2017 Volvo V90cc TSBs

Vehicle type and platform identification.

troubleshooting aid for the Intellisafe system, please follow the advice in Technical Journal

To provide timely and high-quality feedback to the appropriate department or factory

(Commonly Model Years 2016 And 2017)

found" or if functions such as lock/unlock are not working, please follow advice for detecting key

They are used in development of Volvo labor operations and repair methods, and promote safety and quality repairs in a timely manner. Tools are classified as mandatory because associated repairs and/or diagnostics cannot be completed properly without them.

and more precise fault tracing

and more precise fault tracing

They are used in development of Volvo labor operations and repair methods, and promote safety and quality repairs in a timely manner. Tools are classified as mandatory because associated repairs and/or diagnostics cannot be completed properly without them.

They are used in development of Volvo labor operations and repair methods, and promote safety and quality repairs in a timely manner. Tools are classified as mandatory because associated repairs and/or diagnostics cannot be completed properly without them.

and more precise fault tracing

New cleaning method developed.

Rear Seat Entertainment (RSE) accessory, it may be necessary to set the DVD region code to US (region 1)

apply grease

servicing distribution center.

The remotes do not function while the vehicle is in Transport Mode. See transport mode instructions

apply grease

friction and may create a noise when temperature are cold. The noise is most obvious during slow driving and turning (e.g. parking maneuvers). The noise will become less after some driving. Spray wax, Wurth PN 0893923284 , on the outer bellows

In order to restore the connectivity functions, the "Roaming" function must be activated in the vehicle menus.

and more precise fault tracing

description of affected seat covers before removal. Seat upholsteries are not to be replaced without contacting Volvo Technical Helpdesk (THD

For the cars in the header this DTC can be ignored as it doesn't affect any of the functions in the car. Do not perform any fault tracing or component replacement due to this DTC if there is no related customer symptom.

and more precise fault tracing

They are used in development of Volvo labor operations and repair methods, and promote safety and quality repairs in a timely manner. Tools are classified as mandatory because associated repairs and/or diagnostics cannot be completed properly without them.

In order to restore the connectivity functions, the "Roaming" function must be activated in the vehicle menus.

and more precise fault tracing

description of affected seat covers before removal. Seat upholsteries are not to be replaced without contacting Volvo Technical Helpdesk (THD

description of affected seat covers before removal. Seat upholsteries are not to be replaced without contacting Volvo Technical Helpdesk (THD

For the cars in the header this DTC can be ignored as it doesn't affect any of the functions in the car. Do not perform any fault tracing or component replacement due to this DTC if there is no related customer symptom.

New cleaning method developed.

found" or if functions such as lock/unlock are not working, please follow advice for detecting key

They are used in development of Volvo labor operations and repair methods, and promote safety and quality repairs in a timely manner. Tools are classified as mandatory because associated repairs and/or diagnostics cannot be completed properly without them.

description of affected seat covers before removal. Seat upholsteries are not to be replaced without contacting Volvo Technical Helpdesk (THD

New cleaning method developed.

found" or if functions such as lock/unlock are not working, please follow advice for detecting key

They are used in development of Volvo labor operations and repair methods, and promote safety and quality repairs in a timely manner. Tools are classified as mandatory because associated repairs and/or diagnostics cannot be completed properly without them.

friction and may create a noise when temperature are cold. The noise is most obvious during slow driving and turning (e.g. parking maneuvers). The noise will become less after some driving. Spray wax, Wurth PN 0893923284 , on the outer bellows

The locking retainer/washer must not be tight against the seat frame. It must have a play of 1,0mm +/-0,5mm.

and more precise fault tracing

The locking retainer/washer must not be tight against the seat frame. It must have a play of 1,0mm +/-0,5mm.

The locking retainer/washer must not be tight against the seat frame. It must have a play of 1,0mm +/-0,5mm.

CARS.THEY ARE USED IN DEVELOPMENT OF VOLVO LABOROPERATIONS AND REPAIR METHODS, AND PROMOTE SAFETY ANDQUALITY REPAIRS IN A TIMELY MANNER. TOOLS ARE CLASSIFIED AS MANDATORY BECAUSE ASSOCIATED REPAIRS AND/ORDIAGNOSTICS CANNOT BE COMPLETED PROPERLYWITHOUT THEM.

Replace the VCM Backup Battery and download the relevant Software.

Before joining a remote session:
 Connect a suitable battery maintainer/charger and verify that the battery voltage indicated in VIDA is between 12.5V and 14.9V.
 Connect to the vehicle over a wired connection using a VOE (Volvo OBD to Ethernet) adapter and perform a NEW vehicle readout.

Service:
 Dont charge the battery before the test, jump start the vehicle if needed. Read out the vehicle with VIDA and start the test.

Before joining a remote session:
 Connect a suitable battery maintainer/charger and verify that the battery voltage indicated in VIDA is between 12.5V and 14.9V.
 Connect to the vehicle over a wired connection using a VOE (Volvo OBD to Ethernet) adapter and perform a NEW vehicle readout.

Improved 12V battery test in VIDA

After capturing a NEW VIDA readout, conduct the steps in VIDA.

After capturing a NEW VIDA readout, conduct the steps in VIDA.

After capturing a NEW VIDA readout, conduct the steps in VIDA.

Improved 12V battery test in VIDA

Replace the VCM Backup Battery and download the relevant Software.

After capturing a NEW VIDA readout, conduct the steps in VIDA.

After capturing a NEW VIDA readout, conduct the steps in VIDA.

After capturing a NEW VIDA readout, conduct the steps in VIDA.

Use had held tester.

Recovering control modules stuck in not responding after failed SW download. Connect VIDA to read-out the car. Follow steps outlined in this TJ.

there is a warning message in the DIM about Low tire pressure and DTC BCM-C007768, follow advice under Service.

repair methods evolve.

System service required? displayed in DIM, then it is possible that there is water ingress into rear park assist sensors and connectors caused by splices in the rear cable harness. If the sensors and connectors have water ingress then follow method in VIDA

Perform Total Upgrade, replace fuse and compressor according to VIDA.

If not working check the heating grid wiring.

If not working check the heating grid wiring.

