2016 Toyota Sienna TSBs

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

right-hand or left-hand side comes loose from the door channel during window operation. Follow the Repair Procedure in this bulletin to address this condition.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

right-hand or left-hand side comes loose from the door channel during window operation. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

coverage, including prospective coverage for repairs to certain sliding door parts but only those repairs that relate to internal functional concerns of those parts on certain 2011 - 2018 model year Sienna vehicles.

This Sienna Sliding Door Functional Inspection is one of multiple elements involved in a class action settlement. Refer to Customer Confidence Program ZKI for comprehensive information on the class action settlement and its other elements.

causing the power slide door to become inoperative. Follow the Repair Procedure in this bulletin to reduce this condition.

Upon customer request, the Inspection Procedure in this bulletin may be performed for a functional check of the slide door system.

center hinge has corroded, causing the power slide door to not fully open or close during operation. Follow the Inspection Procedure and Repair Procedure in this bulletin to address this condition.

center hinge has corroded, causing the slide door to become difficult to operate while opening or closing. Follow the Inspection and Repair Procedures in this bulletin to address this condition.

? Toyota has expanded the covered vehicle population. ? Toyota has extended the coverage period by one additional year. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to extend the warranty coverage for the power sliding door rear lock assemblies on certain 2011 ? 2018 model year Sienna vehicles.

certain 2011?2018 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

? Toyota has expanded the covered vehicle population. ? Toyota has extended the coverage period by one additional year. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to extend the warranty coverage for the sliding door front lock assemblies on certain 2011 ? 2018 model year Sienna vehicles.

T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

separated, causing the power sliding door to become inoperative. Follow the Repair Procedure in this bulletin to reduce this condition.

rear latches may not latch simultaneously due to corrosion on the latch lever pin of the front lock assembly. Additionally, some 2011 ? 2015 model year Sienna vehicles may exhibit a condition where the power slide door does not close properly due to internal corrosion in the latch switch of the rear lock assembly. Follow the procedures in this bulletin to address these conditions.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

certain 2011?2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

Blind Spot Monitor Warning message with Diagnostic Trouble Code (DTC) C1AB2 Short to Ground in Outer Mirror Indicator (Master) or C1AB3 Short to Ground in Outer Mirror Indicator (Slave) stored. Follow the Repair Procedure in this bulletin to address this condition.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

Blind Spot Monitor Warning message with Diagnostic Trouble Code (DTC) C1AB2 Short to Ground in Outer Mirror Indicator (Master) or C1AB3 Short to Ground in Outer Mirror Indicator (Slave) stored. Follow the Repair Procedure in this bulletin to address this condition.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

Blind Spot Monitor Warning message with Diagnostic Trouble Code (DTC) C1AB2 Short to Ground in Outer Mirror Indicator (Master) or C1AB3 Short to Ground in Outer Mirror Indicator (Slave) stored. Follow the Repair Procedure in this bulletin to address this condition.

operating the window.

The Dealer Letter for Warranty Enhancement Program ZH4 is now available on TIS.

certain 2011 ? 2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

simultaneously NOT latching due to corrosion on the latch lever pin of the front lock assembly. Additionally, some 2011 ? 2015 model year Sienna vehicles may exhibit power sliding door abnormal closing operation due to internal corrosion in the latch switch of the rear lock assembly.

On some vehicles, when Rapgard? is removed the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is NOT necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

Back Door (PBD) may exhibit a condition in which the back door latch does not release and the PBD cannot be opened from any switch (IP, key, back door), with one or both of the following conditions: * Excessive force required to operate the manual back door latch release lever * DTC B2250 present.

BLIND SPOT MONITOR WARNING MESSAGE WITH DIAGNOSTIC TROUBLE CODE (DTC) C1AB2 SHORT TO GROUND IN OUTER MIRROR INDICATOR (MASTER) OR C1AB3 SHORT TO GROUND IN OUTER MIRROR INDICATOR (SLAVE) STORED. FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THIS CONDITION.

