2018 Toyota Sequoia TSBs

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

binding, seizing, or sticking condition when attempting to open or close. In some cases, a clicking noise is present when the sliding sunroof or moonroof is stuck open or closed. This condition may be caused by rusted or seized sliding roof cables

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

binding, seizing, or sticking condition when attempting to open or close. In some cases, a clicking noise is present when the sliding sunroof or moonroof is stuck open or closed. This condition may be caused by rusted or seized sliding roof cables. Follow the Repair Procedure in this bulletin to address this condition.

T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

This noise may be due to a fracture/crack in the plastic over mold of the door check arm by the pivot area. Follow the Repair Procedure in this bulletin to address this condition. NOTE If the vehicle is being repaired due to damage from an accident, this Service Bulletin and the part numbers listed do NOT apply.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

CARPET FLOOR MATS CERTAIN 2012-2019 Sequoia

Please see T-SB-0304-17.

Please see T-SB-0304-17.

vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected using the following procedure during Pre-Delivery Service (PDS).

? Because the remedy for J0H addresses both the H0Y condition and the J0H condition, all vehicles involved in Special Service Campaign H0Y (whether H0Y was completed or not) are now included in Safety (Noncompliance) Recall J0H. ? All vehicles involved in the H0Y Special Service Campaign are also involved in the Safety (Noncompliance) Recall J0H. ? All vehicles with H0Y incomplete as of February 20, 2018 have been marked expired in TIS. ? This document should only be used for claim processing information for vehicles that had the H0Y remedy performed on February 20, 2018 or earlier.

Toyota Genuine carpet floor mat set that is designed for different model year Sequoia vehicles (model years 2008-2011). If installed, the driver?s floor mat would not be secured in the way it was designed due to differences in the attachment grommets

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled.

appropriate tool to use for diagnosis

A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ?Circuit demand is too high for GFCI rating ?Worn out GFCI internal contacts ?Improper installation or wiring of GFCI breaker

angle before performing axis beam adjustment. When used in conjunction with the repair manual, these BSM tips leverage SSTs and readily available tools to support sensor angle confirmation in varying shop environments.

carpet floor mat set that is designed for different model year Sequoia vehicles (model years 2008-2011). If installed, the driver?s floor mat would not be secured in the way it was designed due to differences in the attachment grommets.

floor mat set that is designed for different model year Sequoia vehicles (model years 2008-2011). If installed, the driver?s floor mat would not be secured in the way it was designed due to differences in the attachment grommets.

mat set that is designed for different model year Sequoia vehicles (model years 2008-2011). If installed, the driver?s floor mat would not be secured in the way it was designed due to differences in the attachment grommets.

mat set that is designed for different model year Sequoia vehicles (model years 2008-2011). If installed, the driver?s floor mat would not be secured in the way it was designed due to differences in the attachment grommets.

that is designed for different model year Sequoia vehicles (model years 2008-2011). If installed, the driver?s floor mat would not be secured in the way it was designed due to differences in the attachment grommets.

A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ? Circuit demand is too high for GFCI rating ? Worn out GFCI internal contacts ? Improper installation or wiring of GFCI breaker

Below is an explanation of what information is required when testing a 12V battery on the new Warranty Battery Testers.

angle before performing axis beam adjustment. When used in conjunction with the repair manual, these BSM tips leverage SSTs and readily available tools to support sensor angle confirmation in varying shop environments.

T-SB-0103-16 and T-SB-0337-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 and T-SB-0337-17 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2016 ? 2018 model year vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (version 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled

T-SB-0103-16 and T-SB-0337-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0103-16 and T-SB-0337-17 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2016 ? 2018 model year vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (version 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled

The EDR only collects, stores, and allows retrieval of vehicle event data, including crash events. It does not control the operation of the vehicle or crash safety systems. Due to a software error in the air bag ECU where EDR data is stored, the EDR data for ?Frontal Airbag Deployment, Time to 1st Stage Deployment,? and ?Frontal Airbag Deployment Time to 2nd Stage Deployment,? will show the same value at the time an event is recorded. This software error has no effect on the actual air bag?s deployment times for both stages. Both air bags operate as designed.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

The EDR only collects, stores, and allows retrieval of vehicle event data, including crash events. It does not control the operation of the vehicle or crash safety systems. Due to a software error in the air bag ECU where EDR data is stored, the EDR data for ?Frontal Airbag Deployment, Time to 1st Stage Deployment,? and ?Frontal Airbag Deployment Time to 2nd Stage Deployment,? will show the same value at the time an event is recorded. This software error has no effect on the actual air bag?s deployment times for both stages. Both air bags operate as designed.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

Customer feedback indicates the following areas deserve special attention when performing PDS: ? Careful inspection for paint chips/scratches and body dents/dings. ? Proper operation of electrical accessories (including interior light, clock, and radio reset). ? Interior cleanliness. ? Proper function of mechanical systems. A new PDS Check Sheet has been developed for the 2018 model year Sequoia. Some check points have been added, expanded, or clarified.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate Installation Procedure to attach the driver?s side, and if applicable the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharges and/or failed batteries due to lack of maintenance. It is the dealer's responsibility to maintain the specific State-Of-Charge (SOC) of the vehicle's battery while in stock and assure proper SOC at delivery.

