2009 Volkswagen Gti TSBs

This extension includes 2008-2015 GTI and Golf R*, 2012-2013 VW Beetle*, 2009 VW Jetta SportWagen*, 2013 VW Jetta Sedan and GLI*, 2009-2016 VW Eos*, 2008-2010 VW Passat*, 2009-2017 VW CC*, 2009-2018 VW Tiguan*, Certain model year 2015-2018 VW Golf*, 2015-2021 VW GTI*, 2015-2019 VW Golf R*, 2015-2019 VW Golf SportWagen and Alltrack*, 2019-2024 VW Jetta GLI*, 2019-2021 VW Arteon*, 2018-2023 VW Atlas*, and 2020-2023 VW Atlas Cross Sport*

Only)

Vehicles Registered in the State of Minnesota Only (US Dealers

Engine may run rough, and or MIL-ON with DTC P0087-low fuel pressure stored in ECM Fault Memory.

The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage. Proceed with checking any other lines as necessary. Once the damaged line is identified, repair utilizing the Repair kit by Permatex ITEM 09117.

vehicles of various model-years and engine/transmission combinations.

certain 2009-2015 MY Volkswagen TDI Clean Diesel Engine vehicles registered in the State of Minnesota only will receive a communication in July 2014 regarding the use of biodiesel fuel blends in their vehicles.

vibration damper (harmonic balancer) and the crankshaft timing chain sprocket to the crankshaft. Once the damper is removed, the crankshaft should not be rotated unless special tool spacer T10368 has been installed. The crankshaft timing chain sprocket and spur gear drive on the crankshaft have a coupling that must be seated correctly during assembly. Failure to install special tool spacer T10368 before rotating engine will cause the engine to skip time and bend valves.

When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121).

The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not.

?Adapt keys? test plan will not allow the new keys to adapt to the vehicle. Instead, perform the test plan for ?New identity?. During this test plan, make the appropriate selection to indicate only the lock set has been replaced, as shown below in figures 1 and 2.

(excludes Routan & ID.4)

(excludes Routan & ID.4)

(excludes Routan & ID.4)

(excludes Routan & ID.4)

Update to model year applicability.

Update to attachments.

Update procedure and work sheet.

Updated to include additional model and model year applicability.

exterior paint finish.

Also includes 2004 and 2005 Jetta Wagon and 2018-2020 Tiguan LWB

Also includes all models for 1997-2003. Also Rabbit from 2006-2009.

valve for Intake Manifold Flap

new -N316- valve has 3 hose ports rather than 2 (See Figure 1), requiring a fresh air line be installed during intake manifold replacement. This fresh air line will prevent dirt and debris from contaminating the -N316- solenoid.

should hold vacuum and which ones should not for diagnosis on the Vehicles with 2.0T Gasoline Engine (Engine Codes BPY, CCTA, CBFA) to the testing of the N75

and underside of hood may not match the exterior paint color of the vehicle. Depending on vehicle model and production plant, the color of the engine compartment and underside hood may not match the vehicle body color. This document informs dealers to let their customers know that these body surfaces (engine compartment and underside of hood) are not directly visible (exposed) and therefore do not require the same finish as visible, exterior surfaces.

? After pressing the clutch pedal, it remains on the floor. Due to mis-diagnosis of clutch systems, and to prevent incorrect parts replacement, diagnostic procedure implemented into guided fault finding. This document is meant to inform.

rattling noise from engine or exhaust area while accelerating from 1800-3000 RPM. In order to complete proper diagnosis and ensure that the noise is coming from the turbocharger use the procedure in this document.

is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications.

oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. This document informs how to test the oil consumption rate

diagnosing fault code P2279-Leaking Air in Intake System, be sure to check the cam timing first. This document informs how to check the cam timing

Vehicles with 2.0 TFSI Engine): As part of Volkswagen?s ongoing commitment to our environment, and in cooperation with the United States Environmental Protection Agency and the California Air Resources Board, Volkswagen is informing customers of the decision to extend the customers Emissions Control Systems Warranty for the intake manifold and fuel injectors under specific conditions to 10 years or 120,000 miles, whichever occurs first.

