2016 Toyota Tacoma TSBs

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

seen with the hood open, and on the A-pillars on certain Tacoma vehicles with 040 Super White paint color. Although the vehicle paint is covered by Toyotas New Vehicle Limited Warranty for three years, or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to the conditions described above.

INNER FENDERS AND A-PILLARS CERTAIN 2016-2022 MODEL YEAR TACOMA

seen with the hood open, and on the A-pillars on certain Tacoma vehicles with 040 Super White paint color. Although the vehicle paint is covered by Toyotas New Vehicle Limited Warranty for three years, or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to the conditions described above.

window door frames, inner fender edges under the hood, and/or A-pillars. The affected panel(s) require repainting to address this condition. The paint repair may need to be sublet to a body shop.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

window door frames and/or inner fender edges under the hood. The affected panel(s) require repainting to address this condition. The paint repair may need to be sublet to a body shop.

FENDERS CERTAIN 2016-2022 MODEL YEAR TACOMA

FENDERS CERTAIN 2016-2022 MODEL YEAR TACOMA

to provide coverage for paint peeling on door frames and front inner fenders on certain 2016-2022 model year Tacoma vehicles. Toyota has received some reports of paint peeling along the exterior door window frames and front inner fenders under the hood on certain Tacoma vehicles with 040 Super White paint color. Although the vehicle paint is covered by Toyotas New Vehicle Limited Warranty for three years, or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to the condition described above.

the hood on certain Tacoma vehicles with 040 Super White paint color. Although the vehicle paint is covered by Toyotas New Vehicle Limited Warranty for three years, or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN K0D FRAME CORROSION RESISTANT COMPOUND (CRC) APPLICATION CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN K0D FRAME CORROSION RESISTANT COMPOUND (CRC) APPLICATION CERTAIN 2011 ? 2015 MODEL YEAR TACOMA

Peeling on Door Frames + Front Inner Fenders Frequently Asked Questions

under the hood on certain Tacoma vehicles with 040 Super White paint color.

under the hood on certain Tacoma vehicles with 040 Super White paint color.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

left front door and front fender, preventing the front door from fully opening. Follow the Repair Procedure in this bulletin to address this condition.

left front door and front fender, preventing the front door from fully opening. Follow the Repair Procedure in this bulletin to address this condition.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal.

If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

CENTER HIGH-MOUNTED STOP LAMP ? WATER LEAK

CENTER HIGH-MOUNTED STOP LAMP ? WATER LEAK

If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal.

with part number 00948-CHMHW-01, this part number has been created for CLAIM FILING PUPRPOSES ONLY. Part number 00948-CHMSL-HW should no longer be included when submitting claims.

If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

CERTAIN 2011 ? 2015 MODEL YEAR TACOMA

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

CERTAIN 2011 ? 2015 MODEL YEAR TACOMA

CERTAIN 2011 ? 2015 MODEL YEAR TACOMA

CERTAIN 2016 ? 2017 MODEL YEAR TACOMA

2016 ? 2017 MODEL YEAR TACOMA

APPLICATION CERTAIN 2016 ? 2017 MODEL YEAR TACOMA (2011-2015 model year instructions can be found on TIS)

APPLICATION CERTAIN 2016 ? 2017 MODEL YEAR TACOMA (2011-2015 model year instructions can be found on TIS)

APPLICATION CERTAIN 2016 ? 2017 MODEL YEAR TACOMA (2011-2015 model year instructions can be found on TIS)

Follow the Repair Procedure in this bulletin to address this condition

T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

Upon closer inspection, it may become apparent that the water leak is coming from the space between the center high mount stop lamp and the body of the vehicle. Follow the Repair Procedure in this bulletin to address this condition.

Upon closer inspection, it may become apparent that the water leak is coming from the space between the center high mount stop lamp and the body of the vehicle. Follow the Repair Procedure in this bulletin to address this condition.

noise from the rear of the vehicle. This condition may occur while driving around 50 mph at constant speed, slight acceleration, or slight deceleration and may be caused by rear differential vibration transferring through the chassis and body. Follow the Repair Procedure in this bulletin to address this condition.

noise from the rear of the vehicle. This condition may occur while driving around 50 mph at constant speed, slight acceleration, or slight deceleration and may be caused by rear differential vibration transferring through the chassis and body. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

Upon closer inspection, it may become apparent that the water leak is coming from the space between the center high mount stop lamp and the body of the vehicle. Follow the Repair Procedure in this bulletin to address this condition.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

with Diagnostic Trouble Code (DTC) C1AB2 Short to GND in Outer Mirror Indicator (Master) or C1AB3 Short to GND in Outer Mirror Indicator (Slave) stored. Follow the Repair Procedure in this bulletin to address this condition.

On some vehicles, when Rapgard? is removed the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is NOT necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

type noise from the rear of the vehicle. This condition may occur while driving around 50 mph at constant speed, slight acceleration, or slight deceleration and may be caused by rear differential vibration transferring through the chassis and body. Follow the Repair Procedure in this bulletin to address this condition. APPLICABLE WARRANTY ? This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle?s in-service date. ? Warranty application is limited to occurrence of the specified condition described in this bulletin.

when driving in high cross-wind areas. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

type noise from the rear of the vehicle. This condition may occur while driving around 50 mph at constant speed, slight acceleration, or slight deceleration and may be caused by rear differential vibration transferring through the chassis and body. Follow the Repair Procedure in this bulletin to address this condition. APPLICABLE WARRANTY ? This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle?s in-service date. ? Warranty application is limited to occurrence of the specified condition described in this bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

weather, may exhibit an intermittent or abnormal windshield wiper operation when initially turned on due to snow or sleet accumulation under the cowl louver.

Use the following procedure to complete initial calibration of the compass during Pre-Delivery Service (PDS). There are two types of mirrors that are equipped with a compass (Type A and Type B). Determine which type the vehicle is equipped with and follow the calibration procedure for that mirror.

