2012 Chrysler 300 TSBs

this is normal and not a defect.

this is normal and not a defect.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

semi and full synthetic oils.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands; DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Hands Free Module (and associated components) are the systems responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Left and right outlet temperatures do not match when system is in "sync" . Occupants will experience being cold ( winter time), on either passenger or driver side, even though the temperature setting is the same. Root cause: Suspect sun senors ( PN 55111274AA and 55111275AA). THERE WILL BE NO DTC FOR THE SUN SENSOR active or stored. The issue is diagnosed by using an INCANDESCENT (not LED) shop lamp. Shine the shop lamp on the left side of the sensor, then on the right side of the sensor, while monitoring sensor output with STARSCAN. The reading should change from 0 (or near zero) to about 20 to 40. The important thing is that the left and right readings are the same, and that they change when the lamp is shone on it.

The technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1632-15 - Left High Beam Control-Circuit Short To Battery Or Open. B1636-11 - Right High Beam Control-Circuit Short To Ground. In addition the customer may describe the following:High beam headlamps flicker in cold weather. High beams lamps not working properly in cold weather.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

A customer may experience that the Navigation radio locks up, and both of the navigation voice and display stops working. The user will be locked out of all navigation functions.Replacing the Telematics Gateway Module (TGM/TGW) will repair this condition.All radio and navigation functions are controlled by the TGM.

The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.

may cause an intermittent airbag warning light.

The technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1632-15 - Left High Beam Control-Circuit Short To Battery Or Open. B1636-11 - Right High Beam Control-Circuit Short To Ground. In addition the customer may describe the following:High beam headlamps flicker in cold weather. High beams lamps not working properly in cold weather.

vehicle indicator drifting from the given route and/or navigation resets. To fix this customer issue, the following must be performed in accordance to TSB 08-004-13:~ 1) Replace radio 05064543ZG or 05091385ZC with P/N 05091462ZE (for non- Russian market) or 05091463ZG (Russian market) respectively.~ 2) Replace the amplifier with the appropriate parts are shown as below:~ Replace 05064981AA-AJ with 05064981AK~ Replace 05064982AA-AL with 05064982AM~ Replace 68040979AA-AE with 68040979AF~ Replace 05064947AA-AK with 05064947AL~ 3) Reflash the HVAC module.~

vehicle indicator drifting from the given route and/or navigation resets. To fix this customer issue, the following must be performed in accordance to TSB 08-004-13:~ 1) Replace radio 05064543ZG or 05091385ZC with P/N 05091462ZE (for non- Russian market) or 05091463ZG (Russian market) respectively.~ 2) Replace the amplifier with the appropriate parts are shown as below:~ Replace 05064981AA-AJ with 05064981AK~ Replace 05064982AA-AL with 05064982AM~ Replace 68040979AA-AE with 68040979AF~ Replace 05064947AA-AK with 05064947AL~ 3) Reflash the HVAC module.~ Please Refer TSB 08-004-13 for additional Informations.~ Issue 2~ 1. In the Network Topology view of wiTECH, determine if the Amplifier is communicating on the CAN bus by noting the color of the amplifier icon. (blue = present, red = not communicating ) ~ 2. Is the Amplifier present (blue) on the CAN bus?~ a. Yes >> This Tech Tip does not apply. Further diagnostics may be required.~ b. No >> Please Reference TSB #08-032-12. This bulletin involved re-flashing the Amplifier with updated software.

equipped) and updating the Heating, Ventilation and Air Conditioning (HVAC) module. A customer may experience one or all of the following: Navigation system will reset. Navigation will display incorrect routing. Vehicle indicator on the screen will drift from the given route.

