2005 Volkswagen Golf TSBs

The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage. Proceed with checking any other lines as necessary. Once the damaged line is identified, repair utilizing the Repair kit by Permatex ITEM 09117.

This applies to Mechanical Injection Style Diesel Engines, Pumpe Duse Style Diesel Engines and the new Common Rail Style Diesel Engines.

When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121).

returned to idle.

damaged compression wheel, loose or broken shaft), it is not enough to just replace the turbocharger.

exterior paint finish.

Also includes 2004 and 2005 Jetta Wagon and 2018-2020 Tiguan LWB

Also includes all models for 1997-2003. Also Rabbit from 2006-2009.

and underside of hood may not match the exterior paint color of the vehicle. Depending on vehicle model and production plant, the color of the engine compartment and underside hood may not match the vehicle body color. This document informs dealers to let their customers know that these body surfaces (engine compartment and underside of hood) are not directly visible (exposed) and therefore do not require the same finish as visible, exterior surfaces.

is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications.

oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. This document informs how to test the oil consumption rate

and underside of hood may not match the exterior paint color of the vehicle. Depending on vehicle model and production plant, the color of the engine compartment and underside hood may not match the vehicle body color. This document informs dealers to let their customers know that these body surfaces (engine compartment and underside of hood) are not directly visible (exposed) and therefore do not require the same finish as visible, exterior surfaces.

is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications.

oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. This document informs how to test the oil consumption rate

standards lists to current specifications. Engine Oils Which Meet Volkswagen Oil Quality Standards

damaged compression wheel, loose or broken shaft), it is not enough to just replace the turbocharger. This document informs the procedure of checks for damage.

consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. This document informs of oil consumption tests to check a vehicles performance.

case while performing diagnosis for a diesel particulate filter, manual transmission repair, or turbocharger concern, it is recommended to complete the related worksheet/check sheet before calling. This document informs where Worksheets/Check Sheets are available on ServiceNet.

Solenoid Valve in the event of a turbocharger fault code such as P0299 or P0234. This applies to Mechanical Injection Style Diesel Engines, Pumpe Duse Style Diesel Engines and the new Common Rail Style Diesel Engines.

consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owners Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Further factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

if the vehicle is driven under load or revved up and then returned to idle. This document informs of what to do should these systems occur.

If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this document can be performed. This document contains the procedure for the VW method to remove musty odors

content of deposit control additives may result in one or more of the following conditions: -Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. -Engine runs rough after cold start. -Excessive engine cranking time. -Stumbles while driving. -Rough engine idle. -Loss of engine performance. -Poor fuel economy. This document informs of the procedure for the vehicle if it is diagnoised with poor quality gas

meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage.

down into the door, or the rear glass motor operates but the glass does not move. This document contains the fault codes, and procedure to service these issues

it is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications. The production solution to service this issue is that no production change is required.

glass may slide down into the door, or the rear glass motor operates but the glass does not move

of products generally available in the North American market that meet the Volkswagen Oil Quality Standard

installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. This document also contains advice on the installation of these devices

*PE

ENGINE SOFTWARE MAY CAUSE THE VEHICLE TO EXCEED EMISSIONS STANDARDS. *RM

VEHICLES AFFECTED BY THIS ACTION MAY HAVE IGNITION COILS THAT COULD MALFUNCTION UNDER CERTAIN CONDITIONS. MODELS PASSAT AND WAGON; GOLF; GTI; JETTA AND WAGON; NEW BEETLE AND CONVERTIBLE; PHAETON; EOS; RABBIT, ETC. *PE

SOFTWARE UPDATE AND NEW INJECTORS. INSTALLING NEW INJECTORS AND ENGINE CONTROL MODEL UPDATE-PROGRAMMING (FLASHING) USING SOFTWARE VERSION MANAGEMENT (SVM). MODELS GOLF, JETTA AND WAGON; NEW BEETLE. *PE

THE HEADLAMPS OR INSIDE LIGHTS INTERMITTENTLY DIM SLIGHTLY AT IDLE SPEED. AT IDLE SPEED THE ALTERNATOR VOLTAGE CAN FLUCTUATE, AS THE ALTERNATOR CANNOT FULLY COMPENSATE THE FLUCTUATIONS. GOLF & WAGON GTI, NEW BEETLE & CONVERTIBLE, EOS, JETTA & WAGON & SPORTWAGON, RABBIT, R32, TIGUAN. *PE

