2014 Toyota Sienna TSBs

Please see T-SB-0057-18.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

?Abnormal Operation? condition from the rear differential front coupling. In some cases, even an ?AWD System Message? with or without a DTC may be present with or without other conditions present.

Please see T-SB-0004-21.

Please see T-SB-0012-21.

Please see T-SB-0044-16.

Please see T-SB-0063-20.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0010-20.

rear coupling unit while driving. This condition can be caused by utilizing an improper towing method when transporting vehicles.

Please see T-SB-0080-19.

Please see T-SB-0118-15.

style lower seat cushion has excessive up and down movement. While some seat movement is a normal characteristic of the design, this bulletin will help identify excessive movement and provide steps to address this condition.

Please see T-SB-0033-18.

Please follow the Repair Procedure in this bulletin to address this condition.

Please follow the Repair Procedure in this bulletin to address the condition.

Please see T-SB-0118-15.

satisfaction.

correct pulling complaints.

slide function becomes inoperative due to plastic spacer interference in the lift mechanism. The seat lift mechanism has been improved to address this condition.

Please see T-SB-0134-16.

Once the system is reset, all previously registered keys will be erased.

Once the system is reset, all previously registered keys will be erased.

2017.

This condition has been remedied, and DCM activation utilizing Techstream can now be resumed.

Please see T-SB-0118-15.

This is a known condition and will be remedied in the near future. Please discontinue DCM activations utilizing Techstream until further notice.

Please see T-SB-0054-13.

10,000 miles for most vehicles that require this oil. With this change, the following should be noted

Instances) instead of the native Apple Podcast application.

Please see T-SB-0185-13.

seat cushion has excessive up and down movement. While some seat movement is a normal characteristic of the design, this bulletin will help identify excessive movement and provide steps to address this condition.

A watermark has been added to the Dealer Letter to indicate that E0K expired on May 31, 2017.

the rear of the vehicle while driving over rough road surfaces when the seats are empty in the upright latched position. If the 3rd row seats are stowed, the noise is no longer present.

PLEASE FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THE CONDITION.

PLEASE SEE T-SB-0118-15.

STYLE LOWER SEAT CUSHION HAS EXCESSIVE UP AND DOWN MOVEMENT. WHILE SOME SEAT MOVEMENT IS A NORMAL CHARACTERISTIC OF THE DESIGN, THIS BULLETIN WILL HELP IDENTIFY EXCESSIVE MOVEMENT AND PROVIDE STEPS TO ADDRESS THIS CONDITION.

PLEASE FOLLOW THE REPAIR PROCEDURE IN THIS BULLETIN TO ADDRESS THIS CONDITION.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

right-hand or left-hand side comes loose from the door channel during window operation. Follow the Repair Procedure in this bulletin to address this condition.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

right-hand or left-hand side comes loose from the door channel during window operation. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

coverage, including prospective coverage for repairs to certain sliding door parts but only those repairs that relate to internal functional concerns of those parts on certain 2011 - 2018 model year Sienna vehicles.

This Sienna Sliding Door Functional Inspection is one of multiple elements involved in a class action settlement. Refer to Customer Confidence Program ZKI for comprehensive information on the class action settlement and its other elements.

causing the power slide door to become inoperative. Follow the Repair Procedure in this bulletin to reduce this condition.

Upon customer request, the Inspection Procedure in this bulletin may be performed for a functional check of the slide door system.

center hinge has corroded, causing the power slide door to not fully open or close during operation. Follow the Inspection Procedure and Repair Procedure in this bulletin to address this condition.

center hinge has corroded, causing the slide door to become difficult to operate while opening or closing. Follow the Inspection and Repair Procedures in this bulletin to address this condition.

? Toyota has expanded the covered vehicle population. ? Toyota has extended the coverage period by one additional year. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to extend the warranty coverage for the power sliding door rear lock assemblies on certain 2011 ? 2018 model year Sienna vehicles.

certain 2011?2018 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

? Toyota has expanded the covered vehicle population. ? Toyota has extended the coverage period by one additional year. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to extend the warranty coverage for the sliding door front lock assemblies on certain 2011 ? 2018 model year Sienna vehicles.