Center Air Bag Sensor Assembly Software Update. Certain 2018 Sequoia and 2018 Tundra

The EDR only collects, stores, and allows retrieval of vehicle event data, including crash events. It does not control the operation of the vehicle or crash safety systems. Due to a software error in the air bag ECU where EDR data is stored, the EDR data for ?Frontal Airbag Deployment, Time to 1st Stage Deployment,? and ?Frontal Airbag Deployment Time to 2nd Stage Deployment,? will show the same value at the time an event is recorded. This software error has no effect on the actual air bag?s deployment times for both stages. Both air bags operate as designed.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

The settlement includes Toyota?s agreement to provide a Customer Support Program for certain 2015-2020 model year (MY) vehicles that were not previously involved in a Safety Recall or Special Service Campaign related to the low pressure fuel pump. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

The settlement includes Toyota?s agreement to provide a Customer Support Program for certain 2014-2020 model year (MY) vehicles originally equipped with low pressure fuel pumps repaired under Safety Recall 20TA02, Safety Recall 21TA03, Safety Recall 21TA05 or Special Service Campaign 21TC03. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

following Diagnostic Trouble Codes (DTCs): ?DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ?DTC P0087 Fuel Rail / System Pressure ? Too Low Techstream data list analysis may reveal positive fuel trims including a no pressure condition verified by a manual fuel pressure gauge. Follow the Repair Procedure in this bulletin to address these conditions.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle's system and components. Any problems that are found should be corrected immediately.

These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0045-22

Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.

Please see T-SB-0012-21.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0003-20.

repair manual target to the proper size.

Please see T-SB-0279-17.

Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.

Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.

Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.

Reviside to include Additional Models and Years.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible.

Pre-Collision System (PCS), also known as Automatic Emergency Braking (AEB) as part of Toyota Safety Sense. The Pre-Collision System (PCS) defaults its operating mode to ON after each ignition (IG) cycle. In some driving conditions, such as extended off-road use, driving with tire chains in adverse conditions, towing another vehicle, or when your vehicle is being towed, drivers should operate the vehicle with PCS OFF. Drivers may also prefer to maintain this setting after each IG cycle. If this functionality is requested, follow the procedure in this Service Bulletin to disable the PCS mode reset after each IG cycle.

Brake vibration can occur at any time if improper torque is applied to lug nuts. Even one lug nut over or under torqued can cause vibration.

The following software update modifies the system functionality while the vehicle is in motion, improving customer experience. New software is available to address the following: ? Phone keypad unlocked while vehicle is in motion ? Contact list unlocked while vehicle is in motion ? Bluetooth connected phone switching while vehicle is in motion ? Navigation transition improvements (if equipped) ? Revised BT-Audio help pop-up ? Call history list call function improvements ? Reboot after coming out of Reverse ? Errors during phonebook transfer ? Sound settings reset after ignition key cycle ? Surround turns back on after key cycle ?Abnormal operation when listening to FM HD Radio

This is caused by the phone Hands Free volume being too low.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

In some instances, this condition causes the Panasonic head unit to reboot when the Bluetooth connection is initiated.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

during the head unit software installation process

In some instances, this condition causes the Panasonic head unit to reboot when the Bluetooth connection is initiated.

Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for echo or excessive background noise.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

memory.

This is caused by the phone Hands Free volume being too low. These settings may need to be reapplied any time the phone is paired to a new head unit, a phone update is applied, or the phone is un-paired and re-paired.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

repeated depressing of the brake pedal or shortly after the vehicle begins to move.

SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0058-13.Service Bulletin No. T-SB-0058-13 is obsolete and any printed versions should be discarded. Some 2009 ? 2018 model year Sequoia and 2009 ? 2019 model year Tundra vehicles equipped with a 3UR-FBE engine may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs): ? DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ? DTC P0172 and/or P0175 (System Too Rich Bank 1/Bank 2) ? DTC P1604 (Startability Malfunction) Techstream data list analysis may reveal negative fuel trims and an elevated alcohol density estimate relative to the vehicle?s actual fuel alcohol content. Follow the Repair Procedure in this bulletin to address these conditions.

T-SB-0058-13. Service Bulletin No. T-SB-0058-13 is obsolete and any printed versions should be discarded. Some 2009 ? 2018 model year Sequoia and 2009 ? 2019 model year Tundra vehicles equipped with a 3UR-FBE engine may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs). ? DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ? DTC P0172 and/or P0175 (System Too Rich Bank 1/Bank 2) ? DTC P1604 (Startability Malfunction) Techstream Data List analysis may reveal negative fuel trims and an elevated alcohol density estimate relative to the vehicle?s actual fuel alcohol content. Follow the Repair Procedure in this bulletin to address this condition.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

repeated depressing of the brake pedal or shortly after the vehicle begins to move.

5. TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN K0A ENGINE ECU SOFTWARE UPDATE CERTAIN: 2018 TUNDRA 2018 SEQUOIA (Reference the separate Technical Instructions for 2018 Camry and Sienna)

Under a specific condition, this software may not detect a malfunctioning sensor due to an error in the software. As a result, affected vehicles do not meet certain onboard diagnostic (OBD) regulations.

warning message in the combination meter immediately after engine startup and an inoperative BSM system with Diagnostic Trouble Codes (DTCs) C1AB4 (Open in Outer Mirror Indicator [Master]) or C1AB5 (Open in Outer Mirror Indicator [Slave]). Follow the Repair Procedure in this bulletin to address this condition.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

Adding stop leak products to the A/C system is not a recommended or approved Toyota repair process. During A/C service, moisture enters the A/C system, and can react with the previously added A/C stop leak, forming a gelatinous substance. The gel substance that forms can cause the A/C compressor to bind and or seize.

year Tundra vehicles are equipped with Pre-collision System (PCS) and Dynamic Radar Cruise Control (DRCC) as part of the Toyota Safety Sense (TSS) package. The PCS and DRCC systems are designed to help mitigate a potential collision and maintain a pre-determined traveling distance. It is recommended to disable the PCS and DRCC systems on vehicles that have been modified (ride height, oversized wheels/tires, brush bars, etc.) in a way that potentially disrupts the functionality of these systems. Vehicle owner?s written consent is required before performing the calibration to permanently disable the PCS and DRCC systems. Follow the Repair Procedure in this bulletin to disable the PCS and DRCC systems.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Pre-collision System (PCS) and Dynamic Radar Cruise Control (DRCC) as part of the Toyota Safety Sense (TSS) package. The PCS and DRCC systems are designed to help mitigate a potential collision and maintain a pre-determined traveling distance. It is recommended to disable the PCS and DRCC systems on vehicles that have been modified (ride height, oversized wheels/tires, brush bars, etc.) in a way that potentially disrupts the functionality of these systems. Vehicle owner?s written consent is required before performing the calibration to permanently disable the PCS and DRCC systems. Follow the Repair Procedure in this bulletin to disable the PCS and DRCC systems.

Pre-collision System (PCS) and Dynamic Radar Cruise Control (DRCC) as part of the Toyota Safety Sense (TSS) package. The PCS and DRCC systems are designed to help mitigate a potential collision and maintain a pre-determined traveling distance. It is recommended to disable the PCS and DRCC systems on vehicles that have been modified (ride height, oversized wheels/tires, brush bars, etc.) in a way that potentially disrupts the functionality of these systems. Vehicle owner?s written consent is required before performing the calibration to permanently disable the PCS and DRCC systems. Follow the Repair Procedure in this bulletin to disable the PCS and DRCC systems.

equipped with Pre-collision System (PCS) and Dynamic Radar Cruise Control (DRCC) as part of the Toyota Safety Sense (TSS) package. The PCS and DRCC systems are designed to help mitigate a potential collision and maintain a pre-determined traveling distance. It is recommended to disable the PCS and DRCC systems on vehicles that have been modified (ride height, oversized wheels/tires, brush bars, etc.) in a way that potentially disrupts the functionality of these systems. Vehicle owner?s written consent is required before performing the calibration to permanently disable the PCS and DRCC systems. Follow the Repair Procedure in this bulletin to disable the PCS and DRCC systems.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

If the wheels are replaced or refinished before vehicle delivery, it is important the tires remain on the vehicle in the same location and in the same direction of rotation. Refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

model year Toyota vehicles.

model year Toyota vehicles.

model year Toyota vehicles.

The procedure recommended below can be used to confirm the beam axis has been updated when performing the Blind Spot Monitor Beam Axis Confirmation.

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match the radio station that is playing.?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi/km?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010145), Entune? Audio Plus (version 010161), Entune? Premium Audio (version 010189), or earlier may exhibit one of the following conditions: ?Map will not display after it has been reprogrammed from the map micro SD card. Updated system software is now

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match the radio station that is playing.?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi/km?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010145), Entune? Audio Plus (version 010161), Entune? Premium Audio (version 010189), or earlier may exhibit one of the following conditions: ?Map will not display after it has been reprogrammed from the map micro SD card. Updated system software is now avail

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match radio station that is playing. ?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Updated system software is now available to address these conditions. Follow the Software Update Procedure in this bulletin to install the latest software version.

010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match radio station that is playing. ?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative.

T-SB-0279-17. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0279-17 is obsolete and ANY printed versions should be discarded. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ? Head unit reboots at a specific location ? Abnormal Destination Search app operation ? Rebooting caused by no songs on the USB-connected iPhone ? A one-time reboot after ignition is cycled to ACC-ON ? Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ? Head unit reboots intermittently ? Half blank screen appears when on the maintenance screen and shifting to Reverse ? Screen freezes during an incoming phone call ? Incorrect time displays on the diagnostic menu ? Radio station information does not match radio station that is playing ? Abnormal playlist browsing operation ? Mute stays enabled after key cycle ? ?Search along my route? is inoperative ? Traffic data scales improperly ? Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi?) ? MID compass does not match navigation screen when switching to North up ? Navigation does not match MID when switching from miles to kilometers ? Speed limit is blank on navigation screen ? Go button on VR screen is inoperative

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.

Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.