should hold vacuum and which ones should not for diagnosis on the Vehicles with 2.0T Gasoline Engine (Engine Codes BPY, CCTA, CBFA) to the testing of the N75

? After pressing the clutch pedal, it remains on the floor. Due to mis-diagnosis of clutch systems, and to prevent incorrect parts replacement, diagnostic procedure implemented into guided fault finding. This document is meant to inform.

and underside of hood may not match the exterior paint color of the vehicle. Depending on vehicle model and production plant, the color of the engine compartment and underside hood may not match the vehicle body color. This document informs dealers to let their customers know that these body surfaces (engine compartment and underside of hood) are not directly visible (exposed) and therefore do not require the same finish as visible, exterior surfaces.

rattling noise from engine or exhaust area while accelerating from 1800-3000 RPM. In order to complete proper diagnosis and ensure that the noise is coming from the turbocharger use the procedure in this document.

is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications.

oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. This document informs how to test the oil consumption rate

Vehicles with 2.0 TFSI Engine): As part of Volkswagen?s ongoing commitment to our environment, and in cooperation with the United States Environmental Protection Agency and the California Air Resources Board, Volkswagen is informing customers of the decision to extend the customers Emissions Control Systems Warranty for the intake manifold and fuel injectors under specific conditions to 10 years or 120,000 miles, whichever occurs first.

fault code P2279-Leaking Air in Intake System, be sure to check the cam timing first. This document informs how to check the cam timing

Also includes the CPPA engine code labor operation and time units.

Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles

Pressure Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles.

damaged compression wheel, loose or broken shaft), it is not enough to just replace the turbocharger. This document informs the procedure of checks for damage.

consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. This document informs of oil consumption tests to check a vehicles performance.

Completing the GFF function test and performing a vacuum check on the Canister Purge Valve -N80- are essential to diagnose proper operation and to avoid unnecessary replacements. This document informs how to perform the Diagnosis check

case while performing diagnosis for a diesel particulate filter, manual transmission repair, or turbocharger concern, it is recommended to complete the related worksheet/check sheet before calling. This document informs where Worksheets/Check Sheets are available on ServiceNet.

engine leads to the testing of the N75, please refer this document with graphical aid. The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not. Turbocharger fault codes P0299 and P0234 can be diagnosed using this test.

consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owners Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Further factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

indicates that excessive misfiring has occurred. As a result, the ECM has turned off a fuel injector to prevent catalyst damage. To address this fault, diagnose and repair all misfire concerns that are present. Repairing the other faults will resolve the P130A.

The document contains a campaign data sheet that informs of a replacement campaign (Fuse (Plug-in Position F16)). The issue was that The F16 position fuse could fail prematurely due to possible degradation of the fuse?s coating material. If this happens, it could cause a partial loss (but not a complete failure) of vehicle lighting, including the loss of DRL illumination on one side of the vehicle, which in turn could render the vehicle less visible to other motorists and pedestrians during daylight hours. The corrective action of the campaign was to Replace the existing F16 position fuse with a new, optimized hard-coated fuse. The document also contains a FAQ of questions dealers may have.

If this happens, it could cause a partial loss (but not a complete failure) of vehicle lighting, including the loss of DRL illumination on one side of the vehicle, which in turn could render the vehicle less visible to other motorists and pedestrians during daylight hours. The corrective action taken was to Replace the existing F16 position fuse with a new, optimized hard-coated fuse. This document informs how to install the new fuse and how to make a claim for the work provided

If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this document can be performed. This document contains the procedure for the VW method to remove musty odors

content of deposit control additives may result in one or more of the following conditions: -Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. -Engine runs rough after cold start. -Excessive engine cranking time. -Stumbles while driving. -Rough engine idle. -Loss of engine performance. -Poor fuel economy. This document informs of the procedure for the vehicle if it is diagnoised with poor quality gas

This document informs on the procedure to remove the engine cover.