THESE STAINS APPEAR TO BE UNDER THE CLEAR COAT (REPAINTING THIS AREA IS NOT NECESSARY). THE STAIN PATTERNS ARE USUALLY UNDER WRINKLES IN THE RAPGARD. THESE WRINKLES SOMETIMES TRAP WATER AND CAUSE THE PAINT TO STAIN FROM THE TRAPPED MOISTURE, ESPECIALLY ON HORIZONTAL SURFACES, SUCH AS THE HOOD, ROOF, AND TRUNK. STAINS CAN BE REMOVED BY HEATING THE STAINED SURFACE TO REMOVE THE TRAPPED MOISTURE.

USE THE FOLLOWING PROCEDURE TO COMPLETE INITIAL CALIBRATION OF THE COMPASS DURING PRE-DELIVERY SERVICE (PDS). THERE ARE TWO TYPES OF MIRRORS THAT ARE EQUIPPED WITH A COMPASS (TYPE A AND TYPE B). DETERMINE WHICH TYPE THE VEHICLE IS EQUIPPED WITH AND FOLLOW THE CALIBRATION PROCEDURE FOR THAT MIRROR.

WITH DIAGNOSTIC TROUBLE CODE (DTC) C1AB2 SHORT TO GND IN OUTER MIRROR INDICATOR (MASTER) OR C1AB3 SHORT TO GND IN OUTER MIRROR INDICATOR (SLAVE) STORED. FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THIS CONDITION.

Toyota has received reports regarding frame corrosion perforation on 2011 ? 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame. Although perforation of the vehicle?s frame is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to vehicle frame corrosion perforation. A separate program (limited Service Campaign K0D) will include CRC (Corrosion Resistant Compound) application. CRC application will be covered under Limited Service Campaign (LSC K0D) for a period of two years and will only be available for vehicles registered/regularly operated in the Cold Climate States that do not meet vehicle frame replacement criteria.

These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame. Although perforation of the vehicle?s frame is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to vehicle frame corrosion perforation. A separate program (limited Service Campaign K0D) will include CRC (Corrosion Resistant Compound) application. CRC application will be covered under Limited Service Campaign (LSC K0D) for a period of two years and will only be available for vehicles registered/regularly operated in the Cold Climate States that do not meet vehicle frame replacement criteria.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame. 1 ? District of Columbia (DC), CT, DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI, and WV. Although perforation of the vehicle?s frame is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to vehicle frame corrosion perforation. A separate program (limited Service Campaign K0D) will include CRC (Corrosion Resistant Compound) application. CRC application will be covered under Limited Service Campaign (LSC K0D) for a period of two years and will only be available for vehicles registered/regularly operated in the Cold Climate States that do not meet vehicle frame replacement criteria.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

The various 1234YF compressor oils (ND-12, PS-D1, or VC100YF) are available through the Toyota Approved Dealer Equipment website.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

Toyota has received reports regarding frame corrosion perforation on 2011 ? 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

APPLICATION CERTAIN 2016 ? 2017 MODEL YEAR TACOMA (2011-2015 model year instructions can be found on TIS) COLD CLIMATE STATES ONLY

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

APPLICATION CERTAIN 2016 ? 2017 MODEL YEAR TACOMA (2011-2015 model year instructions can be found on TIS) COLD CLIMATE STATES ONLY

Toyota has received reports regarding frame corrosion perforation on 2011 ? 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.

Warranty Reimbursement Procedure has been updated to reflect K0D Launch and possible outcomes after inspection. Toyota has received reports regarding vehicle frame corrosion perforation on certain 2011-2017 model year Tacoma vehicles. These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame. 1 ? District of Columbia (DC), CT, DE, IL, IN, KY, MA, MD, ME, MI, MN, NH, NJ, NY, OH, PA, RI, VA, VT, WI, and WV. Although perforation of the vehicle?s frame is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to vehicle frame corrosion perforation. A separate program will be announced in the future and will include CRC (Corrosion Resistant Compound) application. Toyota is currently preparing parts and approvals for the CRC application process. CRC application will be covered under a separate Limited Service Campaign (LSC K0D) for a period of two years and will only be available for vehicles registered/regularly operated in the Cold Climate States that do not meet vehicle frame replacement criteria. This Limited Service Campaign has not yet launched at the time of this publication. Toyota expects to launch K0D in phases beginning in the Fall of 2019. The expected schedule can be seen in the chart below.

vehicles covered under the 3 years or 36,000 miles (whichever comes first) New Vehicle Limited Warranty. Toyota has received a number of reports regarding vehicle frame corrosion perforation on certain 2011-2017 model year Tacoma vehicles. These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame.

These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame.

These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame.

These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame.

These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame.

to complete the repairs, the various 1234YF compressor oils (ND-12, PS-D1, or VC100YF) are available through the Toyota Approved Dealer Equipment website.

Follow the Repair Procedure in this bulletin to address this condition.

Adding stop leak products to the A/C system is not a recommended or approved Toyota repair process. During A/C service, moisture enters the A/C system, and can react with the previously added A/C stop leak, forming a gelatinous substance. The gel substance that forms can cause the A/C compressor to bind and or seize.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

The HVAC under hood label and label on the A/C compressor specifies the use of PS-D1 oil. However, the Repair Manual references the use of ND-12 oil for the A/C Compressor.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

THE HVAC UNDER HOOD LABEL AND LABEL ON THE A/C COMPRESSOR SPECIFIES THE USE OF PS-D1 OIL. HOWEVER, THE REPAIR MANUAL REFERENCES THE USE OF ND-12 OIL FOR THE A/C COMPRESSOR."

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

(whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the presence of a fuel odor in or around the engine bay originating at the high-pressure fuel pump of the subject vehicles.

year Sienna, and 2016 ? 2023 model year Tacoma vehicles equipped with a 2GR-FKS engine may exhibit a knocking noise from the vacuum pump at idle. Follow the Repair Procedure in this bulletin to address this condition

HVAC system when the air conditioning system is ON. The whistle noise may occur as the compressor cycles on and off and is more prevalent with increased engine RPM during hot ambient temperatures. Follow the Repair Procedure in this bulletin to address this condition.

in some 2016 ? 2022 model year Toyota vehicles equipped with an FKS engine

HVAC system when the air conditioning system is ON. The whistle noise may occur as the compressor cycles ON/OFF and is more prevalent with increased engine RPM during hot ambient temperatures. Follow the Repair Procedure in this bulletin to address this condition.

