2007 Toyota Sienna TSBs

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.

source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.

quenching process during manufacturing.

as a Result of Heat or Humidity.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003 - 2005 model year 4Runner, 2005 - 2010 model year Avalon, 2007 - 2011 model year Camry and Camry Hybrid, 2004 -2010 model year Sienna, and 2004 - 2008 model year Solara vehicles. In Mid-December, 2014 Toyota announced the reimbursement Phase of this Program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota will be launching the part replacement portion of this Program is several phases; please refer to the table below for part replacement model phasing.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003 - 2005 model year 4Runner, 2005 - 2010 model year Avalon, 2007 - 2011 model year Camry and Camry Hybrid, 2004 - 2010 model year Sienna, and 2004 - 2008 model year Solara vehicles.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003 - 2005 model year 4Runner, 2005 - 2010 model year Avalon, 2007 - 2011 model year Camry and Camry Hybrid, 2004 - 2010 model year Sienna, and 2004 - 2008 model year Solara vehicles. In Mid-December, 2014 Toyota announced the reimbursement Phase of this Program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota will be launching the part replacement portion of this Program is several phases; please refer to the table below for part replacement model phasing.

This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003 - 2005 model year 4Runner, 2005 - 2010 model year Avalon, 2007 - 2011 model year Camry and Camry Hybrid, 2004 - 2010 model year Sienna, and 2004 - 2008 model year Solara vehicles.

THIS PROGRAM EXTENDS THE WARRANTY COVERAGE FOR REPAIRS RELATED TO CRACKED AND/OR STICKY/MELTING DASHBOARDS (INSTRUMENT PANELS) AS A RESULT OF HEAT OR HUMIDITY ON 2003-2005 MODEL YEAR 4RUNNER, 2005-2010 MODEL YEAR AVALON, 2007-2011 MODEL YEAR CAMRY AND CAMRY HYBRID, 2004-2010 MODEL YEAR SIENNA, AND 2004-2008 MODEL YEAR SOLARA VEHICLES.

INSPECT THE SLIDING DOOR LOCK ASSEMBLIES AND REPLACE THE AFFECTED COMPONENTS AS NEEDED, ACCORDING TO THE LISTED INSTRUCTIONS. *PE

*PE

*NJ

*NJ

Please see T-SB-0057-18.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0044-16.

Please see T-SB-0063-20.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0010-20.

Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing.

Please see T-SB-0012-13.

satisfaction.

correct pulling complaints.

Please see T-SB-0304-17.

Please see T-SB-0134-16.

Once the system is reset, all previously registered keys will be erased.

Once the system is reset, all previously registered keys will be erased.

parental passcode for the system.

Please see T-SB-0054-13.

parental passcode for the system.

Please see T-SB-0185-13.

Please see T-SB-0030-14 .

heat or humidity.

heat or humidity.

SINCE PRIOR TO THAT ANNOUNCEMENT, TOYOTA HAS BEEN DILIGENTLY MAKING PARTS PREPARATIONS FOR THE PARTS REPLACEMENT PHASE OF THIS PROGRAM. DUE TO THE AGE, VOLUME, AND BREADTH OF THE COVERED VEHICLES SUBJECT TO THE PROGRAM AND THE SIZE AND COMPLEXITY OF DASHBOARD MANUFACTURING, TOYOTA HAS LAUNCHED THE PART REPLACEMENT PORTION OF THIS PROGRAM IN SEVERAL PHASES; PLEASE REFER TO THE TABLE BELOW FOR PART REPLACEMENT MODEL PHASING.

THE POWER REAR HATCH WILL NOT CLOSE COMPLETELY. THE HATCH WILL START TO CLOSE AND THEN WILL REVERSE BACK UP TO THE OPEN POSITION. *RM

Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.

In Mid-December, 2014, Toyota announced the reimbursement Phase of this warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing.

dashboards as a result of heat or humidity. In Mid-December, 2014, Toyota announced the reimbursement Phase of this voluntary warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases.