This document contains the fault codes necessary to check the warranty coverage for servicing this issue.

meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage.

It also contains the claim codes for warranty coverage

performance, efficiency and service life of the engine. The use of poor quality fuels may result in deposit build up on the fuel injectors and intake valves. This may result in a rough running condition, sporadic misfires, or cold start misfire faults storing in the ECM fault memory. This document informs a Volkswagen approved fuel additive is available to help remove and prevent deposits on fuel injectors and intake valves.

performance, efficiency and service life of the engine. The use of poor quality fuels may result in deposit build up on the fuel injectors and intake valves. This may result in a rough running condition, sporadic misfires, or cold start misfire faults storing in the ECM fault memory. A Volkswagen approved fuel additive is available to help remove and prevent deposits on fuel injectors and intake valves. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Repeat repairs must be carefully addressed to identify the root cause of the concern. If misfires are determined to be related to a specific component(s) (fuel injector, spark plug, ignition coil), replace only one defective component at a time and re-evaluate the concern

it is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications. The production solution to service this issue is that no production change is required.

Codes necessary to diagnosis, and potential remedy of issue. The diagnosis codes for checking warranty coverage for servicing the vehicle are also available

and prevent deposits on fuel injectors and intake valves.

Document contains examples of Strut or Shock Absorber Leak Assessments

of products generally available in the North American market that meet the Volkswagen Oil Quality Standard

The fault codes are written in the document. The product solution for this issue an Improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

The Production Solution to this issue was an improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Intake manifold causing fault codes to be stored in the ECM. The production solution improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

? After pressing the clutch pedal, it remains on the floor. Due to mis-diagnosis of clutch systems, and to prevent incorrect parts replacement, diagnostic procedure implemented into guided fault finding (GFF). This document is for identifying the issue for diagnosis.

installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. This document also contains advice on the installation of these devices

AN EXTENSION WARRANTY, WITH SPECIFIC CONDITIONS, 10 YRS OR 120,000 MILES,WHICHEVER IS FIRST, HAS BEEN ISSUED FOR EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS. MODEL 2008-2011. *PE

CANISTER PURGE VALVE N80 ARE ESSENTIAL TO DIAGNOSE PROPER OPERATION. MODEL 2009-14 ALL BUT ROUTAN. *PE

MODELS 2008-2014 EOS, GTI, BEETLE CONVERTIBLE, JETTA, CC, PASSAT, TIGUAN, BEETLE. *PE

DRIVING, MAY RUN ROUGH AND/OR MIL ON. ALL MODELS 2008-2013. *PE

ALSO INCLUDED MODEL BEETLE CONVERTIBLE MODEL YEARS 2008-2013 *JS

*JS

TO AVOID UNNECESSARY REPLACEMENTS, HIGH PRESSURE FUEL PUMP DIAGNOSIS TEST IS ESSENTIAL TO PROPER PUMP OPERATION. MODELS 2009-2013 TIGUAN, EOS CC, GTI, BEETLE, CONVERTIBLE, JETTA. *PE

ENGINE CRANK, NO START AFTER LONG PERIODS WITHOUT DRIVING. ENGINE MAY RUN ROUGH, AND OR MIL-ON WITH DTC P0087-LOW FUEL PRESSURE STORED IN ECM FAULT MEMORY. ALSO INCLUDED MODEL EOS YEAR 2013, MODEL GIT YEAR 2013, MODEL BEETLE COVERTIBLE YEAR 2009-2013. *JS UPDATED 7/10/13. *PE