Follow the Repair Procedure in this bulletin to address this condition.

in some 2016 ? 2021 model year Toyota vehicles equipped with an FKS engine.

ON condition with Diagnostic Trouble Code (DTC) P211904 (ECM/PCM Throttle Actuator ?A? Control Throttle Body Range/Performance System Internal Failure) with vehicle entering limp mode. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.

stops blowing cool air during periods of extended engine idle with ambient temperatures greater than 100F. Follow the Repair Procedure in the bulletin to address this condition.

and Camry Hybrid vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P261093 (ECM/PCM Engine Off Timer Performance No Operation) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.

Follow the Repair Procedure in this bulletin to address this condition.

stops blowing cool air during periods of extended engine idle with ambient temperatures greater than 100F. Follow the Repair Procedure in the bulletin to address this condition.

ON condition with Diagnostic Trouble Code (DTC) P211904 (ECM/PCM Throttle Actuator ?A? Control Throttle Body Range/Performance System Internal Failure) with vehicle entering limp mode. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.

year Tacoma vehicles may exhibit a knocking noise from the vacuum pump with the engine idling. Follow the Repair Procedure in this bulletin to address this condition.

Diagnostic Trouble Codes (DTCs) P013A00 and/or P013C00 (O2 Slow Response) due to an incomplete weld around the front exhaust pipe assembly (either bank). Follow the Repair Procedure in this bulletin to address this condition.

stops blowing cool air during periods of extended engine idle with ambient temperatures greater than 100F. Follow the Repair Procedure in the bulletin to address this condition.

Diagnostic Trouble Codes (DTCs) P013A00 and/or P013C00 (O2 Slow Response) due to an incomplete weld around the front exhaust pipe assembly (either bank). Follow the Repair Procedure in this bulletin to address this condition.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

stops blowing cool air during periods of extended engine idle with ambient temperatures greater than 100F. Follow the Repair Procedure in the bulletin to address this condition.

and Camry Hybrid vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P261093 (ECM/PCM Engine Off Timer Performance No Operation) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.

injectors manually on 2GR-FKS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. To avoid this condition, technicians should raise engine RPM when changing back and forth between the Direct Injection and Port Injection active tests. Use the recommended procedure below to avoid this concern while testing injection mode of FKS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning vehicle to customer.

controlling the direct injectors manually on 2GR-FKS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. In order to avoid this condition, technicians should raise engine RPM when changing from Direct Injection active test to Port Injection active test. Use the recommended procedure below to avoid this concern while testing injection mode of 2GR-FKS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning vehicle to customer.

feeling under the following conditions. ? Vehicle is traveling between 40 and 50 mph ? Transmission is in fourth or fifth gear ? During torque converter lock-up The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been revised to address this condition. Follow the Repair Procedure in this bulletin to address this condition.

MODEL TACOMA

A blower motor fan hub with improper dimensions may develop a crack over time. If a vehicle is continuously operated with this condition, the damage may worsen, leading to an abnormal noise and eventually an inoperable blower motor fan.

A blower motor fan hub with improper dimensions may develop a crack over time. If a vehicle is continuously operated with this condition, the damage may worsen, leading to an abnormal noise and eventually an inoperable blower motor fan.

A blower motor fan hub with improper dimensions may develop a crack over time. If a vehicle is continuously operated with this condition, the damage may worsen, leading to an abnormal noise and eventually an inoperable blower motor fan.

2018 model year) vehicles may exhibit a knocking noise from the vacuum pump. Follow the Repair Procedure in this bulletin to address this condition.

MODEL TACOMA

A blower motor fan hub with improper dimensions may develop a crack over time. If a vehicle is continuously operated with this condition, the damage may worsen, leading to an abnormal noise and eventually an inoperable blower motor fan.

A blower motor fan hub with improper dimensions may develop a crack over time. If a vehicle is continuously operated with this condition, the damage may worsen, leading to an abnormal noise and eventually an inoperable blower motor fan.

A blower motor fan hub with improper dimensions may develop a crack over time. If a vehicle is continuously operated with this condition, the damage may worsen, leading to an abnormal noise and eventually an inoperable blower motor fan.

2018 model year) vehicles may exhibit a knocking noise from the vacuum pump. Follow the Repair Procedure in this bulletin to address this condition.

The surge is most noticeable under the following conditions: ? The vehicle is operated at an idle creep speed. ? The steering wheel is turned (i.e., backing out of a garage or executing parking lot maneuvers). ? The engine coolant temperature is low. Follow the Repair Procedure in this bulletin to address this condition.

feeling under the following conditions. ? Vehicle is traveling between 40 and 50 mph ? Transmission is in fourth or fifth gear ? During torque converter lock-up The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been revised to address this condition. Follow the Repair Procedure in this bulletin to address this condition.

equipped with a 2GR-FKS engine may exhibit an engine oil leak from the cam sensor bolt hole(s). Follow the Repair Procedure in this bulletin to address this condition.

stops blowing cool air during periods of extended engine idle with ambient temperatures greater than 100F. Follow the Repair Procedure in the bulletin to address this condition.

stumble at wide open throttle takeoff during operation in a high-altitude area. Follow the Repair Procedure in this bulletin to address this condition.

feeling under the following conditions: ? Vehicle is traveling between 40 ? 50 mph ? Transmission is in fourth or fifth gear ? During torque converter lock-up The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been revised to address this condition. Follow the Repair Procedure in this bulletin to address this condition.

Vehicles Equipped with BD20 Differential: - Tacoma 4x4 ? 4 cylinder ? Automatic Transmission - Tacoma 4x4 ? 6 cylinder ? Automatic Transmission - Tacoma PreRunner. There are 10 fasteners on the BD20 differential (12mm fastener / 8 mm stud). The fastener part numbers are 90170-08042 & 90170-08036. There are two different torque values for these fasteners: ? 90170-08042 ? 18 ft. lbs. {25 N?m, 255 kgf?cm} ? 90170-08036 ? 28 ft. lbs. {37 N?m, 378 kgf?cm} Vehicles produced between 8/2015 through 5/12/2017 should be equipped with 90170-08042. Vehicles produced 5/18/2017 and after should be equipped with 90170-08036.

exhibit one or more of the following shift feeling concerns: *Delayed engagement Park to Drive or Reverse to Drive. *Harsh 1st - 2nd upshift. *Delayed upshift when using cruise control. The Engine Control Module (ECM, SAE term: Powertrain Control Module/PCM) calibration has been revised to address this condition.