Please see T-SB-0304-17.

Please see T-SB-0304-17.

All dealership technicians performing this repair are required to successfully complete the most current version of the E-Learning course ?Safety Recall and Service Campaign Essentials.? To ensure that all vehicles have the repair performed correctly, technicians performing this repair are required to currently hold at least one of the following certification levels: ? Toyota Certified (any classification) ? Toyota Expert (any classification) ? Master Technician ? Master Diagnostic Technician

In Mid-December, 2014 Toyota announced the reimbursement Phase of this warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota will be launching the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing. Although Toyota is increasing production levels, it is difficult to predict customer demand and where parts need to be shipped to support customer demand. It is important that dealerships explain to customers that there still may be a period of time the customer will need to wait before part replacement can be performed. Please be sure to take this into consideration when performing customer scheduling.

Please note the following information for Regional and PD associates.

Please note the following information for Regional and PD associates.

Please note the following information for Regional and PD associates.

performance.

campaign repairs completed.

campaign repairs completed.

cracked and/or sticky/melting dashboards as a result of heat or humidity.

Special Service Campaign A7E after being inspected and/or repaired.

Please note the following information for Regional and PD associates.

PLEASE NOTE THE FOLLOWING INFORMATION FOR REGIONAL AND PD ASSOCIATES.

IN MID-DECEMBER, 2014 TOYOTA ANNOUNCED THE REIMBURSEMENT PHASE OF THIS WARRANTY ENHANCEMENT PROGRAM. SINCE PRIOR TO THAT ANNOUNCEMENT, TOYOTA HAS BEEN DILIGENTLY MAKING PARTS PREPARATIONS FOR THE PARTS REPLACEMENT PHASE OF THIS PROGRAM. DUE TO THE AGE, VOLUME, AND BREADTH OF THE COVERED VEHICLES SUBJECT TO THE PROGRAM AND THE SIZE AND COMPLEXITY OF DASHBOARD MANUFACTURING, TOYOTA WILL BE LAUNCHING THE PART REPLACEMENT PORTION OF THIS PROGRAM IN SEVERAL PHASES; PLEASE REFER TO THE TABLE BELOW FOR PART REPLACEMENT MODEL PHASING. ALTHOUGH TOYOTA IS INCREASING PRODUCTION LEVELS, IT IS DIFFICULT TO PREDICT CUSTOMER DEMAND AND WHERE PARTS NEED TO BE SHIPPED TO SUPPORT CUSTOMER DEMAND. IT IS IMPORTANT THAT DEALERSHIPS EXPLAIN TO CUSTOMERS THAT THERE STILL MAY BE A PERIOD OF TIME THE CUSTOMER WILL NEED TO WAIT BEFORE PART REPLACEMENT CAN BE PERFORMED. PLEASE BE SURE TO TAKE THIS INTO CONSIDERATION WHEN PERFORMING CUSTOMER SCHEDULING."

IN MID-DECEMBER, 2014, TOYOTA ANNOUNCED THE REIMBURSEMENT PHASE OF THIS WARRANTY ENHANCEMENT PROGRAM. SINCE PRIOR TO THAT ANNOUNCEMENT, TOYOTA HAS BEEN DILIGENTLY MAKING PARTS PREPARATIONS FOR THE PARTS REPLACEMENT PHASE OF THIS PROGRAM. DUE TO THE AGE, VOLUME, AND BREADTH OF THE COVERED VEHICLES SUBJECT TO THE PROGRAM AND THE SIZE AND COMPLEXITY OF DASHBOARD MANUFACTURING, TOYOTA HAS LAUNCHED THE PART REPLACEMENT PORTION OF THIS PROGRAM IN SEVERAL PHASES; PLEASE REFER TO THE TABLE BELOW FOR PART REPLACEMENT MODEL PHASING."

AVAILABLE FOR 05-08 MODEL YEAR SIENNA VEHICLES. *PE

*PE

T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.