SOMETIMES ENGINE MAY RUN ROUGHT AND/OR MIL ON. MODELS 2009-2013 TIGUAN, EOS, CC, GTI, BEETLE, JETTA. *PE

2008-13 ALL MODELS. *PE

STARTED, TIMING CHAIN KEEPS SLIPPING AND EXHAUST LIGHT COMES ON. *PE

MULTIPLE TROUBLE CODES POSSIBLY STORED. ALL MODELS 2008-2012. *RM

THE HEADLAMPS OR INSIDE LIGHTS INTERMITTENTLY DIM SLIGHTLY AT IDLE SPEED. AT IDLE SPEED THE ALTERNATOR VOLTAGE CAN FLUCTUATE, AS THE ALTERNATOR CANNOT FULLY COMPENSATE THE FLUCTUATIONS. GOLF & WAGON GTI, NEW BEETLE & CONVERTIBLE, EOS, JETTA & WAGON & SPORTWAGON, RABBIT, R32, TIGUAN. *PE

AT IDLE SPEED THE ALTERNATOR VOLTAGE CAN FLUCTUATE, AS THE ALTERNATOR CANNOT FULLY COMPENSATE THE FLUCTUATIONS. SOME ELECTRIC CONSUMERS COME ON IN CYCLES OR HAVE NO CONSTANT CURRENT CONSUMPTION, WHICH AMPLIFIES THIS EFFECT. THE LOAD CONDITION OF THE VEHICLE BATTERY CAN ALSO INFLUENCE THIS EFFECT. MODELS GOLF, GTI, NEW BEETLE & CONVERTIBLE, EOS, JETTA, WAGON, SPORTWAGEN, RABBIT, R32, GOLF WAGON, TIGUAN. *PE

WHEN REPAIRING AUTO LEVELING SYSTEM FOR FAULTS 01534 OR 01535, RANGE CONTROL ADJUSTMENT MOTOR FAILURE, IT IS NOT NECESSARY TO REPLACE HEADLIGHT ASSEMBLY. RANGE CONTROL ADJUSTMENT MOTORS ARE SERVICEABLE THROUGH ETKA. *PE

Removal of Behr Flush Kit. VAS 6337/1A

Also includes 2018-2020 Tiguan LWB

numbers going forward.

New info on coverage for consequential damages

Only superseded part numbers to be ordered going forward.

Only superseded part numbers to be ordered going forward.

re-used

clock is losing time.

AND SUBSEQUENT DIAGNOSTIC DIRECTION.

time units during the system update posted on July 4th.

solution in warranty table.

Update model and model year applicability.

Introducing new coolant type.

Introducing new coolant type.

Also includes R32 2002-2007 and 2002-2006 Jetta Wagon.

Models Except Routan ElsaWeb/Pro was updated on August 12, 2013 with the following Volkswagen DoubleCheck labor operations for all Volkswagen models except Routan. This document informs where in ElsaWeb/Pro this information can be located.

customer concerns about a vehicle

Models Except Routan ElsaWeb/Pro was updated on August 12, 2013 with the following Volkswagen DoubleCheck labor operations for all Volkswagen models except Routan. This document informs where in ElsaWeb/Pro this information can be located.

customer concerns about a vehicle

Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated

updated Takata part ordering process was sent to all dealers. We?ve closely monitored the impact of that communication and would like to address several emerging trends.

The latest corresponding technical bulletins that address the issues, and concerns that have been had with the vehicles.

requests.

Update model year applicability.

Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated

customer concerns about a vehicle

(SVM) software update for any Technical Bulletin (TSB) / Required Vehicle Update (RVU).

customer concerns about a vehicle

programming function: A software fix is needed to correct a test that is not reading any information from the battery data module (BDM) and will output:

Update Tool terminology

If roll pin is sticking out on either side (as shown below), do not replace key. Instead, use appropriate sized punch and hammer to drive in the roll pin so that it is flush with edge of mechanism.

The new harness may be equipped with an extra connector. If all connections are made correctly, then it is necessary to remove that connector and tape the exposed wires back into the harness. Be sure to tape tightly in order to provide a water-tight repair.

sensor located in the steering rack. These vehicles do not have a G85 in the steering column. To determine G85 location, check the J500 Power steering control module part number in the GFF printout. Do not use the part number on the steering rack for this check.

