2022 Toyota RAV4 TSBs

steam that can cause an incorrect engine sensor reading. This can lead to a warning light, a rough-running engine, or a potential engine stall while idling or operating at low speeds.

steam that can cause an incorrect engine sensor reading. This can lead to a warning light, a rough-running engine, or a potential engine stall while idling or operating at low speeds.

Upon further inspection, a loose C90/C27 connector pin at the EGR valve may be found. To correct this concern, please reference the repair section of this TSB.

Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing extended coverage under this Customer Support Program for repairs related to excessive corrosion to the wire harness connections at the Rear Motor Generator. Excessive corrosion can cause AM Radio Static during certain drive cycles, or the vehicle may not start.

and 2019 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F 41F: P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold P030000 Random/Multiple Cylinder Misfire Detected P030100 Cylinder 1 Misfire Detected P030200 Cylinder 2 Misfire Detected P030300 Cylinder 3 Misfire Detected P030400 Cylinder 4 Misfire Detected

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: P01201C: Throttle / Pedal Position Sensor / Switch A Circuit Voltage Out of Range. P210015: Throttle Actuator A Control Motor Circuit Short to Battery or Open. P210019: Throttle Actuator A Control Motor Circuit Current Above Threshold. P211172: Throttle Actuator A Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: P01201C: Throttle / Pedal Position Sensor / Switch A Circuit Voltage Out of Range. P210015: Throttle Actuator A Control Motor Circuit Short to Battery or Open. P210019: Throttle Actuator A Control Motor Circuit Current Above Threshold. P211172: Throttle Actuator A Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.

cover, camshaft housing, and the timing chain covers meet. This is typically seen on the exhaust side of the engine.

Cross, and 2019 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F 41F: P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold P030000 Random/Multiple Cylinder Misfire Detected P030100 Cylinder 1 Misfire Detected P030200 Cylinder 2 Misfire Detected P030300 Cylinder 3 Misfire Detected P030400 Cylinder 4 Misfire Detected

Corolla Hybrid, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid, 2023 2024 model year Crown, and 2024 model year Grand Highlander vehicles may exhibit a high-pitched noise coming from the front HVAC blower motor while operating the air conditioner or heater. This condition does not affect the operation of the vehicle, however, a heater cover has been developed to help reduce or potentially eliminate the noise.

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: P01201C: Throttle / Pedal Position Sensor / Switch A Circuit Voltage Out of Range. P210015: Throttle Actuator A Control Motor Circuit Short to Battery or Open. P210019: Throttle Actuator A Control Motor Circuit Current Above Threshold. P211172: Throttle Actuator A Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

CABLE CORROSION CERTAIN 2021 ? 2022 MODEL YEAR RAV4 PRIME

Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to excessive corrosion to the wire harness connections at the Rear Motor Generator. Excessive corrosion can cause AM Radio Static during certain drive cycles, or the vehicle may not start.

MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F ? 41F: ?P030027 ? Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold ?P030000 ? Random/Multiple Cylinder Misfire Detected ?P030100 ? Cylinder 1 Misfire Detected ?P030200 ? Cylinder 2 Misfire Detected ?P030300 ? Cylinder 3 Misfire Detected ?P030400 ? Cylinder 4 Misfire Detected Follow the Repair Procedure in this bulletin to address these conditions.

exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

This issue is currently under investigation.

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: ?P01201C: Throttle / Pedal Position Sensor / Switch ?A? Circuit Voltage Out of Range. ?P210015: Throttle Actuator ?A? Control Motor Circuit Short to Battery or Open. ?P210019: Throttle Actuator ?A? Control Motor Circuit Current Above Threshold. ?P211172: Throttle Actuator ?A? Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions. Follow the Repair Procedure in this bulletin to address these conditions

CABLE CORROSION CERTAIN 2019 ?2022 MODEL YEAR RAV4 HYBRID AWD (Amendment)

duplicate an abnormal noise (Drone, Growl, Humming, and/or other) from the MGR at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.

Venza Hybrid vehicles may exhibit a MIL ON condition with one or both of the following Diagnostic Trouble Codes (DTCs) present: ?P24517F ? Evaporative Emission System Switching Valve Actuator Stuck Off. ?P14502A ? Fuel Tank Pressure Sensor Signal Stuck in Range.

condition accompanied by DTC(s): ?P26CA14 Engine Coolant Pump Circuit Short to Ground or Open ?P26CA31 Engine Coolant Pump No Signal

(whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the presence of a fuel odor in or around the engine bay originating at the high-pressure fuel pump of the subject vehicles.

