2007 Volkswagen Tiguan TSBs
140 Technical Service Bulletins across 14 categories
Categories
Software & Calibration
34 bulletinsODIS Service Update
Software Version Management
In SAGA, the time units for the Volkswagen DoubleCheck labor operation were reduced in error from 50 time units to 30...
Read full bulletin
time units during the system update posted on July 4th.
Quick Reference Update Guide
Update model year applicability to include 2023.
Update warranty table labor operation numbers due to recent Saga updates.
This bulletin contains general instructions for software updates.
Update Top Tier brochure part number.
Metadata update (add MY 2014 Eos (missing).
Updated to include additional models and model year applicability.
Update to Volkswagen Identifying and mixing of coolant.
Read full bulletin
Introducing new coolant type.
Update to mode; and model year applicability.
Update vehicle metadata to include pull ahead models.
Read full bulletin
Also includes R32 2002-2007 and 2002-2006 Jetta Wagon.
Instrument cluster production mode solution, updated to include additional model and model year applicability.
Update brochure part number, literature ordering websie address and include an additional model year applicability
Updated to include model year 2014 thru 2018 applicability.
Quick Reference Update Guide: This document informs of the corresponding software/hardware and disc availability to the...
Read full bulletin
customer concerns about a vehicle
Update brochure part number, literature ordering websie address and include an additional model year applicability
Updated to include model year 2014 thru 2018 applicability.
Quick Reference Update Guide: This document informs of the corresponding software/hardware and disc availability to the...
Read full bulletin
customer concerns about a vehicle
Update content and include additional models and model year applicability.
Quick Reference of vehicle concerns.
Read full bulletin
Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated
Quick Reference Update Guide of the vehicles expected upgraded software level.
Read full bulletin
The latest corresponding technical bulletins that address the issues, and concerns that have been had with the vehicles.
This communication is to update our ProFi dealers of the current status of the latest inbound and outbound ProFi...
Read full bulletin
requests.
Data Link connector pin assignment chart that is applicable to all models.
Read full bulletin
Update model year applicability.
Quick Reference of vehicle concerns.
Read full bulletin
Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated
Updated to include additional model year applicability.
Update to include additional model year applicability.
Update model year applicability.
Update to model year applicability.
Update model year applicability to include 2017.
Update model and model year applicability.
Quick Reference Update Guide: This document informs of the corresponding software/hardware and disc availability to the...
Read full bulletin
customer concerns about a vehicle
Quick Reference Update Guide: This document informs of the corresponding software/hardware and disc availability to the...
Read full bulletin
customer concerns about a vehicle
Other
31 bulletinsAntenna Diagnosis Overview
Damage to Data Link Connector (DLC) from Aftermarket Devices (Cannot Communicate with Vehicle OBD System)
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
VW Elsa Newsletter
Squeaks, Rattles, Noise, Repair Materials
Antenna Diagnosis Overview
When diagnosing fault code P2279-Leaking Air in Intake System, be sure to check the cam timing first.
Contacting the parts helpline
Part ordering
Tool number added to table.
Read full bulletin
Removal of Behr Flush Kit. VAS 6337/1A
Include new special tool adapter and 2018 model year Jetta only
The part number listed in the document is to be returned if it meets the criteria provided.
Trailer towing information
VAS 6154 Replacement Part Setup Guide
Trailer towing information
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part...
Read full bulletin
numbers going forward.
To include an additional model year applicability.
This information bulletin contains instructions for checking the pins/terminals for contacts and nano contacts.
Reminder for dealers to reference the repair manual and replace all necessary fasteners (bolts, nuts) that cannot be...
Read full bulletin
re-used
Tech Tips Damage to Data Link Connector (DLC) from Aftermarket Devices (Cannot Communicate with Vehicle OBD System)
Engine
23 bulletinsEngine Oils Which Meet Volkswagen Oil Quality Standard VW 502 00/505 00/505 01 and VW 504 00/507 00
Oil Consumption Measurement
Oil Consumption Measurement
Oil Consumption Measurement
Fuel Additive to Help Prevent Sporadic Misfire Faults
Fuel Additive to Help Prevent Sporadic Misfire Faults
Fuel Additive to Help Prevent Sporadic Misfire Faults
Fuel Additive to Help Prevent Sporadic Misfire Faults
Update to Volkswagen engine oil standards
To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line.