AT IDLE SPEED THE ALTERNATOR VOLTAGE CAN FLUCTUATE, AS THE ALTERNATOR CANNOT FULLY COMPENSATE THE FLUCTUATIONS. SOME ELECTRIC CONSUMERS COME ON IN CYCLES OR HAVE NO CONSTANT CURRENT CONSUMPTION, WHICH AMPLIFIES THIS EFFECT. THE LOAD CONDITION OF THE VEHICLE BATTERY CAN ALSO INFLUENCE THIS EFFECT. MODELS GOLF, GTI, NEW BEETLE & CONVERTIBLE, EOS, JETTA, WAGON, SPORTWAGEN, RABBIT, R32, GOLF WAGON, TIGUAN. *PE

THE EMISSIONS MONITORING SYSTEM CAN CAUSE AFFECTED VEHICLES TO EXCEED FEDERAL AND/OR CALIFORNIA EMISSIONS STANDARDS. INSPECT AND, IF NECESSARY, UPDATE THE ECM SOFTWARE. MODELS JETTA, JETTA WAGON, GOLF AND NEW BEETLE. *PE

CALIX. *TT

*TC

Removal of Behr Flush Kit. VAS 6337/1A

Also includes 2018-2020 Tiguan LWB

numbers going forward.

re-used

AND SUBSEQUENT DIAGNOSTIC DIRECTION.

*KB

*TT

*TT

time units during the system update posted on July 4th.

Updates include corrected diagnostic test plans for the stated vehicles.

Introducing new coolant type.

Introducing new coolant type.

Also includes R32 2002-2007 and 2002-2006 Jetta Wagon.

customer concerns about a vehicle

customer concerns about a vehicle

Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated

The latest corresponding technical bulletins that address the issues, and concerns that have been had with the vehicles.

requests.

Update model year applicability.

Includes a list of Software versions and the technical bulletin numbers that referred to the concerns Updated

customer concerns about a vehicle

(SVM) software update for any Technical Bulletin (TSB) / Required Vehicle Update (RVU).

customer concerns about a vehicle

If roll pin is sticking out on either side (as shown below), do not replace key. Instead, use appropriate sized punch and hammer to drive in the roll pin so that it is flush with edge of mechanism.

This can be accomplished by selecting the test plan through GFF or through Vehicle Self Diagnosis in adaptation channel 99.

Simply adding fuel without completing a road test may not allow fault to clear.

Simply adding fuel without completing a road test may not allow fault to clear.

Updated to include additional model year applicability.

ADDED EFB to "Select correct battery type" in bottom box. Also Jetta Wagon 2005 and 2018-2020 Tiguan LWB.

Updated to include model year 2019 applicability.

bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.

infomedia icons grayed out, workshop equipment tool storage application, technical bulletins, pending service solutions, tech tips, campaigns, updates, and suggestions.

is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting the test plan through GFF or through Vehicle Self Diagnosis in adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.

conditioning system component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. This document contains information on how to diagnose, and service this issue.

speed sensor complaints

P1250 "Fuel Level Too Low", add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear.

Charger

sensor complaints.

component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. Debris can be dispersed throughout the refrigerant circuit after a/c component damage. In order to maintain A/C operating efficiency, it is important to flush the refrigerant circuit after A/C component repairs.

is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting guided function of either the J393 or J519 or control module OBD of J393 or J519 then selecting adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.

