2009 Toyota Matrix TSBs

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

Currently, when a new short block assembly is ordered for a vehicle, dowels pins connecting the short block to the crankcase stiffener are not present.If you are performing a short block replacement under ZE7, please order the following parts in addition to the short block, and install in the new short block upon receipt.

This TechTip contains the accepted installation method required for Toyota vehicles.

been disconnected or power to the Engine ECM has been interrupted.

This Tech Tip contains the accepted installation method required for Toyota vehicles.

power to the Engine ECM has been interrupted.

Oil Consumption repair procedure. Replacement pistons for ZE7 should be ordered based on the pistons removed from the existing cylinder block and no longer by the measurement. This Tech Tip includes information regarding production allocation and instructions for identifying piston type on subject engines. this will be published in the next revision of T-SB-0030-15

This Tech Tip contains the accepted installation method required for Toyota vehicles.

signoff sheet for excessive engine oil consumption testing on 2AZ engine models. This TSB references a Tamper Evident/Inspection Label that Toyota recommends for use during this procedure. Currently, the supplier noted in the TSB is unable to support dealer orders for this product. Toyota has placed a large bulk order of these labels and will be distributing a package containing approximately 20 tamper evident/inspection labels to your dealership. The shipment of labels is scheduled to arrive at your dealership the week of 12/22/2014. Toyota is currently working on making these labels available through the Material Distribution Center, and it is anticipated the labels will be available for dealer ordering through the MDC in late January 2015. In the meantime, if you require additionally Tamper Evident/Inspection Labels or Tape, we recommend that you source a locally available alternative product.

Warranty Enhancement Program to extend warranty coverage to address customer compaints of Excessive Engine Oil Consumption on certain 2007-2009 Camry, Certain 2007-2011 Camry Hybrid, Certain 2007-2008 Camry Solara, Certain 2009-2010, Certain 2009 Corolla Matrix, Certain 2006-2008 RAV4, Certain 2007-2009 Scion tC, and Certain 2008-2009 Scion xB vehicles equipped with a 2AZ engine.

The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.

The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.

Diagnostic Trouble Code (DTC) P0335 (Crankshaft Position Sensor ?A? Circuit) stored. The intake camshaft gear assembly has been improved to help prevent this condition.

Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.

The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.

This TechTip contains the accepted installation method required for Toyota vehicles.

been disconnected or power to the Engine ECM has been interrupted.

The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.

T-SB-0158-14, "2AZ Engine Oil Consumption Inspection Procedure," MUST be performed first BEFORE continuing with the procedure in this bulletin. Some 2006 - 2013 model year vehicles equipped with the 2AZ engine may exhibit engine oil consumption. The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.

Oil Consumption repair procedure. * Replacement pistons for ZE7 should be ordered based on the pistons removed from existing cylinder block and no longer by measurement. * This Tech Tip includes information regarding production allocation and instructions for identifying piston type on subject engines. This will be published in the next revision of T-SB-0030-15.

The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.

Currently, when a new short block assembly is ordered for a vehicle, dowels pins connecting the short block to the crankcase stiffener are not present.

The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.

This Warranty Enhancement Program will be launched in two phases due to current part production capacity limitations. Initially, Toyota will inform owners that they may seek reimbursement consideration for previous repairs to address excessive oil consumption. Additionally, owners will be advised that if they believe their vehicle has excessive engine oil consumption, they can contact an authorized Toyota dealer to have the engine oil consumption test performed to determine if they will be eligible for future part replacement once sufficient parts are available. Once sufficient parts are produced, Toyota will send a second owner notification letter to customers informing them they may seek part replacement if their vehicle has excessive engine oil consumption.

Enhancement Program to extend warranty coverage to address customer complaints of Excessive Engine Oil Consumption on Certain 2007-2009 Camry, Certain 2007-2011 Camry Hybrid, Certain 2007-2008 Camry Solara, Certain 2009-2011 Corolla, Certain 2009-2013 Corolla Matrix, Certain 2006-2008 RAV4, Certain 2007-2010 Scion tC, and Certain 2008-2015 Scion xB, vehicles equipped with a 2AZ engine.

and S-SB-0031-14 (Scion) is now available at the MDC. The bulletins will be updated to reflect the new ordering process and posted on TIS in the near future.

The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.

The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.

The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.

and S-SB-0031-14 (Scion) is now available at the MDC. The bulletins will be updated to reflect the new ordering process and posted on TIS in the near future.

The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.

The piston assembly has been changed to minimize oil consumption. Use the Inspection Procedure in this bulletin to confirm this condition.

T-SB-0158-14, "2AZ Engine Oil Consumption Inspection Procedure," MUST be performed first BEFORE continuing with the procedure in this bulletin. Some 2006 - 2013 model year vehicles equipped with the 2AZ engine may exhibit engine oil consumption. The piston assembly has been changed to minimize oil consumption. Use the following Repair Procedure to address this condition.

This Warranty Enhancement Program will be launched in two phases due to current part production capacity limitations. Initially, Toyota will inform owners that they may seek reimbursement consideration for previous repairs to address excessive oil consumption. Additionally, owners will be advised that if they believe their vehicle has excessive engine oil consumption, they can contact an authorized Toyota dealer to have the engine oil consumption test performed to determine if they will be eligible for future part replacement once sufficient parts are available. Once sufficient parts are produced, Toyota will send a second owner notification letter to customers informing them they may seek part replacement if their vehicle has excessive engine oil consumption.