Swapping control modules may result in consequential damage to the swapped control module and in certain cases several other control modules in the vehicle. Swapping the Driver Information Module (DIM) is strictly forbidden as the DIM it is the main carrier of the odometer function, and will, in case of swapping, result in manipulated odometer value. Service: Please do NOT swap any control modules from vehicle to vehicle for testing, unless instructed to do so in a Vehicle Report by the Technical Helpdesk

Swapping control modules may result in consequential damage to the swapped control module and in certain cases several other control modules in the vehicle. Swapping the Driver Information Module (DIM) is strictly forbidden as the DIM it is the main carrier of the odometer function, and will, in case of swapping, result in manipulated odometer value. Service: Please do NOT swap any control modules from vehicle to vehicle for testing, unless instructed to do so in a Vehicle Report by the Technical Helpdesk

Volvo Car USA LLC and Volvo Car of Canada Ltd (Volvo) on behalf of Volvo Car Corporation, has decided to launch Service Action S39835 on certain model year 2017 XC90, S90, V90CC and V90 vehicles. The Vehicle Connectivity Module (VCM) contains telematics functions that may increase the current draw when the vehicle is not in use. The corrective action is to perform a Total Upgrade which contains new VCM software.

Action S39835 on certain model year 2017 XC90, S90, V90CC and V90 vehicles. The Vehicle Communication Module (VCM) contains telematics functions that may increase the current draw when the vehicle is not in use. The corrective action is to perform a Total Upgrade which contains new VCM software. Service Action S39835 affects 5,506 vehicles in the U.S. and 725 in Canada.

by providing a visible indication of error frames that are being transmitted on the network when the fault becomes active. The advantage of using the EFF function is that error frames are usually transmitted on the network before a vehicle symptom can occur. Hence, if the fault is very intermittent in nature, it may be possible, for example, to induce the wiring fault for a short duration by manipulating the vehicle harnesses and connectors. The electrical fault will occur and be detected by the EFF without ever having a vehicle symptom appear. The instructions for setting up the tool have been simplified.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

We process the personal data that you provide in connection with the creation of your VIDA account. The purpose of our processing is to administer your VIDA account (from registration to eventual termination of the account), to provide you with all the functionality related to VIDA, to allow access to VIDA and to communicate updates related to VIDA. Log data generated when using VIDA is processed as necessary or appropriate to safeguard the security and functionality of VIDA for example against malware or unauthorized access.

System service required? displayed in DIM, then it is possible that there is water ingress into rear park assist sensors and connectors caused by splices in the rear cable harness. If the sensors and connectors have water ingress then follow method in VIDA

System internal failures" is set. This is due to that the I-TPMS function in VDDM has not been initialized.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

manufacture and every 9 months thereafter.To maintain the battery, connect the battery to an appropriate 12V battery charger. Please follow all precautions that apply when charging a larger main lead-acid battery. The battery will self-discharge over time and if allowed to be left at a sufficiently low voltage, it will become permanently damaged. The battery must have a minimum voltage of 9 volts to be installed in a vehicle.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

Volvo Car USA LLC and Volvo Car Canada LTD (Volvo) on behalf of Volvo Car Group, has decided to launch Recall R39917 on certain model year 2017 ? 2019 XC90, S90, V60CC, V90, XC40, V60, XC60, V90CC vehicles. Volvo has identified that the Telematics and Driver Support Systems may not function as designed due to a software error in the Vehicle Connectivity Module (VCM). This could result in the vehicle not providing the GPS location, increasing the risk of no emergency response. The corrective action is to complete a Total Upgrade on all affected vehicles.

certain model year 2017 ? 2019 XC90, S90, V60CC, V90, XC40, V60, XC60, V90CC vehicles. Volvo has identified that the Telematics and Driver Support Systems may not function as designed due to a software error in the Vehicle Connectivity Module (VCM). This could result in the vehicle not providing the GPS location, increasing the risk of no emergency response. The corrective action is to complete a Total Upgrade on all affected vehicles. A total of 17,548 U.S. and 1,461 Canadian vehicles are eligible for this recall.

manufacture and every 9 months thereafter.To maintain the battery, connect the battery to an appropriate 12V battery charger. Please follow all precautions that apply when charging a larger main lead-acid battery. The battery will self-discharge over time and if allowed to be left at a sufficiently low voltage, it will become permanently damaged. The battery must have a minimum voltage of 9 volts to be installed in a vehicle.

Volvo Car USA LLC and Volvo Car Canada LTD (Volvo) on behalf of Volvo Car Group, has decided to launch Recall R39917 on certain model year 2017 ? 2019 XC90, S90, V60CC, V90, XC40, V60, XC60, V90CC vehicles. Volvo has identified that the Telematics and Driver Support Systems may not function as designed due to a software error in the Vehicle Connectivity Module (VCM). This could result in the vehicle not providing the GPS location, increasing the risk of no emergency response. The corrective action is to complete a Total Upgrade on all affected vehicles.

certain model year 2017 ? 2019 XC90, S90, V60CC, V90, XC40, V60, XC60, V90CC vehicles. Volvo has identified that the Telematics and Driver Support Systems may not function as designed due to a software error in the Vehicle Connectivity Module (VCM). This could result in the vehicle not providing the GPS location, increasing the risk of no emergency response. The corrective action is to complete a Total Upgrade on all affected vehicles. A total of 17,548 U.S. and 1,461 Canadian vehicles are eligible for this recall.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

Perform Total Upgrade, replace fuse and compressor according to VIDA.

System service required? displayed in DIM, then it is possible that there is water ingress into rear park assist sensors and connectors caused by splices in the rear cable harness. If the sensors and connectors have water ingress then follow method in VIDA

of the vehicle's Intellisafe systems. This graphic was removed from the software on May 12, 2017 due to some inaccuracies. Service: Affected software packages: - Total Upgrade - Service 2.0 - PDS (Pre-Delivery Service) - VDDM_PBL (Vehicle Dynamics Domain Master Primary Bootloader) - DIM Upgrade or Reload Any vehicle that received one of the software packages listed above from May 8th, 2017 to May 11th, 2017 will have received the DIM graphic. From May 12th, 2017 and on, if any of the software packages listed above are loaded to a car that has received the new graphic, it will be removed. Vehicles built from structure week 2017w17 to 2017w22 will have the graphic in the car from the factory but it will be removed when any of the software packages listed are loaded. Do NOT replace, reload or upgrade any components for customer complaints of this function missing. This function will be re-added to the DIM software at a later date that is to be determined.

open wiring diagram Final Solution: The only solution that we are aware of is to uninstall Adobe SVG viewer. Instructions below: Windows7/Windows 10: 1. Close VIDA. 2. Go into the Control Panel 3. Go into Program and Features - Uninstall program 4. Locate "Adobe SVG viewer" and uninstall it 5. Ignore any error message that might occur due to compability issues. 6. Start VIDA and try again.