*JS

IF THIS HAPPENS, THE MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATED TO LET YOU KNOW THAT VEHICLE MAY EXPERIENCE SOME DETERIORATION IN PERFORMANCE. IN SOME CASES, A MALFUNCTIONING IGNITION COIL MAY CAUSE A VEHICLE TO EXCEED FEDERAL AND/OR CALIFORNIA EMISSIONS STANDARDS. 2001-2007 PASSA/PASSAT WAGON. *PE UPDATED 8/9/10. *PE UPDATED 11/8/10. *PE UPDATED 12/8/10. *PE UPDATED 2/28/11. *PE UPDATED 3/21/11. *PE

IF THIS HAPPENS, THE MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATED TO LET YOU KNOW THAT THE VEHICLE MAY EXPERIENCE SOME DETERIORATION IN PERFORMANCE. IN SOME CASES, A MALFUNCTIONING IGNITION COIL MAY CAUSE A VEHICLE TO EXCEED FEDERAL AND/OR CALIFORNIA EMISSIONS STANDARDS. NO MODELS LISTED. *PE

REVISED EXPIRATION DATES FOR SEAT HEATER CUSTOMER SATISFACTION CAMPAIGNS. AFFECTED VEHICLES MAY HAVE A SEAT HEATER ELEMENT THAN CAN MALFUNCTION WHEN THE IGNITION SWITCH IS ON AND THE SEAT HEATER SWITCH IS ON. MODELS VV00 AND VZ00, M200 AND M300, AND R200 AND R300, EXTENDED TIL 6/30/10 (VV, VZ, M2, M3) AND 9/30/10 (R2 AND R3). CSC LETTERS HAS BEEN RECEIVED. *PE

INSTALL DRIVER'S SIDE HEATER REPAIR KIT. SEAT HEATER MAY MALFUNCTION WHEN THE IGNITION SWITCH IS ON. THIS COULD CAUSE THE HEATER MAT TO TEMPORARILY OVERHEAT AND BECOME INOPERATIVE. *KB

CUSTOMER SATISFACTION CAMPAIGN VZ. *TT

THE SEAT HEATER MAT MAY TEMPORARILY OVERHEAT AND BECOME INOPERATIVE. INSTALL NEW PASSENGER SIDE SEAT HEATER SWITCH. *TT UPDATED 08-21-07. *KB

CUSTOMER SATISFACTION CAMPAIGN VV. *TT

with swirl marks and or fine scratches from polishing or cleaning. This document informs of how the Finish can be significantly improved without the use of harsh polishing compounds and high speed buffing.

with swirl marks and or fine scratches from polishing or cleaning. This document informs of how the Finish can be significantly improved without the use of harsh polishing compounds and high speed buffing.

Supersedes TB V551603

applications developed to repair concerns of squeaks, rattles, noise and trim fit conditions.

extra seal and the Poly Vinyl Chloride (PVC) foil. This document contains information on how to diagnose, and service this issue. This document also gives examples on filling out a claim form for the service.

To avoid unnecessary replacement of wiper blades, the condition and cleanliness of the windshield, rear window and wiper blades, should be checked first. This document contains information on how to diagnose, and service this issue.

Corrosion under the door fold in the area of the extra seal and the Poly Vinyl Chloride (PVC) foil. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

meter to check for 0 V, which will be present after the open in the grid line. This document informs of how to diagnose the issue and tips on servicing the issue

Only) ): Document discusses diagnosis, and potential remedy of issue. The diagnosis codes for checking warranty coverage for servicing the vehicle are also available

The document also has example claim forms for repears. The diagnosis codes for checking warranty coverage for servicing the vehicle are also available

with swirl marks and or fine scratches from polishing or cleaning. The document also have infromation about where to find warrenty coverage for the service

It gives examples on where to check for repair coverage from warranties, fixing possible issues, and how to document the corrections

The corrosion may be found on this edge anywhere around the hood. It discusses how to service it, and document that service. It discusses where to find what applies to warranties that offer coverage for the service

Also gives examples of how to calculate cost to repair or replace

Corrosion, Front Fenders, at Upper Wheel Opening (U.S. Only)

finish that completes the image of a clean (new) vehicle. This document informs that The use of non-water based products will increase the risk of causing damage to painted surfaces. The document also gives graphical examples of the dame that can occur if non-water based products are used.

INSPECT, CLEAN AND MODIFY SUNROOF DRAINS FOR CERTAIN VOLKSWAGEN VEHICLES AND REVISED MAINTENANCE SCHEDULE; SUNROOF DRAIN INSPECTION AND CLEANING. NO MODELS OR MODEL YEARS LISTED. CSC LETTER WAS REC'D. *PE MODEL AND MODEL YEARS INCLUDED. UPDATED *PE

*KB

*JB

If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.