Simply adding fuel without completing a road test may not allow fault to clear.

Simply adding fuel without completing a road test may not allow fault to clear.

If damage is found to a label on either unit, be sure to note this on the repair order along with the reason the radio is being replaced.

Updated to include additional model year applicability.

Update to require 70amp minimum battery charger during procedure.

-623- after repair.

ADDED EFB to "Select correct battery type" in bottom box. Also Jetta Wagon 2005 and 2018-2020 Tiguan LWB.

Updated to include model year 2019 applicability.

updates, and technical bulletins.

updates, and technical bulletins.

bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.

infomedia icons grayed out, workshop equipment tool storage application, technical bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.

is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting the test plan through GFF or through Vehicle Self Diagnosis in adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.

models for any reason, it is necessary to replace the steering harness as well. The new harness may be equipped with an extra connector. If all connections are made correctly, then it is necessary to remove that connector and tape the exposed wires back into the harness. Be sure to tape tightly in order to provide a water-tight repair.

conditioning system component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. This document contains information on how to diagnose, and service this issue.

Ozone Reduction Catalyst Temperature Sensor, this fault refers to - G611- as Radiator Identification Sensor. If the radiator requires replacement on any above listed vehicle, the -G611- will be packaged separately within the radiator packaging. The new sensor will need to be bonded to the radiator.

speed sensor complaints

P1250 "Fuel Level Too Low", add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear.

Charger

sensor complaints.

component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. Debris can be dispersed throughout the refrigerant circuit after a/c component damage. In order to maintain A/C operating efficiency, it is important to flush the refrigerant circuit after A/C component repairs.

Steering ? G85 Location Identification Tip): Ths document informs of the location of the G85 steering sensor. The sensors expected settings, and which vehicles do not have this sensor for electromechanical power steering.

is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting guided function of either the J393 or J519 or control module OBD of J393 or J519 then selecting adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.

LOSS OF LIGHTING WILL RENDER VEHICLE LESS VISIBLE, DURING DAYLIGHT HOURS. MODEL 2009-2010 JETTA SEDAN, 2009 GTI. *PE

*JS

ONE OR MORE OF THE FOLLOWING CODES MAY BE STORED IN THE ECM FAULT MEMORY-LOW FUEL RAIL PRESSURE DETECTED; FUEL RAIL PRESSURE SENSOR CIRCUIT LOW. ASSISTANCE TO PROPERLY DIAGNOSE A FUEL PRESSURE SENSOR-G247-CONCERN. MODELS CC, EOS, PASSAT AND WAGON, GTI, (A5) JETTA, (A6) JETTA, TIGUAN. *PE

dealers to share with customers about the misfueling guard.

The black line is for fuel pressure supply and the blue line is for fuel pressure return. To verify correct line installation, remove the metal cover exposing the fuel pump flange assembly (generally under the rear seat). Refer to the ELSA Repair Manual for specific location. Check for raised arrows on the flange housing. The black line (Fuel Pressure Supply) attaches to the connection with the arrow pointing away from it. The blue line (fuel return) attaches to the connection with arrow pointing to it.

However, aftermarket devices (i.e., drive data recorders) that connect to the DLC have now become available.

essential to diagnose proper pump operation and to avoid unnecessary replacements. Guided fault finding provides a function test for the high pressure fuel pump. This test must be performed in order to properly diagnose the high pressure fuel pump. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

essential to diagnose proper pump operation and to avoid unnecessary replacements. Guided fault finding provides a function test for the high pressure fuel pump. This test must be performed in order to properly diagnose the high pressure fuel pump. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

essential to diagnose proper pump operation and to avoid unnecessary replacements. This document informs how to perform the diagnostic. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Completing the GFF high pressure pump function test is essential to diagnose proper pump operation and to avoid unnecessary replacements. This document contains the procedure to update the programming on the diagnostic hardware. This document contains the fault codes necessary to check the warranty coverage for servicing this issue.

essential to diagnose proper pump operation and to avoid unnecessary replacements

essential to diagnose proper pump operation and to avoid unnecessary replacements.

