2006 Volkswagen Touareg TSBs

The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage. Proceed with checking any other lines as necessary. Once the damaged line is identified, repair utilizing the Repair kit by Permatex ITEM 09117.

The door lock cylinder does not disarm the alarm. The lock cylinder in the door is meant to be used as an emergency entry, therefore the key must be inserted into the ignition within 15-30 seconds of opening the door (dependent on vehicle and equipment), in order to disarm the alarm.

When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121).

damaged compression wheel, loose or broken shaft), it is not enough to just replace the turbocharger.

The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not.

exterior paint finish.

Also includes 2004 and 2005 Jetta Wagon and 2018-2020 Tiguan LWB

with servicing engine control module issues:

and underside of hood may not match the exterior paint color of the vehicle. Depending on vehicle model and production plant, the color of the engine compartment and underside hood may not match the vehicle body color. This document informs dealers to let their customers know that these body surfaces (engine compartment and underside of hood) are not directly visible (exposed) and therefore do not require the same finish as visible, exterior surfaces.

is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications.

oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. This document informs how to test the oil consumption rate

using the door key, the alarm may activate when opening the door. The door lock cylinder does not disarm the alarm. The lock cylinder in the door is meant to be used as an emergency entry, therefore the key must be inserted into the ignition within 15-30 seconds of opening the door (dependent on vehicle and equipment), in order to disarm the alarm.

associated with servicing engine control module issues:

and underside of hood may not match the exterior paint color of the vehicle. Depending on vehicle model and production plant, the color of the engine compartment and underside hood may not match the vehicle body color. This document informs dealers to let their customers know that these body surfaces (engine compartment and underside of hood) are not directly visible (exposed) and therefore do not require the same finish as visible, exterior surfaces.

is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications.

oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. This document informs how to test the oil consumption rate

using the door key, the alarm may activate when opening the door. The door lock cylinder does not disarm the alarm. The lock cylinder in the door is meant to be used as an emergency entry, therefore the key must be inserted into the ignition within 15-30 seconds of opening the door (dependent on vehicle and equipment), in order to disarm the alarm.

standards lists to current specifications. Engine Oils Which Meet Volkswagen Oil Quality Standards

(Engine Oil, Manual Transmission, Automatic Transmission, Differential Automatic Transmission, Cooling System, Power Steering, Windshield Washer, A/C Refrigerant, A/C Refrigerant Oil

damaged compression wheel, loose or broken shaft), it is not enough to just replace the turbocharger. This document informs the procedure of checks for damage.

consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. This document informs of oil consumption tests to check a vehicles performance.

case while performing diagnosis for a diesel particulate filter, manual transmission repair, or turbocharger concern, it is recommended to complete the related worksheet/check sheet before calling. This document informs where Worksheets/Check Sheets are available on ServiceNet.

consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owners Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Further factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this document can be performed. This document contains the procedure for the VW method to remove musty odors

content of deposit control additives may result in one or more of the following conditions: -Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. -Engine runs rough after cold start. -Excessive engine cranking time. -Stumbles while driving. -Rough engine idle. -Loss of engine performance. -Poor fuel economy. This document informs of the procedure for the vehicle if it is diagnoised with poor quality gas

meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage.

performance, efficiency and service life of the engine. The use of poor quality fuels may result in deposit build up on the fuel injectors and intake valves. This may result in a rough running condition, sporadic misfires, or cold start misfire faults storing in the ECM fault memory. This document informs a Volkswagen approved fuel additive is available to help remove and prevent deposits on fuel injectors and intake valves.

performance, efficiency and service life of the engine. The use of poor quality fuels may result in deposit build up on the fuel injectors and intake valves. This may result in a rough running condition, sporadic misfires, or cold start misfire faults storing in the ECM fault memory. A Volkswagen approved fuel additive is available to help remove and prevent deposits on fuel injectors and intake valves. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

it is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications. The production solution to service this issue is that no production change is required.

and prevent deposits on fuel injectors and intake valves.