If not working check the heating grid wiring.

open wiring diagram Final Solution: The only solution that we are aware of is to uninstall Adobe SVG viewer. Instructions below: Windows7/Windows 10: 1. Close VIDA. 2. Go into the Control Panel 3. Go into Program and Features - Uninstall program 4. Locate "Adobe SVG viewer" and uninstall it 5. Ignore any error message that might occur due to compability issues. 6. Start VIDA and try again.

System service required? displayed in DIM, then it is possible that there is water ingress into rear park assist sensors and connectors caused by splices in the rear cable harness. If the sensors and connectors have water ingress then follow method in VIDA

This TJ is released to inform that a method is changed in VIDA regarding replacement of fuel low pressure sensor (LPS). There are two different methods in VIDA depending on version of fuel low pressure sensor (LPS), see attached document. The method in VIDA can be found if searching for VST operation 28405-2.

This TJ is released to inform that a method is changed in VIDA regarding replacement of fuel low pressure sensor (LPS). There are two different methods in VIDA depending on version of fuel low pressure sensor (LPS), see attached document. The method in VIDA can be found if searching for VST operation 28405-2.

of the vehicle's Intellisafe systems. This graphic was removed from the software on May 12, 2017 due to some inaccuracies. Service: Affected software packages: - Total Upgrade - Service 2.0 - PDS (Pre-Delivery Service) - VDDM_PBL (Vehicle Dynamics Domain Master Primary Bootloader) - DIM Upgrade or Reload Any vehicle that received one of the software packages listed above from May 8th, 2017 to May 11th, 2017 will have received the DIM graphic. From May 12th, 2017 and on, if any of the software packages listed above are loaded to a car that has received the new graphic, it will be removed. Vehicles built from structure week 2017w17 to 2017w22 will have the graphic in the car from the factory but it will be removed when any of the software packages listed are loaded. Do NOT replace, reload or upgrade any components for customer complaints of this function missing. This function will be re-added to the DIM software at a later date that is to be determined.

The VIDA test is stillavailable but no longer required. For battery replacements under warranty, thecode generated by the BT3300 must bemanually copied into the repair order text. Itmust also be printed and attached to the hardcopy of the repair order.

S10303 on certain model year 2025 EX90 vehicles.
 Volvo Car Investigations have identified that there is a pairing issue with the key fob.
 As a result, there is a possibility that the customers key fob is not paired to the vehicle.
 The corrective action is to download SP Software.
 S10303 affects 151 vehicles in the U.S and 5 in Canada.

S10303 on certain model year 2025 EX90 vehicles.
 Volvo Car Investigations have identified that there is a pairing issue with the key fob.
 As a result, there is a possibility that the customers key fob is not paired to the vehicle.
 The corrective action is to download SP Software.
 S10303 affects 151 vehicles in the U.S and 5 in Canada.

If one control unit is upgraded and not all, it may result in various problems.

restore CSD functionality and/or complete software download

Service: *See guide updated Oct. 12, 2016 for relevant P5/SPA Software Download information: P5_SPA_SW_Guide.pdf See VIDA Software tab for all other vehicles.The attached checklists can be used for restoring customer settings, where applicable.

The corrective action is to perform a VDDM PBL software upgrade

If you receive this error message during a software download, use the Advanced Test function in the VIDA Software tab to read out the part number and serial number of the IHU. If the IHU indicates part number "0" and serial number "0000FFFFFFFF" the IHU must be replaced.

Service: *See guide updated Oct. 12, 2016 for relevant P5/SPA Software Download information: P5_SPA_SW_Guide.pdf See VIDA Software tab for all other vehicles.The attached checklists can be used for restoring customer settings, where applicable.

(full turn and acceleration), then follow advice under service. Download Total Upgrade software

customers, so that their cars give them the best experience possible . As of May 13th, 2019, when the software in your customer's vehicle is updated via Service 2.0 or Total Upgrade (TJ 31543), the customer will have access to the functions and improvements

customers, so that their cars give them the best experience possible . As of May 13th, 2019, when the software in your customer's vehicle is updated via Service 2.0 or Total Upgrade (TJ 31543), the customer will have access to the functions and improvements

Service: *See guide updated Oct. 12, 2016 for relevant P5/SPA Software Download information: P5_SPA_SW_Guide.pdf See VIDA Software tab for all other vehicles.The attached checklists can be used for restoring customer settings, where applicable.

Service: *See guide updated Oct. 12, 2016 for relevant P5/SPA Software Download information: P5_SPA_SW_Guide.pdf See VIDA Software tab for all other vehicles.The attached checklists can be used for restoring customer settings, where applicable.

release, will reset the sound settings back to default settings on the MY 2016 - 2018 vehicles listed above. The new software packages contain updated IHU software that will reset all customer sound settings such as treble, bass, balance and equalizer settings which will go back to default settings after the upgrade. For reference, please see attached example picture Sound.jpg. This applies to ALL driver profiles saved in the IHU. The VIDA IHU Diagnostic Sequences for Enabling the Export profile to USB menu will function after this upgrade.

Service: *See guide updated Oct. 12, 2016 for relevant P5/SPA Software Download information: P5_SPA_SW_Guide.pdf See VIDA Software tab for all other vehicles.The attached checklists can be used for restoring customer settings, where applicable.

(full turn and acceleration), then follow advice under service. Download Total Upgrade software

(full turn and acceleration), then follow advice under service. Download Total Upgrade software

under service.

under service.

under service.

Listed below are the latest planned owner notification re-mails. Please refer to SMB 00-323 and SMB 00-323A for information on how and where to find the related Service Action documents in VRC2 and TIE.

The WRCP is used to gauge individual retailer performance on objective measures over time. By setting clear performance expectations and parameters and assisting retailers in focusing on individual processes and procedures, all retailers are provided with adequate tools to help achieve the ultimate goal of qualifying for self-authorization status.

address non-warranty customer concerns in an expeditious manner. The ownership experience should never be compromised due to a customer inconvenience. In an effort to help support an enhanced customer ownership experience, Volvo retailers will now have the ability to self-authorize goodwill claims (1 time only per VIN) for the customers of the new MY2017 S90/V90 & V90CC.