The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.

may cause an intermittent airbag warning light.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Customers may experience a Malfunction Indicator Lamp (MIL)illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: U0197-00 - Lost Communication With Hands Free Phone Module. Customers may also comment one or more the following: Loss of audio while on a Bluetooth phone call(MYs 2014 - 2019 JC Only). HFM does not boot properly. "Hands-Free Module Loading" is displayed on the head unit. The HFM is inoperative and unresponsive to all user input. The HFM is unresponsive and appears off the bus to wiTECH. Inaccurate foreign language translations. Voice Recognition (VR) is sluggish after changing the language. IPhone 4 starts auto recording itself. Background noise from automated speech recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show ?Musicpaused connecting phone? while a song is being played and without an incoming call. Wrong BTSA screen when deleting. When in Text To Speech (TTS), it will be a mix of the TTS and recording. IPod touch, BTSA will not audio stream. Integrated center stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition was turned off. Automatic Sound Recognition (ASR) microphone picking up background noise. When the language is set for Italian and after the ignition is cycled,the phone screens will change to English(Sales Code RSQ Only). No response from the steering wheel VR button. Not being able to enter into the phone screen on the radio. The customer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English. The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

A small number of customers may report no start condition with the Vehicle Security Light flashing and the DTC B1A8A-00 ? MULTI-MODULE VIN HANDSHAKE FAILURE ? active.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

A customer may experience that the Navigation radio locks up, and both of the navigation voice and display stops working. The user will be locked out of all navigation functions.Replacing the Telematics Gateway Module (TGM/TGW) will repair this condition.All radio and navigation functions are controlled by the TGM.

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

A customer may experience that the Navigation radio locks up, and both of the navigation voice and display stops working. The user will be locked out of all navigation functions.Replacing the Telematics Gateway Module (TGM/TGW) will repair this condition.All radio and navigation functions are controlled by the TGM.

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

service flash of the Hands Free Module (HFM). The customer may note when trying to select a none supported language like Russian or Portuguese the Hands Free screen will default to English. The Voice Recognition (VR) will default back to the last language (Italian, French, Spanish, German or Dutch) the customer was using. After the software updated has been completed both the Hands Free screen and VR will default back to the last language used. VR Teleprompter enhancement.

The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.

have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.

A customer may experience that the Navigation radio locks up, and both of the navigation voice and display stops working. The user will be locked out of all navigation functions.Replacing the Telematics Gateway Module (TGM/TGW) will repair this condition.All radio and navigation functions are controlled by the TGM.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) are the systems responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

The customer may experience the following:HFM does not boot properly. "Hands-Free Module Loading" displayedon the head unit.TheHFM is inoperative and unresponsive to all user input.TheHFM is unresponsive and appears off the bus to wiTECH.Inaccurate foreign language translations.VoiceRecognition (VR) is sluggish after changing the language.IPhone4 starts auto recording itself.Backgroundnoise from Automated Speech Recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show?Music paused connecting phone? while a song is beingplayed and without an incoming call. Wrong BTSA screen when deleting. Whenin Text To Speech (TTS), it will be a mix of the TTS and recording. IPodtouch, BTSA will not Audio Stream.Integratedcenter stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition wasturned off.AutomaticSound Recognition (ASR) Microphone picking up background noise.WithSales code RSQ, when the language is set for Italian and after theignition is cycled, the phone screens will change to English.No response from the VR button on the steering wheel.Notbeing able to enter into the phone screen on the radio.Technicians may find Diagnostic Trouble Code (DTC) U0197-00 Lost CommunicationWith Hands Free Phone Module, is set. Thecustomer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English.The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.After the software update has been completed, both the hands free screen and VR will default back to the last language used.Enhancements now include all vehicles, not just internationalvehicles.The following software enhancement isincluded:VR Teleprompter

BULLETIN ON SELECTIVELY ERASING AND REPROGRAMMING POWERTRAIN CONTROL MODULE *CN

AND EFFICIENT MANNER FOR HANDS FREE MODULE (HFM). *PE

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.

engines, please note that there is a new diagnostic procedure available in DealerCONNECT for P-codes in relationship to cam phasers. Please use this new information for trouble shooting of cam phasers and oil control valves for MIL on issues.

(248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

installed in the vehicle.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

If the pins are missing request to add the dowel pin first and then install the transmission

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

If the pins are missing request to add the dowel pin first and then install the transmission

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module. ? U0401 - Implausible Data Received From ECM/PCM. ? P0441 - Evap Purge System Performance. ? P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. This software update also has improvements for fuel pump relay cycling during remote starts.