Read full bulletin
The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage. Proceed with checking any other lines as necessary. Once the damaged line is identified, repair utilizing the Repair kit by Permatex ITEM 09117.
Incorrect torque converter or flywheel/flexplate installation can result in transmission damage.
Read full bulletin
When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121).
If mechanical damage is found to the turbocharger (e.g.
Read full bulletin
damaged compression wheel, loose or broken shaft), it is not enough to just replace the turbocharger.
When diagnosis on the above engine leads to the testing of the N75, please refer to the picture below.
Read full bulletin
The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not.
Volkswagen Engine oil quality standards, update to attachments.
Fuel Additive to Help Prevent Sporadic Misfire Faults
Fuel additive to help prevent sporadic misfire faults.
Engine oil quality standards, update to attachments.
Update to Volkswagen engine oil specification attachments.
Engine oil quality standards.
Read full bulletin
Also includes all models for 1997-2003. Also Rabbit from 2006-2009.
Engine Oils Which Meet Volkswagen Oil Quality Standards
Gasoline Engine Misfire Diagnosis document
Tech Tips (Equipped with Turbocharged Engine Turbocharger Replacement Tip): If mechanical damage is found to the turbocharger (e.g.
Read full bulletin
damaged compression wheel, loose or broken shaft), it is not enough to just replace the turbocharger. This document informs the procedure of checks for damage.
Technical Bulletin (Oil Consumption Measurement): Customer states oil consumption is higher than the Volkswagen oil...
Read full bulletin
consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owners Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Further factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Electrical
15 bulletinsElectric Coolant Fans Continue to Run after Ignition is Switched OFF
Electric Coolant Fans Continue to Run after Ignition is OFF
Electric Coolant Fans Continue to Run after Ignition is OFF
P0102, P1128, P1296 - WA front oxygen sensor faults
Battery, Testing and Charging Using Midtronics VAS6161, MCR340V, InCharge 940, or GRX3000 Charger
Air Conditioning, Cleaning of the Refrigerant Circuit (U.S.Only)
If key blade is found to stick or bind when opening or closing, check position of roll pin that secures key blade to mechanism.
Read full bulletin
If roll pin is sticking out on either side (as shown below), do not replace key. Instead, use appropriate sized punch and hammer to drive in the roll pin so that it is flush with edge of mechanism.
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles.
Read full bulletin
Simply adding fuel without completing a road test may not allow fault to clear.
To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles.
Read full bulletin
Simply adding fuel without completing a road test may not allow fault to clear.
Electric coolant fans continue to run after ignition is switched off.
Battery testing and charging using special tools VAS6161 & GRX3000VAS Charger.
Read full bulletin
Updated to include additional model year applicability.
Explanation of error message received from scan tool when erasing diagnostic trouble codes (DTCs) in Control Module...
Read full bulletin
-623- after repair.
Battery Testing and Charging instruction.
Read full bulletin
Updated to include model year 2019 applicability.
This document contains the VW Elsa Newsletter that contains a general overview of wiring diagrams updates, technical...
Read full bulletin
bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.
This document contains the VW Elsa Newsletter that contains a general overview of wiring diagrams updates, ElsaPro...
Read full bulletin
infomedia icons grayed out, workshop equipment tool storage application, technical bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.
Pre-Delivery & Maintenance
8 bulletinsPerfect Delivery Inspection (PDI) - Technician and Detailer Inspections
Perfect Delivery Inspection (PDI) - Technician and Detailer Inspections
Perfect Delivery Inspection (PDI) - Technician and Detailer Inspections
Volkswagen Warranty Policies and Procedures ? April 2014
If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order.
Read full bulletin
If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.
If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order.
Read full bulletin
If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.
Tiguan Perfect Delivery Inspection (PDI) - Technician and Detailer Inspections: A checklist to insure a customer...
Read full bulletin
receives a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased
TIGUAN Perfect Delivery Inspection (PDI) - Technician and Detailer Inspections: A checklist to insure a customer...
