2013 Toyota Rav4 Ev TSBs

Please see T-SB-0057-18.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0012-21.

Please see T-SB-0044-16.

Please see T-SB-0125-20.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0010-20.

Please see T-SB-0080-19.

Please use the following procedure for removal and installation of the sun visor.

Please see T-SB-0012-13.

The Smart Key/Smart Entry systems conform to all applicable FCC rules. This bulletin details the applicable specifications for these systems.

Please see T-SB-0294-17.

Please see T-SB-0134-16.

Once the system is reset, all previously registered keys will be erased.

Once the system is reset, all previously registered keys will be erased.

This condition has been remedied, and DCM activation utilizing Techstream can now be resumed.

This is a known condition and will be remedied in the near future. Please discontinue DCM activations utilizing Techstream until further notice.

Please see T-SB-0054-13.

Instances) instead of the native Apple Podcast application.

Please see T-SB-0133-14

Please see T-SB-0185-13.

Please see T-SB-0010-14.

Please see T-SB-0108-15

Please see T-SB-0133-14.

PLEASE SEE T-SB-0108-15

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Now Available Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

Now Available Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint

December 12, 2019. This document has been updated to clarify that only authorized Toyota dealerships are authorized to confirm if the paint peeling condition is covered by this program. However, after confirming that the paint peeling condition is covered by this program, the authorized Toyota dealership may choose to coordinate to have the repainting repair performed by a non-Toyota repair facility (e.g. third-party collision repair facility, body shop, etc.).

authorized to confirm if the paint peeling condition is covered by this program. However, after confirming that the paint peeling condition is covered by this program, the authorized Toyota dealership may choose to coordinate to have the repainting repair performed by a non-Toyota repair facility (e.g. third-party collision repair facility, body shop, etc.).

Phase Repair is Now Available Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint.

Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.

and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint. The repair phase of Customer Support Program ZKG is now available. Refer to the Dealer Letter on TIS for additional information.

This document has been updated to clarify that only authorized Toyota dealerships are authorized to confirm if the paint peeling condition is covered by this program. However, after confirming that the paint peeling condition is covered by this program, the authorized Toyota dealership may choose to coordinate to have the repainting repair performed by a non-Toyota repair facility (e.g. third-party collision repair facility, body shop, etc.).

Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels.

T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.

quenching process during manufacturing.

On some vehicles, when Rapgard? is removed the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is NOT necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

THESE STAINS APPEAR TO BE UNDER THE CLEAR COAT (REPAINTING THIS AREA IS NOT NECESSARY). THE STAIN PATTERNS ARE USUALLY UNDER WRINKLES IN THE RAPGARD. THESE WRINKLES SOMETIMES TRAP WATER AND CAUSE THE PAINT TO STAIN FROM THE TRAPPED MOISTURE, ESPECIALLY ON HORIZONTAL SURFACES, SUCH AS THE HOOD, ROOF, AND TRUNK. STAINS CAN BE REMOVED BY HEATING THE STAINED SURFACE TO REMOVE THE TRAPPED MOISTURE.

Gracenote includes detailed information for songs (genre, artist, song title, album name, etc.). The Gracenote update will be included on the USB Drive Navigation Map Update SST. A Gracenote update must be performed before a Navigation Map update. A Navigation Map update is not required to complete the Gracenote update. Use the process described in this bulletin to perform the update.

Gracenote includes detailed information for songs (genre, artist, song title, album name, etc.). The Gracenote update will be included on the USB Drive Navigation Map Update SST. A Gracenote update must be performed before a Navigation Map update. A Navigation Map update is not required to complete the Gracenote update. Use the process described in this bulletin to perform the update.