THESE STAINS APPEAR TO BE UNDER THE CLEAR COAT (REPAINTING THIS AREA IS NOT NECESSARY). THE STAIN PATTERNS ARE USUALLY UNDER WRINKLES IN THE RAPGARD. THESE WRINKLES SOMETIMES TRAP WATER AND CAUSE THE PAINT TO STAIN FROM THE TRAPPED MOISTURE, ESPECIALLY ON HORIZONTAL SURFACES, SUCH AS THE HOOD, ROOF, AND TRUNK. STAINS CAN BE REMOVED BY HEATING THE STAINED SURFACE TO REMOVE THE TRAPPED MOISTURE.

IT'S MORE ROBUST DESIGN MAKES IT EASIER TO ADJUST AND HOLDS THE ADJUSTMENT IN PLACE REDUCING OR ELIMINATING INCORRECT SIGNALLING TO THE VMI AND OEM COMPUTER

BLIND SPOT MONITOR WARNING MESSAGE WITH DIAGNOSTIC TROUBLE CODE (DTC) C1AB2 SHORT TO GROUND IN OUTER MIRROR INDICATOR (MASTER) OR C1AB3 SHORT TO GROUND IN OUTER MIRROR INDICATOR (SLAVE) STORED. FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THIS CONDITION.

BLIND SPOT MONITOR WARNING MESSAGE WITH DIAGNOSTIC TROUBLE CODE (DTC) C1AB2 SHORT TO GROUND IN OUTER MIRROR INDICATOR (MASTER) OR C1AB3 SHORT TO GROUND IN OUTER MIRROR INDICATOR (SLAVE) STORED. FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THIS CONDITION.

IT'S MORE ROBUST DESIGN MAKES IT EASIER TO ADJUST AND HOLDS THE ADJUSTMENT IN PLACE REDUCING OR ELIMINATING INCORRECT SIGNALLING TO THE VMI AND OEM COMPUTER CONCERNING THE STATUS OF THE PASS. SIDE SLIDING DOOR

This is caused by the phone Hands Free volume being too low.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

In some instances, this condition causes the Panasonic head unit to reboot when the Bluetooth connection is initiated.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

In some instances, this condition causes the Panasonic head unit to reboot when the Bluetooth connection is initiated.

Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as ?ATX webserver is Down? or ?ATX error? will be displayed.

Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for echo or excessive background noise.

Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as ?ATX webserver is Down? or ?ATX error? will be displayed.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for Echo or excessive background noise.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

The Introduction has been updated to include new software changes. Some 2016 ? 2017 model year applicable vehicles equipped with Entune? Audio (version 01013E) / Entune? Audio Plus (version 010156 or 01015C) / Entune? Premium Audio (version 010171 or 010170 or 01017D) may exhibit one or more of the following conditions: ? Head unit rebooting at a specific location. ? Abnormal destination search operation. ? Rebooting caused by no songs on the USB connected iPhone. ? One time reboot after ACC-ON. ? Audio stays muted after the key is cycled.

The trail period of service is provided upon the vehicle purchase. Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as "ATX webserver is Down" or "ATX error" will be displayed.

(Lollipop) or later.

Please try again later.? If the following screen is seen; follow the directions below.

(Lollipop) or later.

Please try again later." If the following screen is seen, follow the directions below.

Click on the TIS tab, Diagnostics tab, Telematics tab, and the document is now located under the reference documents sections. This change has occurred to help speed up the updating process of this document.

The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.

Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for Echo or excessive background noise.

which can be performed to diagnose the condition.

Please try again later." If the following screen is seen; follow the directions below.

system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.

Please try again later.? If the following screen is seen; follow the directions below.

This is to promote safe driving practices and reduce the amount of distractions while driving. These lockouts can?t be deactivated or defeated through any settings. The following is a list of common lockouts, however, this is not a complete list of lockouts.

memory.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

or 01015C) / Entune Premium Audio (version 010171 or 010170 or 01017D) may exhibit one or more of the following conditions: *Head unit rebooting at a specific location. *Abnormal destination search operation. *Rebooting caused by no songs on the USB connected iPhone. *One time reboot after ACC-ON. *Audio stays muted after the key is cycled.

system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.

When performing PDS or installing the antenna pole for any other reason, inspect the antenna base for a hex-cut to determine if the following procedure is required.

PLEASE TRY AGAIN LATER." IF THE FOLLOWING SCREEN IS SEEN, FOLLOW THE DIRECTIONS BELOW.