T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

separated, causing the power sliding door to become inoperative. Follow the Repair Procedure in this bulletin to reduce this condition.

Please see link references of video for example condition and diagnosis instruction.

rear latches may not latch simultaneously due to corrosion on the latch lever pin of the front lock assembly. Additionally, some 2011 ? 2015 model year Sienna vehicles may exhibit a condition where the power slide door does not close properly due to internal corrosion in the latch switch of the rear lock assembly. Follow the procedures in this bulletin to address these conditions.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

certain 2011?2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

Please see link references of video for example condition.

The Dealer Letter for Warranty Enhancement Program ZH5 is now available on TIS.

The Dealer Letter for Warranty Enhancement Program ZH4 is now available on TIS.

certain 2011 ? 2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.

simultaneously NOT latching due to corrosion on the latch lever pin of the front lock assembly. Additionally, some 2011 ? 2015 model year Sienna vehicles may exhibit power sliding door abnormal closing operation due to internal corrosion in the latch switch of the rear lock assembly.

quenching process during manufacturing.

On some vehicles, when Rapgard? is removed the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is NOT necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

Back Door (PBD) may exhibit a condition in which the back door latch does not release and the PBD cannot be opened from any switch (IP, key, back door), with one or both of the following conditions: * Excessive force required to operate the manual back door latch release lever * DTC B2250 present.

the mirror glass reflective material. The mirror glass assembly has been updated to address this condition.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

the mirror glass reflective material. The mirror glass assembly has been updated to address this condition.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

THESE STAINS APPEAR TO BE UNDER THE CLEAR COAT (REPAINTING THIS AREA IS NOT NECESSARY). THE STAIN PATTERNS ARE USUALLY UNDER WRINKLES IN THE RAPGARD. THESE WRINKLES SOMETIMES TRAP WATER AND CAUSE THE PAINT TO STAIN FROM THE TRAPPED MOISTURE, ESPECIALLY ON HORIZONTAL SURFACES, SUCH AS THE HOOD, ROOF, AND TRUNK. STAINS CAN BE REMOVED BY HEATING THE STAINED SURFACE TO REMOVE THE TRAPPED MOISTURE.

PLEASE SEE LINK REFERENCES OF VIDEO FOR EXAMPLE CONDITION.

IT'S MORE ROBUST DESIGN MAKES IT EASIER TO ADJUST AND HOLDS THE ADJUSTMENT IN PLACE REDUCING OR ELIMINATING INCORRECT SIGNALLING TO THE VMI AND OEM COMPUTER

PLEASE SEE LINK REFERENCES OF VIDEO FOR EXAMPLE CONDITION AND DIAGNOSIS INSTRUCTION.

IT'S MORE ROBUST DESIGN MAKES IT EASIER TO ADJUST AND HOLDS THE ADJUSTMENT IN PLACE REDUCING OR ELIMINATING INCORRECT SIGNALLING TO THE VMI AND OEM COMPUTER CONCERNING THE STATUS OF THE PASS. SIDE SLIDING DOOR

Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as ?ATX webserver is Down? or ?ATX error? will be displayed.

Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as ?ATX webserver is Down? or ?ATX error? will be displayed.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

The trail period of service is provided upon the vehicle purchase. Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as "ATX webserver is Down" or "ATX error" will be displayed.

(Lollipop) or later.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

customer?s iPhone is operating on iOS9 firmware The customer?s iPhone is connected to the vehicle via Bluetooth. If the vehicle is equipped with a Fujitsu-Ten brand head unit, the customer may complain of one or more of the following: When playing media via Bluetooth audio and pressing the ?Pause? button on the phone, media playback pauses for one second before resuming playback. Yelp searches return an error when search criteria includes a special character, e.g. !,$,#. If the vehicle is equipped with a Pioneer brand head unit, the customer may complain of one or more of the following: The customer?s iPhone does not support the album image feature. When playing media via Bluetooth audio, one or more of a number of play/pause issues occur.