There are recommendations to use top tier gasoline retailers

The black line is for fuel pressure supply and the blue line is for fuel pressure return.

REVISED PROCEDURE DEVELOPED TO TEST EVAP SYSTEM WITHOUT FUEL CAP. *JS

THIS IS A FUEL PRESSURE CONCERN. *RM

If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.

If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.

tear, outside influence and factory defect.

to a red order and check the ?Car Down? box to escalate the order. This document informs how to contact VWGoA Parts Specialist for help.

tear, outside influence and factory defect.

to a red order and check the ?Car Down? box to escalate the order. This document informs how to contact VWGoA Parts Specialist for help.

New info on 10% maintenance intervals

a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased

and tear, outside influence or a factory issue. This document informs what is under coverage for wiper blade issues.

a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased

the production process or by external influences. This document discusses options for repairs covered under warranty, and methods to prevent damage.

A hard wired internet connection is also recommended.

satellites in the area of the concern. This can be accomplished by following the instruction in Technical Bulletin 2023490 Antenna Diagnosis Overview.

In order to switch the unit out of this mode, hold down the forward seek button, the back seek button, and the music button at the same time until the unit shuts down. Once the unit is powered back ?ON? the safeguard mode will be deactivated.

In order to switch the unit out of this mode, hold down the forward seek button, the back seek button, and the music button at the same time until the unit shuts down. Once the unit is powered back ?ON? the safeguard mode will be deactivated.

Follow the instructions below to pair the phone:

The vehicle must be equipped with the RCD 310 or RCD 510 (Premium 8) radios or the RNS 510 or RNS 315 navigation systems. The Bluetooth system must be either the UHV low (9W2), UHV?NAR (9W7 or 9ZR) factory installed systems or the Volk ? L dealer installed system.

This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.

the various Bluetooth systems by: ? Visual Identification ? PR Code ? Part Number

the various Bluetooth systems by: ? Visual Identification ? PR Code ? Part Number

be displayed in place of the odometer. The high beam indicator may be flashing in the instrument cluster as well. This indicates the cluster is in Production mode. Production mode is not the same as ?Transport? mode. This document infroms of the difference between Production, and Transport mode.

systems by: ? Visual Identification ? PR Code ? Part Number

setting when it is displayed in the instrument cluster.

hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.

be shipped in transportation safeguard mode and therefore will have no sound output. This document informs how to deactivate the safeguard mode.

NO DIRECTIONS TO ADDRESS THIS IN THE REPAIR MANUAL OR SCAN TOOL.

NO DIRECTIONS TO ADDRESS THIS IN THE REPAIR MANUAL OR SCAN TOOL.

Update model year applicability to include 2022.

TB updated to include model year 2019 applicability.

Experience Team has monitored the claims processed through the Carefree Maintenance (CFM) program from its inception. Their findings reveal that, in many cases, the first maintenance interval service (10K) has been claimed multiple times while subsequent maintenance interval services (20K and 30K), although being performed for the customer, have been submitted erroneously. It is crucial that Volkswagen of America receives accurate claim coding information regarding the Carefree Maintenance (CFM) Program. Accurate claim data enables Volkswagen to assist Dealers to improve their CFM penetration and customer return rates. In addition, it allows VWoA to assess the perceived benefits of the program to our customers. To assist Dealer Service Departments in determining the most appropriate service number and maintenance interval to use, Volkswagen has established the guidelines in this document.

TB updated to include model year 2019 applicability.

Experience Team has monitored the claims processed through the Carefree Maintenance (CFM) program from its inception. Their findings reveal that, in many cases, the first maintenance interval service (10K) has been claimed multiple times while subsequent maintenance interval services (20K and 30K), although being performed for the customer, have been submitted erroneously. It is crucial that Volkswagen of America receives accurate claim coding information regarding the Carefree Maintenance (CFM) Program. Accurate claim data enables Volkswagen to assist Dealers to improve their CFM penetration and customer return rates. In addition, it allows VWoA to assess the perceived benefits of the program to our customers. To assist Dealer Service Departments in determining the most appropriate service number and maintenance interval to use, Volkswagen has established the guidelines in this document.