WHEN PERFORMING PDS OR INSTALLING THE ANTENNA POLE FOR ANY OTHER REASON, INSPECT THE ANTENNA BASE FOR A HEX-CUT TO DETERMINE IF THE FOLLOWING PROCEDURE IS REQUIRED."

THE CUSTOMER'S IPHONE IS CONNECTED TO THE VEHICLE VIA BLUETOOTH. THE CUSTOMER MAY COMPLAIN OF THE FOLLOWING ISSUES: WHEN RECEIVING TWO INCOMING CALLS SIMULTANEOUSLY, BOTH CALLS ARE ENDED AUTOMATICALLY. ITUNES RADIO APP DOES NOT PLAY VIA BLUETOOTH AUDIO. PODCAST AND AUDIOBOOK MEDIA PLAYBACK IS INOPERATIVE VIA BLUETOOTH AUDIO.

SYSTEM WITH ANDROID PHONES RUNNING OS 4.4 OR LATER. CONDITION TENDS TO OCCUR TO CUSTOMERS WHO HAVE MANY PREVIOUS TEXT MESSAGES ON THEIR PHONES.

CURRENT MULTIMEDIA SYSTEMS ARE DESIGNED WITH THE ABILITY TO ADJUST BLUETOOTH SOUND QUALITY TO COMPENSATE FOR ECHO OR EXCESSIVE BACKGROUND NOISE.

CLICK ON THE TIS TAB, DIAGNOSTICS TAB, TELEMATICS TAB, AND THE DOCUMENT IS NOW LOCATED UNDER THE REFERENCE DOCUMENTS SECTIONS. THIS CHANGE HAS OCCURRED TO HELP SPEED UP THE UPDATING PROCESS OF THIS DOCUMENT. "

OR 01015C) / ENTUNE PREMIUM AUDIO (VERSION 010171 OR 010170 OR 01017D) MAY EXHIBIT ONE OR MORE OF THE FOLLOWING CONDITIONS: *HEAD UNIT REBOOTING AT A SPECIFIC LOCATION. *ABNORMAL DESTINATION SEARCH OPERATION. *REBOOTING CAUSED BY NO SONGS ON THE USB CONNECTED IPHONE. *ONE TIME REBOOT AFTER ACC-ON. *AUDIO STAYS MUTED AFTER THE KEY IS CYCLED.

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled.

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

If a level surface with a consistent plane is not available, use the Floor Slope Compensation Procedure in this service bulletin in conjunction with the appropriate model and model year Repair Manual instructions when adjusting the millimeter wave radar sensor.

If a level surface is not available, this tech tip should be used in conjunction with the repair manual to set the angle of the front millimeter wave radar sensor and reflector height before performing beam axis adjustment.

2011 ? 2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ?During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ?During power mode closing operation, the power sliding door cannot completely close and latch. ?The power mode closing operation of the power sliding door is inoperative. Although the power sliding door rear lock assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs relating to corrosion on the position sensor of the left and/or right power sliding door rear lock assembly that causes that door to exhibit one or more of the abnormal operations described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

on certain 2011?2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

on certain 2011?2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State of Charge (SOC) of the vehicle?s battery while in stock and assure proper State of Charge (SOC) at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, all dealers should check battery State of Charge (SOC) and recharge, if necessary, within 48 hours of delivery to customers.

T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

T-SB-0103-16 and T-SB-0337-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 and T-SB-0337-17 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2016 ? 2018 model year vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (version 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled

T-SB-0103-16 and T-SB-0337-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 and T-SB-0337-17 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2016 ? 2018 model year vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (version 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

due to the PSD 25 Amp fuse becoming open. APPLICABLE WARRANTY: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for unlimited mileage and unlimited months of service. Warranty application is limited to occurrence of the specified condition described in this bulletin.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

Customer feedback indicates the following areas deserve special attention when performing PDS: ? Careful inspection for paint chips/scratches and body dents/dings. ? Proper operation of electrical accessories (including interior light, clock, and radio reset). ? Interior cleanliness ? Proper function of mechanical systems. Customer retention and proper maintenance of vehiucles has been a major focus for Toyota. To help remind customers that regular oil changes are essential to the proper maintence of their vehicle, installing a first oil change reminder sticker is required prior to delivery. By doing this, customers will be reminded to return to a dealership for their first oil change. Your current oil change reminder sticker may be used. (See PDS Check Sheet item 9 of ?Final Inspection & Cleaning.?) A new PDS Check Sheet has been developed for the 2016 model year Sienna. Some check points have been added, expanded, or clarified. Bulleting are available for items in bold type.