Control Module (PCM) with new software. The customer may describe hearing the fuel pump relay cycling during remote start or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: ? U0140 - Lost Communication With Body Control Module (BCM). ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. ? P0522 - Engine Oil Pressure Sensor Circuit Low. ? P0108 - Manifold Absolute Pressure Sensor Circuit High. ? P1239 - Engine Oil Temperature Too Low. ? P0298 - Engine Oil Temperature Too High.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs) have been set: ? U0401-00 - Implausible Data Received From ECM/PCM ? P0441 - Evap Purge System Performance ? P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1 This software update also has improvements for fuel pump relay cycling during remote starts.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

DUE TO AN ENGINE FRACTURED TIMING CHAIN GUIDE, THE TIMING CHAIN IN ENGINE WILL BREAK AND WOULD RESULT IN SEVERE DAMAGE TO THE ENGINE. MODEL 2009-2012 CHALLENGER, CHARGER, 300. *PE

INTERNAL TEMPERATURE TOO HIGH DIAGNOSTIC FAULT CAUSES PERMANENT MALFUNCTION INDICATOR LAMP (MIL) TO ILLUMINATE DUE TO INADVERTENTLY PROGRAMMING SOFTWARE TO NOT RUN POSITION VALVE STUCK DIAGNOSTICS OR PERMANENTLY SET INTERNAL TEMPERATURE. MODEL 2012 CHARGER, 300. *PE

IN MANUAL (USER GUIDE), STATED INCORRECTLY ENGINE OIL (SAE 5W-40), INSTEAD OF CORRECTLY ENGINE OIL (SAE 0W-40 FULL SYNTHETIC ENGINE OIL. *PE

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Please repaint to color match vehicle.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

the rear spoiler and if necessary correcting any paint damage and installing spoiler tape to prevent spoiler to paint surface contact. The customer may notice paint chipping on the deck lid at the rear spoiler

Incorrect right and left rear door trim panel.

Right and/or left rear door contacts inner quarter panel.

DTC B1632-11 And B1636-11 Set

DTC B1632-11 And B1636-11 Set

DTC B1632-11 And B1636-11 Set

industry awareness regarding the recommended usage of Authentic Mopar Glass.

the rear spoiler and if necessary correcting any paint damage and installing spoiler tape to prevent spoiler to paint surface contact. The customer may notice paint chipping on the deck lid at the rear spoiler

the rear spoiler and if necessary correcting any paint damage and installing spoiler tape to prevent spoiler to paint surface contact. The customer may notice paint chipping on the deck lid at the rear spoiler

involves lowering the roof headliner and inserting a spacer. .1 - Low Spot2 - Area Of Concern

Incorrect right and left rear door trim panel.

Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.

stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

the rear spoiler and if necessary correcting any paint damage and installing spoiler tape to prevent spoiler to paint surface contact. The customer may notice paint chipping on the deck lid at the rear spoiler

Incorrect right and left rear door trim panel.

*KB

Print I-Sheet for technician use.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

Powertrain Control Module (PCM) with new software to eliminate the potential of setting this erroneous Diagnostic Trouble Code. Technician may find that the following erroneous Diagnostic Trouble Code has been set: P0573 - Brake Switch 1 Stuck Off

The customer may experience up to 1mm(1/32?) fore/aft movement of the driver and/or passenger seat during acceleration and/or braking.

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

Powertrain Control Module (PCM) with new software to eliminate the potential of setting this erroneous Diagnostic Trouble Code. Technician may find that the following erroneous Diagnostic Trouble Code has been set: P0573 - Brake Switch 1 Stuck Off

The customer may experience up to 1mm(1/32?) fore/aft movement of the driver and/or passenger seat during acceleration and/or braking.

the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set in the PCM memory: ? U0140 - Lost Communication With Body Control Module (BCM) (Attempting to clear this DTC will be unsuccessful). ? P0573 - Brake Switch 1 Stuck Off.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

Powertrain Control Module (PCM) with new software to eliminate the potential of setting this erroneous Diagnostic Trouble Code. Technician may find that the following erroneous Diagnostic Trouble Code has been set: P0573 - Brake Switch 1 Stuck Off

*KB

To fix this customer issue, the following must be performed in accordance to TSB 08-004-13:~

To fix this customer issue, the following must be performed in accordance to TSB 08-004-13.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.