Claims submitted for map upgrades will be debited

This bulletin is a list of equipment recommended by Volvo to it's dealer or any shop maintaining or repairing Volvo's. The equipment can be provided by Volvo's equipment supplier

This bulletin is a list of equipment recommended by Volvo to it's dealer or any shop maintaining or repairing Volvo's. The equipment can be provided by Volvo's equipment supplier

Volvo Car USA LLC and Volvo Car of Canada Ltd on behalf of Volvo Car Corporation, has decided to launch Service Campaign A39894 on certain model year 2019 XC90, XC60, V90CC, V90 and S90 vehicles. Volvo has identified that the vehicles equipped with a front and/or rear park assist system may not function as intended. However the rear park assist camera functions as intended. The corrective action is to perform a Total Upgrade.

This bulletin is a list of equipment recommended by Volvo to it's dealer or any shop maintaining or repairing Volvo's. The equipment can be provided by Volvo's equipment supplier

VCUSA Quality and Customer Satisfaction announces the IC Retainer Bolt Recall Customer Satisfaction Assistance Program. This program will allow Volvo retailers to proactively address customer satisfaction concerns as they relate to Recall R89174 repairs in an expeditious manner.

By setting clear performance expectations and parameters and assisting retailers in focusing on individual processes and procedures, all retailers are provided with adequate tools to help achieve the ultimate goal of qualifying for self authorization status.

VIDA will run slow after some time. VIDA might freeze. Certain operations might stop working.In order to release stored session memory, restart VIDA as needed throughout the day in order to minimize the risk to experience above symptoms.

VEHICLE INSPECTION PROCEDURE (TRUCK DELIVERY) PRE-DELIVERY SERVICE (PDS) VEHICLE IN STOCK MAINTENANCE VEHICLE DELIVERY (CUSTOMER DELIVERY) NEW CAR DELIVERY IS A CRUCIAL STEP IN THE RETAIL CAR DELIVERY PROCESS. AT THIS POINT THE BUYING EXPERIENCE TURNS INTO A LONG-TERM RELATIONSHIP. IT IS THE RETAILERS RESPONSIBILITY TO ENSURE THAT THE CAR AND THE EXPERIENCE ARE AS ENJOYABLE AND INFORMATIVE AS POSSIBLE.

Radial force variation ( RFV ) is a condition where excessive run out will create the same symptom as an unbalanced tire. Tire balancing should be checked and corrected as needed but is not always the solution. Road Force balancing detects assembly run out measured under load simulating real world driving conditions and will provide a solution to match mount the tire and rim to minimize loaded run out.

If TPMS warning symbol is flashing in DIM with a "TPMS Service Required" message, then follow advice under Service

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

stamping, name and size.

be prepared for these issues.

Radial force variation ( RFV ) is a condition where excessive run out will create the same symptom as an unbalanced tire. Tire balancing should be checked and corrected as needed but is not always the solution. Road Force balancing detects assembly run out measured under load simulating real world driving conditions and will provide a solution to match mount the tire and rim to minimize loaded run out.

stamping, name and size.

be prepared for these issues.

Radial force variation ( RFV ) is a condition where excessive run out will create the same symptom as an unbalanced tire. Tire balancing should be checked and corrected as needed but is not always the solution. Road Force balancing detects assembly run out measured under load simulating real world driving conditions and will provide a solution to match mount the tire and rim to minimize loaded run out.

Service: In case of vibrations, please follow TJ 20803 to establish the if the vibrations are coming from powertrain components or from wheels/tires. If analysis indicate that the vibrations are coming from the wheels/tires, then follow TJ 32161.

stamping, name and size.

stamping, name and size.

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

Service: In case of vibrations, please follow TJ 20803 to establish the if the vibrations are coming from powertrain components or from wheels/tires. If analysis indicate that the vibrations are coming from the wheels/tires, then follow TJ 32161.

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

Before carrying out this TJ, always start with TJ 20803 to sort out if the problem is related to driveline or wheels.

stamping, name and size.

from the headlining around the sun roof, see instructions under Service referring to TJI-516730-1_1_0

Hood" DIM message, please follow advice under "service". And before replacing any parts, follow the 3 steps in the instructions.

Hood" DIM message, please follow advice under "service". And before replacing any parts, follow the 3 steps in the instructions.

Expose vehicle to outside daylight for 48hrs.

May required replacing terminals.

If the analysis shows that the rattling noise comes from the roller blind, similar to the noise in the attached file, replace the roller blind according to VIDA.

If the analysis shows that the rattling noise comes from the roller blind, similar to the noise in the attached file, replace the roller blind according to VIDA.

If the analysis shows that the rattling noise comes from the roller blind, similar to the noise in the attached file, replace the roller blind according to VIDA.

If the analysis shows that the rattling noise comes from the roller blind, similar to the noise in the attached file, replace the roller blind according to VIDA.

If the analysis shows that the rattling noise comes from the roller blind, similar to the noise in the attached file, replace the roller blind according to VIDA.

Will only be performed at 20k

Apply grease P/N 31437986

Apply new sealing compound ~20-30 cm (8 to 11 inches) on top of the original glue on the upper part of the beam, so that you get contact between the beam and the outer door panel. Do not push the outer door panel when applying the glue, see attached picture TJ32381.jpg. Diameter of the glue: 8 mm. P/N: 1161767 (VIDA P/N) replaced by Volvo Chemical Portal US P/N: 08901002 Volvo Chemical Portal Canada P/N: 890.1003

Apply new sealing compound ~20-30 cm (8 to 11 inches) on top of the original glue on the upper part of the beam, so that you get contact between the beam and the outer door panel. Do not push the outer door panel when applying the glue, see attached picture TJ32381.jpg. Diameter of the glue: 8 mm. P/N: 1161767 (VIDA P/N) replaced by Volvo Chemical Portal US P/N: 08901002 Volvo Chemical Portal Canada P/N: 890.1003

Apply new sealing compound ~20-30 cm (8 to 11 inches) on top of the original glue on the upper part of the beam, so that you get contact between the beam and the outer door panel. Do not push the outer door panel when applying the glue, see attached picture TJ32381.jpg. Diameter of the glue: 8 mm. P/N: 1161767 (VIDA P/N) replaced by Volvo Chemical Portal US P/N: 08901002 Volvo Chemical Portal Canada P/N: 890.1003

Download software.

Action S29878 on certain model year 2017 - 2018 XC90, S90, V90, V90CC, XC60 vehicles. Volvo has identified that the lower flap in the capless unit that is located inside the fuel tank filler pipe, intermittently may not close completely after refueling. This could result in a Check Engine Light and Diagnostic Trouble Code ECM-P0044200.