T-SB-0133-14. ? The Parts Information, Required Tools & Equipment, and On-Vehicle Navigation Update sections have been updated. Service Bulletin No. T-SB-0133-14 is obsolete and any printed versions should be discarded. Toyota models equipped with the Premium HDD Navigation (AVN/AW-EMV) system require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update; however, a unique activation number is required for each vehicle. Activation numbers are provided in an Activation Card Number pamphlet available through the normal parts ordering system. Use the process described in this bulletin to perform the update.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

T-SB-0133-14. ? The Parts Information, Required Tools & Equipment, and On-Vehicle Navigation Update sections have been updated. Service Bulletin No. T-SB-0133-14 is obsolete and any printed versions should be discarded. Toyota models equipped with the Premium HDD Navigation (AVN/AW-EMV) system require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update; however, a unique activation number is required for each vehicle. Activation numbers are provided in an Activation Card Number pamphlet available through the normal parts ordering system. Use the process described in this bulletin to perform the update.

(Lollipop) or later.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

(Lollipop) or later.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

be displayed incorrectly.

drive to update the map, points of interest, Gracenote and system software. The SST is used with all vehicles to deliver the update, however a unique Activation Number is required for each vehicle. Activation Numbers are provided in an Activation Card Number (ACN) pamphlet available through the normal parts ordering system. Use the process described in this bulletin to perform the update.

T-SB-0133-14. ? The Parts Information, Required Tools & Equipment, and On-Vehicle Navigation Update sections have been updated. Toyota models equipped with the Premium HDD Navigation (AVN/AW-EMV) system require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update; however, a unique activation number is required for each vehicle. Activation numbers are provided in an Activation Card Number pamphlet available through the normal parts ordering system.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0006-13. Toyota models equipped with the Premium HDD Navigation (AVN/AW-EMV) system will periodically require an update to the Gracenote database. Gracenote includes detailed information for songs (genre, artist, song title, album name, etc.). The Gracenote update will be included on the USB Drive Navigation Map Update SST. A Gracenote update MUST be performed BEFORE a Navigation Map update. A Navigation Map update is NOT required to complete the Gracenote update.

system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.

Toyota models equipped with the Premium HDD Navigation (AVN/AW-EMV) System require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update, however a unique Activation Number is required for each ehicle. Activation Numbers are provided in an Activation Card Number (ACN) pamphlet available through the normal parts ordering system. Use the process described in this bulletin to perform the update.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

drive to update the map, points of interest, Gracenote, and system software. The SST is used with all the vehicles to deliver the update, however a unique Activation Number is required for each vehicle.

be displayed incorrectly.

This feature does work with the in-vehicle audio system either via Bluetooth or by USB cable. Details on how to access this feature are described below.

When a customer is paired by Bluetooth Hands Free and they make a Facetime Audio call the vehicle radio will treat it as a typical Bluetooth phone call. Because Facetime works differently than a typical phone call, the in-vehicle experience may not meet the customer?s expectations.

After entering into a contract, registration of an 8-digit XM Radio ID is required. This 8-digit XM Radio ID is found by turning to channel ?0? of the satellite radio.

Gracenote includes detailed information for songs (i.e., Genre, Artist, Song Title, Album Name, etc.). The Gracenote update will be included on the ?USB Drive Navigation Map Update? SST. A Gracenote update must be performed before a Navigation Map Update. A Navigation Map Update is not required to complete the Gracenote update. Use the process described in this bulletin to perform the update.

The ?delete? soft button on the multi-information display is greyed out and not selectable.

The condition may result from power interruption including: momentary blackout from the utility company, long term power outage, removing and reconnecting the charging plug, or other circumstances. Follow the procedure in this bulletin to update the multi-information display software to address this condition.

to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.