? This condition is most noticeable when at least one of the following conditions are met: o One or more of the vehicle?s windows are rolled down o The vehicle is idling next to a large object, i.e. a wall or another vehicle o The customer is navigating a drive-thru

with a 2GR-FKS engine may exhibit a knocking noise from the vacuum pump. Follow the Repair Procedure below to address this condition.

when shifting out of ANY gear after driving for an extended period of time. Follow the Repair Procedure in the bulletin to address this condition.

with a 2GR-FKS engine may exhibit a chirping noise from the high-pressure fuel pump. Follow the Repair Procedure in this bulletin to address this condition.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

Diagnostic Trouble Code (DTC) P011B - Engine Coolant Temperature / Intake Air Temperature Correlation - when no part malfunction is present. The Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Use the following repair procedure to address this condition.

when shifting out of 5th or 6th gear after driving for an extended period of time. Follow the Repair Procedure in the bulletin to address this condition.

exhibit a flare during the 2-3 up shift. Customers may describe this as a momentary Automatic Transmission slipping feeling. The Engine Control Module (ECM, SAE term: Powertrain Control Module/PCM) calibration has been revised. Use the following Repair Procedure to address this condition.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

EXHIBIT A FLARE DURING THE 2-3 UP SHIFT. CUSTOMERS MAY DESCRIBE THIS AS A MOMENTARY AUTOMATIC TRANSMISSION SLIPPING FEELING. THE ENGINE CONTROL MODULE (ECM, SAE TERM: POWERTRAIN CONTROL MODULE/PCM) CALIBRATION HAS BEEN REVISED. USE THE FOLLOWING REPAIR PROCEDURE TO ADDRESS THIS CONDITION.

THIS CONDITION IS MOST NOTICEABLE WHEN AT LEAST ONE OF THE FOLLOWING CONDITIONS ARE MET: O ONE OR MORE OF THE VEHICLES WINDOWS ARE ROLLED DOWN O THE VEHICLE IS IDLING NEXT TO A LARGE OBJECT, I.E. A WALL OR ANOTHER VEHICLE O THE CUSTOMER IS NAVIGATING A DRIVE-THRU"

DIAGNOSTIC TROUBLE CODE (DTC) P011B - ENGINE COOLANT TEMPERATURE / INTAKE AIR TEMPERATURE CORRELATION WHEN NO PART MALFUNCTION IS PRESENT. THE ENGINE CONTROL MODULE/ECM (SAE TERM: POWERTRAIN CONTROL MODULE/PCM) LOGIC HAS BEEN MODIFIED TO REDUCE THE POSSIBILITY OF THIS CONDITION OCCURRING. USE THE FOLLOWING REPAIR PROCEDURE TO ADDRESS THIS CONDITION.

CONTROLLING THE DIRECT INJECTORS MANUALLY ON 2GR-FKS ENGINES. WHEN DIRECT INJECTION IS STARTED AND THEN STOPPED USING THE ACTIVE TEST, CURRENT ECU LOGIC DOES NOT TURN OFF THE DIRECT INJECTORS AND CAN CAUSE DTCS P017200, P017500 AND P0160300. IN ORDER TO AVOID THIS CONDITION, TECHNICIANS SHOULD RAISE ENGINE RPM WHEN CHANGING FROM DIRECT INJECTION ACTIVE TEST TO PORT INJECTION ACTIVE TEST. USE THE RECOMMENDED PROCEDURE BELOW TO AVOID THIS CONCERN WHILE TESTING INJECTION MODE OF 2GR-FKS EQUIPPED VEHICLES. NOTE: IF THE ACTIVE TEST IS USED MULTIPLE TIMES WITHOUT USING THIS PROCEDURE TO RAISE ENGINE RPM, IT MAY BE NECESSARY TO RESET LEARNING VALUES FOR FUEL TRIM AND AIR TO FUEL RATIO BEFORE RETURNING VEHICLE TO CUSTOMER."

EXHIBIT ONE OR MORE OF THE FOLLOWING SHIFT FEELING CONCERNS: *DELAYED ENGAGEMENT PARK TO DRIVE OR REVERSE TO DRIVE. *HARSH 1ST - 2ND UPSHIFT. *DELAYED UPSHIFT WHEN USING CRUISE CONTROL. THE ENGINE CONTROL MODULE (ECM, SAE TERM: POWERTRAIN CONTROL MODULE/PCM) CALIBRATION HAS BEEN REVISED TO ADDRESS THIS CONDITION.

EXHIBIT ONE OR MORE OF THE FOLLOWING SHIFT FEELING CONCERNS: *DELAYED ENGAGEMENT PARK TO DRIVE OR REVERSE TO DRIVE. *HARSH 1ST - 2ND UPSHIFT. *DELAYED UPSHIFT WHEN USING CRUISE CONTROL. THE ENGINE CONTROL MODULE (ECM, SAE TERM: POWERTRAIN CONTROL MODULE/PCM) CALIBRATION HAS BEEN REVISED TO ADDRESS THIS CONDITION.

WHEN SHIFTING OUT OF 5TH OR 6TH GEAR AFTER DRIVING FOR AN EXTENDED PERIOD OF TIME. FOLLOW THE REPAIR PROCEDURE IN THE BULLETIN TO ADDRESS THIS CONDITION.

This is caused by the phone Hands Free volume being too low.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

In some instances, this condition causes the Panasonic head unit to reboot when the Bluetooth connection is initiated.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

during the head unit software installation process

In some instances, this condition causes the Panasonic head unit to reboot when the Bluetooth connection is initiated.

Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for echo or excessive background noise.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

which can be performed to diagnose the condition.

Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for Echo or excessive background noise.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

The Introduction has been updated to include new software changes. Some 2016 ? 2017 model year applicable vehicles equipped with Entune? Audio (version 01013E) / Entune? Audio Plus (version 010156 or 01015C) / Entune? Premium Audio (version 010171 or 010170 or 01017D) may exhibit one or more of the following conditions: ? Head unit rebooting at a specific location. ? Abnormal destination search operation. ? Rebooting caused by no songs on the USB connected iPhone. ? One time reboot after ACC-ON. ? Audio stays muted after the key is cycled.