When the Short Pin is reinstalled, the Parking Assist Monitor System will be operative, but it cannot display guidelines to assist parking operation because the center position is not recognized by the steering angle sensor. Please initialize the Parking Assist Monitor System after installing the Short Pin during Pre-Delivery Service (PDS).

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION."

THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE. AS A MATTER OF POLICY, TOYOTA DOES NOT PROVIDE BATTERY WARRANTY COVERAGE FOR DISCHARGED AND/OR FAILED BATTERIES DUE TO LACK OF MAINTENANCE. IT IS THE DEALERS RESPONSIBILITY TO MAINTAIN THE SPECIFIED STATE OF CHARGE (SOC) OF THE VEHICLES BATTERY WHILE IN STOCK AND ASSURE PROPER STATE OF CHARGE (SOC) AT DELIVERY. TO ELIMINATE CUSTOMER SERVICE CONCERNS DUE TO AN UNDERCHARGED BATTERY DURING THE FIRST FEW WEEKS OF OWNERSHIP, ALL DEALERS SHOULD CHECK BATTERY STATE OF CHARGE (SOC) AND RECHARGE, IF NECESSARY, WITHIN 48 HOURS OF DELIVERY TO CUSTOMERS."

CUSTOMER FEEDBACK INDICATES THE FOLLOWING AREAS DESERVE SPECIAL ATTENTION WHEN PERFORMING PDS: CAREFUL INSPECTION FOR PAINT CHIPS/SCRATCHES AND BODY DENTS/DINGS. PROPER OPERATION OF ELECTRICAL ACCESSORIES (INCLUDING INTERIOR LIGHT, CLOCK, AND RADIO RESET). INTERIOR CLEANLINESS PROPER FUNCTION OF MECHANICAL SYSTEMS. CUSTOMER RETENTION AND PROPER MAINTENANCE OF VEHIUCLES HAS BEEN A MAJOR FOCUS FOR TOYOTA. TO HELP REMIND CUSTOMERS THAT REGULAR OIL CHANGES ARE ESSENTIAL TO THE PROPER MAINTENCE OF THEIR VEHICLE, INSTALLING A FIRST OIL CHANGE REMINDER STICKER IS REQUIRED PRIOR TO DELIVERY. BY DOING THIS, CUSTOMERS WILL BE REMINDED TO RETURN TO A DEALERSHIP FOR THEIR FIRST OIL CHANGE. YOUR CURRENT OIL CHANGE REMINDER STICKER MAY BE USED. (SEE PDS CHECK SHEET ITEM 9 OF FINAL INSPECTION & CLEANING.) A NEW PDS CHECK SHEET HAS BEEN DEVELOPED FOR THE 2016 MODEL YEAR SIENNA. SOME CHECK POINTS HAVE BEEN ADDED, EXPANDED, OR CLARIFIED. BULLETING ARE AVAILABLE FOR ITEMS IN BOLD TYPE. "

WHEN THE SHORT PIN IS REINSTALLED, THE PARKING ASSIST MONITOR SYSTEM WILL BE OPERATIVE, BUT IT CANNOT DISPLAY GUIDELINES TO ASSIST PARKING OPERATION BECAUSE THE CENTER POSITION IS NOT RECOGNIZED BY THE STEERING ANGLE SENSOR. PLEASE INITIALIZE THE PARKING ASSIST MONITOR SYSTEM AFTER INSTALLING THE SHORT PIN DURING PRE-DELIVERY SERVICE (PDS).

PRODUCED BY NXP AND ASSEMBLED INTO AIRBAG SENSOR SUPPLIED BY DENSO INTERNATIONAL AMERICA, INC. THIS DELAMINATION ISSUE MANIFESTS ITSELF AS AN OPEN CIRCUIT WITHIN THE SENSOR, CAUSING A DTC TO BE SET ON THE VEHICLE ALONG WITH A DECLARING AIRBAG LIGHT.

Please see T-SB-0057-18.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0045-22

?Abnormal Operation? condition from the rear differential front coupling. In some cases, even an ?AWD System Message? with or without a DTC may be present with or without other conditions present.