Gracenote includes detailed information for songs (eg., Genre, Artist, Song, Title, Album Name, etc.). The Gracenote update will be included on the "USB Drive Navigation Map Update" SST. A Gracenote update must be performed before a Navigation Map Update. A Navigation Map Update is not required to complete the Gracenote update. Use the process described in this bulletin to perform the update.

drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update, however a unique Activation Number is required for each vehicle. Activation Numbers are provided in an Activation Card Number (ACN) pamphlet available through the normal parts ordering system. Use the process described in the bulletin to perform the update.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Any Previous printed versions of this bulleting should be discarded. Toyota models equipped with the Premium HDD Navigation (AVN/AW-EMV) System will periodically require an update to the Gracenote Database. Gracenote includes detailed information for songs (e.g., Genre, Artist, Song Title, Album Name, etc.). The Gracenote update will be included on the "USB Drive Navigation Map Update" SST. A Gracenote update MUST be performed before a Navigation Map Update. A Navigation Map Update is NOT required to complete the Gracenote update. Use the process described in this bulletin to perform the update.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.

systems.

drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update, however a unique Activation Number is required for each vehicle. Activation Numbers are provided in an Activation Card Number (ACN) pamphlet available through the normal parts ordering system.

Gracenote includes detailed information for songs (e.g., Genre, Artist, Song Title, Album Name, etc.) The Gracenote update will be included on the "USB Drive Navigation Map Update" SST. A Gracenote update must be performed before a Navigation Map Update. A Navigation Map Update is not required to complete the Gracenote update.

navigation/audio system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.

Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.

REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY. "

REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.

SYSTEM WITH ANDROID PHONES RUNNING OS 4.4 OR LATER. CONDITION TENDS TO OCCUR TO CUSTOMERS WHO HAVE MANY PREVIOUS TEXT MESSAGES ON THEIR PHONES.

DRIVE TO UPDATE THE MAP, POINTS OF INTEREST, GRACENOTE, AND SYSTEM SOFTWARE. THE SST IS USED WITH ALL VEHICLES TO DELIVER THE UPDATE, HOWEVER A UNIQUE ACTIVATION NUMBER IS REQUIRED FOR EACH VEHICLE. ACTIVATION NUMBERS ARE PROVIDED IN AN ACTIVATION CARD NUMBER (ACN) PAMPHLET AVAILABLE THROUGH THE NORMAL PARTS ORDERING SYSTEM. USE THE PROCESS DESCRIBED IN THE BULLETIN TO PERFORM THE UPDATE.

REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY. "

(LOLLIPOP) OR LATER.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

Toyota will be sending Follow-Up Notices to remind owners whose vehicles have not yet had Safety Recall repairs completed for the campaigns listed below.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota's New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers' ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.

Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement. BEGINNING NOW: In Phase 1, the currently active phase, Toyota is preparing the repair for this condition and thus, the repair under this program is NOT AVAILABLE. During this phase, dealers should not do any repairs for this condition under this program. Beginning in August 2019, Toyota will send an owner notification letter to all owners informing them that their vehicle is covered under this Customer Support Program. During this phase, owners who have paid for repairs for this condition can seek reimbursement consideration for expenses incurred prior to September 26, 2019. A sample of this owner notification letter has been included for your reference.

Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota's New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement. BEGINNING NOW: In Phase 1, the currently active phase, Toyota is preparing the repair for this condition and thus, the repair under this program is NOT AVAILABLE. During this phase, dealers should not do any repairs for this condition under this program. Beginning in August 2019, Toyota will send an owner notification letter to all owners informing them that their vehicle is covered under this Customer Support Program. During this phase, owners who have paid for repairs for this condition can seek reimbursement consideration for expenses incurred prior to September 26, 2019. A sample of this owner notification letter has been included for your reference.

T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.

? The Parts Information section has been updated. Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Battery Replacement.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

To prevent the auxiliary battery from becoming discharged during storage, proper maintenance is necessary. Please perform the following maintenance service for the EV battery and 12-volt auxiliary battery.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for the RAV4 EV are released as field-fix procedures described in individual Service Bulletins. This bulletin details the ECU flash reprogramming process and outlines use of the Techstream Health Check Function and the Tesla Powertrain Service Diagnostics program.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

when attempting to read MIL ON information or firmware update. Utilize the troubleshooting steps provided in the recommendations section to establish communication between the Techstream TESLA software program and Gateway ECU for the following issues: * No VIN or No green light displayed * Failure of component firmware update

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Use the following procedure to reprogram the RAV4 EV Power Management Control ECU and EV Gateway Control ECU.

