2012 Toyota Yaris TSBs

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

instrument panel and the windshield may come loose. Parts have been revised to address this condition.

source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.

quenching process during manufacturing.

On some vehicles, when Rapgard? is removed the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is NOT necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

THESE STAINS APPEAR TO BE UNDER THE CLEAR COAT (REPAINTING THIS AREA IS NOT NECESSARY). THE STAIN PATTERNS ARE USUALLY UNDER WRINKLES IN THE RAPGARD. THESE WRINKLES SOMETIMES TRAP WATER AND CAUSE THE PAINT TO STAIN FROM THE TRAPPED MOISTURE, ESPECIALLY ON HORIZONTAL SURFACES, SUCH AS THE HOOD, ROOF, AND TRUNK. STAINS CAN BE REMOVED BY HEATING THE STAINED SURFACE TO REMOVE THE TRAPPED MOISTURE.

Please see T-SB-0057-18.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0012-21.

Please see T-SB-0044-16.

Please see T-SB-0063-20.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0010-20.

Please see T-SB-0080-19.

The purpose of this Tech Tip is to clarify these models and to help you make the appropriate selection.

The purpose of this Tech Tip is to clarify these models and to help you make the appropriate selection.

Please see T-SB-0012-13.

Please see T-SB-0134-16.

Once the system is reset, all previously registered keys will be erased.

Once the system is reset, all previously registered keys will be erased.

Please see T-SB-0054-13.

10,000 miles for most vehicles that require this oil. With this change, the following should be noted

Please see T-SB-0185-13.

31, 2017 LSC Expired on December 31, 2017.

THE PURPOSE OF THIS TECH TIP IS TO CLARIFY THESE MODELS AND TO HELP YOU MAKE THE APPROPRIATE SELECTION.

THE PURPOSE OF THIS TECH TIP IS TO CLARIFY THESE MODELS AND TO HELP YOU MAKE THE APPROPRIATE SELECTION.

The settlement includes Toyota?s agreement to provide a Customer Support Program (?CSP?) for 2002-2019 model year (MY) vehicles originally equipped with certain Takata airbag inflators or repaired under a recall with Takata airbag inflators to provide coverage for repairs of the airbag inflator contained in the airbag module. This CSP letter is to help clarify how to administer this coverage in accordance with the settlement. This is NOT a recall or a campaign, but is provided to reassure owners that Toyota stands behind the reliability of our vehicles.

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN F0B OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR CERTAIN 2012 ? 2013 MODEL YEAR YARIS HATCHBACK.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

identification.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

are used to control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag. This LSC will be available until December 31, 2017, and will only be available at an authorized Toyota Dealer.

are used to control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

are used to control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag. This LSC will be available until December 31, 2017, and will only be available at an authorized Toyota Dealer.

are used to control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.

FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION."

*PE

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

pipe sub-assembly located at the top right of the engine compartment.

pipe sub-assembly located at the top right of the engine compartment.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

been disconnected or power to the Engine ECM has been interrupted.

power to the Engine ECM has been interrupted.

The drive belt (v-belt) tension specification has been updated to address this condition.

There a re man benefits of this oil.

Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.

There are multiple benefits of this oil including: Reduced friction and wear on engine surfaces, Improved fuel economy, Reduction in waste oil stream (in vehicles approved for 10,000 mile oil change intervals), Reduced maintenance cost (in vehicles approved for 10,000 mile oil change intervals). Due to the improved performance and durability of 0w20 synthetic oil, Toyota has extended the oil change intervals to 10,000 mile for most vehicles that require this oil. With this change, the following should be noted: The 2TR-FE (4Runner/Tacoma) and the 3UR-FBE (Flex Fuel Tundra/Sequoia) are the exceptions to this new change interval program; these engines have not been approved for the 10,000 mile interval at this time. A 5,000 mile oil change interval is still required for these vehicles. Also, the Flex Fuel 3UR-FBE requires a 2,500 mile interval when operated on E85 50% of the time or more. Only Toyota vehicles in which 0w20 oil is mandatory (except for the 2TR-FE & 3UR-FBE Engines) have been approved for extended oil change intervals. Vehicles in which 0w-20 is an option to 5w20 (or 5w30) will continue to require 5,000 mile change intervals, even if 0w20 oil is used. In case of vehicles with 10,000 mile oil change intervals, the 5,000 mile service interval has not been eliminated. The traditional 5,000 mile maintenance procedures (such as tire rotation) will continue to be required, and the fluid levels (including engine oil) will need to be checked and adjusted at this time. If the vehicle operation meets the standard criteria for "Special Operating Conditions" such as: driving off-road, on dirt roads, towing a trailer, making repeated short trips under 32 degrees F, or extensive idling, the engine oil must be replaced at 5,000 mile intervals, regardless of oil used.

The drive belt (v-belt) tension specification has been updated to address this condition.

been disconnected or power to the Engine ECM has been interrupted.

There are multiple benefits of this oil. Due to the improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicle that require this oil.

This Tech Tip applies only to cases with: *P219A and abnormal compression test results; *Engine serial number is prior to F071611

There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.

There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.

Typically this condition occurs during cold engine start up.

POWER TO THE ENGINE ECM HAS BEEN INTERRUPTED.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.

? The Parts Information section has been updated. Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced

? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

be involved.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.

inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.

(Lollipop) or later.

(Lollipop) or later.

Click on the TIS tab, Diagnostics tab, Telematics tab, and the document is now located under the reference documents sections. This change has occurred to help speed up the updating process of this document.

The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

THE CUSTOMER'S IPHONE IS CONNECTED TO THE VEHICLE VIA BLUETOOTH. THE CUSTOMER MAY COMPLAIN OF THE FOLLOWING ISSUES: WHEN RECEIVING TWO INCOMING CALLS SIMULTANEOUSLY, BOTH CALLS ARE ENDED AUTOMATICALLY. ITUNES RADIO APP DOES NOT PLAY VIA BLUETOOTH AUDIO. PODCAST AND AUDIOBOOK MEDIA PLAYBACK IS INOPERATIVE VIA BLUETOOTH AUDIO.

(LOLLIPOP) OR LATER.

Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).

Please see T-SB-0304-17.

Please see T-SB-0304-17.

performance.

campaign repairs completed.

campaign repairs completed.

2012 YARIS. *RM

*RM

reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pretensioner devices did not perform as expected, please follow the steps in the recommendations section below.

Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.

Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.

seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.

ITS POSSIBLE THAT THE DEVICES MAY OR MAY NOT PERFORM AS EXPECTED WITH UNINTENDED DEPLOYMENT. MODEL YEARS 1990-2013. MODELS VARIOUS MODELS. *PE

*PE

*PE

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly

automatic transmissions.

assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.

converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.

mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.

ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.