010171) Entune? Premium Audio (version 01085) may exhibit one or more of the following conditions: Bluetooth sometimes disconnects with Android? phones Bluetooth disconnects with iPhone 4 when connected to USB Radio reboots with heavy radio load condition (e.g., dual map and POIs ON and Entune? Audio music ON and multiple destinations set) (Entune? Premium Audio only) Radio reboots after completing a navigation route by voice command system and pressing Talk Switch (Entune? Premium Audio only)

(Lollipop) or later.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.

When performing PDS or installing the antenna pole for any other reason, inspect the antenna base for a hex-cut to determine if the following procedure is required.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

customer?s iPhone is operating on iOS9 firmware The customer?s iPhone is connected to the vehicle via Bluetooth. If the vehicle is equipped with a Fujitsu-Ten brand head unit, the customer may complain of one or more of the following: When playing media via Bluetooth audio and pressing the ?Pause? button on the phone, media playback pauses for one second before resuming playback. Yelp searches return an error when search criteria includes a special character, e.g. !,$,#. If the vehicle is equipped with a Pioneer brand head unit, the customer may complain of one or more of the following: The customer?s iPhone does not support the album image feature. When playing media via Bluetooth audio, one or more of a number of play/pause issues occur.

010171) Entune? Premium Audio (version 01085) may exhibit one or more of the following conditions: Bluetooth sometimes disconnects with Android? phones Bluetooth disconnects with iPhone 4 when connected to USB Radio reboots with heavy radio load condition (e.g., dual map and POIs ON and Entune? Audio music ON and multiple destinations set) (Entune? Premium Audio only) Radio reboots after completing a navigation route by voice command system and pressing Talk Switch (Entune? Premium Audio only)

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

This feature does work with the in-vehicle audio system either via Bluetooth or by USB cable. Details on how to access this feature are described below.

When a customer is paired by Bluetooth Hands Free and they make a Facetime Audio call the vehicle radio will treat it as a typical Bluetooth phone call. Because Facetime works differently than a typical phone call, the in-vehicle experience may not meet the customer?s expectations.

After entering into a contract, registration of an 8-digit XM Radio ID is required. This 8-digit XM Radio ID is found by turning to channel ?0? of the satellite radio.

The ?delete? soft button on the multi-information display is greyed out and not selectable.

to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

memory.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

systems.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY. "

REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.

THE CUSTOMER'S IPHONE IS CONNECTED TO THE VEHICLE VIA BLUETOOTH. THE CUSTOMER MAY COMPLAIN OF THE FOLLOWING ISSUES: WHEN RECEIVING TWO INCOMING CALLS SIMULTANEOUSLY, BOTH CALLS ARE ENDED AUTOMATICALLY. ITUNES RADIO APP DOES NOT PLAY VIA BLUETOOTH AUDIO. PODCAST AND AUDIOBOOK MEDIA PLAYBACK IS INOPERATIVE VIA BLUETOOTH AUDIO.

REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY. "

The settlement includes Toyota?s agreement to provide a Customer Support Program (?CSP?) for 2002-2019 model year (MY) vehicles originally equipped with certain Takata airbag inflators or repaired under a recall with Takata airbag inflators to provide coverage for repairs of the airbag inflator contained in the airbag module. This CSP letter is to help clarify how to administer this coverage in accordance with the settlement. This is NOT a recall or a campaign, but is provided to reassure owners that Toyota stands behind the reliability of our vehicles.

If a level surface with a consistent plane is not available, use the Floor Slope Compensation Procedure in this service bulletin in conjunction with the appropriate model and model year Repair Manual instructions when adjusting the millimeter wave radar sensor.

If a level surface is not available, this tech tip should be used in conjunction with the repair manual to set the angle of the front millimeter wave radar sensor and reflector height before performing beam axis adjustment.