To prevent the auxiliary battery from becoming discharged during storage, proper maintenance is necessary.

only: On-Board Charger, Final Drive/Inverter, EV Battery. Special requirements for ordering and handling of these components are in place and require Technical Assistance System (TAS) evaluation and confirmation. Follow the procedures listed in this bulletin to assist you with diagnosis and parts ordering.

Flash calibration updates for the RAV4 EV are released as field-fix procedures described in individual Service Bulletins. This bulletin details the ECU flash reprogramming process and outlines use of the Techstream Health Check Function and the Tesla Powertrain Service Diagnostics program.

To ensure the best ownership experience, it is important to confirm the software is the most current version available. Use the following procedure to reprogram the RAV4 EV Power Management Control ECU and EV Gateway Control ECU.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION."

Please note the following information for Regional and PD associates.

Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall repairs completed in the campaign(s) listed below.

following Safety Recall repairs completed. Please note the following information for Regional and PD associates.

vehicles have not yet had campaign repairs completed.

Please see T-SB-0304-17.

Please see T-SB-0304-17.

vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the proper operation of the Smart Key system prior to vehicle delivery.

NOTE: If these steps are not followed, it's possible to damage the Service Plug installation/removal mechanism.

performance.

campaign repairs completed.

campaign repairs completed.

Diagnostic Trouble Code (DTC) P0A7A (Generator Inverter Performance) and information code 122 generator inverter fail signal detection (overcurrent due to system malfunction). Follow the Repair Procedure in this bulletin to address this condition. NOTE This Service Bulletin applies ONLY if information code 122 is present.

No other vehicle operation or performance issues are present. This may be a result of incompatibility with unapproved EV charging stations.

Some check points have been added, expanded or clarified. Bulletins are available for items in bold type.

functions during Pre-Delivery Service (PDS) following the procedures in this bulletin.

Prius Plug-in Hybrid Vehicles (PHV) and certain 2012 through 2013 RAV4 Electric Vehicles (EV). Sample Owner Letter labels are provided below for your reference.

Prius Plug-in Hybrid Vehicles (PHV) and certain 2012 through 2013 RAV4 Electric Vehicles (EV). Sample Owner Letter labels are provided below for your reference.

Prius Plug-in Hybrid Vehicles (PHV) and certain 2012 through 2013 RAV4 Electric Vehicles (EV). Sample Owner Letter labels are provided below for your reference.

Prius Plug-in Hybrid Vehicles (PHV) and certain 2012 through 2013 RAV4 Electric Vehicles (EV). Sample Owner Letter labels are provided below for your reference.

with information code 122 (Generator Inverter Fail Signal Detection). Follow the procedure in this bulletin to address this condition. NOTE This TSB applies ONLY if information code 122 is present.

No other vehicle operation or performance issues are present. This may be a result of incompatibility with unapproved EV charging stations.

The condition may result from power interruption including: momentary blackout from the utility company, long term power outage, removing and reconnecting the charging plug, or other circumstances

No other vehicle operation or performance issues are present.

NO OTHER VEHICLE OPERATION OR PERFORMANCE ISSUES ARE PRESENT. THIS MAY BE A RESULT OF INCOMPATIBILITY WITH UNAPPROVED EV CHARGING STATIONS."

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

*Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY."

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced

? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

be involved.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

An updated PTC heater is available to address this condition.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.

Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pretensioner devices did not perform as expected, please follow the steps in the recommendations section below.

seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.

significantly colder or warmer than shop temperature. Seasonal temperature change can dramatically alter tire pressure, which can cause the tire pressure warning lamp to illuminate.

converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.