After the log is acquired, or if this is not feasible, check for loose/bent pins, spread terminals on both the male pin cavity in the shifter and the female connector from the body harness take out and all grounds. If no issues are found, replace the shifter and return it to the Quality Engineering Center (QEC).

verified as either stored or active please contact Pablo Flores in FCA Chassis Engineering at cell (248) 979-7062. If no response in 15 minutes, proceed with repair. For additional repair see NOTES below: NOTE 1: If DTC P1C86-1D is still active after inspecting harness connections from Service Procedure (STEP 2). DO NOT replace SHIFTER ASSEMBLY. Instead, replace PRNDM bezel only. NOTE 2: After replacing PRNDL Assembly, clear DTCs and check to confirm DTC does not return. Please return parts back to FCA Engineering if PRNDM is deemed non-functional after performing this Tech Tip. For 2015-2018 KL ONLY; If vehicle DTC Code P1C86-1D (PRNDL Display Current out of Range) is verified as either stored or active please contact Pablo Flores in FCA Chassis Engineering at cell (248) 979- 7062. If no response in 15 minutes, proceed with repair. For additional repair see NOTES below: NOTE 1: If DTC P1C86-1D is still active after inspecting harness connections from Service Procedure (STEP 2). DO NOT replace SHIFTER ASSEMBLY. Instead, replace PRNDM bezel only. NOTE 2: After replacing PRNDL Assembly, clear DTCs and check to confirm DTC does not return. Please return parts back.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC):P06EF - Engine Restart Performance. Customers may experience the following:Long engine crank after an Engine Stop/Start (ESS) event.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC):P06EF - Engine Restart Performance. Customers may experience the following:Long engine crank after an Engine Stop/Start (ESS) event.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC):P06EF - Engine Restart Performance. Customers may experience the following:Long engine crank after an Engine Stop/Start (ESS) event.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

Upon further inspection, fault code P219A - Bank 1 Air-Fuel Ratio Imbalance may be found in the powertrain control module (PCM) as pending, active, or stored. Other fault codes P1066, P1068, P106A, or P106C (Solenoid Valve Switch Off Time Out of Range) may also be stored. Customer may also complain about loss of power or engine running rough while P219A is active.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

dealers only Engineering is seeking information regarding engine operation. Before replacing a Tigershark equipped 2017/2018 KL or MP. Please call FCA Redacted Content . Have VIN last 8 and engine serial number available (located on sticker on valve cover - example TZEP1171811106.) If no response in 15 minutes, proceed with repair.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Tire Pressure Sensors Values Are Not Displayed

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Detected Message

awareness regarding the use of aftermarket parts.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

industry awareness regarding the use of recycled or salvage parts.

A U11E9, or B16FB-15 may be set

A U11E9, or B16FB-15 may be set

A U11E9, or B16FB-15 may be set

seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

seat side shields are replaced the buckle will need to be replacedas well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle willneed to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle will need to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

seat side shields are replaced the buckle will need to be replacedas well. If only the buckle needs to be replaced the front seat side shield will need to be modified. The technician will need to know the following: When either of the front seat side shields are replaced the buckle willneed to be replaced as well. If only the buckle needs to be replaced the front seat side shield will need to be modified.

Module (TCM) withthe latest available software. Customers may experience the following:Longer than usual shift times when performing garage shifts (P to R and Rto D). Poor shift quality or ?bump? experienced during foot on throttle2-1 downshift.

Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. 68550586A$ service RDMs have a 20 clutch plate design Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. All new service RDMs are shipped with the new pump design. If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). Use 68540645AA for the 24 plate RDM with a new pump. Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M

Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. All new service RDMs are shipped with the new pump design. If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). Use 68540646AA for the 24-plate RDM with a new pump. Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti

68249191A$), KL (Part # 68399021A$) and RU (Part # 68217322A$) needs to be followed. Service Instructions for the Condition of a TOC fluid leak: 1) Mark the leakage area if visible to assist in diagnosis and determination of the area where the leak has occurred. 2) If fluid leak was caused by damage or leakage at the transmission oil cooler: - Replace transmission oil cooler - Test drive and verify no additional fluid leaks 3) If fluid leak was caused by leak at quick connect fittings: - Replace transmission oil cooler lines - Test drive and verify no additional fluid leaks

Customer may experience a undesirable or long 5-4 shift during a vehicle coast-down.

Customer may experience a undesirable or long 5-4 shift during a vehicle coast-down.

Customer may experience a undesirable or long 5-4 shift during a vehicle coast-down.

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

Verify that glass run seal is clear and clean of any dirt or debris, and make sure glass is in window track/window glass run seal, then roll window up and down fully 3 times to verify the issue repeats. Clean window track, window, and glass run seal if dirt or debris is found. If window is not in window track or inside glass run seal, repair condition using original glass run seal if no deformities are found in the seal. If glass run seal is deformed, replace glass run seal and ensure seal is fully installed in door channel prior to glass reinstallation. If lubricant is needed during repair, use Mopar part # 04773427A$or 05019059A$ (approved Krytox lubricantfor weatherstrips). For additional information contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet.

If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.

If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

B)

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.