An updated repair procedure is available to address this condition. Follow the procedures in this bulletin to repair the floor harness and the side airbag squib circuit.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

In some instances a P2195 or P2197 (A/F Sensor Signal Stuck Lean) DTC may also be present. This condition may be caused by incorrect Air Fuel Ratio Sensor response. Additionally, a P0606 (ECM/PCM Processor) DTC may be present due to incorrect Oxygen Sensor operation. The following repair procedures should be used to properly diagnose and repair this condition.

The connector could have been improperly crimped during the manufacturing process. In certain cases, oxidization buildup in the connector can occur resulting in illumination of the airbag warning lamp.

An updated repair procedure is available to address this condition. Follow the procedures in this bulletin to repair the floor harness and the side airbag squib circuit.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION."

THERE IS AN EXCESSIVE ELECTRICAL RESISTANCE, ON SOME VEHICLES, WHERE THE CONNECTOR HAD BEEN IMPROPERLY CRIMPED, DURING TIME OF MANUFACTURING, AND OXIDIZATION BUILDUP, IN CONNECTOR, RESULT IN AN ILLUMINATION OF AIRBAG WARNING LAMP. SEE TSB-0069-12 REV 2. MODEL 2004-2009 SIENNA. *PE

INCORRECT OXYGEN SENSOR OPERATION MAY BE PRESENT, DUE TO ECM/PCM PROCESSOR P0606 DTC. *PE

*PE

REPLACE/REPAIR SIDE AIRBAG SQUIB CIRCUIT, DEPENDING ON PRODUCTION DATE. *PE MODEL 2005-09 SIENNA. UPDATED 4/15/13. *PE SEE TC-14-001. UPDATED 4/25/14. *PE

FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. MODEL YEARS FROM 2001-2011. *PE

*NJ UPDATED 5/1/08. *NJ

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

been disconnected or power to the Engine ECM has been interrupted.

power to the Engine ECM has been interrupted.

If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.

Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.

Enhancement Program to extend the warranty coverage for repairs related a leaking or seeping Engine Oil Cooler Pipe. In these vehicles, Toyota has received some reports where vehicles can experience an oil leak or seep from the Engine Oil Cooler Pipe. Although the Engine Oil Cooler Pipe is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs related a leaking or seeping Engine Oil Cooler Pipe. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Enhancement Program to extend the warranty coverage for repairs related a leaking or seeping Engine Oil Cooler Pipe. In these vehicles, Toyota has received some reports where vehicles can experience an oil leak or seep from the Engine Oil Cooler Pipe. Although the Engine Oil Cooler Pipe is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs related a leaking or seeping Engine Oil Cooler Pipe. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

? The Production Change Information section has been removed. ? The Parts Information and Repair Procedure sections have been updated. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. EL004-04. ? Applicability has been updated to include 2005 ? 2010 model year Sienna vehicles. Some 2004 ? 2010 model year Sienna vehicles may exhibit a condition where the power function of the sliding door is inoperative. A new service part has been developed so that the replacement of the entire motor/cable assembly is not required.

been disconnected or power to the Engine ECM has been interrupted.

VVT-i actuator may degrade over time. This condition may cause oil to leak from the VVT-i oil hose producing abnormal engine noise and the oil pressure light to illuminate. The following vital information is provided to inform you and your staff of the owner notification timing and your degree of involvement.

VVT-i actuator may degrade over time. This condition may cause oil to leak from the VVT-i oil hose producing abnormal engine noise and the oil pressure light to illuminate.

cooler pipes.

POWER TO THE ENGINE ECM HAS BEEN INTERRUPTED.

