2018 Ford Explorer TSBs

Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking for an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Confirm FPCM connector (Explorer - C3239, Transit - C433, F-150 - C460/C4336, Expedition/Navigator - C433/C4033) is fully seated and inspect applicable grounds (Explorer  G302, Transit - G401, F-150 - G401, Expedition/Navigator - G403/G406) prior to performing guided diagnostics or replacing any components.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer  G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.

(Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level using the Integrated Diagnostic System (IDS). Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.

diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer  G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Diagnostic Trouble Codes (DTCs) P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2022 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

electrical terminals, if affected, to ten (10) years of service or 150,000 miles from the warranty start date of the vehicle, whichever occurs first.

symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.

DTC P025A And/Or DTC U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds(F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2021 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2021 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.

display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN (HS-CAN for Taurus) network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper network communication. If proper network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00 for diagnostics.

unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.

display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper HS2-CAN network communication. If proper HS2-CAN network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00, PPT AL for diagnostics.

This may be caused by a lack of retention of the clips securing the roof rail covers. To correct the condition, follow the Service Procedure to replace the retaining clips and apply adhesive to the roof rail covers.

This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".

Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.

App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

ignition on after a remote start event. The seat back heats properly while the lower seat cushion does not. To correct the concern, reprogram the driver seat module (DSM) using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.

This may be caused by a lack of retention of the clips securing the roof rail covers. To correct the condition, follow the Service Procedure to apply adhesive to the roof rail covers.

Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

in the Ford Pass/Lincoln Way mobile app advising, Your vehicles software is being updated. Vehicle controls will be unavailable for about 10 minutes while this update takes place. This may be due to the TCU still in factory mode. Using the appropriate Ford diagnostic scan tool, check the TCU_AUTHSTATE PID status showing Factory Mode. To correct this condition, perform programmable module installation (PMI) on the telematics control unit (TCU). Once PMI is completed, ensure the TCU_AUTHSTATE PID in service tool no longer displays Factory Mode. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM) section 415-00. For claiming, use causal part 14G229.

Nautilus, and 2013-2019 MKZ vehicles equipped with Multi-Contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section

Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Diagnostic Trouble Code (DTC) P025A Some 2018-2019 F-150, Expedition, Navigator, Transit and Explorer vehicles may exhibit an illuminated MIL with DTC P025A stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harnessto the fuel pump driver module (FPDM) connector. Confirm FPDM connector (F-150 C4336, Expedition/Navigator C433, Transit C433, Explorer C3239) is fully seated prior to performing PC/ED diagnostics or replacing any components. APPLICABLE VEHICLES

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.

exhibit a crank/no start condition, inoperative trailer tow lighting and/or inoperative power telescoping mirrors. This may be due to a concern within the battery junction box (BJB) relay module. A lower level service part has been released to allow for replacement of just the BJB relay module instead of the BJB harness. F-Super Duty part number HU5Z-14A067-A, Continental part number GU5Z-14A067-C, Explorer part number FU5Z-14A067-A, Police Interceptor Utility part number GU5Z-14A067-B.

When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes prior to programing. Delete all previous session files for the vehicle and do not install the TCU fuse until a new IDS session has been started. Once the new session has been started and the fuse reinstalled, the TCU can be programmed. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

During the installation of certain police accessories by non-Ford vehicle upfitters, wiring connector C134 may have been left disconnected following the removal and installation of the front bumper cover. If this issue is noted, first check C134 before beginning other diagnostic steps. Reconnecting C134 due to improper reassembly by an outside supplier is not a warrantable repair.

(Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

after 1 minute during a remote start event when the customer expects the A/C to remain on. To resolve the concern, reprogram the heating, ventilation and air conditioning (HVAC) control module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

(Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.

Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.

To program the fobs, start an IDS session and enter the Red Toolbox > Module Programming > Programmable Parameters > Police Mode > Remote Keyfob Learn > Enable. Next, refer to the RKE Transmitter Programming procedure listed in Workshop Manual (WSM), Section 501-14 > General Procedures to program the fobs. If the RKE fobs fail to program, verify that the fobs are the correct part number. If the fobs are correct for the vehicle, then refer to the inoperative key fob diagnostics outlined in WSM, Section 501-14. This procedure and part numbers do not apply to 2015 and previous model year Police Utility vehicles. Blue lift gate button fobs are part No. GB5Z-15K601-C and red panic button fobs are part No. GB5Z-15K601-A.

Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes then reinstall. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

Customer concern of a vibration or rough idle in D or R Shudder while driving Lack of engine RPM Low performance, lack of acceleration on take off"

refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.

proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Extended Warranty Coverage Updated Owner Letters: 20N07/20B27 S1

Control Module Reprogram Submitting Owner Letters

Covered by this Program: all open / unrepaired vehicles from 21B05 (Police Interceptor Utility Vehicles) have been added to 21N01 as 21B05 expires August 31, 2022. Owner Notification: Police Interceptor Utility owners who have not completed 21B05 will be mailed a letter describing this change.

Supplement: Program terms will be in effect through August 31, 2023 This program is now eligible for mobile repairs

the vehicle is in drive (D) or reverse (R). The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure to replace the torque converter and specified internal transmission components that may have been damaged.

Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.

If diagnostics lead to a motor replacement, visually inspect the original motor for signs of water intrusion. If found, determine source of water leak prior to replacing the motor. Refer to Workshop Manual (WSM), Section 501-17, Pinpoint Test A for 2011-2016 and Pinpoint Test B for 2017-2022 for identifying the source of the water leak.

Date: Ending build date for Chicago Assembly built vehicles has been updated

to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.

investigation by Ford Motor Company to obtain field parts for testing. Ford is voluntarily conducting this program to replace both rear toe links and wheel knuckles on vehicles always registered and always residing in the Detroit (and Toronto) area. The replacement toe links and knuckles being installed contain no enhancements and are identical to the parts being removed. It is very important that parts obtained from this program be returned to Ford for this study

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.

low performance/lack of acceleration during launch, sluggish vehicle operation and shudder while driving

the vehicle is in DRIVE or REVERSE. The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure steps to replace the torque converter and specified internal transmission components that may have been damaged.

low performance / lack of acceleration during launch, sluggish vehicle operation and shudder while driving.

If the torque converter overheats it can lead to adverse NVH, rough idle, and low performance concerns. Ultimately this will require internal transmission repairs to resolve the concern. Ford Motor Company has developed and update to the Powertrain Control Module software that helps protect the transmission torque converter from overheating when exposed to certain driving styles.

inoperative remote start with a Vehicle Failed To Start message when using the Ford Pass mobile application. This message may be observed even if the vehicle has been driven immediately prior to the remote start request. Other functions such as remote lock and unlock from the Ford Pass mobile application will work as expected. Engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P013A and/or P013C stored in the powertrain control module (PCM). This may be due to an improperly welded exhaust Y-pipe. To correct the condition, follow the Service Procedure to replace the exhaust Y-pipe.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P013A and/or P013C stored in the powertrain control module (PCM). This may be due to an improperly welded exhaust Y-pipe. To correct the condition, follow the Service Procedure to replace the exhaust Y-pipe. Follow the Service Procedure to correct the condition on vehicles that meet all of the following criteria: *2013-2019 Explorer *3.5L Ti-VCT engine *Illuminated MIL with only DTCs P013A and/or P013C

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Use pigtail harness service part numbers 3U2Z-14S411-ZEA or CU2Z-14S411-FA, as both parts are interchangeable. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures.

malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure to replace the MAPT sensor.

malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure to replace the MAPT sensor.

malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure steps to diagnose and replace the MAPT sensor.

drive belt, illuminated charging system indicator, and/or damaged alternator pulley. Accessory drive belt DA8Z-8620-G has been released to eliminate this noise and alternator pulley damage. Refer to Workshop Manual (WSM), Section 303-05 for the removal and installation procedure. For claiming, use causal part 8620 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.

attempting to update the software to version 3.3. Professional Technician Society (PTS) website may show that software version 3.3 is available for 2019 SYNC 3 vehicles. Do not carry out this update as it may lead to a hardware error message. Engineering is investigating, monitor OASIS for updates.