If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.

to a red order and check the ?Car Down? box to escalate the order. This document informs how to contact VWGoA Parts Specialist for help.

to a red order and check the ?Car Down? box to escalate the order. This document informs how to contact VWGoA Parts Specialist for help.

a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased

a wonderful delivery of a vehicle that looks, feels, and meets the expectations of a new vehicle that he/she has purchased

TB updated to include model year 2019 applicability.

lights, turn signals) are vented and may collect moisture on their inner surfaces, depending on humidity and other climatic changes. This document discusses necessary to diagnosis, and potential remedy of the issue.

discussed in this document

droplets visible on inside of exterior light lenses. The document also informs how to service the issue.

THIS MAY BE CAUSED BY INTAKE HOSES LEAKING (DURING BOOST CONDITIONS) DUE TO INCORRECT TORQUE ON CLAMPS OR IMPROPER PLACEMENT, WORN OR TORN INTAKE HOSES. *KB

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC? III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN? Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. Condensation is a normal characteristic in all A/C systems. If odor is noticeable continue to follow this document. Contaminants are effectively neutralized using the AIRCOMATIC? II Ultrasonic Climate System Cleaner (VAS 6189A) or AIRCOMATIC? III Ultrasonic Climate System Cleaner (VAS 6189B) and AIRCO-CLEAN? Ultrasonic HVAC Treatment (30208). All other cleaning methods are no longer permitted. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.

Odor mainly occurs after vehicle has been sitting (unused) at least 5 hours and within 20 to 60 seconds after vehicle is first started. This document contains information on how to diagnose, and service this issue.

THIS INCLUDE JETTA WAGON. *PE UPDATED 3/23/09. REVISION TO CUSTOMER SATISFACTION CAMPAIGNS FOR SEAT HEATERS. *PE UPDATED 3/17/10. *PE

*PE UPDATED 3/23/09. REVISION TO CUSTOMER SATISFACTION CAMPAIGN. *PE UPDATED 3/17/10. *PE

*TT

However, aftermarket devices (i.e., drive data recorders) that connect to the DLC have now become available.

There are recommendations to use top tier gasoline retailers

REVISED PROCEDURE DEVELOPED TO TEST EVAP SYSTEM WITHOUT FUEL CAP. *JS

*KB

*TT UPDATE. *TT UPDATE. *TT

A hard wired internet connection is also recommended.

The vehicle must be equipped with the RCD 310 or RCD 510 (Premium 8) radios or the RNS 510 or RNS 315 navigation systems. The Bluetooth system must be either the UHV low (9W2), UHV?NAR (9W7 or 9ZR) factory installed systems or the Volk ? L dealer installed system.

hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.

generator pulley (if equipped) before replacing generator assembly. To check the one way clutch, remove the belt from the generator pulley and use a trim removal tool to hold fan blades inside generator, as shown below. When attempting to turn pulley by hand with fan blades held, pulley should spin freely in only one direction. If pulley spins freely in both directions, the one way clutch has failed and should be replaced before continuing diagnosis.

of these transmissions, check ETKA to see if you must also replace the Transmission Control Module (TCM) at the same time. In some instances the new transmission will require an updated TCM.

*RM

HEAT SHIELDS ARE TO BE INSPECTED AFTER COMPLETION O ANY TYPE OF REPAIR TO THE UNDERBODY (EXHAUST SYSTEM TRANSMISSION, ETC.), AND IF DAMAGED, REPLACED. *PE

UPDATE TO EXISTING TECHNICAL BULLETIN. NO PRODUCTION CHANGE REQUIRED. ALL MODELS. *PE

There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Always use a water based product.

Also includes: 1998-2004 Beetle, 2003-2004 Beetle Convertible, 2019 Beetle Convertible, 1994-2004 Eurovan, 1994-2004 Golf, 1994-2004 Jetta, 2001-2004 Jetta Wagon, 2018-2019 Tiguan LWB, 1994-2004 Passat, 1994-2004 Passat Wagon, 2004 Phaeton, 2013-2016 Jetta Hybrid, 2004 R32 and 1995-2006 Cabrio.

The blend door control lever moves freely, but the blend door does not operate. A bushing that fits on the lever may have a broken tab/clip. This document discusses the potential remedy of the issue.