2011 ? 2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ?During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ?During power mode closing operation, the power sliding door cannot completely close and latch. ?The power mode closing operation of the power sliding door is inoperative. Although the power sliding door rear lock assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs relating to corrosion on the position sensor of the left and/or right power sliding door rear lock assembly that causes that door to exhibit one or more of the abnormal operations described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

on certain 2011?2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

on certain 2011?2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

on certain 2011?2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

due to the PSD 25 Amp fuse becoming open. APPLICABLE WARRANTY: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for unlimited mileage and unlimited months of service. Warranty application is limited to occurrence of the specified condition described in this bulletin.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

FCC regulations require the radar sensor to be temporarily inactive while the vehicle is stopped. Due to a program error in the Driving Support ECU, if the radar sensor is inactive for 10 seconds or more, the PCS may not reactivate on certain 2011-2014 Model Year Sienna vehicles equipped with PCS.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

on certain 2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.

When the Short Pin is reinstalled, the rear view monitor system will be operative, but it cannot display guidelines to assist parking operation because the center position is not recognized by the steering angle sensor. Please initialize the rear view monitor system after installing the Short Pin during Pre-Delivery Service (PDS).

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

Safety Connect system is in ?Shelled Mode? with a green LED illuminated prior to delivering the vehicle. Occasionally settings in the Data Communication Module (in-vehicle DCM), or on the network may prevent the ?Shelled Mode? status. In these potential cases, the vehicle is likely to be in ?Shipping Mode? and a red LED may be detected with or without a DTC.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION."

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the power sliding door cable sub-assembly. Although the power sliding door cable sub-assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to the power sliding door cable sub-assembly. Only those repairs that are related to internal functional concerns of the power sliding door cable sub-assembly that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

(Vehicles equipped with power sliding doors ONLY). In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the power sliding door cable sub-assembly. Although the power sliding door cable sub-assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the power sliding door cable sub-assembly. Only those repairs that are related to internal functional concerns of the power sliding door cable sub-assembly that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the fuel filler door hinge and pin. Although the fuel filler door hinge and pin are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to the fuel filler door hinge and pin. Only those repairs that are related to internal functional concerns of the fuel filler door hinge and pin that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the fuel filler door hinge and pin. Although the fuel filler door hinge and pin are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the fuel filler door hinge and pin. Only those repairs that are related to internal functional concerns of the fuel filler door hinge and pin that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Specific information for Region support is provided below. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

against the vehicle body, which may prevent the driver side slide door from opening. This condition may be caused by a broken fuel lid door hinge. Follow the Repair Procedure in this bulletin to address this condition.

approved a proposed settlement regarding sliding doors on certain 2011-2018 model year Sienna vehicles. ? The proposed settlement has yet to receive final approval by the court. However, the proposed settlement allows Toyota to implement the Customer Confidence Program (as outlined in the settlement agreement) in advance of the proposed settlement becoming final. Accordingly, Toyota has decided to implement certain components of the Customer Confidence Program in advance of final approval. These components are listed below and Toyota estimates that they will be available starting in April 2019.1 At that time, Toyota will issue a notice to all dealers advising them that these components have become available. Pursuant to the proposed settlement?s Customer Confidence Program: o Coverage for repairs to the power sliding door cable sub-assembly, sliding door center hinge assembly, and fuel door will be available for 10 years from the subject vehicles date of first use, regardless of mileage. o Warranty Enhancement Program ZH4 will be expanded to include certain 2016 ? 2018 model year Sienna vehicles. o Warranty Enhancement Program ZH5 will be expanded to include certain 2015 ? 2018 model year Sienna vehicles. o Warranty Enhancement Programs ZH4 and ZH5, which are applicable for nine years from the subject vehicles date of first use regardless of mileage, will be extended by one additional year regardless of mileage. ? The court has ordered that the 3rd Party Settlement Notice Administrator begin notifying class members, including by direct mail notice (see images on next page), on March 1, 2019, to inform current and former vehicle owners and lessees of the proposed settlement.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

The federal government issues caf (Corporate Average Fuel Economy) credits to vehicle manufacturers that implement new technologies that reduce the carbon footprint of the vehicles they produce. GHC Logic technology works by automatically operating the HVAC system in REC mode when certain operating conditions are met, improving the A/C systems cooling efficiency and reducing the vehicle's C02 emissions.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

Greenhouse Gas Logic (GHG) has been implemented on Toyota A/C Systems to reduce tailpipe emissions. The Federal government issues CAF (Corporate Average Fuel Economy) credits to vehicle manufacturers that implement new technologies that reduce the carbon footprint of the vehicles they produce. GHG Logic technology works by automatically operating the HVAC system in REC mode when certain conditions are met, improving the A/C system cooling efficiency and reducing the vehicle's CO2 tailpipe emissions.