Please see T-SB-0004-21.

Please see T-SB-0012-21.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0010-20.

Please see T-SB-0003-20.

rear coupling unit while driving. This condition can be caused by utilizing an improper towing method when transporting vehicles.

Please see T-SB-0080-19.

Please see T-SB-0033-18.

Please follow the Repair Procedure in this bulletin to address this condition.

Please follow the Repair Procedure in this bulletin to address the condition.

Please see T-SB-0134-16.

This condition has been remedied, and DCM activation utilizing Techstream can now be resumed.

This is a known condition and will be remedied in the near future. Please discontinue DCM activations utilizing Techstream until further notice.

Toyota accessory overhead DVD player.

may not latch correctly after being returned from the stowed position. The front leg/legs may be misaligned with the striker causing it to be in front of, behind or contacting the striker, but not latched correctly.

Please see T-SB-0279-17.

PLEASE FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THE CONDITION.

PLEASE FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THIS CONDITION.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the power sliding door cable sub-assembly. Although the power sliding door cable sub-assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to the power sliding door cable sub-assembly. Only those repairs that are related to internal functional concerns of the power sliding door cable sub-assembly that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

(Vehicles equipped with power sliding doors ONLY). In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the power sliding door cable sub-assembly. Although the power sliding door cable sub-assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the power sliding door cable sub-assembly. Only those repairs that are related to internal functional concerns of the power sliding door cable sub-assembly that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the fuel filler door hinge and pin. Although the fuel filler door hinge and pin are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to the fuel filler door hinge and pin. Only those repairs that are related to internal functional concerns of the fuel filler door hinge and pin that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the fuel filler door hinge and pin. Although the fuel filler door hinge and pin are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the fuel filler door hinge and pin. Only those repairs that are related to internal functional concerns of the fuel filler door hinge and pin that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Specific information for Region support is provided below. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

against the vehicle body, which may prevent the driver side slide door from opening. This condition may be caused by a broken fuel lid door hinge. Follow the Repair Procedure in this bulletin to address this condition.

approved a proposed settlement regarding sliding doors on certain 2011-2018 model year Sienna vehicles. ? The proposed settlement has yet to receive final approval by the court. However, the proposed settlement allows Toyota to implement the Customer Confidence Program (as outlined in the settlement agreement) in advance of the proposed settlement becoming final. Accordingly, Toyota has decided to implement certain components of the Customer Confidence Program in advance of final approval. These components are listed below and Toyota estimates that they will be available starting in April 2019.1 At that time, Toyota will issue a notice to all dealers advising them that these components have become available. Pursuant to the proposed settlement?s Customer Confidence Program: o Coverage for repairs to the power sliding door cable sub-assembly, sliding door center hinge assembly, and fuel door will be available for 10 years from the subject vehicles date of first use, regardless of mileage. o Warranty Enhancement Program ZH4 will be expanded to include certain 2016 ? 2018 model year Sienna vehicles. o Warranty Enhancement Program ZH5 will be expanded to include certain 2015 ? 2018 model year Sienna vehicles. o Warranty Enhancement Programs ZH4 and ZH5, which are applicable for nine years from the subject vehicles date of first use regardless of mileage, will be extended by one additional year regardless of mileage. ? The court has ordered that the 3rd Party Settlement Notice Administrator begin notifying class members, including by direct mail notice (see images on next page), on March 1, 2019, to inform current and former vehicle owners and lessees of the proposed settlement.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

? The Parts Information section has been updated. Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle's systems and components. Any problems that are found should be corrected immediately.

THE FOLLOWING GUIDELINES SHOULD BE PERFORMED TO MINIMIZE VEHICLE COMPONENT/PART DEGRADATION DUE TO EXTENDED VEHICLE STORAGE CONDITIONS. LONG-TERM STORAGE CAN AFFECT A VEHICLES SYSTEMS AND COMPONENTS. ANY PROBLEMS THAT ARE FOUND SHOULD BE CORRECTED IMMEDIATELY."

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.

aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible.