Document contains examples of Strut or Shock Absorber Leak Assessments

of products generally available in the North American market that meet the Volkswagen Oil Quality Standard

installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. This document also contains advice on the installation of these devices

*PE

VEHICLES AFFECTED BY THIS ACTION MAY HAVE IGNITION COILS THAT COULD MALFUNCTION UNDER CERTAIN CONDITIONS. MODELS PASSAT AND WAGON; GOLF; GTI; JETTA AND WAGON; NEW BEETLE AND CONVERTIBLE; PHAETON; EOS; RABBIT, ETC. *PE

THE MISFIRE CONDITION MAY BE CAUSED BY A MALFUNCTIONING IGNITION COIL. VEHICLES ARE OUT OF PRODUCTION. *PE

TENSION IN DRIVETRAIN; VIBRATION AND LOAD SENSITIVE KNOCKING FROM THE DRIVETRAIN; CRACKING NOISE UPON ACCELERATION FROM STOP, WHILE CORNERING OR DRIVING SLOWLY; SHUDDER WHEN CORNERING; RUBBING OR SLIPPING WHEN CORNERING; ELECTRONIC FAULTS IN 22 FOUR WHEEL DRIVE ELECTRONICS-DTC'S 02033, 02039, 02042 OR 02400 STORED. *PE

Removal of Behr Flush Kit. VAS 6337/1A

Also includes 2018-2020 Tiguan LWB

necessary to have a car up and running

necessary to have a car up and running

numbers going forward.

re-used

are necessary to have a car up and running

AND SUBSEQUENT DIAGNOSTIC DIRECTION.

time units during the system update posted on July 4th.

Update model and model year applicability.

Updates include corrected diagnostic test plans for the stated vehicles.

Introducing new coolant type.

Introducing new coolant type.

Updates include corrected diagnostic test plans for the stated vehicles.

Also includes R32 2002-2007 and 2002-2006 Jetta Wagon.

customer concerns about a vehicle

customer concerns about a vehicle

Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated

The latest corresponding technical bulletins that address the issues, and concerns that have been had with the vehicles.

requests.

Update model year applicability.

Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated

customer concerns about a vehicle

(SVM) software update for any Technical Bulletin (TSB) / Required Vehicle Update (RVU).

the scan tool can lock up at 33%. The document informs how to service this issue

customer concerns about a vehicle

plug, the following steps need to be performed in order to enable the system.

If roll pin is sticking out on either side (as shown below), do not replace key. Instead, use appropriate sized punch and hammer to drive in the roll pin so that it is flush with edge of mechanism.

Simply adding fuel without completing a road test may not allow fault to clear.

Simply adding fuel without completing a road test may not allow fault to clear.

P310B), check the fuel pressure with BOTH a mechanical gauge and by the display in Measured Value Block 103. The readings should be 1 bar higher in the MVB due to reading atmospheric pressure + fuel pressure. If the mechanical gauge reading is within specification BUT the MVB 103 reading is not 1 bar higher, check for a possible faulty G410 Low Fuel Pressure sensor.

If the auxiliary battery (in the rear) is low on charge, it can set glow plug DTCs. The auxiliary battery is the battery that powers the glow plugs up during start-up.

Updated to include additional model year applicability.

-623- after repair.

ADDED EFB to "Select correct battery type" in bottom box. Also Jetta Wagon 2005 and 2018-2020 Tiguan LWB.

Updated to include model year 2019 applicability.

updates, and technical bulletins.

diagnosing Access/start fault 00183, be aware that the fault can indicate a concern with either the R138 Interior Access/Start Authorization Antenna 1 or the R137 Luggage Compartment Access/Start Authorization Antenna. This document informs of the recommended normal Guided Fault Finding.

updates, and technical bulletins.

diagnosing Access/start fault 00183, be aware that the fault can indicate a concern with either the R138 Interior Access/Start Authorization Antenna 1 or the R137 Luggage Compartment Access/Start Authorization Antenna. This document informs of the recommended normal Guided Fault Finding.

bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.

infomedia icons grayed out, workshop equipment tool storage application, technical bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.