To fix this customer issue, the following must be performed in accordance to TSB 08-004-13:~

To fix this customer issue, the following must be performed in accordance to TSB 08-004-13.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.

modification or replacement of the backlite rear shelf. The customer may describe a rattle or buzz noise coming from the rear of the vehicle with the radio on or while driving on bumpy roads. This may be caused by the rear shelf moving relative to the backlite.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus. Flashing the amplifier will correct this condition.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.

equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: Phone screen buttons intermittently missing. Rear view camera screen may be blank. Improved rear view camera image. Radio presets and parameters returning to defaults. AM or FM audio mutes upon start up. Seek frozen, tuner locks up, unable to change stations (RE3 only). Radio resets (RE3 only). Presets are intermittently skipped (RE3 only). When playing MP3, iPod or USB songs, the screen will not always display the correct song title. Sirius Traffic/Weather Jump button improvement. Controls Screen popup time-out option has been added to settings screen (SRT only). Temperature and Oil pressure gauge enhancements (SRT only). Blind spot monitor chime enhancement. Radio Language Translation improvements. Navigation Language Translation improvements. Disable/Enable traffic announcement feature added (RB4 RB5 RB6). Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). Garmin audio enhancements (RB4 RB5 RB6). Navigation map enhancements (RB4 RB5 RB6). Garmin stuck on loading screen (RB4 RB5 RB6). Traffic rerouting and icon enhancements (RB4 RB5 RB6). Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). Radio may reboot when Russian language keyboard used (RB4). Travel Link showing up as unsubscribed. Fuel Station routing issues. Heated seat greyed out. Navigation icon going backwards.

The EGR hose may weep coolant.

The EGR hose may weep coolant.

equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: ? Improve FM radio reception. (This only applies to 2012 LX vehicles with RE6, RB6 radios located in Dubai). ? Audio muted after a cold start. This applies to all 2011 vehicles and only 2012 vehicles with software level earlier then 11.43.37. ? Phone screen buttons intermittently missing. ? Rear view camera screen may be blank. ? Improved rear view camera image. ? Radio presets and parameters returning to defaults. ? AM or FM audio mutes upon start up. ? Seek frozen, tuner locks up, unable to change stations (RE3 only). ? Radio resets (RE3 only). ? Presets are intermittently skipped (RE3 only). ? When playing MP3, iPod or USB songs, the screen will not always display the correct song title. ? Sirius Traffic/Weather Jump button improvement. ? Controls Screen popup time-out option has been added to settings screen (SRT only). ? Temperature and Oil pressure gauge enhancements (SRT only). ? Blind spot monitor chime enhancement. ? Radio Language Translation improvements. ? Navigation Language Translation improvements. ? Disable/Enable traffic announcement feature added (RB4 RB5 RB6). ? Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). ? Garmin audio enhancements (RB4 RB5 RB6). ? Navigation map enhancements (RB4 RB5 RB6). ? Garmin stuck on loading screen (RB4 RB5 RB6). ? Traffic rerouting and icon enhancements (RB4 RB5 RB6). ? Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). ? Radio may reboot when Russian language keyboard used (RB4). ? Travel Link showing up as unsubscribed. ? Fuel Station routing issues. ? Heated seat greyed out. ? Navigation icon going backwards.

equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: ? Audio muted after a cold start. This applies to all 2011 vehicles and only 2012 vehicles with software level earlier then 11.43.37. ? Phone screen buttons intermittently missing. ? Rear view camera screen may be blank. ? Improved rear view camera image. ? Radio presets and parameters returning to defaults. ? AM or FM audio mutes upon start up. ? Seek frozen, tuner locks up, unable to change stations (RE3 only). ? Radio resets (RE3 only). ? Presets are intermittently skipped (RE3 only). ? When playing MP3, iPod or USB songs, the screen will not always display the correct song title. ? Sirius Traffic/Weather Jump button improvement. ? Controls Screen popup time-out option has been added to settings screen (SRT only). ? Temperature and Oil pressure gauge enhancements (SRT only). ? Blind spot monitor chime enhancement. ? Radio Language Translation improvements. ? Navigation Language Translation improvements. ? Disable/Enable traffic announcement feature added (RB4 RB5 RB6). ? Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). ? Garmin audio enhancements (RB4 RB5 RB6). ? Navigation map enhancements (RB4 RB5 RB6). ? Garmin stuck on loading screen (RB4 RB5 RB6). ? Traffic rerouting and icon enhancements (RB4 RB5 RB6). ? Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). ? Radio may reboot when Russian language keyboard used (RB4). ? Travel Link showing up as unsubscribed. ? Fuel Station routing issues. ? Heated seat greyed out. ? Navigation icon going backwards.