(Lollipop) or later.

Please try again later.? If the following screen is seen; follow the directions below.

(Lollipop) or later.

Please try again later." If the following screen is seen, follow the directions below.

Click on the TIS tab, Diagnostics tab, Telematics tab, and the document is now located under the reference documents sections. This change has occurred to help speed up the updating process of this document.

The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.

Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for Echo or excessive background noise.

which can be performed to diagnose the condition.

Please try again later." If the following screen is seen; follow the directions below.

system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.

Please try again later.? If the following screen is seen; follow the directions below.

This is to promote safe driving practices and reduce the amount of distractions while driving. These lockouts can?t be deactivated or defeated through any settings. The following is a list of common lockouts, however, this is not a complete list of lockouts.

memory.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

or 01015C) / Entune Premium Audio (version 010171 or 010170 or 01017D) may exhibit one or more of the following conditions: *Head unit rebooting at a specific location. *Abnormal destination search operation. *Rebooting caused by no songs on the USB connected iPhone. *One time reboot after ACC-ON. *Audio stays muted after the key is cycled.

system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.

PLEASE TRY AGAIN LATER." IF THE FOLLOWING SCREEN IS SEEN, FOLLOW THE DIRECTIONS BELOW.

THE CUSTOMER'S IPHONE IS CONNECTED TO THE VEHICLE VIA BLUETOOTH. THE CUSTOMER MAY COMPLAIN OF THE FOLLOWING ISSUES: WHEN RECEIVING TWO INCOMING CALLS SIMULTANEOUSLY, BOTH CALLS ARE ENDED AUTOMATICALLY. ITUNES RADIO APP DOES NOT PLAY VIA BLUETOOTH AUDIO. PODCAST AND AUDIOBOOK MEDIA PLAYBACK IS INOPERATIVE VIA BLUETOOTH AUDIO.

SYSTEM WITH ANDROID PHONES RUNNING OS 4.4 OR LATER. CONDITION TENDS TO OCCUR TO CUSTOMERS WHO HAVE MANY PREVIOUS TEXT MESSAGES ON THEIR PHONES.

WHICH CAN BE PERFORMED TO DIAGNOSE THE CONDITION.

CURRENT MULTIMEDIA SYSTEMS ARE DESIGNED WITH THE ABILITY TO ADJUST BLUETOOTH SOUND QUALITY TO COMPENSATE FOR ECHO OR EXCESSIVE BACKGROUND NOISE.

CLICK ON THE TIS TAB, DIAGNOSTICS TAB, TELEMATICS TAB, AND THE DOCUMENT IS NOW LOCATED UNDER THE REFERENCE DOCUMENTS SECTIONS. THIS CHANGE HAS OCCURRED TO HELP SPEED UP THE UPDATING PROCESS OF THIS DOCUMENT. "

(LOLLIPOP) OR LATER.

OR 01015C) / ENTUNE PREMIUM AUDIO (VERSION 010171 OR 010170 OR 01017D) MAY EXHIBIT ONE OR MORE OF THE FOLLOWING CONDITIONS: *HEAD UNIT REBOOTING AT A SPECIFIC LOCATION. *ABNORMAL DESTINATION SEARCH OPERATION. *REBOOTING CAUSED BY NO SONGS ON THE USB CONNECTED IPHONE. *ONE TIME REBOOT AFTER ACC-ON. *AUDIO STAYS MUTED AFTER THE KEY IS CYCLED.

Please see T-SB-0057-18.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0045-22

Please see T-SB-0012-21.

Please see T-SB-0124-20.

Please see T-SB-0124-20.

Please see T-SB-0093-20.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0003-20.

Please see T-SB-0112-19.

Please see T-SB-0071-19.

The differential may exhibit noise or the fasteners may be loose.

Please see T-SB-0134-16.

Follow the Repair Procedure in this bulletin to address this condition.

Please see T-SB-0279-17.

Gap from hinge cover to tonneau cover should be no more than 0 -1mm.

GAP FROM HINGE COVER TO TONNEAU COVER SHOULD BE NO MORE THAN 0 -1MM.

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled.

One or more of the Heated Oxygen Sensors (O2) or Air Fuel ratio sensor (A/F) DTCs below could set due to a leaking exhaust system. If you encounter a vehicle with any of these DTCs

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

following Diagnostic Trouble Codes (DTCs) present. ? U0232 ? Lost Communication with Blind Spot Monitor Slave Module ? U0233 ? Lost Communication with Blind Spot Monitor Master Module ? C1AC1 ? Master Module Horizontal Axis Misalignment ? C1AC2 ? Slave Module Horizontal Axis Misalignment ? C1AB6 ? Blind Spot Monitor Master Module ? C1AB7 ? Blind Spot Monitor Slave Module. Follow the Repair Procedure in this bulletin to address this condition.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State of Charge (SOC) of the vehicle?s battery while in stock and assure proper State of Charge (SOC) at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, all dealers should check battery State of Charge (SOC) and recharge, if necessary, within 48 hours of delivery to customers.

T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

T-SB-0103-16 and T-SB-0337-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 and T-SB-0337-17 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2016 ? 2018 model year vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (version 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled

T-SB-0103-16 and T-SB-0337-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 and T-SB-0337-17 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2016 ? 2018 model year vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (version 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

? No sound from speakers ? No bass from speakers ? Muffled sound from speakers ? Inoperative power door locks ? Inoperative power windows ? No answer-back (beep/chirp) after locking the doors via key fob ? Interior illumination inoperative (lighting within HVAC controls, instrument panel switches, door panel switches, etc.) ? Open fuses for one or more of the systems listed above Follow the Repair Procedure in this bulletin to address these conditions.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

Customer feedback indicates the following areas deserve special attention when performing PDS: ? Careful inspection for paint chips/scratches and body dents/dings. ? Proper operation of electrical accessories (including interior light, clock, and radio reset). ? Interior cleanliness. ? Proper function of mechanical systems. Customer retention and proper maintenance of vehicles has been a major focus for Toyota and Scion. To help remind customers that regular oil changes are essential to the proper maintenance of their vehicle, dealers are required to begin installing a first oil change reminder sticker prior to delivery. By doing this, customers will be reminded to return to your dealership for their first oil change. Your current oil change