The following update modifies the system functionality while the vehicle is in motion, improving customer experience. New software is available to address the following: ? Phone keypad unlocked while vehicle is in motion ? Contact list unlocked while vehicle is in motion ? Bluetooth connected phone switching while vehicle is in motion ? Navigation transition improvements (if equipped) ? Revised BT-Audio help pop-up ? Call history list call function improvements

Brake vibration can occur at any time if improper torque is applied to lug nuts. Even one lug nut over or under torqued can cause vibration.

T-SB-0045-14. * Applicability has been updated to include 2018 model year Sienna vehicles. * The entire bulletin has been updated. Service Bulletin No. T-SB-0045-14 is obsolete and any printed versions should be discarded. Some 2011 - 2018 model year Sienna vehicles may exhibit a vibration/pulsation from the front brakes that can be felt in the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.

even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface

the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.

ANY PREVIOUS PRINTED VERSIONS OF THIS BULLETIN SHOULD BE DISCARDED. SOME 2011 2016 MODEL YEAR SIENNA VEHICLES MAY EXHIBIT A VIBRATION/PULSATION FROM THE FRONT BRAKES THAT CAN BE FELT IN THE BRAKE PEDAL WHILE LIGHTLY APPLYING THE BRAKE PEDAL. NEW FRONT BRAKE PADS AND A NEW FIELD FIX REPAIR PROCEDURE HAVE BEEN DEVELOPED TO IMPROVE THIS CONDITION. "

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

(ECM/PCM Engine Off Timer Performance) present. The Engine Control Module (ECM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.

inside the Oxygen Sensor wiring harness caused by vehicle vibration during normal operation. If this occurs, the vehicle will illuminate the check engine light.

the Oxygen Sensor wiring harness caused by vehicle vibration during normal operation. If this occurs, the vehicle will illuminate the check engine light.

the Oxygen Sensor wiring harness caused by vehicle vibration during normal operation. If this occurs, the vehicle will illuminate the check engine light.

the Oxygen Sensor wiring harness caused by vehicle vibration during normal operation. If this occurs, the vehicle will illuminate the check engine light.

the Oxygen Sensor wiring harness caused by vehicle vibration during normal operation. If this occurs, the vehicle will illuminate the check engine light.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

INSIDE THE OXYGEN SENSOR WIRING HARNESS CAUSED BY VEHICLE VIBRATION DURING NORMAL OPERATION. IF THIS OCCURS, THE VEHICLE WILL ILLUMINATE THE CHECK ENGINE LIGHT.

THE OXYGEN SENSOR WIRING HARNESS CAUSED BY VEHICLE VIBRATION DURING NORMAL OPERATION. IF THIS OCCURS, THE VEHICLE WILL ILLUMINATE THE CHECK ENGINE LIGHT.

THE OXYGEN SENSOR WIRING HARNESS CAUSED BY VEHICLE VIBRATION DURING NORMAL OPERATION. IF THIS OCCURS, THE VEHICLE WILL ILLUMINATE THE CHECK ENGINE LIGHT.

THE OXYGEN SENSOR WIRING HARNESS CAUSED BY VEHICLE VIBRATION DURING NORMAL OPERATION. IF THIS OCCURS, THE VEHICLE WILL ILLUMINATE THE CHECK ENGINE LIGHT.

INSIDE THE OXYGEN SENSOR WIRING HARNESS CAUSED BY VEHICLE VIBRATION DURING NORMAL OPERATION. IF THIS OCCURS, THE VEHICLE WILL ILLUMINATE THE CHECK ENGINE LIGHT.

INSIDE THE OXYGEN SENSOR WIRING HARNESS CAUSED BY VEHICLE VIBRATION DURING NORMAL OPERATION. IF THIS OCCURS, THE VEHICLE WILL ILLUMINATE THE CHECK ENGINE LIGHT.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

Please see T-SB-0304-17.

Please see T-SB-0304-17.

of regular maintenance

The first year of service is provided in the vehicle purchase price. Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.

exhibit an inoperative forward/rearward adjustment function. Upon closer inspection it may be noticed that the Seat Track Adjusting Handle has become disengaged from the locking levers. APPLICABLE WARRANTY: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to occurrence of the specified condition described in this bulletin.

the rear seat latches (floor area). This condition is present while driving over rough or bumpy roads. Upon further inspection, after removal of the LH 2nd row seat, the rear inboard and outboard strikers may show signs of the coating peeling off as shown in Fig.2 and Fig.3.