equipped with navigation (RB4, RB5 and RB6) the navigation software will also be updated. The customer may experience one or more of the following conditions: Phone screen buttons intermittently missing. Rear view camera screen may be blank. Improved rear view camera image. Radio presets and parameters returning to defaults. AM or FM audio mutes upon start up. Seek frozen, tuner locks up, unable to change stations (RE3 only). Radio resets (RE3 only). Presets are intermittently skipped (RE3 only). When playing MP3, iPod or USB songs, the screen will not always display the correct song title. Sirius Traffic/Weather Jump button improvement. Controls Screen popup time-out option has been added to settings screen (SRT only). Temperature and Oil pressure gauge enhancements (SRT only). Blind spot monitor chime enhancement. Radio Language Translation improvements. Navigation Language Translation improvements. Disable/Enable traffic announcement feature added (RB4 RB5 RB6). Garmin Voice Recognition (VR) enhancements (RB4 RB5 RB6). Garmin audio enhancements (RB4 RB5 RB6). Navigation map enhancements (RB4 RB5 RB6). Garmin stuck on loading screen (RB4 RB5 RB6). Traffic rerouting and icon enhancements (RB4 RB5 RB6). Incorrect map graphics on traffic circle (RB4 RB6 Right Hand Drive). Radio may reboot when Russian language keyboard used (RB4). Travel Link showing up as unsubscribed. Fuel Station routing issues. Heated seat greyed out. Navigation icon going backwards.

A customer may experience one or move of the following: ? Fuel Station Routing issues. ? Heated Seat Greyed Out. ? Navigation Icon going backwards. ? Map Checksum Error.

OUT HEATED SEAT, BACKWARDS GOING NAVIGATION ICON, ROUTING ISSUES WITH FUEL STATION, ETC. MODEL 2011-12 CHARGER, 300, JOURNEY. *PE

There is no cap on the end of the vent hose. This is intentional. Some graphics in StarParts may show a vent hose including a cap, but this is incorrect. The actual production vent hose has an open elbow fitting, not a cap. The elbow should be pointing downwards in the vehicle.~

Customers may indicate that the MIL is illuminated and/or the transmission went into limp-in. Upon further investigation, Diagnostic Trouble Code (DTC) P0730 - Incorrect Gear Ratio is either active or stored in the PCM?s memory.

Customers may indicate that the MIL is illuminated and/or the transmission went into limp-in. Upon further investigation, Diagnostic Trouble Code (DTC) P0730 - Incorrect Gear Ratio is either active or stored in the PCM?s memory.

There is no cap on the end of the vent hose. This is intentional. Some graphics in StarParts may show a vent hose including a cap, but this is incorrect. The actual production vent hose has an open elbow fitting, not a cap. The elbow should be pointing downwards in the vehicle.~

Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

There is no cap on the end of the vent hose. This is intentional. Some graphics in StarParts may show a vent hose including a cap, but this is incorrect. The actual production vent hose has an open elbow fitting, not a cap. The elbow should be pointing downwards in the vehicle.~

WHILE DRIVING AT NIGHT, THE GEAR SHIFT INDICATOR LIGHT ON INSTRUMENT PANEL, SHINES BRIGHTER THAN OTHER COMPONENTS. *PE

*PE

industry awareness regarding the use of recycled or salvage parts.

Customers may experience the following:One or both of the vehicle?s headlamp assemblies are fogged with a light layer of condensation on the inside of the lenses.

industry awareness regarding the use of recycled or salvage parts.

Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.

Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

Library for specifications so a suitable alternative can be used

which replacement or repair of steering system components are required.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other componenets to be replaced). For more information and details on PN's, see L-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

pivot bushings.

pivot bushings.