2013 Ford Explorer TSBs

Repair Order (RO) opening date for field service actions 21S32 or 21S43 provided that the RO opening date occurs on or before July 31, 2023. This is a one time repair. In some of the affected vehicles exposed to a corrosive environment where road salt is used during winter months, the rear toe link ball joint located in the rear knuckle could seize. A seized toe link ball joint could wear out and develop a knocking noise after installation of the updated toe links in the FSAs 21S32 or 21S43

If diagnostics lead to a motor replacement, visually inspect the original motor for signs of water intrusion. If found, determine source of water leak prior to replacing the motor. Refer to Workshop Manual (WSM), Section 501-17, Pinpoint Test A for 2011-2016 and Pinpoint Test B for 2017-2022 for identifying the source of the water leak.

Some 2013-2015 Explorer vehicles located in Russia and equipped with a 3.5L Twin independent variable camshaft time (Ti-VCT) EFNGINE, MAY EXHIBIT A HARSH ENGAGEMENT DURING ELEVATED IDLE. tHE CONDITION USUALLY OCCURS WHILE AMBIENT TEMPERATURE IS BELOW -9 c.

Certain States/Provinces Rear Toe Link Ball Joint Inspection This program is a proactive investigation by Ford Motor Company to obtain field data and parts for testing. Ford is voluntarily conducting this program to inspect the toe link ball joint and, if necessary, replace both rear toe links and wheel knuckles on vehicles always registered and always residing in the Nashville (and Calgary) area. The replacement toe links and knuckles being installed contain no enhancements and are identical to the parts being removed. It is very important that any parts obtained from this program be returned to Ford for this study

Certain States/Provinces; Rear Toe Link Ball Joint Inspection This program is a proactive investigation by Ford Motor Company to obtain field data and parts for testing. Ford is voluntarily conducting this program to inspect the toe link ball joint and, if necessary, replace both rear toe links and wheel knuckles on vehicles always registered and always residing in the Nashville, Houston, Miami, Dallas, Atlanta, Phoenix, Winnipeg, and Calgary areas. The replacement toe links and knuckles being installed contain no enhancements and are identical to the parts being removed. It is very important that any parts obtained from this program be returned to Ford for this study.

supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P013A and/or P013C stored in the powertrain control module (PCM). This may be due to an improperly welded exhaust Y-pipe. To correct the condition, follow the Service Procedure to replace the exhaust Y-pipe.

To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P013A and/or P013C stored in the powertrain control module (PCM). This may be due to an improperly welded exhaust Y-pipe. To correct the condition, follow the Service Procedure to replace the exhaust Y-pipe. Follow the Service Procedure to correct the condition on vehicles that meet all of the following criteria: *2013-2019 Explorer *3.5L Ti-VCT engine *Illuminated MIL with only DTCs P013A and/or P013C

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Use pigtail harness service part numbers 3U2Z-14S411-ZEA or CU2Z-14S411-FA, as both parts are interchangeable. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures.

This may be due to various conditions in the window motor including excessive drive gear backlash, bushing wear, and/or excessive end play. To resolve the condition, follow the Service Procedure steps to replace the window motor, window motor connector, window regulator, upper glass run, and door glass.

Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.

Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.

Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.

steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.

(TiVCT) engine may exhibit an engine vibration and/or the engine mount leaking fluid. A revised engine mount (GB5Z-6038-A) has been released to address this condition. For claiming, use causal part 6038 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.

equipped with AWD and built on or before 30-Jun-2016 may exhibit a propane or natural gas odor during idle or low speed driving. This may be due to break down of the power transfer unit (PTU) fluid caused by excessive heat. If the source of the odor is identified as originating from the PTU, an idler bearing repair kit is available to repair the PTU. Refer to the Workshop Manual (WSM), Section 308-07. If the PTU is determined to be repairable, utilize kit GB5Z-7P258-A and the included instruction sheet. For claiming use causal part 7P258 and applicable labor operations in section 07 of the Service Labor Time Standards (SLTS) Manual.

3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) that is being repaired or replaced for an internal failure must also have the vent hose replaced due to contamination in the hose.