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

turning the ignition on after a remote start event. To temporarily resolve the concern, the heated seat control switch may be cycled off and then back on. Do not attempt any repairs at this time. Engineering is investigating. To assist with the investigation, use the Report a Vehicle Concern link at the bottom of the OASIS report and fill out the form. Monitor OASIS for updates.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

from the right side front interior area while the engine is running. If replacing the DC/AC inverter does not resolve the concern, replace the fuel pump control module with part number FU5Z-9D370-B. Inspect the new replacement module and ensure the engineering part number suffix shows "LA" before installing. If the fuel pump control module has an engineering part number suffix "JA", the part should be returned via the normal part return process. For claiming, use causal part 9D370 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. Engineering is investigating, monitor OASIS for updates.

of satellite radio reception while driving in unobstructed areas. If normal Workshop Manual (WSM) diagnosis and testing does not indicate a fault and no diagnostic trouble codes (DTCs) are stored, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report and complete the form.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

satellite radio reception while driving in unobstructed areas. If normal Workshop Manual (WSM) diagnosis and testing does not indicate a fault and no diagnostic trouble codes (DTCs) are stored, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report and complete the form.

start idle when the customer expects the A/C remain on. The system will return to normal operation after the ignition is turned to the run position. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report to complete the form.

(TiVCT) engine may exhibit an engine vibration and/or the engine mount leaking fluid. A revised engine mount (GB5Z-6038-A) has been released to address this condition. For claiming, use causal part 6038 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.

display a "Hill Descent Control Fault" message in the IPC briefly at start up without any diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.

or after 27-Jun-2017 are equipped with a revised rear lower roll restrictor that eliminates the need for the front roll restrictor. The front roll restrictor has been eliminated by design on these vehicle applications even though the brackets may still be present. Do not add the front roll restrictor to units built after this date, as it may negatively impact the noise, vibration and harshness (NVH) attributes.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the PCM using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

from the right side front interior area while the engine is running. Follow the Service Procedure steps to correct the condition.

or after 27-Jun-2017 are equipped with a revised rear lower roll restrictor that eliminates the need for the front roll restrictor. The front roll restrictor has been eliminated by design on these vehicle applications even though the brackets may still be present. Do not add the front roll restrictor to units built after this date, as it may negatively impact the noise, vibration and harshness (NVH) attributes.

MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.

illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the PCM using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

from the right side front interior area while the engine is running. Follow the Service Procedure steps to correct the condition.

stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump driver module (FPDM) connector. Confirm FPDM connector (F-150 C4336, Expedition/Navigator C433, Transit C433, Explorer C3239) is fully seated prior to performing PC/ED diagnostics or replacing any components. Engineering is investigating, monitor OASIS for updates.

Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

under the headlamps) when the engine is running. Before attempting repairs, verify the frequency type using the Integrated Diagnostic System (IDS) or equivalent. The frequency type in police mode programmable parameters must be set to type 2. The engine must be running for the configuration to complete if this parameter is changed.

Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.

Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.

other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.

every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

may exhibit an Acquiring Signal message with a loss of satellite radio reception while driving in unobstructed areas. Follow the Service Procedure steps to correct the condition.

not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.

exhibit incomplete Ford Telematics service subscription activation, inability to remotely interface with a vehicle, and/or not receiving fleet alerts. Reprogram the TCU using the appropriate Ford scan tool at the latest software level. Fleet vehicle and TCU type can be identified in the Vehicle Information section of OASIS. TCU will be listed as 4G SYNC Connect. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

SYNC/SYNC3 with automatic system updates do not support connecting SYNC to the vehicles internal 4G WI-FI Hotspot if equipped. The SYNC automatic update feature must be connected to an external Wi-Fi source to function properly. No repairs should be made in attempt to correct this concern.

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.

may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.

affected vehicles, the roof rail covers can become loose, which can lead to a visible gap between the cover and roof rail base assembly, rattling, and potential detachment

3M Universal Adhesive Black Part Number 08223, 3M Static Mixing Nozzles Part Number 08193 This program provides a one-time repair for the roof rail covers and retaining clips to 10 years of service or 150,000 miles from the warranty start date of the vehicle, whichever occurs first. This is a one-time repair program. Both roof rail covers should be serviced at time of repair. If a vehicle has already exceeded either the time or mileage limits, this extended warranty coverage will last through June 30, 2021. Coverage is automatically transferred to subsequent owners.

cover and roof rail base assembly, rattling, and potential detachment.

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

The left 2nd row 60 percent seat cushion cover is a different design from the right 2nd row 40 percent cushion cover and the two are not comparable. The right seat trim wraps under the seat and is closed off while the left side is not closed off and may appear loose. This is normal appearance and no repairs should be performed. If the seat foam is exposed, the foam can be tucked upward and the cushion cover refitted to conceal the foam. The seat cushion cover and/or foam should not be replaced for either condition.