VGT, TC) And US17+OBD22 (11L) Emissions

Make sure that the sound is coming from the engine pad, NOT from the drive shaft. Remove the left engine pad and split by removing the small screw. Lubricate with graphite grease (PN 1161851) on points as in attachment. Torque for small screw is 8 nm.

Make sure that the sound is coming from the engine pad, NOT from the drive shaft. Remove the left engine pad and split by removing the small screw. Lubricate with graphite grease (PN 1161851) on points as in attachment. Torque for small screw is 8 nm.

Make sure that the sound is coming from the engine pad, NOT from the drive shaft. Remove the left engine pad and split by removing the small screw. Lubricate with graphite grease (PN 1161851) on points as in attachment. Torque for small screw is 8 nm.

( see attached sample files ). The sound may come from the balance shaft which is fitted in the oil sump area where the noise is most concentrated. A new design of the balance shaft is planned to be introduced 2018-Q2. Replace the balance shaft according the instructions in VIDA. Note: It's extremely important to adjust the new balance shaft with the correct tools according the instructions otherwise the sound may occur again in a short mileage.

VCM software release can cause any or all of the above symptoms. *The current solution is to install VCM repair software by following the procedure below: 1. Perform a Total Upgrade according to TJ 31543 to bring all vehicle nodes to the latest software status. The Upgrades list in VIDA should be empty before proceeding. *2. Download the appropriate SP below to prevent the above symptoms and re-enable ERS XC90: SP 31676890, CMQ VCM Fix S90: SP 31676891, CMQ VCM Fix 3. Drive the vehicle over 20mph to release the VCM from diagnostic mode. ERS will be unavailable until this is done. 4. Close and lock the vehicle for 3+ minutes to allow the network to shut down before testing ERS. PLEASE NOTE - DO NOT perform a Total Upgrade or VCM Upgrade after performing this procedure (they will now appear in the Upgrades list). Doing so will re-install the affected software. - Not all battery drains are caused by this issue. *The repair software will be integrated with regular VCM Upgrade/Reload and Total Upgrade/PDS/Service 2.0 packages in the coming weeks *This TJ will be updated when the updated software packages are available.

To protect the throttle housing when using Volvo Car Showmode kit in the specified cars, always remove the connector from the throttle housing (see picture 34206.jpg) A new software for the BRIGO device is under development to avoid this damage. Make sure that the BRIGO device always updated with the latest software.

To protect the throttle housing when using Volvo Car Showmode kit in the specified cars, always remove the connector from the throttle housing (see picture 34206.jpg) A new software for the BRIGO device is under development to avoid this damage. Make sure that the BRIGO device always updated with the latest software.

Do not replace any parts for these cases. A new software for the ECM (engine control module) is under development and is planned to be released Q4-2018

ISSUING DEPARTMENT : CAR MARKET : United States and Canada TJ 19245 Technical Service PARTNER : ISSUE DATE : 3 US 7510 Volvo Cars North America YEAR MONTH DAY 2014 02 06 FUNC GROUP : FUNC DESC : 0 Publications Page 1 of 3 Attachment Vehicle Type Eng Struc Week Type Eng Sales Body Gear Steer Model Year Plant Chassis range Desc Range XXX 1927 - 9999 0000001 - 0999999 0 - 0 CSC Customer Symptom Codes Code Description 1C Administrative and Factory scheduled maintenance/Administrative and Factory scheduled maintenance DTC Diagnostic Trouble Codes Rows beginning with * are modified Note ! If using a printed copy of this Technical Journal, first check for the latest online version. Text In our Service Literature, a vehicle is often referred to by its ?type ?, not its ?model ?. For example the 1999 - 2006 Model Year S80 is type ?184? You may also see the designation, for example ?P2X?. This is referring to a platform type or vehicle family. If a document states ?P1X? or ?5XX? as an example, it will apply to all models within the platform type. ?54X? will apply to the ?544?, ?545? and ?542? models. ?X? represents variable data. ?Right first time in Time? Produced in the USA and available as an electronic document . Hard copy documents are printed in USA on recycled paper containing a minimum of 50% wastepaper and 10% post - consumer waste . 014 VOLVO CARS OF NORTH AMERICA, LLC Technical Journal 19245 Platform Model Type Model Years Comments P3 S80 124 2007 - V70 135 2008 - 2010 XC70 136 2008 - XC60 156 2010 - S60 134 2011 - V60 155 2015 - P2 S80 184 1999 - 2006 V70 285 2001 - 2007 XC70 295 2001 - 2007 S60 384 2001 - 2009 XC90 275 2003 - P1 S40 544 2004 - 2012 V50 545 2005 - 2012 C30 533 2007 - 2013 C70 542 2006 - 2013 X40 S40 644 2000 - 2004 V40 645 2000 - 2004 900 940 944 1991 - 1995 four cylinder, four door 940

( see attached sample files ). The sound may come from the balance shaft which is fitted in the oil sump area where the noise is most concentrated. A new design of the balance shaft is planned to be introduced 2018-Q2. Replace the balance shaft according the instructions in VIDA. Note: It's extremely important to adjust the new balance shaft with the correct tools according the instructions otherwise the sound may occur again in a short mileage.

( see attached sample files ). The sound may come from the balance shaft which is fitted in the oil sump area where the noise is most concentrated. A new design of the balance shaft is planned to be introduced 2018-Q2. Replace the balance shaft according the instructions in VIDA. Note: It's extremely important to adjust the new balance shaft with the correct tools according the instructions otherwise the sound may occur again in a short mileage.

internet connection is available (globe in the top left corner), follow the instructions under "service".
 This Technical Journal handles only SENSUS vehicles.

the Centre Display for I-TPMS is showing a "spinning wheel", while calibration is ongoing. The calibration function itself is not changed compared to previous SW versions, it is only how it is presented in the center display that has been changed.A new calibration will start automatically as soon as the VDDM SW is upgraded.

Download software.

May 2017

When this happens the CCD and the center area of the DIM will go blank for a few moments and then start back up as if the vehicle has just been started up.

When this happens the CCD and the center area of the DIM will go blank for a few moments and then start back up as if the vehicle has just been started up.

the Centre Display for I-TPMS is showing a "spinning wheel", while calibration is ongoing. The calibration function itself is not changed compared to previous SW versions, it is only how it is presented in the center display that has been changed.A new calibration will start automatically as soon as the VDDM SW is upgraded.

to objects that may shield radio communication between the remote control key and the car or could cause interference with they key signals..

to objects that may shield radio communication between the remote control key and the car or could cause interference with they key signals..

When this happens the CCD and the center area of the DIM will go blank for a few moments and then start back up as if the vehicle has just been started up.