(AWD) AND BUILT ON OR BEFORE 30-JUN-2016 MAY EXHIBIT A TICKING AND/OR KNOCKING NOISE COMING FROM THE DRIVELINE AREA. TO IDENTIFY THIS NOISE, REFER TO WORKSHOP MANUAL (WSM), SECTION 100-04, AND FOLLOW THE SYMPTOM CHART. IF THE SOURCE OF THE NOISE IS IDENTIFIED AS THE PTU AND/OR INTERNAL TO THE PTU, DISASSEMBLE PTU ASSEMBLY. REFER TO UPDATED WSM, SECTION 308-07. IF THE PTU IS DETERMINED TO BE REPAIRABLE, UTILIZE KIT GB5Z-7P258-A AND THE INCLUDED INSTRUCTION SHEET. FOR CLAIMING, USE CAUSAL PART 7P258 AND APPLICABLE LABOR OPERATIONS IN SECTION 07 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

located in Russia and equipped with a 3.5L Twin independent Variable Camshaft Timing (Ti-VCT) engine, may exhibit a harsh engagement during elevated idle. The condition usually occurs while ambient temperature is below -9C. ACTION Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 99.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

2013-2016 Fusion, MKZ, 2013-2015 Explorer, 2013-2014 Focus ST and Edge vehicles equipped with 2.0L EcoBoost engines may exhibit fuel odor originating from the positive crankcase ventilation (PCV) hose. SERVICE PROCEDURE 1. Is the vehicle a 2016 Escape or MKC? a. Yes - check the vehicle build date. Was the vehicle built on or before 12/15/2015? (1) Yes - proceed to Step 2. (2) No - this article does not apply. b. No - proceed to Step 2. 2. Inspect the PCV hose to make sure it is properly connected to the valve cover and the low pressure intake duct. a. For Escape and Focus ST vehicles remove the cowl panel grille to access the hose. Refer to Workshop Manual (WSM), Section 501-02. b. For Edge vehicles remove the air cleaner outlet pipe to access the hose. Refer to WSM, Section 303-12. 3. Does the PCV hose exhibit a fuel smell or was the hose disconnected? a. Yes - replace hose and reassemble the vehicle. b. No - Refer to WSM, Section 303-13 for normal diagnosis.

HESITATION DUE TO POSSIBLE HYDRAULIC CIRCUIT DRAIN. MODEL 2013-16 VARIOUS VEHICLES. *PE

THE FRONT WINDOW REGULATOR MOTOR NEEDS TO BE REPLACED. *LJ

ENGINES BUILT BEFORE 10/05/2014 MAY HAVE LACK OF POWER AND MALFUNCTION ILLUMINATED LAMP CODE DUE TO AMBIENT TEMPERATURES BELOW 0 DEGREES CELSIUS. *LJ

AND/OR CONSUMPTION OF OIL, FROM TAIL PIPE, DURING NORMAL ENGINE TEMPERATURE OPERATION. MODEL 2010-2014 FLEX, TAURUS, EXPLORER, MKS, MKT. *PE

MODEL 2012-2014 FLEX, TAURUS, EXPLORER, MKT. *PE

AIR CONDITIONING (HVAC) MODULE, AN INABILITY TO COMMUNICATE, DURING REPAIR DIAGNOSIS. MODEL 2013-2014 EXPLORER, TAURUS. *PE

*LJ

CRANKCASE VENTILATION (PCV) SYSTEM, MAY HAVE ENGINE OIL IN INTAKE AIR SYSTEM COMPONENTS. MODEL 2011-2013 EDGE, EXPLORER, MKX, 2013 TAURUS, MKS, MKT, FLEX. *PE

OF IDLE RPM, DIFFICULT IN STARTING, LACK OF POWER, RUNNING ROUGH AND CRANK NO START SITUATION. MODEL 2013-2014 TAURUS, EDGE, EXPLORER, 2013-2014 MKT. *PE

BAFFLE MIGRATING THROUGH FRESH AIR INTAKE OF POSITIVE CRANKCASE VENTILATION (PCV) SYSTEM. MODELS 2011-2013 EDGE, EXPLORER, MKX, TAURUS, MKS, MKT, FLEX. *PE

It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.