Trouble Codes (DTCs) present: ?P0087/P008700 ? Fuel Rail/System Pressure ? Too Low ?P107A2A ? Fuel Rail Pressure Sensor (Low) Signal Stuck in Range This condition may occur when the vehicle is operated at high altitudes and temperatures, typically above 3,300 feet (1,000 meters) and at ambient temperatures above 85F (30C). The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) and the fuel suction tube assembly have been improved to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.

This issue is currently under investigation.

?Engine Maintenance Required Visit Your Dealer? on the combination meter

duplicate an abnormal noise (Drone, Growl, Humming, and/or other) from the MGR at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.

This issue is currently under investigation

of the following DTCs: P26CA12, P26CA14, P26CB71, P26CA31, P26CE37

following DTCs: P043F00, P043E00, P24007E, P24007F, P24187E

Trouble Codes (DTCs) present: ?P0087/P008700: Fuel Rail/System Pressure ? Too Low ?P107A2A: Fuel Rail Pressure Sensor (Low) Signal Stuck in Range This condition may occur when the vehicle is operated at high altitude and high temperatures; typically, above 3,300 feet (1,000 meters) and at ambient temperatures above 85F (30C). The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) and fuel suction tube assembly have been improved to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition

If the engine is equipped with an incorrectly manufactured Crankcase Case Vent, the vehicle may not comply with certain Federal emissions regulations

If the engine is equipped with an incorrectly manufactured Crankcase Case Vent, the vehicle may not comply with certain Federal emissions regulations.

If the engine is equipped with an incorrectly manufactured Crankcase Case Vent, the vehicle may not comply with certain Federal emissions regulations.

If the engine is equipped with an incorrectly manufactured Crankcase Case Vent, the vehicle may release crankcase emissions

feet (1,000 meters) and at ambient temperatures above 85F (30C). The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) and fuel suction tube assembly have been improved to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition

This issue is currently under investigation.

Harness for the Rear Motor Generator may have the appearance of being damaged or missing

in some 2016 ? 2022 model year Toyota vehicles equipped with an FKS engine

more of the following conditions: ?Milky/Discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range) and/or P052477 (Engine Oil Pressure too low [Severe]). Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

This issue is currently under investigation.

Please see T-SB-0001-26.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Questions

October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.

semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.

semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.

semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.

DTC P010012/14 is currently under investigation.

October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.

October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.

semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.

semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.

since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.

semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.

These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.

Please create TAS case and attach a store all health check. Please contact TAS for further instructions. If it is a weekend or a holiday, continue with diagnosis and repair. Please save all parts/ or details and contact TAS on the next available workday.

established, vehicle settings and/or network/cellular coverage concerns

Please see T-SB-0016-22.

Please see T-SB-0015-22.

Please see T-SB-0012-22.

established, vehicle settings and/or network/cellular coverage concerns

attempting to send commands to the vehicle. To simplify the diagnosis of this system and prevent the unnecessary replacement of parts, please refer to the procedure below.

Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

Flow Sensor Reading

Flow Sensor Reading

Flow Sensor Reading

Recirculation "A" Control Circuit 2 Circuit Current Below Threshold

Recirculation "A" Control Circuit 2 Circuit Current Below Threshold

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative.

The Pre-Delivery Service (PDS) bulletin (link below) instructs technicians to perform this initialization after the D/C Cut Fuse is installed. The Repair Manual (links below) states that when any of the following conditions are met, the seat position information in the position control ECU assembly will be cleared: ?The power switch is turned off with any of the seat switches being operated and the ECU-DCC NO.2 fuse removed. ?The power switch is turned off within 1 second of any of the seat switches being operated with the ECU-DCC NO.2 fuse removed. ?Power supplied to the position control ECU assembly is cut while the seat is moving to the memorized position.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative

?Auxiliary (12V) battery. If the hybrid vehicle is put into storage, the State-Of-Charge (SOC) of its HV battery and auxiliary battery will gradually decrease. To prevent the auxiliary battery from becoming discharged during storage, proper maintenance is necessary. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified SOC of the vehicle?s battery while in stock and ensure proper SOC at delivery. Perform the following maintenance service for the HV battery and auxiliary battery.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should test the auxiliary (12V) battery and recharge, if necessary, no more than 48 hours before delivery to the customer.