VOLKSWAGEN created a method for a temporary workaround. The document is its procedure

If the auxiliary battery (in the rear) is low on charge, it can set glow plug DTCs. The auxiliary battery is the battery that powers the glow plugs up during start-up.

is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting the test plan through GFF or through Vehicle Self Diagnosis in adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.

conditioning system component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. This document contains information on how to diagnose, and service this issue.

P1250 "Fuel Level Too Low", add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear.

Charger

component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. Debris can be dispersed throughout the refrigerant circuit after a/c component damage. In order to maintain A/C operating efficiency, it is important to flush the refrigerant circuit after A/C component repairs.

is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting guided function of either the J393 or J519 or control module OBD of J393 or J519 then selecting adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.

*JS

TERMINAL 15 RELAY ACTIVATION CAN BE CHECKED IN MEASURED VALUE BLOCKS FOR MODULE THAT CONTROLS RELAY, AND J519 VEHICLE ELECTRICAL SYSTEM CONTROL MODULE. MEASURED VALUE BLOCK NUMBER VARIES BETWEEN VEHICLES. ALL 2006 MODELS EXCEPT ROUTAN. *PE

THE ECM RESULTING IN A READING THAT IS OUT OF TOLERANCE. *PE

IF THIS HAPPENS, THE MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATED TO LET YOU KNOW THAT VEHICLE MAY EXPERIENCE SOME DETERIORATION IN PERFORMANCE. IN SOME CASES, A MALFUNCTIONING IGNITION COIL MAY CAUSE A VEHICLE TO EXCEED FEDERAL AND/OR CALIFORNIA EMISSIONS STANDARDS. 2001-2007 PASSA/PASSAT WAGON. *PE UPDATED 8/9/10. *PE UPDATED 11/8/10. *PE UPDATED 12/8/10. *PE UPDATED 2/28/11. *PE UPDATED 3/21/11. *PE

IF THIS HAPPENS, THE MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATED TO LET YOU KNOW THAT THE VEHICLE MAY EXPERIENCE SOME DETERIORATION IN PERFORMANCE. IN SOME CASES, A MALFUNCTIONING IGNITION COIL MAY CAUSE A VEHICLE TO EXCEED FEDERAL AND/OR CALIFORNIA EMISSIONS STANDARDS. NO MODELS LISTED. *PE

DUE TO FUEL INTRUSION INTO THE LOW PRESSURE SIDE FUEL PRESSURE SENSOR-G410, A FALSE SIGNAL MAY BE SENT TO THE ECM RESULTING IN A READING THAT IS OUT OF TOLERANCE. *PE

SYMPTOMS CAN BE POOR HEAT, NO COOLING, OR INSUFFICIENT COOLING. *PE

MIL ON AND DTC P310B AND/OR P129F STORED IN THE ECM FAULT MEMORY. A MALFUCTION OF FUEL PRESSURE SENSOR-G410 (LOW PRESSURE SIDE) MAY CAUSE AN INCORRECT FUEL PRESSURE READING FROM THE ECM. THIS CONDITION MAY RESULT IN MIL ILLUMINATION AND DTC'S STORED IN FAULT MEMORY. *PE

LOCATE SPLICE TO DETERMINE POSSIBLE CORROSION. REPAIR WIRING AS PER REPAIR MANUAL. *PE

A MALFUNCTION OF FUEL PRESSURE SENSOR-G410-(LOW PRESSURE SIDE) MAY CAUSE AN INCORRECT FUEL PRESSURE READING FROM THE ECM. MAY RESULT IN MIL ILLUMINATION AND DTC'S STORED IN FAULT MEMORY. *PE

If original microswitch is not available, microswitch part number 1J5 962 104 B should be ordered and installed.

TB updated to include model year 2019 applicability.

827 566L, the microswitch from the original handle must be transferred to the new handle. If original microswitch is not available, microswitch part number 1J5 962 104 B should be ordered and installed.

lights, turn signals) are vented and may collect moisture on their inner surfaces, depending on humidity and other climatic changes. This document discusses necessary to diagnosis, and potential remedy of the issue.

discussed in this document

droplets visible on inside of exterior light lenses. The document also informs how to service the issue.