This may be the result of the ribbon cables not being fully seated inside the front display interface module (FDIM) or an improper software configuration of the FDIM.

replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

or before 15-Aug-2013 may exhibit a door ajar lamp illuminated with all doors closed. This may be due to the door ajar sensor within the door latch. Follow the Service Procedure steps to correct the condition.

or before 15-Aug-2013 may exhibit a door ajar lamp illuminated with all doors closed. This may be due to the door ajar sensor within the door latch. Follow the Service Procedure steps to correct the condition.

This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

PROPERLY AND PASSES NETWORK TEST BUT FAILS ON DEMAND SELF TEST. MODEL 2011-15 FUSION F-150, EXPLORER, TAURUS, SUPER DUTY, MKZ, MKC, MKS, MKT, MKX. *PE

TOUCH) VEHICLES WILL DEFAULT TO ICE BLUE AFTER THE IGNITION SWITCH CYCLE. *PE

WOULD FAIL, AFTER VEHICLE HAS BEEN STARTED. MODEL 2013-14 EDGE, EXPLORER, F150, MKX. *PE

WILL BE ILLUMINATED AND THE POWERTRAIN CONTROL MODULE (PCM) WOULD BE REPROGRAM WITH LATEST CALIBRATION. MODEL 2013-2014 POLICE EXPLORER, TAURUS, MKT LIVERY, MKS. *PE

IMPROVED COOLING FAN CIRCUIT DUE TO A LACK OF AIR CONDITIONING, A MALFUNCTIONING INDICATOR LAMP (MIL) AND OVERHEATING. *PE

WHICH LEADS TO CARBON CANISTER SATURATED WITH LIQUID FUEL AND A FUEL ODOR, SLOW FILL, OR HESITATION OR STUMBLE, OCCURS WHILE DRIVING. MODEL 2013 EXPLORER, TAURUS, MKS, FLEX, MKT, FUSION, MKZ, POLICE INTERCEPTOR, AND SEDAN. *PE

CYCLE, OR SLOW NAVIGATION CALCULATIONS, DUE TO AMOUNT OF DATA, WITHIN SIZE OF CONTACT LIST, CREATING PROCESSING PROBLEM FOR MODULE DURING KEY ON CYCLE. MODELS 2011-2013. NO MODEL LISTED. *PE

SYMPTOMS AS DISCHARGED IKT BATTERY. MODELS 2012-2013 F-150, F SUPER DUTY, EXPEDITION, NAVIGATOR, FLEX, EDGE, EXPLORER, TAURUS, MUSTANG. *PE

INTERFACE MODULE (FDIM), TOUCHSCREEN CALIBRATION MUST BE PERFORMED. MODEL YEARS 2011-2013. NO MODELS LISTED. *PE

INFORMATION REGARDING EXTENDED WARRANTY FOR COVERING ACCESSORY PROTOCOL INTERFACE MODULE REGARDLESS OF MILEAGE. MODELS 2011-2013 EDGE, EXPLORER, MKX, FOCUS, ESCAPE, FLEX, FUSION, TAURUS, MKS, MKT, MKZ, F-150, F-SUPER DUTY. *PE

Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

and MKT Vehicles Left Front Door Latch Extended Coverage

This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.

appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.

Follow the Service Procedure steps to correct the condition.

PLEASE USE AT YOUR DISCRETION. VARIOUS 2010-2015 VEHICLES MAY EXPERIENCE A TURBULENCE NOISE, SIMILAR TO AN HELICOPTER NOISE, AT HIGHWAY SPEEDS WHEN THE REAR DOOR WINDOW(S) OR SUNROOF ARE OPEN. *TA

MODEL 2011-13 EDGE, EXPLORER, FLEX, MKX, MKT. *PE

MODEL 2011-2013 EDGE, FLEX, EXPLORER, MKX, MKT. *PE

MODEL 2011-2013 EDGE, EXPLORER, FLEX, MKX, MKT. *PE

MODELS 2011-2013 EXPLORER. *PE

MODELS 2013 TAURUS, EXPLORER. *PE

Certain 2017 Model Year Continental Livery Vehicles - Exterior Door Handle Replacement

As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.