Read full bulletin
receives a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased
Infotainment
5 bulletinsAll Vehicles with Bluetooth Phone Kit Installed ? Streaming Audio from Phone to Radio
When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off.
Read full bulletin
A hard wired internet connection is also recommended.
The streaming music feature on vehicles equipped with factory or dealer installed Bluetooth will be available only in certain instances.
Read full bulletin
The vehicle must be equipped with the RCD 310 or RCD 510 (Premium 8) radios or the RNS 510 or RNS 315 navigation systems. The Bluetooth system must be either the UHV low (9W2), UHV?NAR (9W7 or 9ZR) factory installed systems or the Volk ? L dealer installed system.
Alternative method for radio code retrieval.
Tech Tips (Instrument Cluster Production Mode): During PDI, or after installation of a replacement cluster, ?Pro? may...
Read full bulletin
be displayed in place of the odometer. The high beam indicator may be flashing in the instrument cluster as well. This indicates the cluster is in Production mode. Production mode is not the same as ?Transport? mode. This document infroms of the difference between Production, and Transport mode.
HVAC & Climate
5 bulletinsHVAC, Unpleasant Odor
HVAC, Unpleasant Odor
HVAC, Unpleasant Odor
DIRECTION TO PERFORM SYSTEM RESET AFTER COMPONENT REPLACMENT OR DISCONNECT OF THE HVAC SYSTEM CONTROL HEAD.
Read full bulletin
NO TEST PLAN INFORMATION TO ADDRESS THIS.
DIRECTION TO PERFORM SYSTEM RESET AFTER COMPONENT REPLACMENT OR DISCONNECT OF THE HVAC SYSTEM CONTROL HEAD.
Read full bulletin
NO TEST PLAN INFORMATION TO ADDRESS THIS.
Fuel System
4 bulletinsGasoline Quality
The DLC is intended for use with diagnostic scan tools and by emissions testing stations.
Read full bulletin
However, aftermarket devices (i.e., drive data recorders) that connect to the DLC have now become available.
For customer concern regarding ?fuel door will not open?, perform the following
Gasoline quality.
Lighting
4 bulletinsExterior Lights, Moisture Accumulation
Exterior Lights, Moisture Accumulation
Exterior Lights, Moisture Accumulation
Condensation and or water droplets visible on inside of exterior light lenses.
Read full bulletin
TB updated to include model year 2019 applicability.
Brakes
4 bulletinsIf, after replacement of the steering rack, fault code 01309 008 is set in the ABS/ESP module only, follow the test plan...
Read full bulletin
in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the direction below using Vehicle Self Diagnosis in Address Word 44 - Steering Assistance
Strut or Shock Absorber Leak Assesment.
Tech Tips (Electro - Steering issues): If, after replacement of the steering rack, fault code 01309 008 is set in the...
Read full bulletin
ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document
Tech Tips (Electro ? Steering - DTC 01309 008 ?No Communication with -J500-? is Stored in the ABS/ESP Module Only): ...
Read full bulletin
This document informs If, after replacement of the steering rack, fault code 01309 008 is set in the ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document using Vehicle Self Diagnosis in Address Word 44 - Steering Assistance:
Transmission
4 bulletinsWhen diagnosing a generator charging concern, it is recommended to verify operation of the one way clutch located in the...
Read full bulletin
generator pulley (if equipped) before replacing generator assembly. To check the one way clutch, remove the belt from the generator pulley and use a trim removal tool to hold fan blades inside generator, as shown below. When attempting to turn pulley by hand with fan blades held, pulley should spin freely in only one direction. If pulley spins freely in both directions, the one way clutch has failed and should be replaced before continuing diagnosis.
Addressing Transmission Fluid Temperature Sensor Concerns, update authing system metadata.
Addressing Transmission Fluid Temperature Sensor Concerns, update authing system metadata.
Tech Tips: Generator Charging Concern Diagnosis Tip - One Way Clutch Pulley Testing
Tires & Wheels
1 bulletinThe use of tire dressing gives your tires that shiny finish that completes the image of a clean (new) vehicle.
Read full bulletin
There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Always use a water based product.
Air Bags & Safety
1 bulletinAirbag Issues.
Body & Paint
1 bulletinexplaination of cross car distorion when looking through the windshield and how the "effect" in normal.