ON CERTAIN VEHICLES THE RUBBER OIL SUPPLY HOSE, FOR VVT-I ACTUATOR, IS DEGRADING OVER TIME AND CAUSING A LEAKAGE OF OIL, FROM OIL HOSE, PRODUCING AN ILLUMINATION OF OIL PRESSURE LIGHT AND AN ABNORMAL ENGINE NOISE. MODEL 2005-09 AVALON, 2008 HIGHLANDER, 2006-09 RAV4, 2007-10 CAMRY, 2007-10 SIENNA. *PE

AN ENHANCEMENT WARRANTY PROGRAM, ON CERTAIN VEHICLES, HAS BEEN ANNOUNCED TO PROVIDE WARRANTY COVERAGE FOR REPAIRS RELATING TO LEAKAGE OR SEEPAGE ENGINE OIL COOLER PIPE. MODEL 2007-11 SIENNA, 2008-11 HIGHLANDER, 2009-11 VENZA, 2011 HIGHLANDER HYBRID. *PE

*PE

INFORMATION HAS BEEN PROVIDED REGARDING THIS ISSUE. *PE

ON CERTAIN VEHICLES EQUIPPED WITH A 2GR-FE (V6) ENGINE, THE RUBBER PORTION OF THE OIL SUPPLY HOSE FOR THE VVT-I ACTUATOR MAY DEGRADE OVER TIME. THIS CONDITION MAY CAUSE OIL TO LEAK FROM THE VVT-I OIL HOSE PRODUCING ABNORMAL ENGINE NOISE AND THE OIL PRESSURE LIGHT TO ILLUMINATE. CSC LETTER WAS REC'D. *PE

WHICH MAY BE ACCOMPANIED BY A MIL ON AND ONE OR MORE VVT-I RELATED DIAGNOSTIC TROUBLE CODES (DTCS). *PE

THE ENGINE CONTROL MODULE OR ECM (SAE TERM: POWERTRAIN CONTROL MODULE/PCM). *PE

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

Follow the procedure in this bulletin to address this condition.

equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.

inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.

becomes cracked and/or has a shiny/degraded appearance. The pad surface may also become sticky or adherent. Follow the procedure in this bulletin to address this condition.

becomes cracked and/or has a shiny/degraded appearance. The pad surface may also become sticky or adherent. Follow the procedure in this bulletin to address this condition.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.

commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.

commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.

obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.

integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.

INTEGRAL PART OF OUR COMMITMENT TO MEET CUSTOMER EXPECTATIONS OF TOYOTA PRODUCTS. TOYOTA WILL BE SENDING SAFETY RECALL FOLLOW-UP NOTICES TO REMIND OWNERS WHOSE VEHICLES HAVE NOT YET HAD CAMPAIGN REPAIRS COMPLETED. WE REQUEST YOUR ASSISTANCE IN COMPLETING THE APPLICABLE CAMPAIGN REPAIRS AS OWNERS RECEIVE THE FOLLOW-UP NOTICE AND CONTACT YOUR DEALERSHIP. PLEASE NOTE THE FOLLOW-UP ACTIVITY MAY CAUSE AN INCREASE IN YOUR CURRENT CAMPAIGN OWNER APPOINTMENTS. TOYOTA WILL CONTINUE WITH ADDITIONAL FOLLOW-UP ACTIVITIES IN THE MONTHS TO COME. PLEASE TAKE THIS INTO CONSIDERATION WHEN ANALYZING YOUR MANPOWER REQUIREMENTS."

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

serviceability and reduce ownership cost. This repair procedure only applies to vehicles where the steering rack leak is originating from the right (passenger) side and is the OEM steering rack assembly.

*Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY."

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced

cable corrosion even after being inspected and/or repaired as part of a previous Special Service Campaign. During normal usage, water splashing rearward can reach the spare tire carrier due to variation in the placement of the foam splash guard or loss of the splash guard. If the splashed water contains high concentrations of road salt, corrosion of the spare tire carrier and the carrier cable may result. In limited instances, the spare tire may become seperated from the spare tire carrier and create a road hazard that could cause a vehicle crash. Toyota has revised the inspection and remedy procedures for this special service campaign. All owners of affected vehicles in Warm Climate States are now eligible for an inspection of the spare tire carrier assembly and cable.

cable corrosion even after being inspected and/or repaired as part of a previous Special Service Campaign. During normal usage, water splashing rearward can reach the spare tire carrier due to variation in the placement of the foam splash guard or loss of the splash guard. If the splashed water contains high concentrations of road salt, corrosion of the spare tire carrier and the carrier cable may result. In limited instances, the spare tire may become seperated from the spare tire carrier and create a road hazard that could cause a vehicle crash. Toyota has revised the inspection and remedy procedures for this special service campaign. All owners of affected vehicles in Warm Climate States are now eligible for an inspection of the spare tire carrier assembly and cable.

? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

be involved.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

*RM

customer?s iPhone is operating on iOS9 firmware The customer?s iPhone is connected to the vehicle via Bluetooth. If the vehicle is equipped with a Fujitsu-Ten brand head unit, the customer may complain of one or more of the following: When playing media via Bluetooth audio and pressing the ?Pause? button on the phone, media playback pauses for one second before resuming playback. Yelp searches return an error when search criteria includes a special character, e.g. !,$,#. If the vehicle is equipped with a Pioneer brand head unit, the customer may complain of one or more of the following: The customer?s iPhone does not support the album image feature. When playing media via Bluetooth audio, one or more of a number of play/pause issues occur.

The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.

customer?s iPhone is operating on iOS9 firmware The customer?s iPhone is connected to the vehicle via Bluetooth. If the vehicle is equipped with a Fujitsu-Ten brand head unit, the customer may complain of one or more of the following: When playing media via Bluetooth audio and pressing the ?Pause? button on the phone, media playback pauses for one second before resuming playback. Yelp searches return an error when search criteria includes a special character, e.g. !,$,#. If the vehicle is equipped with a Pioneer brand head unit, the customer may complain of one or more of the following: The customer?s iPhone does not support the album image feature. When playing media via Bluetooth audio, one or more of a number of play/pause issues occur.

to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

THE CUSTOMER'S IPHONE IS CONNECTED TO THE VEHICLE VIA BLUETOOTH. THE CUSTOMER MAY COMPLAIN OF THE FOLLOWING ISSUES: WHEN RECEIVING TWO INCOMING CALLS SIMULTANEOUSLY, BOTH CALLS ARE ENDED AUTOMATICALLY. ITUNES RADIO APP DOES NOT PLAY VIA BLUETOOTH AUDIO. PODCAST AND AUDIOBOOK MEDIA PLAYBACK IS INOPERATIVE VIA BLUETOOTH AUDIO.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

SOME CUSTOMERS MAY EXPERIENCE THAT THE SPARE TIRE IS DIFFICULT TO REMOVE OR THE CABLE IS BINDING. *JS

IN COLD WEATHER WHERE SALT IS USED, THE SALT CAN CORRODE THE SPARE TIRE CARRIER CABLE. 1998-2020 SIENNA. *RM

transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly

automatic transmissions.

assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.

remanufactured automatic transmissions.

converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.

mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.

INOPERATIVE AFTER VEHICLE HAS COLD SOAKED IN SUBFREEZING AMBIENT AIR TEMPERATURES. *PE UPDATED 9/23/09. *PE

reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pretensioner devices did not perform as expected, please follow the steps in the recommendations section below.

Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.

Program to extend the warranty coverage for the Side Airbag Connector on certain 2004 to 2009 Model Year Toyota Sienna vehicles.

seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.

*PE

SOME MODEL VEHICLES MAY EXHIBIT AN SRS LAMP ON CONDTION WITH DIAGNOSTIC TROUBLE CODE (DTC) B0111 AND/OR B0116. AN UPDATED REPAIR PROCEDURE IS AVAILABLE TO ADDRESS THIS CONDITION. *PE

Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

sticky/melting dashboards as a result of heat or humidity.

MODELS 2003-05 4RUNNER, 2005-10 AVALON, 2007-11 CAMRY & HYBRID, 2004-10 SIENNA, 2004-08 SOLARA. *PE

*KB