MODEL 2011-15 EXPLORER. *PE

MODEL 2011-15 EXPLORER. *PE

THE FUEL PUMP TO BE INOPERATIVE. MODEL 2013 EXPLORER. *PE

backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

The use of unapproved fluid or improper transmission fluid level can lead to reduced vehicle performance and transmission damage that is not covered under warranty. Use only Mercon LV Automatic Transmission Fluid, XT-10-QLVC (US), CXT-10-LV12 (Canada). Use only the Transmission Fluid Exchanger process when performing service intervals. Check and adjust transmission fluid level only at normal operating temperatures of 82?C-93?C (180?F-200?F). The fluid adjustment procedure requires using the appropriate Ford scan tool or equivalent to verify fluid temperature. For optimum performance at high speeds, adjust fluid level to the top of the "MIN" mark on the dipstick.

Escape, 2009-2011 Mariner, 2010-2014 Fusion, 2010-2011 Milan, 2012-2014 Edge/Explorer, and 2013-2014 Taurus/MKT/MKZ vehicles built on or before 10/14/2013 and equipped with a 6F35 automatic transmission may exhibit a fluid leak from the left hand (LH) transmission halfshaft seal due to wear on the transmission case bushing.

*CN

MODEL 2013-2014 ESCAPE, FUSION, EDGE, EXPLORER, TAURUS, MKT, MKZ. *PE

(MIL) WILL ILLUMINATE WITHOUT ANY OTHER SYMPTOMS PRESENT AND MAY BE CAUSED BY TORN INNER TORQUE CONVERTER SEAL. MODEL 2013 EDGE, FLEX, TAURUS, EXPLORER, MKS, MKT. *PE

EXPERIENCE A LEAKAGE OF FLUID FROM LEFT HAND (LH) HALFSHAFT SEAL. MODEL 2013 ESCAPE, FUSION, EDGE, EXPLORER, TAURUS, MKT, MKZ. *PE

UPSHIFTS FROM 3RD, 4TH OR 5TH GEAR WHEN TEMPERATURE IS BELOW 21 DEGREES CELSIUS (70 DEGREES FAHRENHEIT) FOR TRANSMISSION FLUID. MODEL 2013 EXPLORER. *PE

NOISE IS HEARD LIKE POP, TING, CLICK, COMING FROM FRONT WHEEL AREA. MODELS 2011-2013 TAURUS, EXPLORER, FLEX, MKS, MKT. *PE

THE CENTER SUPPORT BEARING HEAT SHIELD(7F469). THE HEAT SHIELD CAN BE DISCARDED.

MKS, MKX, AND 2013-2014 LINCOLN MKT VEHICLES MAY EXPERIENCE PROBLEMS WITH THE CRUISE CONTROL SPEED THAT DOESN'T MATCH THE SPEEDOMETER SPEED. *TA

SEATS WHEN MOVING BACKWARDS OR FORWARD. MODEL 2009-2015 F-150, TAURUS, FLEX, MKT, MKS, F-SUPER DUTY, EXPLORER. *PE

SLUDGING OF PTU LUBE, RESULTING IN AN INCREASED INTERNAL LUBE TEMPERATURE. MODEL 2011-2014 EXPLORER, TAURUS SHO. *PE

MODEL 2013 TAURUS, EXPLORER, MKS. *PE

Inspection/Replacement Under Safety Recall 21S43, some of the affected vehicles that have had one (or both) rear wheel knuckle(s) replaced and were sold or operated in certain traditional corrosion areas where road salt is used extensively during winter months, may experience a seized toe link ball joint resulting in a fracture of the outboard section of the rear suspension toe link

affected vehicles exposed to a highly corrosive environment where road salt is used extensively during winter months, have experienced a seized toe link ball joint resulting in a fracture of the outboard section of the rear suspension toe link.

to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints (aka bushings) in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 as an assembly only. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.

to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 assembly. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.

The customer communication requested return of unsold inventory to revise the design similar to the OEM supercession associated with 19V435. We have received no defects associated with the current design.