TB updated to include model year 2019 applicability.

programming procedure in this document addresses the following concerns: ? Music skips at beginning of track. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

lights, turn signals) are vented and may collect moisture on their inner surfaces, depending on humidity and other climatic changes. This document discusses necessary to diagnosis, and potential remedy of the issue.

discussed in this document

droplets visible on inside of exterior light lenses. The document also informs how to service the issue.

WARRANTY EXTENSION FOR CENTER HIGH MOUNTED STOPLIGHT LIGHT EMITTING DIODES (LEDS). CSC LETTER WAS RECEIVED. *PE

Update to model year applicability and new warranty GFF labor operation number

Updated to include additional model and model year applicability.

To include additional models and model year applicability. A.C. Compressor Replacement, GFF Required Regardless of Concern and Flush Requirement

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC? III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN? Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Condensation is a normal characteristic in all A/C systems. If odor is noticeable continue to follow this document. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC? III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN? Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. This document contains information on how to diagnose, and service this issue.

NO TEST PLAN INFORMATION TO ADDRESS THIS.

NO TEST PLAN INFORMATION TO ADDRESS THIS.

FRESH AIR BLOWER RUNS ONLY AT HIGHEST LEVEL. BECAUSE OF PERMANENT FROST AND SNOWFALL FINE SNOW CAN GET INTO THE FRESH AIR BLOWER VIA THE AIR INTAKE. *PE

in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the direction below using Vehicle Self Diagnosis in Address Word 44 - Steering Assistance

proprietary ?Lightning? connector that is different than the 30-pin dock connector found on previous iPhone and iPad/iPod models.

that is different than the 30 pin dock connector found on previous iPhone and iPod models.

ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document

The Apple iPhone 5, iPhone 5c, and iPhone 5s, as well as the iPad 4th generation and iPod Nano 7th generation use a proprietary ?Lightning? connector that is different than the 30-pin dock connector found on previous iPhone and iPad/iPod models. A new MDI cable (?MDI Adapter Cable ? Lightning Charger?) is now available through the VW Accessories eCatalog that is made for use with iPhone 5 variants as well as the previously mentioned iPad/iPod models. This cable should provide full functionality on any vehicle equipped with a UMI (Unified Multimedia Interface). On MY 13 and older vehicles equipped with an MDI, the software level of the MDI must be at or above SW 240 (see Technical Bulletin 2024337) in order to be fully functional.

Volkswagen vehicles repaired by Safety Recall 45F2.

This document informs If, after replacement of the steering rack, fault code 01309 008 is set in the ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document using Vehicle Self Diagnosis in Address Word 44 - Steering Assistance:

AFTER REPLACING THE STEERING RACK THE FAULT CODE 01309 008 IS SET IN ABS/ESP MODULE. ALSO INCLUDED MODEL GTI MY 2013, MODEL TIGUAN MY 2005-2007, MODEL RABBIT MY 2005/2011-2013, MODEL EOS MY 2005/2013, MODEL CC MY 2005-2008*JS

with swirl marks and or fine scratches from polishing or cleaning. This document informs of how the Finish can be significantly improved without the use of harsh polishing compounds and high speed buffing.

with swirl marks and or fine scratches from polishing or cleaning. This document informs of how the Finish can be significantly improved without the use of harsh polishing compounds and high speed buffing.

applications developed to repair concerns of squeaks, rattles, noise and trim fit conditions.

To avoid unnecessary replacement of wiper blades, the condition and cleanliness of the windshield, rear window and wiper blades, should be checked first. This document contains information on how to diagnose, and service this issue.