When this happens the CCD and the center area of the DIM will go blank for a few moments and then start back up as if the vehicle has just been started up.

When this happens the CCD and the center area of the DIM will go blank for a few moments and then start back up as if the vehicle has just been started up.

If the result is not ok (air leak), it is ok to replace the headlamp

This logic of the cornering lights is now changed in the cars with software version 3.3.16 or later

If the result is not ok (air leak), it is ok to replace the headlamp

Complimentary Factory Scheduled Maintenance Program. Model Year 2013 and later vehicles, the service intervals are every 10,000 miles and ALL 2013 and later vehicles must use synthetic oil only.

Factory Scheduled Maintenance up to the first 3 years or 36,000 miles (whichever comes first) as recommended in the Volvo Warranty and Maintenance Information booklet.

At PDS and when attempting to diagnose a customer concern regarding voice controls not working or responding properly, make sure the vehicle has the latest voice control database installed.

At PDS and when attempting to diagnose a customer concern regarding voice controls not working or responding properly, make sure the vehicle has the latest voice control database installed.

your servicing distribution center.

Warranty GROUP : NO : ISSUING DEPARTMENT : CAR MARKET : Warranty Canada 00 342C REFERENCE BULLETINS : DATE : YEAR MONTH DAY SERVICE SERVICE WARRANTY 2015 09 18 MANAGER WRITER ADMINISTRATOR Service Personnel : Read and initial Page 1 of 4 VOLVO LIFETIME REPLACEMENT PARTS & LABOUR WARRANTY CUSTOMER OFFER To further enhance the Volvo ownership experience , Volvo Cars of Canada Corp . is offering the Volvo Lifetime Replacement Parts & Labour Warranty . Volvo warrants to the original retail purchaser of each new genuine Volvo replacement part ( excluding accessories and consumable parts as listed below ) that such part installed at an authorized Volvo retailer will be free from defects in material or workmanship . This would exclude any defects caused by outside influence . Coverage under the Lifetime Replacement Parts & Labour Warranty includes the labour to replace the covered replacement part . This warranty is nontransferable . COVERAGE Beginning with repairs dated on or after September 15 , 2015 , the original retail purchaser of a new genuine Volvo replacement part purchased and installed at an authorized Volvo retailer will be eligible for the Volvo Lifetime Replacement Parts & Labour Warranty . Parts and labour coverage under this Lifetime Warranty are only applicable when the new replacement part has been purchased and installed at an authorized Volvo retailer . Parts sold over the counter that are not installed by an authorized Volvo retailer are covered by Volvo?s one year parts only warranty . ? Right first time in Time ? Produced in the USA and available as an electronic document . Hard copy documents are printed in USA on recycled paper containing a minimum of 50 % wastepaper and 10 % post - consumer waste . 2015 VOLVO CARS OF NORTH AMERICA , LLC Service Manager Bulletin 00 - 342C As part of the vehicle?s normal service and maintenance

At PDS and when attempting to diagnose a customer concern regarding voice controls not working or responding properly, make sure the vehicle has the latest voice control database installed.

Download software fix

Download software fix

or 36,000 miles (whichever comes first) as recommended in the Volvo Warranty and Maintenance Information booklet.

At PDS and when attempting to diagnose a customer concern regarding voice controls not working or responding properly, make sure the vehicle has the latest voice control database installed.

At PDS and when attempting to diagnose a customer concern regarding voice controls not working or responding properly, make sure the vehicle has the latest voice control database installed.

then this could be caused by radar reflection from material around the SOD. Then follow the advice under Service. Install the service kit PN 32217315 according to TJ instruction.

Replace HVCH.

replace the heater core according to the attached instruction.

Replace with new caps on wheel screws

the calendar function in the car and direct start of the climate settings from the app does work, please follow the advice under service. Service: Do not replace any parts or perform any fault-tracing. The fix will be in the Software upgrade package at the dates stated below: *- 2018 week 19 there is a software release for XC90, S90, V90 built from and including structure week 201746. *- 2018 week 22 there is a software release where the fix is included for the XC40, new XC60, XC90, S90, V90 built before structure week 201746. * Please perform a Total Upgrade in accordance with TJ 31543.

replace the heater core according to the attached instruction.

Total Upgrade should be used if there are any upgrades available. - Perform an IHU Reload

Perform action according to instructions for different car variants.

Perform action according to instructions for different car variants.

the calendar function in the car and direct start of the climate settings from the app does work, please follow the advice under service. Service: Do not replace any parts or perform any fault-tracing. The fix will be in the Software upgrade package at the dates stated below: *- 2018 week 19 there is a software release for XC90, S90, V90 built from and including structure week 201746. *- 2018 week 22 there is a software release where the fix is included for the XC40, new XC60, XC90, S90, V90 built before structure week 201746. * Please perform a Total Upgrade in accordance with TJ 31543.

New foam rings between upper actuators (4 zones) and shafts in the Climate unit have been implemented in plant from 2017w04. In case of customer complaints, install new foamrings according the attached instruction. S/V90 4-zone XC90 4-zone S/V90 2-zone XC90 2-zone

certain model year 2017 XC90, S90, V90CC and V90 vehicles. Due to a manufacturing error in the surface treatment process, the bolts that were used to assemble the inflatable curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

certain model year 2017 XC90, S90, V90CC and V90 vehicles. Due to a manufacturing error in the surface treatment process, the bolts that were used to assemble the inflatable curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

certain model year 2017 XC90, S90, V90CC and V90 vehicles. Due to a manufacturing error in the surface treatment process, the bolts that were used to assemble the inflatable curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

certain model year 2017 XC90, S90, V90CC and V90 vehicles. Due to a manufacturing error in the surface treatment process, the bolts that were used to assemble the inflatable curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

certain model year 2017 XC90, S90, V90CC and V90 vehicles. Due to a manufacturing error in the surface treatment process, the bolts that were used to assemble the inflatable curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

certain model year 2017 XC90, S90, V90CC and V90 vehicles. Due to a manufacturing error in the surface treatment process, the bolts that were used to assemble the inflatable curtain (IC) airbag may not meet specifications. This could result in one or more of the bolts breaking within 48 hours of installation, which in the event of a crash warranting deployment of the IC airbag, could increase the risk of injury to vehicle occupants. The correction action is for Volvo retailers to replace all of the inflatable curtain bolts.

Seat Belt Extender.

Add adhesive tape.

Seat Belt Extender.

Add adhesive tape.

Seat Belt Extender.