The first year of service is provided in the vehicle purchase price. Once the subscription has lapsed the DCM will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.

the vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the proper operation of the Smart Key system prior to vehicle delivery.

The first year of service is provided in the vehicle purchase price. Once the subscription has lapsed the DCM will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.

the vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the proper operation of the Smart Key system prior to vehicle delivery.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

Adding stop leak products to the A/C system is not a recommended or approved Toyota repair process. During A/C service, moisture enters the A/C system, and can react with the previously added A/C stop leak, forming a gelatinous substance. The gel substance that forms can cause the A/C compressor to bind and or seize.

? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

*Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.

INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY."

THIS SB NOTIFIES THE TECHNICIANS TO ENSURE THE TORQUE SPECIFICATIONS FOR THE STEERING EXTENSION HAVE BEEN COMPLIED WITH AT THE FACTORY. THIS WILL BRING THE VAN INTO CONFORMANCE WITH VMI UPDATED PROCESSES

THIS SB NOTIFIES THE TECHNICIANS TO ENSURE THE TORQUE SPECIFICATIONS FOR THE STEERING EXTENSION HAVE BEEN COMPLIED WITH AT THE FACTORY. THIS WILL BRING THE VAN INTO CONFORMANCE WITH VMI UPDATED PROCESSES

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match the radio station that is playing.?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi/km?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010145), Entune? Audio Plus (version 010161), Entune? Premium Audio (version 010189), or earlier may exhibit one of the following conditions: ?Map will not display after it has been reprogrammed from the map micro SD card. Updated system software is now

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match the radio station that is playing.?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi/km?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010145), Entune? Audio Plus (version 010161), Entune? Premium Audio (version 010189), or earlier may exhibit one of the following conditions: ?Map will not display after it has been reprogrammed from the map micro SD card. Updated system software is now avail

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match radio station that is playing. ?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Updated system software is now available to address these conditions. Follow the Software Update Procedure in this bulletin to install the latest software version.

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match radio station that is playing. ?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative.

T-SB-0279-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0279-17 is obsolete and ANY printed versions should be discarded. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ? Head unit reboots intermittently ? Half blank screen appears when on the maintenance screen and shifting to Reverse ? Screen freezes during an incoming phone call ? Incorrect time displays on the diagnostic menu ? Radio station information does not match radio station that is playing ? Abnormal playlist browsing operation ? Mute stays enabled after key cycle ? ?Search along my route? is inoperative ? Traffic data scales improperly ? Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?) ? MID compass does not match navigation screen when switching to North up ? Navigation does not match MID when switching from miles to kilometers ? Speed limit is blank on navigation screen ? Go button on VR screen is inoperative

(ATF) level at normal vehicle operating temperature. Note: The following adjustment procedures are for U660E/F and U760E/F transmissions.

the vehicle to Reverse (?R? position). The owner?s manual describes the ability to customize the outer mirror positions when the vehicle is in reverse.

shifting the vehicle to Reverse (?R? position). The owner?s manual describes the ability to customize the outer mirror positions when the vehicle is in reverse.

model year Toyota vehicles.

model year Toyota vehicles.

Any previous printed versions of this bulletin should be discarded.

This allows for more amperage to draw the Powerkneel up allowing the up-limit switch to be tripped consistently. If the up limit switch is not engaged, a vehicle may not come out of park or the conversion may not operate properly next time it is deployed

This allows for more amperage to draw the Powerkneel up allowing the up-limit switch to be tripped consistently. If the up limit switch is not engaged, a vehicle may not come out of park or the conversion may not operate properly next time it is deployed

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

T-SB-0103-16. The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

IF THE WHEELS ARE REPLACED OR REFINISHED BEFORE VEHICLE DELIVERY, IT IS IMPORTANT THAT THE TIRES REMAIN ON THE VEHICLE IN THE SAME LOCATION AND IN THE SAME DIRECTION OF ROTATION. PLEASE REFER TO THE FOLLOWING PROCEDURE TO ENSURE THAT THE ORIGINAL TIRES STAY IN THE SAME LOCATION ON THE VEHICLE."

on the big end of the outboard front axle shaft joint. Follow the Repair Procedure in this bulletin to address the condition.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

ON THE BIG END OF THE OUTBOARD FRONT AXLE SHAFT JOINT. FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THE CONDITION.