The federal government issues caf (Corporate Average Fuel Economy) credits to vehicle manufacturers that implement new technologies that reduce the carbon footprint of the vehicles they produce. GHC Logic technology works by automatically operating the HVAC system in REC mode when certain operating conditions are met, improving the A/C systems cooling efficiency and reducing the vehicle's C02 emissions.

obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.

? The Parts Information section has been updated. Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

Please see T-SB-0304-17.

Please see T-SB-0304-17.

of regular maintenance

The first year of service is provided in the vehicle purchase price. Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.

exhibit an inoperative forward/rearward adjustment function. Upon closer inspection it may be noticed that the Seat Track Adjusting Handle has become disengaged from the locking levers. APPLICABLE WARRANTY: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to occurrence of the specified condition described in this bulletin.

the rear seat latches (floor area). This condition is present while driving over rough or bumpy roads. Upon further inspection, after removal of the LH 2nd row seat, the rear inboard and outboard strikers may show signs of the coating peeling off as shown in Fig.2 and Fig.3.

The first year of service is provided in the vehicle purchase price. Once the subscription has lapsed the DCM will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.

vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the proper operation of the Smart Key system prior to vehicle delivery.

Safety Connect is a vehicle option which requires a subscription fee for the system to be active. The first year of service is provided in the vehicle purchase price. Once the subscription has lapsed the DCM will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.

The first year of service is provided in the vehicle purchase price. Once the subscription has lapsed the DCM will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.

vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the proper operation of the Smart Key system prior to vehicle delivery.

vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the proper operation of the Smart Key system prior to vehicle delivery.

To help remind customers that regular oil changes are essential to the proper maintenance of their vehicle, installing a first oil change reminder sticker is required prior to delivery. By doing this, customers will be reminded to return to a dealership for their first oil change. Your current oil change reminder sticker may be used. (See PDS Check Sheet item 9 of ?Final Inspection & Cleaning.?) A new PDS Check Sheet has been developed for the 2014 model year Sienna. Some check points have been added, expanded, or clarified. Bulletins are available for items in bold type.

performance.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.

aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible.

T-SB-0045-14. * Applicability has been updated to include 2018 model year Sienna vehicles. * The entire bulletin has been updated. Service Bulletin No. T-SB-0045-14 is obsolete and any printed versions should be discarded. Some 2011 - 2018 model year Sienna vehicles may exhibit a vibration/pulsation from the front brakes that can be felt in the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.

even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface

FCC regulations require the radar sensor to be temporarily inactive while the vehicle is stopped. Due to a program error in the Driving Support ECU, if the radar sensor is inactive for 10 seconds or more, the PCS may not reactivate Pre-Collision Braking on certain 2011-2014 Model Year Sienna vehicles equipped with PCS.

the brake pedal while lightly applying the brake pedal. New front brake pads and a new field fix repair procedure have been developed to improve this condition.

the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.

equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.

ANY PREVIOUS PRINTED VERSIONS OF THIS BULLETIN SHOULD BE DISCARDED. SOME 2011 2016 MODEL YEAR SIENNA VEHICLES MAY EXHIBIT A VIBRATION/PULSATION FROM THE FRONT BRAKES THAT CAN BE FELT IN THE BRAKE PEDAL WHILE LIGHTLY APPLYING THE BRAKE PEDAL. NEW FRONT BRAKE PADS AND A NEW FIELD FIX REPAIR PROCEDURE HAVE BEEN DEVELOPED TO IMPROVE THIS CONDITION. "

A PROGRAM ERROR, IN DRIVING SUPPORT ECU, HAS RADAR SENSOR PRE-COLLISION SYSTEM (PCS) INACTIVE 10 SECONDS OR MORE, WHILE STOPPED, WILL FAIL TO REACTIVATE PRE-COLLISION BRAKING. MODEL 2011-2014 SIENNA. *PE

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced

? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

be involved.

be involved.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.