Seat Belt Extender.

Volvo Car USA LLC and Volvo Car of Canada Ltd (Volvo) on behalf of Volvo Car Corporation, has decided to launch Service Action S39816 on certain model year 2016 - 2017 XC90 and 2017 S90, V90CC and V90 vehicles. Volvo has identified that due to a software deviation in the Vehicle Dynamics Domain Master (VDDM) Primary Boot Loader (PBL), the vehicle may not start after it has been parked and the parking brake lamp will be lit in the instrument panel. The corrective action is to perform a VDDM PBL software upgrade.

(PBL), the vehicle may not start after it has been parked and the parking brake lamp will be lit in the instrument panel. Model Year 2016-2017 XC90, & 2017 S90, V90CC, V90

If squealing noise occur from rear brakes 17" at low speed, follow advice under service. If symptom is confirmed, follow advice in VIDA regarding greasing method when changing the brake pads.

guideline has been developed, as an overview of the brake noise and indicates possible faults/solutions.

(customer behavoiur information) of a car is required from Volvo Car Corporation from external sources, either of these two documents should be filled in and attached to the affected Vehicle Report. (External sources: Authority, Insurance companies, Rental companies, etc)

If squealing noise occur from rear brakes 17" at low speed, follow advice under service. If symptom is confirmed, follow advice in VIDA regarding greasing method when changing the brake pads.

(customer behavoiur information) of a car is required from Volvo Car Corporation from external sources, either of these two documents should be filled in and attached to the affected Vehicle Report. (External sources: Authority, Insurance companies, Rental companies, etc)

Add resister in line jumper cable.

Add resister in line jumper cable.

Due to an internal can bus data error in the TCM, harsh garage shifts may occur at P-R, R-D, N-D. New improved TCM SW is planned to be released 2017w22 in production and service. If you have a customer complaint at this time, perform a TCM reload. This will reset the values of the TCM and improve shift quality .

Due to an internal can bus data error in the TCM, harsh garage shifts may occur at P-R, R-D, N-D. New improved TCM SW is planned to be released 2017w22 in production and service. If you have a customer complaint at this time, perform a TCM reload. This will reset the values of the TCM and improve shift quality .

MARKET : United States and Canada TJ 25153 Technical Service PARTNER : ISSUE DATE : STATUS DATE : 3 US 7510 Volvo Car USA 2016 - 03 - 17 2016 - 03 - 24 FUNC GROUP : FUNC DESC : 3634 Washer Page 1 of 24 Attachment File Name File Size TJ 25153 S60 MY11 - , V60 , S60 , V60CC.pdf 0.8349 MB TJ 25153 S80 MY07 - , V70 MY08 - , XC70 MY08 - . pdf 0.7857 MB TJ 25153 S90 ( 234 ) MY17 - . pdf 1.4623 MB TJ 25153 V90V90CC ( 235236 ) MY17 - . pdf 1.5192 MB TJ 25153 XC90 ( 256 ) MY16 - . pdf 2.1365 MB TJ 25153_XC60 . pdf 0.8801 MB Vehicle Type Eng Struc Week Type Eng Sales Body Gear Steer Model Year Plant Chassis range Desc Range 124 2007 - 9999 0000850 - 9999999 200605 - 999952 134 2011 - 9999 0000194 - 9999999 201020 - 999952 135 2008 - 9999 0000395 - 9999999 200720 - 999952 136 2008 - 9999 0000400 - 9999999 200720 - 999952 138 2016 - 9999 0000122 - 9999999 201345 - 999952 155 2015 - 9999 0001147 - 9999999 201035 - 999952 156 2009 - 9999 0000212 - 9999999 200835 - 999952 157 2016 - 9999 0000022 - 9999999 201450 - 999952 234 2017 - 9999 0000001 - 9999999 201617 - 999952 235 2017 - 9999 0000001 - 9999999 201617 - 999952 236 2017 - 9999 0000001 - 9999999 201617 - 999952 256 2016 - 9999 0000001 - 9999999 201505 - 999952 ? Right first time in Time ? Produced in the USA and available as an electronic document . Hard copy documents are printed in USA on recycled paper containing a minimum of 50 % wastepaper and 10 % post - consumer waste . 2016 VOLVO CAR USA , LLC Technical Journal 25153 CSC Customer Symptom Codes Code Description 1U Washer fluid reservoir / hoses / Leakage VST Operation Number DTC Diagnostic Trouble Codes Rows beginning with * are modified Note ! If using a printed copy of this Technical Journal , first check for the latest online version . Text DESCRIPTION : If leakage occurs in the washer system at any of the multiple

ISSUING DEPARTMENT : CAR MARKET : United States and Canada TJ 19245 Technical Service PARTNER : ISSUE DATE : 3 US 7510 Volvo Cars North America YEAR MONTH DAY 2014 02 06 FUNC GROUP : FUNC DESC : 0 Publications Page 1 of 3 Attachment Vehicle Type Eng Struc Week Type Eng Sales Body Gear Steer Model Year Plant Chassis range Desc Range XXX 1927 - 9999 0000001 - 0999999 0 - 0 CSC Customer Symptom Codes Code Description 1C Administrative and Factory scheduled maintenance / Administrative and Factory scheduled maintenance DTC Diagnostic Trouble Codes Rows beginning with * are modified Note ! If using a printed copy of this Technical Journal , first check for the latest online version . Text In our Service Literature , a vehicle is often referred to by its ? type ? , not its ? model ? . For example the 1999 - 2006 Model Year S80 is type ? 184 ? . You may also see the designation , for example ? P2X ? . This is referring to a platform type or vehicle family . If a document states ? P1X ? or ? 5XX ? as an example , it will apply to all models within the platform type . ? 54X ? will apply to the ? 544 ? , ? 545 ? and ? 542 ? models . ? X ? represents variable data . ? Right first time in Time ? Produced in the USA and available as an electronic document . Hard copy documents are printed in USA on recycled paper containing a minimum of 50 % wastepaper and 10 % post - consumer waste . 2014 VOLVO CARS OF NORTH AMERICA , LLC Technical Journal 19245 Platform Model Type Model Years Comments P3 S80 124 2007 - V70 135 2008 - 2010 XC70 136 2008 - XC60 156 2010 - S60 134 2011 - V60 155 2015 - P2 S80 184 1999 - 2006 V70 285 2001 - 2007 XC70 295 2001 - 2007 S60 384 2001 - 2009 XC90 275 2003 - P1 S40 544 2004 - 2012 V50 545 2005 - 2012 C30 533 2007 - 2013 C70 542 2006 - 2013 X40 S40 644 2000 - 2004 V40 645 2000 - 2004 900 940 9

Due to an internal can bus data error in the TCM, harsh garage shifts may occur at P-R, R-D, N-D. New improved TCM SW is planned to be released 2017w22 in production and service. If you have a customer complaint at this time, perform a TCM reload. This will reset the values of the TCM and improve shift quality .