Customer feedback indicates the following areas deserve special attention when performing PDS: * Careful inspection for paint chips/scratches and body dents/dings. * Proper operation of electrical accessories (including interior light, clock, and radio reset). * Interior cleanliness. * Proper function of mechanical systems. Customer retention and proper maintenance of vehicles has been a major focus for Toyota and Scion. To help remind customers that regular oil changes are essential to the proper maintenance of their vehicle, dealers are required to begin installing a first oil change reminder sticker prior to delivery. By doing this, customers will be reminded to return to your dealership for their first oil change. Your current oil change reminder sticker may be used. (See PDS Check Sheet item 8 of "Final Inspection & Cleaning.") A new PDS Check Sheet has been developed for the 2016 model year Tacoma. Some check points have been added, expanded, or clarified. Bulletins are available for items in bold type.

Customer feedback indicates the following areas deserve special attention when performing PDS: * Careful inspection for paint chips/scratches and body dents/dings. * Proper operation of electrical accessories (including interior light, clock, and radio reset). * Interior cleanliness. * Proper function of mechanical systems. Customer retention and proper maintenance of vehicles has been a major focus for Toyota and Scion. To help remind customers that regular oil changes are essential to the proper maintenance of their vehicle, dealers are required to begin installing a first oil change reminder sticker prior to delivery. By doing this, customers will be reminded to return to your dealership for their first oil change. Your current oil change reminder sticker may be used. (See PDS Check Sheet item 8 of "Final Inspection & Cleaning.") A new PDS Check Sheet has been developed for the 2016 model year Tacoma. Some check points have been added, expanded, or clarified. Bulletins are available for items in bold type.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

CUSTOMER FEEDBACK INDICATES THE FOLLOWING AREAS DESERVE SPECIAL ATTENTION WHEN PERFORMING PDS: H CAREFUL INSPECTION FOR PAINT CHIPS/SCRATCHES AND BODY DENTS/DINGS. H PROPER OPERATION OF ELECTRICAL ACCESSORIES (INCLUDING INTERIOR LIGHT, CLOCK, AND RADIO RESET). H INTERIOR CLEANLINESS. H PROPER FUNCTION OF MECHANICAL SYSTEMS. CUSTOMER RETENTION AND PROPER MAINTENANCE OF VEHICLES HAS BEEN A MAJOR FOCUS FOR TOYOTA AND SCION. TO HELP REMIND CUSTOMERS THAT REGULAR OIL CHANGES ARE ESSENTIAL TO THE PROPER MAINTENANCE OF THEIR VEHICLE, DEALERS ARE REQUIRED TO BEGIN INSTALLING A FIRST OIL CHANGE REMINDER STICKER PRIOR TO DELIVERY. BY DOING THIS, CUSTOMERS WILL BE REMINDED TO RETURN TO YOUR DEALERSHIP FOR THEIR FIRST OIL CHANGE. YOUR CURRENT OIL CHANGE REMINDER STICKER MAY BE USED. (SEE PDS CHECK SHEET ITEM 8 OF FINAL INSPECTION & CLEANING.) A NEW PDS CHECK SHEET HAS BEEN DEVELOPED FOR THE 2016 MODEL YEAR TACOMA. SOME CHECK POINTS HAVE BEEN ADDED, EXPANDED, OR CLARIFIED. BULLETINS ARE AVAILABLE FOR ITEMS IN BOLD TYPE."

CUSTOMER FEEDBACK INDICATES THE FOLLOWING AREAS DESERVE SPECIAL ATTENTION WHEN PERFORMING PDS: H CAREFUL INSPECTION FOR PAINT CHIPS/SCRATCHES AND BODY DENTS/DINGS. H PROPER OPERATION OF ELECTRICAL ACCESSORIES (INCLUDING INTERIOR LIGHT, CLOCK, AND RADIO RESET). H INTERIOR CLEANLINESS. H PROPER FUNCTION OF MECHANICAL SYSTEMS. CUSTOMER RETENTION AND PROPER MAINTENANCE OF VEHICLES HAS BEEN A MAJOR FOCUS FOR TOYOTA AND SCION. TO HELP REMIND CUSTOMERS THAT REGULAR OIL CHANGES ARE ESSENTIAL TO THE PROPER MAINTENANCE OF THEIR VEHICLE, DEALERS ARE REQUIRED TO BEGIN INSTALLING A FIRST OIL CHANGE REMINDER STICKER PRIOR TO DELIVERY. BY DOING THIS, CUSTOMERS WILL BE REMINDED TO RETURN TO YOUR DEALERSHIP FOR THEIR FIRST OIL CHANGE. YOUR CURRENT OIL CHANGE REMINDER STICKER MAY BE USED. (SEE PDS CHECK SHEET ITEM 8 OF FINAL INSPECTION & CLEANING.) A NEW PDS CHECK SHEET HAS BEEN DEVELOPED FOR THE 2016 MODEL YEAR TACOMA. SOME CHECK POINTS HAVE BEEN ADDED, EXPANDED, OR CLARIFIED. BULLETINS ARE AVAILABLE FOR ITEMS IN BOLD TYPE."

FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION."

CUSTOMER FEEDBACK INDICATES THE FOLLOWING AREAS DESERVE SPECIAL ATTENTION WHEN PERFORMING PDS: H CAREFUL INSPECTION FOR PAINT CHIPS/SCRATCHES AND BODY DENTS/DINGS. H PROPER OPERATION OF ELECTRICAL ACCESSORIES (INCLUDING INTERIOR LIGHT, CLOCK, AND RADIO RESET). H INTERIOR CLEANLINESS. H PROPER FUNCTION OF MECHANICAL SYSTEMS. CUSTOMER RETENTION AND PROPER MAINTENANCE OF VEHICLES HAS BEEN A MAJOR FOCUS FOR TOYOTA AND SCION. TO HELP REMIND CUSTOMERS THAT REGULAR OIL CHANGES ARE ESSENTIAL TO THE PROPER MAINTENANCE OF THEIR VEHICLE, DEALERS ARE REQUIRED TO BEGIN INSTALLING A FIRST OIL CHANGE REMINDER STICKER PRIOR TO DELIVERY. BY DOING THIS, CUSTOMERS WILL BE REMINDED TO RETURN TO YOUR DEALERSHIP FOR THEIR FIRST OIL CHANGE. YOUR CURRENT OIL CHANGE"

THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE. AS A MATTER OF POLICY, TOYOTA DOES NOT PROVIDE BATTERY WARRANTY COVERAGE FOR DISCHARGED AND/OR FAILED BATTERIES DUE TO LACK OF MAINTENANCE. IT IS THE DEALERS RESPONSIBILITY TO MAINTAIN THE SPECIFIED STATE OF CHARGE (SOC) OF THE VEHICLES BATTERY WHILE IN STOCK AND ASSURE PROPER STATE OF CHARGE (SOC) AT DELIVERY. TO ELIMINATE CUSTOMER SERVICE CONCERNS DUE TO AN UNDERCHARGED BATTERY DURING THE FIRST FEW WEEKS OF OWNERSHIP, ALL DEALERS SHOULD CHECK BATTERY STATE OF CHARGE (SOC) AND RECHARGE, IF NECESSARY, WITHIN 48 HOURS OF DELIVERY TO CUSTOMERS."

from the clutch pedal when it is depressed or released.

deceleration (coasting or braking) typically between 30 ? 10 mph. This vibration is felt in the seat, floorboard, and/or steering wheel. Follow the Repair Procedure in this bulletin to address this condition

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match the radio station that is playing.?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi/km?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010145), Entune? Audio Plus (version 010161), Entune? Premium Audio (version 010189), or earlier may exhibit one of the following conditions: ?Map will not display after it has been reprogrammed from the map micro SD card. Updated system software is now

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match the radio station that is playing.?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi/km?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010145), Entune? Audio Plus (version 010161), Entune? Premium Audio (version 010189), or earlier may exhibit one of the following conditions: ?Map will not display after it has been reprogrammed from the map micro SD card. Updated system software is now avail

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match radio station that is playing. ?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Updated system software is now available to address these conditions. Follow the Software Update Procedure in this bulletin to install the latest software version.

deceleration (coasting or braking) between 30 ? 10 mph. This vibration is felt in the seat, floorboard, and/or steering wheel. Follow the Repair Procedure in this bulletin to address this condition.

deceleration (coasting or braking) between 30 ? 10 mph. This vibration is felt in the seat, floorboard, and/or steering wheel. Follow the Repair Procedure in this bulletin to address this condition.

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match radio station that is playing. ?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative.

T-SB-0171-16. Some 2016 ? 2019 model year Tacoma vehicles equipped with an automatic transmission may exhibit a vibration under deceleration (coasting or braking) between 30 ? 10 mph. This vibration is felt in the seat, floorboard, and/or steering wheel.

deceleration (coasting or braking) between 10 ? 30 mph. This vibration is felt in the seat, floorboard, and/or steering wheel. Follow the Repair Procedure in this bulletin to address this condition.

T-SB-0279-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0279-17 is obsolete and ANY printed versions should be discarded. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ? Head unit reboots intermittently ? Half blank screen appears when on the maintenance screen and shifting to Reverse ? Screen freezes during an incoming phone call ? Incorrect time displays on the diagnostic menu ? Radio station information does not match radio station that is playing ? Abnormal playlist browsing operation ? Mute stays enabled after key cycle ? ?Search along my route? is inoperative ? Traffic data scales improperly ? Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?) ? MID compass does not match navigation screen when switching to North up ? Navigation does not match MID when switching from miles to kilometers ? Speed limit is blank on navigation screen ? Go button on VR screen is inoperative

T-SB-0186-12. * Applicability has been updated to include 2018 and 2019 model year Tacoma vehicles. * The entire bulletin has been updated. Service Bulletin No. T-SB-0186-12 is obsolete and any printed versions should be discarded. Some 2005 - 2019 model year Tacoma vehicles equipped with a manual transmission may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released. Follow the Repair Procedure in this bulletin to address this condition.

T-SB-0171-16. ? The Repair Procedure section has been updated. Service Bulletin No. T-SB-0171-16 is obsolete and any printed versions should be discarded. Some 2016 ? 2019 model year Tacoma vehicles equipped with an automatic transmission may exhibit a vibration felt in the seat, floorboard, and/or steering wheel between 10 ? 30 mph, caused by a driveline vibration under deceleration. Follow the Repair Procedure in this bulletin to address this condition. NOTE ? This Service Bulletin ONLY applies to 4WD models equipped with 6AT. Do NOT use the spring part number found in the Service Bulletin for ANY manual transmission vehicles or PreRunner models. This could lead to NEW, currently nonexistent issues. ? If the vehicle is installed with an aftermarket suspension/body lift or leveling kit, this Service Bulletin does NOT apply.

seat, floorboard, and/or steering wheel between 10 ? 30 mph, caused by a driveline vibration under deceleration. Follow the Repair Procedure in this bulletin to address this condition. NOTE ? This Service Bulletin ONLY applies to 4WD models equipped with 6AT. Do NOT use the spring part number found in the Service Bulletin for ANY manual transmission vehicles or PreRunner models. This could lead to NEW, currently nonexistent issues. ? If the vehicle is installed with an aftermarket suspension/body lift or leveling kit, this Service Bulletin does NOT apply.

After replacing the actuator, the normal operating condition is restored. Investigation of recovered parts show that damage is due to improper shifting pattern from N to D during 4LO entering/exiting operation.

pitch whine noise when driving in 5th or 6th gear. A NEW heat insulator is available to address this condition.

TC004-06. ? Applicability has been updated to include 2007 ? 2012 model year Tacoma vehicles. ? The Repair Procedure section has been updated. Service Bulletin No. TC004-06 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2005 ? 2017 model year Tacoma vehicles may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released. Follow the Repair Procedure in this bulletin to address this condition.

The Introduction, Production Change Information, and Repair Procedure sections have been updated. Some 2016 ? 2017 model year Tacoma vehicles equipped with an automatic transmission may exhibit a vibration felt in the seat, floorboard, and/or steering wheel between 10 ? 30 mph caused by a driveline vibration under deceleration. NOTE This Service Bulletin ONLY applies to 4WD models equipped with 6AT. Do NOT use the spring part number found in the Service Bulletin for any manual transmission vehicles or PreRunner models. This could lead to NEW, non-existing issues. If the vehicle has an aftermarket suspension/body lift or leveling kit installed, this bulletin does NOT apply.