This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing the battery rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger

appropriate tool to use for diagnosis

In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

Customer feedback indicates the following areas deserve special attention when performing PDS: ?Careful inspection for paint chips/scratches and body dents/dings. ?Proper operation of electrical accessories (including interior light, clock, and radio reset). ?Interior cleanliness. ?Proper function of mechanical systems. Customer retention and proper maintenance of vehicles are and have always been a major focus for Toyota. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. (See PDS Check Sheet item 8 of ?Final Inspection and Cleaning.?) This bulletin contains the PDS procedures that apply specifically to 2022 model year RAV4, RAV4 Hybrid and RAV4 Prime vehicles. A universal PDS Check Sheet that contains PDS steps that apply to all 2022 model year Toyota vehicles has been developed. To properly perform a complete PDS, you must complete all procedures contained in this TSB as well as the universal PDS Check Sheet. In addition, if the vehicle is stored for over 30 days, be sure to follow Long-Term Vehicle Storage Guidelines.

In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should test the auxiliary (12V) battery and recharge, if necessary, no more than 48 hours before delivery to the customer.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

model year Toyota vehicles.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

model year Toyota vehicles.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

This table will be updated during each phase launch and as more details become available.

or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.

or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.

or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an Activation Card Number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system. Follow the process in this bulletin to perform the update.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an activation card number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system

which the radio screen continues to show a Bluetooth phone call in progress after the call has ended. This condition has been confirmed with multiple Android phones, including Samsung Galaxy S21 and S22, and Google Pixel 6.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs

following conditions: ?WiFi intermittently inoperative. ?DTC (Diagnostic Trouble Code) B15DB present. ?Changing the Auto Relock Timer setting also changes the Remote 2-Press unlock setting. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1210), or Premium Audio (version 1196) or earlier may exhibit one or more of the following conditions: ?Intermittent screen flashing. ?Intermittent ?Destination Assist Unavailable? pop-up message. ?Intermittent blank screen. ?Bluetooth intermittently disconnects. ?Abnormal radio playback after Destination Assist Call. ??There is no playable data? pop-up message when using USB Audio. ?Unable to answer phone calls when using Apple CarPlay. ?Clock displays the incorrect time. ?Intermittent rebooting. ??The software version doesn?t correspond? pop-up is intermittently displayed. ?Intermittent black screen when using projection navigation. ?Abnormal noise after ACC OFF/ON when using AM mode and high volume. ??Please connect USB? pop-up message when USB is already connected. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1256), or Premium Audio (version 1256) or earlier may exhibit one or more of the following conditions: ?Navigation intermittently reverses its travel. ?Android AutoTM inoperative. ?Audio mode is set to ?Off? after disconnecting USB while using Apple CarPlay. ?Intermittent black screen flash when connecting Bluetooth. ?When the MAP button is pressed, a ?Navi app is not installed? pop-up is displayed. ?Intermittent black map screen on home screen. ?Bluetooth intermittently disconnects. ?No outgoing voice when using Bluetooth Handsfree for phone call. ?Bluetooth Now Playing List song selection is slow. ?Unable to transfer phone contacts when using Bluetooth.

Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are either optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the Initialization/Update Procedure in this bulletin to perform the initialization and app updates.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

switch may exhibit water entry to the vehicle from the HVAC drain hose being disconnected from the air conditioning radiator assembly and/or a grease/oil odor emitting from the vents. This condition may be caused by paraffin wax leaking from the evaporator. Follow the repair procedure in this bulletin to address this condition.

switch may exhibit water entry to the vehicle from the HVAC drain hose being disconnected from the air conditioning radiator assembly and/or a grease/oil odor emitting from the vents. This condition may be caused by paraffin wax leaking from the evaporator.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

light to moderate braking.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

Follow the Repair Procedure in this bulletin to address this condition

or splashing noise from inside one or more door panels when driving, opening and/or closing a door, and/or braking. This condition is caused by a cavity wax/debris/substance that may block door drain holes and restrict water from draining properly. Follow the Repair Procedure in this bulletin to address this condition

or splashing noise from inside one or more door panels when driving, opening and/or closing a door, and/or braking. This condition is caused by a cavity wax/debris/substance that may block door drain holes and restrict water from draining properly. Follow the Repair Procedure in this bulletin to address this condition.

had the following Safety Recall and/or Service Campaign repairs completed

Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed

had the following Safety Recall and/or Service Campaign repairs completed

Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

and/or MGR at various vehicle speeds and normal drive conditions

and/or MGR at various vehicle speeds and normal drive conditions.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

Service Lane - Knowledge Center.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.