This document contains Warranty information for coverage, and informs of methods to to service the issue

meter to check for 0 V, which will be present after the open in the grid line. This document informs of how to diagnose the issue and tips on servicing the issue

with swirl marks and or fine scratches from polishing or cleaning. The document also have infromation about where to find warrenty coverage for the service

It discusses how it can happen, and where to find warranty coverage to service the parts

finish that completes the image of a clean (new) vehicle. This document informs that The use of non-water based products will increase the risk of causing damage to painted surfaces. The document also gives graphical examples of the dame that can occur if non-water based products are used.

generator pulley (if equipped) before replacing generator assembly. To check the one way clutch, remove the belt from the generator pulley and use a trim removal tool to hold fan blades inside generator, as shown below. When attempting to turn pulley by hand with fan blades held, pulley should spin freely in only one direction. If pulley spins freely in both directions, the one way clutch has failed and should be replaced before continuing diagnosis.

This procedure is to be used ?After? the transmission has been removed from the vehicle.

plan "Read measured values for obligation to report" can be selected. This function will retrieve all of the MVBs from the transmission which can be attached to a VTA ticket. This selection is available under Guided Functions or GFF when using VAS-PC, an example is shown below.

TRANSMISSION

*RM

IN SOME VEHICLES IT IS POSSIBLE THAT A BUSHING INSIDE THE MECHATRONIC UNIT HAS THE POTENTIAL TO WEAR OUT PREMATURELY, CAUSING THE CLUTCHES INSIDE THE TRANSMISSION TO OPERATE LESS SMOOTHLY THAN BEFORE. THE DRIVER WILL BEGIN TO NOTICE CHANGES IN THE WAY THE VEHICLE FEELS AS THE TRANSMISSION SHIFTS (JERKING). THIS CHANGE CAN BECOME VERY PRONOUNCED, THE VEHICLE REMAINS SAFE TO DRIVE. *PE

SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. IN SOME VEHICLES IT IS POSSIBLE THAT A BUSHING INSIDE THE MECHATRONIC UNIT HAS THE POTENTIAL TO WEAR OUT PREMATURELY, CAUSING THE CLUTCHES INSIDE THE TRANSMISSION TO OPERATE LESS SMOOTHLY THAN BEFORE. *PE UPDATED 3/21/11. *PE

SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SOME VEHICLES IT IS POSSIBLE THAT A BUSHING INSIDE THE MECHATRONIC UNIT HAS THE POTENTIAL TO WEAR OUT PREMATURELY, CAUSING THE CLUTCHES INSIDE THE TRANSMISSION TO OPERATE LESS SMOOTHLY THAN BEFORE. JETTA, JETTA SPORTWAGEN/WAGON, GTI, R32, EOS. CSC LETTER WAS REC'D. *PE (LOANER CLARIFIED) UPDATED 3/21/11. *PE

HEAT SHIELDS ARE TO BE INSPECTED AFTER COMPLETION O ANY TYPE OF REPAIR TO THE UNDERBODY (EXHAUST SYSTEM TRANSMISSION, ETC.), AND IF DAMAGED, REPLACED. *PE

Update to model year applicability.

After this date, Takata allocations will be based on the previous week?s paid claim volume. It is CRITICAL that claims are submitted in a timely fashion in order to receive an appropriate volume of additional parts to support demand.

requested for return through the Warranty Parts Portal but will be requested for return through the Takata XPO Return Program.

UPDATE TO EXISTING TECHNICAL BULLETIN. NO PRODUCTION CHANGE REQUIRED. ALL MODELS. *PE

There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Always use a water based product.

Information only for all other dealers.

Also includes: 1998-2004 Beetle, 2003-2004 Beetle Convertible, 2019 Beetle Convertible, 1994-2004 Eurovan, 1994-2004 Golf, 1994-2004 Jetta, 2001-2004 Jetta Wagon, 2018-2019 Tiguan LWB, 1994-2004 Passat, 1994-2004 Passat Wagon, 2004 Phaeton, 2013-2016 Jetta Hybrid, 2004 R32 and 1995-2006 Cabrio.