Technical Service PARTNER : ISSUE DATE : 3 US 7510 Volvo Cars North America YEAR MONTH DAY 2012 10 11 FUNC GROUP : FUNC DESC : 3521 Headlamp , complete Page 1 of 24 Attachment File Name File Size S80 - V70 - XC70 . pdf 0.5641 MB S60 - XC60 . pdf 0.5868 MB C30 - S40 - V50 - C70 . pdf 0.4175 MB XC90 . pdf 0.6020 MB Vehicle Type Eng Struc Week Type Eng Sales Body Gear Steer Model Year Plant Chassis range Desc Range 124 2007 - 9999 0000850 - 9999999 200605 - 999952 134 2011 - 9999 0000194 - 9999999 201020 - 999952 135 2008 - 2010 0000395 - 9999999 200720 - 999952 136 2008 - 9999 0000400 - 9999999 200720 - 999952 156 2010 - 9999 0000395 - 9999999 200720 - 999952 275 2003 - 9999 0000690 - 9999999 200232 - 999952 533 2007 - 9999 0000261 - 9999999 200637 - 999952 542 2006 - 9999 0000590 - 0999999 200549 - 999952 544 2004 - 2010 0000295 - 0999999 200339 - 999952 545 2004 - 2010 0000133 - 0999999 200347 - 999952 CSC Customer Symptom Codes Code Description W4 Headlights / Moisture / mist on inside of lens WG Headlights / Lens broken / chipped / cracked / distorted ? Fixed Right ? First Time ? Produced in the USA and available as an electronic document . Hard copy documents are printed in USA on recycled paper containing a minimum of 50 % wastepaper and 10 % post - consumer waste . 2012 VOLVO CARS OF NORTH AMERICA , LLC Technical Journal 17076 DTC Diagnostic Trouble Codes Text CSC = Customer Symptom Code DTC = Diagnostic Trouble Code Note ! If using a printed copy of this Retailer Technical Journal , first check for the latest online version . DESCRIPTION : The headlamp assembly may have condensation caused by moisture inside of lens . Some condensation is normal and not considered a defect . Automotive lamps are designed as an open system and atmospheric humidity can enter the lamp and also exit . The moisture disappears over a time period through the air v

ISSUING DEPARTMENT : CAR MARKET : United States and Canada TJ 19245 Technical Service PARTNER : ISSUE DATE : 3 US 7510 Volvo Cars North America YEAR MONTH DAY 2014 02 06 FUNC GROUP : FUNC DESC : 0 Publications Page 1 of 3 Attachment Vehicle Type Eng Struc Week Type Eng Sales Body Gear Steer Model Year Plant Chassis range Desc Range XXX 1927 - 9999 0000001 - 0999999 0 - 0 CSC Customer Symptom Codes Code Description 1C Administrative and Factory scheduled maintenance / Administrative and Factory scheduled maintenance DTC Diagnostic Trouble Codes Rows beginning with * are modified Note ! If using a printed copy of this Technical Journal , first check for the latest online version . Text In our Service Literature , a vehicle is often referred to by its ? type ? , not its ? model ? . For example the 1999 - 2006 Model Year S80 is type ? 184 ? . You may also see the designation , for example ? P2X ? . This is referring to a platform type or vehicle family . If a document states ? P1X ? or ? 5XX ? as an example , it will apply to all models within the platform type . ? 54X ? will apply to the ? 544 ? , ? 545 ? and ? 542 ? models . ? X ? represents variable data . ? Right first time in Time ? Produced in the USA and available as an electronic document . Hard copy documents are printed in USA on recycled paper containing a minimum of 50 % wastepaper and 10 % post - consumer waste . 2014 VOLVO CARS OF NORTH AMERICA , LLC Technical Journal 19245 Platform Model Type Model Years Comments P3 S80 124 2007 - V70 135 2008 - 2010 XC70 136 2008 - XC60 156 2010 - S60 134 2011 - V60 155 2015 - P2 S80 184 1999 - 2006 V70 285 2001 - 2007 XC70 295 2001 - 2007 S60 384 2001 - 2009 XC90 275 2003 - P1 S40 544 2004 - 2012 V50 545 2005 - 2012 C30 533 2007 - 2013 C70 542 2006 - 2013 X40 S40 644 2000 - 2004 V40 645 2000 - 2004 900 940 9

U023292 REF NO : ISSUING DEPARTMENT : CAR MARKET : United States and Canada TJ 30858 Technical Service PARTNER : ISSUE DATE : STATUS DATE : 3 US 7510 Volvo Cars North America 2015 - 10 - 16 2015 - 10 - 21 FUNC GROUP : FUNC DESC : 3872 Collision avoidance Page 1 of 2 Attachment Vehicle Type Eng Struc Week Type Eng Sales Body Gear Steer Model Year Plant Chassis range Desc Range 256 2016 - 2016 0000516 - 0035745 201505 - 201539 CSC Customer Symptom Codes Code Description XR Blind spot information system ( BLIS ) / Does not work IV Text window and warning symbol / Text message VST Operation Number VST Operation Number Description 36004 - 2 Software control module downloading DTC Diagnostic Trouble Codes Text ? Right first time in Time ? Produced in the USA and available as an electronic document . Hard copy documents are printed in USA on recycled paper containing a minimum of 50 % wastepaper and 10 % post - consumer waste . 2015 VOLVO CARS OF NORTH AMERICA , LLC Technical Journal 30858 DESCRIPTION : Note ! If using a printed copy of this Technical Journal , first check for the latest online version . If a warning message ? BLIS system service required ? occurs in DIM together with DTC SODR - U023292 or / and SODL - U023292 , then follow the advice under SERVICE . Vehicle Report : Only if this TJ does not solve the problem or if the symptom would occur after the chassis number ranges above . Use concern area ? Vehicle Report ? and sub concern area ? Support Needed ? , use function group 3872 . Service : In case of customer complaints for above symptom , download SOD upgrade . ( side object detection module ) Page 2 of 2 2015 - 10 - 21

turning the steering wheel, follow the advice under Service.

Check rubber gromet in firewall