BULB(S) LIMITED EXTENSION WARRANTY. MODELS 2004-2007 TOUAREG. *PE

with swirl marks and or fine scratches from polishing or cleaning. This document informs of how the Finish can be significantly improved without the use of harsh polishing compounds and high speed buffing.

with swirl marks and or fine scratches from polishing or cleaning. This document informs of how the Finish can be significantly improved without the use of harsh polishing compounds and high speed buffing.

applications developed to repair concerns of squeaks, rattles, noise and trim fit conditions.

This document contains information on how to diagnose, and service this issue. This document also gives examples on filling out a claim form for the service.

To avoid unnecessary replacement of wiper blades, the condition and cleanliness of the windshield, rear window and wiper blades, should be checked first. This document contains information on how to diagnose, and service this issue.

meter to check for 0 V, which will be present after the open in the grid line. This document informs of how to diagnose the issue and tips on servicing the issue

with swirl marks and or fine scratches from polishing or cleaning. The document also have infromation about where to find warrenty coverage for the service

finish that completes the image of a clean (new) vehicle. This document informs that The use of non-water based products will increase the risk of causing damage to painted surfaces. The document also gives graphical examples of the dame that can occur if non-water based products are used.

*KB

However, aftermarket devices (i.e., drive data recorders) that connect to the DLC have now become available.

There are recommendations to use top tier gasoline retailers

REVISED PROCEDURE DEVELOPED TO TEST EVAP SYSTEM WITHOUT FUEL CAP. *JS

the rear suspension for any play in the bushing.

This document also applies to the 2004 Touareg.

and then braking?, be sure to check the lower outboard control arm in the rear suspension for any play in the bushing. The noise could be mistaken for a differential noise if using chassis ears, because of the noise transferring through the rear axle.

and then braking?, be sure to check the lower outboard control arm in the rear suspension for any play in the bushing. The noise could be mistaken for a differential noise if using chassis ears, because of the noise transferring through the rear axle.

corresponding cars and their Transmission Control Module complaint issues.

corresponding cars and their Transmission Control Module complaint issues.

INSTRUMENT CLUSTER LIGHT WOULD BE ON OR FLASHING. *PE

*RM

HEAT SHIELDS ARE TO BE INSPECTED AFTER COMPLETION O ANY TYPE OF REPAIR TO THE UNDERBODY (EXHAUST SYSTEM TRANSMISSION, ETC.), AND IF DAMAGED, REPLACED. *PE

*KB

CUSTOMER STATES TRANSMISSION SEEMS TO UPSHIFT TOO SOON OR TOO OFTEN. *TT

CUSTOMER STATES TRANSMISSION SEEMS TO UPSHIFT TOO SOON, OR TOO OFTEN. *TT

If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.

If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.

to a red order and check the ?Car Down? box to escalate the order. This document informs how to contact VWGoA Parts Specialist for help.

to a red order and check the ?Car Down? box to escalate the order. This document informs how to contact VWGoA Parts Specialist for help.

receives a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased"

receives a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased

A hard wired internet connection is also recommended.

The vehicle must be equipped with the RCD 310 or RCD 510 (Premium 8) radios or the RNS 510 or RNS 315 navigation systems. The Bluetooth system must be either the UHV low (9W2), UHV?NAR (9W7 or 9ZR) factory installed systems or the Volk ? L dealer installed system.

This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.

be displayed in place of the odometer. The high beam indicator may be flashing in the instrument cluster as well. This indicates the cluster is in Production mode. Production mode is not the same as ?Transport? mode. This document infroms of the difference between Production, and Transport mode.

setting when it is displayed in the instrument cluster.

hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.

Updated to include additional model and model year applicability.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC? III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN? Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Condensation is a normal characteristic in all A/C systems. If odor is noticeable continue to follow this document. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC? III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN? Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. This document contains information on how to diagnose, and service this issue.

There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Always use a water based product.

*NJ

*KB

UPDATE TO EXISTING TECHNICAL BULLETIN. NO PRODUCTION CHANGE REQUIRED. ALL MODELS. *PE

SUPERSEDES 0402 DATED DECEMBER 20, 2004. *TT