2023 Hyundai Santa Cruz TSBs

This bulletin provides the inspection and repair procedures for vehicles exhibiting this condition. All internal combustion engines consume engine oil as part of normal engine operation. Oil consumption rates may vary based on mileage, operating conditions, driving habits, and maintenance history. Hyundai recommends following the prescribed maintenance schedule and periodically checking the engine oil level using the dipstick to maintain proper engine oil level.

return to the designated park position due to a loose wiper motor crank arm nut. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, the warranty coverage for the Wiper Motor Crank Arm Nut under these conditions has been extended to 10 years/100,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

park position due to a loose wiper motor crank arm nut. Hyundai is extending the warranty coverage for the wiper motor crank arm nut under this condition to 10 years / 100,000 miles from the date of original retail delivery or date of first use (whichever comes first) and is valid for original and subsequent owners. Follow the procedure in Technical Service Bulletin (TSB) 26-BD-007H to replace the wiper motor crank arm nut to address this condition.

park position due to a loose wiper motor crank arm nut. Hyundai is extending the warranty coverage for the wiper motor crank arm nut under this condition to 10 years / 100,000 miles from the date of original retail delivery or date of first use (whichever comes first) and is valid for original and subsequent owners.

park position due to a loose wiper motor crank arm nut. Hyundai is extending the warranty coverage for the wiper motor crank arm nut under this condition to 10 years / 100,000 miles from the date of original retail delivery or date of first use (whichever comes first) and is valid for original and subsequent owners. Follow the procedure in this bulletin to replace the wiper motor crank arm nut to address this condition.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

P218100 that is related to the Integrated Thermal Management Module (ITM). Follow the service procedure outlined in this bulletin to replace the ITM with a revised part and update the Engine/Electronic Control Unit (ECU).

transmissions (8WDCT) and associated transmission control unit (TCU). These changes only apply to vehicles equipped with Theta 2.5T engines. Certain transmissions (indicated by a new part number) have received an improved clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise drivability concerns may occur.

service procedure and replace the related solenoid and harness.

transmission (8WDCT) replacement is necessary related due to high pressure electric oil pump (HP EOP) DTCs P1C2D03 (HP EOP Motor Position Sensor), P193B79 - HP EOP Performance, P0868 - Transmission Fluid Pressure (TFP) Sensor Low. Replace the 8WDCT under this bulletin.

service procedure and replace the related solenoid and harness.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 2nd Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

system.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

system.

system.

system.

of no audio or intermittent sound from the vehicle's speakers.

vehicles equipped with an external amplifier.

equipped with an 8-speed wet dual clutch transmission (8WDCT). The software update revises the touch point learning variation, improving drivability and judder symptoms. Some 8WDCTs (indicated by a new part number) received an updated clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise, drivability concerns may occur. This service procedure should be performed prior to any 8WDCT replacements done for drivability/judder concerns.

pressure electric oil pump (HP EOP) DTCs listed below. This bulletin provides the service procedure to update the Transmission Control Unit (TCU) with improved logic to address these DTCs and enhance operation of the 8DCT.

clutch transmission (8WDCT) when the vehicle sets one of the high pressure electric oil pump (HP EOP) DTCs listed below. This bulletin provides instructions to replace the 8WDCT.

(transmission clutch slip in gear above limit) listed on Page 2.

equipped with an 8-speed wet dual clutch transmissions (8WDCT) that improves the touch point learning variation. Certain 8WDCTs (indicated by a new part number) received an improved clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise drivability concerns may occur.

Pump) connector when servicing the 8-speed wet dual clutch transmission (8WDCT). If moisture enters the HF EOP connector, this can result in corrosion and insufficient connection of the terminals.

(DCT) and associated transmission control module (TCM). Additional steps, not in the service manual, are required within GDS prior to replacing the DCT/TCM, otherwise drivability concerns and/or DTCs may occur.

and/or has a v-gap that is present when closed. This may be due to a broken or missing clip on the underside of the tonneau cover. This bulletin provides instructions to inspect and, if necessary, repair the tonneau cover function using the Tonneau Cover Repair Kit or by replacing the tonneau handle and latch assembly.

This may be due to a broken or missing clip on the underside of the tonneau cover. This bulletin provides instructions to inspect and, if necessary, repair the tonneau cover function using the Tonneau Cover Repair Kit or replacing the tonneau handle & latch assembly.

This may be due to a broken or missing clip on the underside of the tonneau cover. Follow the instructions in this TSB to inspect and, if necessary, repair the tonneau cover function using the Tonneau Cover Repair Kit.

where the tonneau cover does not retract properly and/or a V-Gap is present when closed.

2022 2023MY Tucson (NX4A) and Santa Cruz (NXT) vehicles. If a vehicle exhibits this paint peeling condition, replace the front door trim panel assembly.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

This causes the sunroof to become inoperable. This bulletin provides information to program sunroof operation.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

cover not opening (does not unlatch when unlocked and the handle is in the open position) or not closing (does not latch when pulled closed and the handle is in the closed position).

This may be caused by worn rear self-leveling shock absorbers. Follow the procedure in this bulletin to identify the source of the noise and replace the rear shock absorbers on affected vehicles.

This bulletin describes the procedure to inspect the brakes, resurface or replace and perform a brake burnishing procedure.

Follow the procedure outlined in this TSB to replace the oil level sensor and gasket to complete the service campaign.

P2181 that is related to the Integrated Thermal Management Module (ITM). Follow the service procedure outlined in this bulletin to replace the ITM with a revised part and reprogram the powertrain control module to update the control logic.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

exhibit paint imperfections such as: sag, bubble, blemish, crater, or dirt.