MODEL 2013 ESCAPE, FUSION, EDGE, TAURUS, EXPLORER, MKT, MKZ. *PE

systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

This may be caused by a lack of adhesion of the front door upper moulding to the door. To resolve the condition, follow the Service Procedure steps to reapply adhesive tape to the front door upper moulding. Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria: * 2011-2019 Explorer * Equipped with factory keyless entry keypad * Left side front door upper moulding is loose

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

BROKEN AND ITS HARD TO OPEN OR CLOSE. MODEL 2009-14 MKS, 2011-15 EXPLORER, 2013-14 ESCAPE. *PE

CONDITION AND NEED TO BE CHECKED FOR DEBRIS AND/OR CORROSION. MODEL 2011-2014 EXPLORER, FLEX, TAURUS, EDGE, MKX, MKT, MKS. *PE

CODE (DTC) ACCOMPANYING IT, IN THE ANTI-LOCK BRAKE SYSTEM (ABS) MODULE OR TERRAIN CONTROL MODULE. MODEL 2011-2014 EXPLORER. *PE

original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

INOPERATIVE, LACK OF OR SLOW RESPONSE TO PHONE AND VOICE BUTTON OPERATION. MODELS 2012-2013 FOCUS, E-SERIES, EDGE, EXPEDITION, FUSION, EXPLORER, F-150, F-250, NAVIGATOR, 2013-2014 FLEX, 2012-2014 FIESTA, MUSTANG, 2013 ESCAPE, C-MAX, TAURUS, 2012 MKZ. *PE

DISPLAY A MESSAGE UPON INITIAL KEY CYCLE. MODEL YEARS 2013-2014. NO MODELS LISTED. *PE

Terms: added 21R01 and 21R02 REASON FOR PROVIDING A NO-COST, ONE-TIME REPAIR: added 21R01 and 21R02 OWNER NOTIFICATION MAILING SCHEDULE: added mailing schedule for 21R01 and 21R02 OASIS ACTIVATION: added 21R01 and 21R02

vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.

THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.

MODEL 2014-15 FUSION, 2011-15 MKX, 2013-15 SUPER DUTY, EXPLORER, TAURUS, MKS, MKT, 2015 F-150, MKZ, MKC, 2011-15 MKX. *PE

exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.

CUSTOMERS MAY INDICATE THE ODOR SMELLS LIKE SULFUR, OR THAT EXHAUST ODORS ARE ENTERING THE VEHICLE CABIN. THIS CONDITION MAY BE WORSENED WHEN THE CLIMATE CONTROL SYSTEM IS IN RECIRCULATE MODE AND THE VEHICLE IS HEAVILY ACCELERATED FOR AN EXTENDED PERIOD. WHETHER AND TO WHAT EXTENT ANY CUSTOMER OR OCCUPANT OF A 2011-2015 EXPLORER VEHICLE EXPERIENCES THE EXHAUST ODOR WILL BE AFFECTED BY DRIVING HABITS, WEATHER AND INDIVIDUAL SENSITIVITIES.

CUSTOMERS MAY INDICATE THE ODOR SMELLS LIKE SULFUR, OR THAT EXHAUST ODORS ARE ENTERING THE VEHICLE CABIN. THIS CONDITION MAY BE WORSENED WHEN THE CLIMATE CONTROL SYSTEM IS IN RECIRCULATE MODE AND THE VEHICLE IS HEAVILY ACCELERATED FOR AN EXTENDED PERIOD. WHETHER AND TO WHAT EXTENT ANY CUSTOMER OR OCCUPANT OF A 2011-2015 EXPLORER VEHICLE EXPERIENCES THE EXHAUST ODOR WILL BE AFFECTED BY DRIVING HABITS, WEATHER AND INDIVIDUAL SENSITIVITIES. FOLLOW EACH AND EVERY STEP OF THE TSB SERVICE PROCEDURE IN PROCEDURE 1 TO IMPROVE THE CONDITION.

THIS MAY BE CAUSED BY THE SEAT CUSHION COVER J-RETAINER BECOMING DISENGAGED FROM THE SEAT CUSHION PAN FLANGE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.

MODEL 2013-2014 ESCAPE, 2013 EXPLORER, F150. *PE

A SOFTWARE UPGRADE IS AVAILABLE FOR CERTAIN VEHICLES. MODELS 2012-2013 EDGE, EXPLORER, MKX, FOCUS, ESCAPE, FLEX, FUSION, TAURUS, MKS, MKT, F-150. *PE UPDATED 5/10/13. *PE UPDATED 9/17/13. *PE