There a re man benefits of this oil.

Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.

There are multiple benefits of this oil including: Reduced friction and wear on engine surfaces, Improved fuel economy, Reduction in waste oil stream (in vehicles approved for 10,000 mile oil change intervals), Reduced maintenance cost (in vehicles approved for 10,000 mile oil change intervals). Due to the improved performance and durability of 0w20 synthetic oil, Toyota has extended the oil change intervals to 10,000 mile for most vehicles that require this oil. With this change, the following should be noted: The 2TR-FE (4Runner/Tacoma) and the 3UR-FBE (Flex Fuel Tundra/Sequoia) are the exceptions to this new change interval program; these engines have not been approved for the 10,000 mile interval at this time. A 5,000 mile oil change interval is still required for these vehicles. Also, the Flex Fuel 3UR-FBE requires a 2,500 mile interval when operated on E85 50% of the time or more. Only Toyota vehicles in which 0w20 oil is mandatory (except for the 2TR-FE & 3UR-FBE Engines) have been approved for extended oil change intervals. Vehicles in which 0w-20 is an option to 5w20 (or 5w30) will continue to require 5,000 mile change intervals, even if 0w20 oil is used. In case of vehicles with 10,000 mile oil change intervals, the 5,000 mile service interval has not been eliminated. The traditional 5,000 mile maintenance procedures (such as tire rotation) will continue to be required, and the fluid levels (including engine oil) will need to be checked and adjusted at this time. If the vehicle operation meets the standard criteria for "Special Operating Conditions" such as: driving off-road, on dirt roads, towing a trailer, making repeated short trips under 32 degrees F, or extensive idling, the engine oil must be replaced at 5,000 mile intervals, regardless of oil used.

There are multiple benefits of this oil. Due to the improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicle that require this oil.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.

There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

*Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY."

(ATF) level at normal vehicle operating temperature. Note: The following adjustment procedures are for U660E/F and U760E/F transmissions.

from the original transaxle case and install it into the reman unit. A NEW O-ring and printed installation instructions are supplied in separate bag with the reman unit. An instruction tag is also affixed to the unit.

transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly

(ATF) level at normal vehicle operating temperature.

automatic transmissions.

assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.

remanufactured automatic transmissions.

converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.

mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.

model year Toyota vehicles.

model year Toyota vehicles.

Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

This allows for more amperage to draw the Powerkneel up allowing the up-limit switch to be tripped consistently. If the up limit switch is not engaged, a vehicle may not come out of park or the conversion may not operate properly next time it is deployed

This allows for more amperage to draw the Powerkneel up allowing the up-limit switch to be tripped consistently. If the up limit switch is not engaged, a vehicle may not come out of park or the conversion may not operate properly next time it is deployed

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Flat towing or towing where only the front or rear wheels are supported may damage the all-wheel drive system.

significantly colder or warmer than shop temperature. Seasonal temperature change can dramatically alter tire pressure, which can cause the low tire pressure warning light to illuminate.

The subject vehicles are equipped with Safety Connect, which allows drivers to contact the Toyota 24/7 response center at the touch of a button. Toyota has identified that the Safety Connect System in the subject vehicles has become disabled due to an unplanned expiration of the Mobile Identification Number/Mobile Directory Number.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

Technical Instructions for Limited Service Campaign E0K. Safety Connect System Disabled. Certain 2014 Model Year Avalon, Avalon Hybrid , Highlander, and Sienna vehicles.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

DUE TO AN UNPLANNED EXPIRATION OF MOBILE IDENTIFICATION NUMBER/MOBILE DIRECTORY NUMBER, IN SOME VEHICLES, THE SAFETY CONNECT SYSTEM HAS BECOME DISABLED AND NEEDS REPROGRAMMING. *PE

reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pretensioner devices did not perform as expected, please follow the steps in the recommendations section below.

occupant easily enter and exit the vehicle. To ensure that the Auto Access Seat system is operating properly, inspect the Auto Access Seat functions during Pre-Delivery Service (PDS).

Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.

seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.