AFTER REPLACING THE ACTUATOR, THE NORMAL OPERATING CONDITION IS RESTORED. INVESTIGATION OF RECOVERED PARTS SHOW THAT DAMAGE IS DUE TO IMPROPER SHIFTING PATTERN FROM N TO D DURING 4LO ENTERING/EXITING OPERATION.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

Follow the Repair Procedure in this bulletin to address this condition.

and the coil spring at full steering lock.

Brake vibration can occur at any time if improper torque is applied to lug nuts. Even one lug nut over or under torqued can cause vibration.

This can occur at various speeds or pedal application forces.

even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface

Sand, dirt and/or debris may enter the space between the silencer pad and contact surface of the leaf spring. When the vehicle rear suspension experiences any movement, friction is caused between the silencer pad and spring components, which may result in a squeak noise.

THIS CAN OCCUR AT VARIOUS SPEEDS OR PEDAL APPLICATION FORCES.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

air conditioning Evaporator Core (88511- #####) or Radiator Heater Unit SubAssembly (87107- #####

air conditioning Evaporator Core (87511- #####) or Radiator Heater Unit Sub-Assembly (87107- #####).

Tacoma vehicles.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

Service Tool Set is required to properly install the seal onto the injector. As new vehicle configurations have been released, several injector seal tool sets have been distributed to accommodate these new vehicles. There are a total of three injector seal tool sets for Toyota models, located in the appropriate SST cabinets. Each kit contains multiple pieces as shown in the diagram below. The individual pieces must remain together to ensure these tools are used correctly. Refer to the repair manual for the tool information to ensure the correct tool is used for the desired application.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle's systems and components. Any problems that are found should be corrected immediately.

THE FOLLOWING GUIDELINES SHOULD BE PERFORMED TO MINIMIZE VEHICLE COMPONENT/PART DEGRADATION DUE TO EXTENDED VEHICLE STORAGE CONDITIONS. LONG-TERM STORAGE CAN AFFECT A VEHICLES SYSTEMS AND COMPONENTS. ANY PROBLEMS THAT ARE FOUND SHOULD BE CORRECTED IMMEDIATELY."

Bosch Automotive Service Solutions will be facilitating this program on behalf of Toyota. Included in the Toyota Spray Wax Aftersales Support Program are approximately 20 tools. The tools will be available to order through the Toyota Special Service Tools (SSTs) hotline. A basic overview of the components of the program are outlined in the following sections.

Bosch Automotive Service Solutions will be facilitating this program on behalf of Toyota. Included in the Toyota Spray Wax Aftersales Support Program are approximately 20 tools. The tools will be available to order through the Toyota Special Service Tools (SSTs) hotline. A basic overview of the components of the program are outlined in the following sections.

Bosch Automotive Service Solutions will be facilitating this program on behalf of Toyota. Included in the Toyota Spray Wax Aftersales Support Program are approximately 20 tools. The tools will be available to order through the Toyota Special Service Tools (SSTs) hotline.

Please see T-SB-0304-17.

Please see T-SB-0304-17.

Previously, if the strap was cut or damaged, it was a non-serviceable part. APPLICABLE WARRANTY ? This repair is covered under the Toyota Basic Warranty. This warrantyis in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. ? Warranty application is limited to occurrence of the specified condition described in this bulletin

differential in 2WD that is not present during 4WD operation. Follow the Repair Procedure in this bulletin to address this condition. APPLICABLE WARRANTY ? This repair is covered under the Toyota Powertrain Warranty. This warranty is in effect for 60 months or 60,000 miles, whichever occurs first, from the vehicle?s in-service date. ? Warranty application is limited to occurrence of the specified condition described in this bulletin.

differential in 2WD that is not present during 4WD operation. Follow the Repair Procedure in this bulletin to address this condition. APPLICABLE WARRANTY ? This repair is covered under the Toyota Powertrain Warranty. This warranty is in effect for 60 months or 60,000 miles, whichever occurs first, from the vehicle?s in-service date. ? Warranty application is limited to occurrence of the specified condition described in this bulletin.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

*Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.

INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY."

The noise may be more noticeable when cross winds are present. Follow the procedure in this bulletin to address this condition.

Make sure to confirm that noise is coming from RH FR (No.1) Body Mount Bushing before proceeding.

when driving over uneven roads or bumps. Make sure to confirm that the noise is coming from the FR RH (No.1) Body Mount Bushing before proceeding.

speed bumps or with movement from loading and unloading the suspension. Follow the Repair Procedure in this bulletin to address this condition.

The noise may be more noticeable when cross winds are present. Follow the procedure in this bulletin to address this condition.

speed bumps or with movement from loading and unloading the suspension. Follow the Repair Procedure below to address this condition.

Some 2016 ? 2017 model year Tacoma vehicles may exhibit a squeak noise from the rear leaf spring when traveling over speed bumps or with movement from loading and unloading the suspension.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

T-SB-0103-16. The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

IF THE WHEELS ARE REPLACED OR REFINISHED BEFORE VEHICLE DELIVERY, IT IS IMPORTANT THAT THE TIRES REMAIN ON THE VEHICLE IN THE SAME LOCATION AND IN THE SAME DIRECTION OF ROTATION. PLEASE REFER TO THE FOLLOWING PROCEDURE TO ENSURE THAT THE ORIGINAL TIRES STAY IN THE SAME LOCATION ON THE VEHICLE."

model year Toyota vehicles.

model year Toyota vehicles.

Any previous printed versions of this bulletin should be discarded.

Any previous printed versions of this bulletin should be discarded.

frame, hole plugs are installed in certain locations of the frame during manufacturing. ? One of the hole plug styles allow water to drain from the bottom of the frame yet block water from entering. ? This one-way drain plug is located near a usable frame lift point. If the technician does not take note of the location of one-way drain plug, it may be easily crushed by the shop lift's arm.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

Provide Accessory lamp diagnostics and manufacturing date inspection information.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.