2016-2019 Explorer roof rack cap clips are now available as a separate part. It is no longer necessary to order a complete roof rack rail to obtain the cap retainer clips. To correct loose roof rack caps or broken or missing clips, order part number FB5Z-7851050-A. Ensure roof rails are properly torqued to 55 in/lbs (6.2 Nm) and that power tools are not used for installation as over-torqueing may cause warpage and poor fitment.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.

holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.

from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.

EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.

from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

This may be caused by a lack of adhesion of the front door upper moulding to the door. To resolve the condition, follow the Service Procedure steps to reapply adhesive tape to the front door upper moulding. Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria: * 2011-2019 Explorer * Equipped with factory keyless entry keypad * Left side front door upper moulding is loose

Year MKZ Hybrid Vehicles Equipped with the Magnetic Appearance Package - Accelerator Pedal and Brake Pedal Cover Replacement

18-Jun-2018 may exhibit a soft brake pedal and/or long brake pedal travel. Bleed the brake system per Workshop Manual (WSM), Section 206-00. For claiming, use causal part 2552 and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.

exhibit a soft brake pedal and/or long brake pedal travel. Bleed the brake system per Workshop Manual (WSM), Section 206-00. For claiming, use causal part BRAKE and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.

soft brake pedal and/or long brake pedal travel. Bleed the brake system per Workshop Manual (WSM), Section 206-00. For claiming, use causal part BRAKE and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.

display a "Hill Descent Control Fault" message in the IPC briefly at start up without any diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. Reprogram the IPC using the appropriate Ford scan tool or equivalent release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

the RO date of Powertrain Control Module reflash under Customer Satisfaction Program 20B27.

Workshop Manual (WSM), Section 211-02 Power Steering > Diagnosis and Testing has been updated with improved information to aid with accurate noise diagnosis. Replacing the steering gear may not necessarily eliminate the noise concern. Use Chassis Ears on all suspected components to accurately diagnose noise concerns.

Workshop Manual (WSM), Section 211-02 Power Steering > Diagnosis and Testing is in the process of being updated with improved information to aid with accurate noise diagnosis. Replacing the steering gear may not necessarily eliminate the noise concern. Use Chassis Ears on all suspected components to accurately diagnose noise concerns. Monitor OASIS for updates.

The use of unapproved fluid or improper transmission fluid level can lead to reduced vehicle performance and transmission damage that is not covered under warranty. Use only Mercon LV Automatic Transmission Fluid, XT-10-QLVC (US), CXT-10-LV12 (Canada). Use only the Transmission Fluid Exchanger process when performing service intervals. Check and adjust transmission fluid level only at normal operating temperatures of 82?C-93?C (180?F-200?F). The fluid adjustment procedure requires using the appropriate Ford scan tool or equivalent to verify fluid temperature. For optimum performance at high speeds, adjust fluid level to the top of the "MIN" mark on the dipstick.

available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.

Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.

to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints (aka bushings) in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 as an assembly only. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.

to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 assembly. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.

The customer communication requested return of unsold inventory to revise the design similar to the OEM supercession associated with 19V435. We have received no defects associated with the current design.

For customer satisfaction, Hankook is offering pro-rated tire replacement for vehicles with less than 36,000 Miles. This program is managed by Hankook Tire America Corp. and not claimed under Ford new vehicle limited warranty. If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2, contact Hankook Technical Service for possible pro-rated tire replacement. Refer to FMCDealer.com Tire Page for details and Hankook contact information.

If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2 contact Hankook Technical Service for possible pro-rated tire replacement. This may not be the result of improper alignment. For Hankook contact information refer to the Tire Warranty information located on FMCDealer.com.

or missing temperature control switch. The driver and passenger switches are now available separately from the control head. Replacement of the control head assembly is not necessary. The switches are driver and passenger specific and must be installed in the correct location with the red heat indicator facing up. HB5Z-19986-AA - Drivers Side Switch, HB5Z-19986-BA - Passengers Side Switch

Base model vehicles are not equipped with signature lighting and it is not an option. Base level vehicles without the LED lighting surrounding the headlamps are built correctly and should not be modified by installing the signature lamps. Prior to beginning any diagnostics, verify the proper vehicle model/series utilizing OASIS or referring to Workshop Manual Section 100-01.

Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.

vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.