Enhancement Program to extend warranty coverage to address customer complaints of Excessive Engine Oil Consumption on Certain 2007 - 2009 Camry, Certain 2007 - 2011 Camry Hybrid, Certain 2007 - 2008 Camry Solara, Certain 2009 - 2011 Corolla, Certain 2009 - 2013 Corolla Matrix, Certain 2006 - 2008 RAV4, Certain 2007 - 2010 Scion tC, and Certain 2008 - 2015 Scion xB, vehicles equipped with a 2AZ engine.

TOYOTA IS NOW ANNOUNCING THE PART REPLACEMENT PHASE OF WARRANTY ENHANCEMENT PROGRAM ZE7 FOR VEHICLES EXHIBITING EXCESSIVE ENGINE OIL CONSUMPTION.

THIS TECH TIP CONTAINS THE ACCEPTED INSTALLATION METHOD REQUIRED FOR TOYOTA VEHICLES.

POWER TO THE ENGINE ECM HAS BEEN INTERRUPTED.

OIL CONSUMPTION REPAIR PROCEDURE. REPLACEMENT PISTONS FOR ZE7 SHOULD BE ORDERED BASED ON THE PISTONS REMOVED FROM THE EXISTING CYLINDER BLOCK AND NO LONGER BY THE MEASUREMENT. THIS TECH TIP INCLUDES INFORMATION REGARDING PRODUCTION ALLOCATION AND INSTRUCTIONS FOR IDENTIFYING PISTON TYPE ON SUBJECT ENGINES. THIS WILL BE PUBLISHED IN THE NEXT REVISION OF T-SB-0030-15

THIS TECH TIP CONTAINS THE ACCEPTED INSTALLATION METHOD REQUIRED FOR TOYOTA VEHICLES.

2AZ OIL CONSUMPTION REPAIR PROCEDURE. H REPLACEMENT PISTONS FOR ZE7 SHOULD BE ORDERED BASED ON THE PISTONS REMOVED FROM EXISTING CYLINDER BLOCK AND NO LONGER BY MEASUREMENT. H THIS TECH TIP INCLUDES INFORMATION REGARDING PRODUCTION ALLOCATION AND INSTRUCTIONS FOR IDENTIFYING PISTON TYPE ON SUBJECT ENGINES. THIS WILL BE PUBLISHED IN THE NEXT REVISION OF T-SB-0030-15."

THE PISTON ASSEMBLY HAS BEEN CHANGED TO MINIMIZE OIL CONSUMPTION. USE THE FOLLOWING REPAIR PROCEDURE TO ADDRESS THIS CONDITION."

CURRENTLY, WHEN A NEW SHORT BLOCK ASSEMBLY IS ORDERED FOR A VEHICLE, DOWELS PINS CONNECTING THE SHORT BLOCK TO THE CRANKCASE STIFFENER ARE NOT PRESENT.IF YOU ARE PERFORMING A SHORT BLOCK REPLACEMENT UNDER ZE7, PLEASE ORDER THE FOLLOWING PARTS IN ADDITION TO THE SHORT BLOCK, AND INSTALL IN THE NEW SHORT BLOCK UPON RECEIPT."

MODEL 2006-2012 CAMRY, CAMRY HV, COROLLA, MATRIX, RAV4, SOLARA. *PE

THIS IS A PROBLEM WITH THE ENGINE CONTROL MODULE. *RM

ENGINE CONTROL. PROVIDE UPDATED THROTTLE BODY PART NUMBER INFORMATION FOR CERTAIN VEHICLES. THE DRAIN PIPE HAS BEEN ELIMINATED ON THROTTLE BODY SERVICE PARTS. *PE

Please see T-SB-0057-18.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0044-16.

Please see T-SB-0063-20.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

Please see T-SB-0010-20.

Please see T-SB-0080-19.

Please use the following procedure for removal and installation of the sun visor.

Please see T-SB-0012-13.

satisfaction.

correct pulling complaints.

settlement of the consolidated Economic Loss Class Actions. Dealerships may notice media coverage of this Fairness Hearing.

Please see T-SB-0304-17.

Please see T-SB-0134-16.

Once the system is reset, all previously registered keys will be erased.

Once the system is reset, all previously registered keys will be erased.

Please see T-SB-0054-13.

regarding the proposed settlement of the consolidated Economic Loss Class Actions related to claims of unintended acceleration until July 19, 2013.

Please see T-SB-0185-13.

Please see T-SB-0030-15.

Please see T-SB-0030-15.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

when operating the driver or passenger front window glass. In some cases, the front window may become inoperative. This may be due to loose window regulator mounting bolts. Use the following repair procedure to address this condition.

source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.

quenching process during manufacturing.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

2009-2010 MATRIX. *RM

The settlement includes Toyota?s agreement to provide a Customer Support Program (?CSP?) for 2002-2019 model year (MY) vehicles originally equipped with certain Takata airbag inflators or repaired under a recall with Takata airbag inflators to provide coverage for repairs of the airbag inflator contained in the airbag module. This CSP letter is to help clarify how to administer this coverage in accordance with the settlement. This is NOT a recall or a campaign, but is provided to reassure owners that Toyota stands behind the reliability of our vehicles.

T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

In limited cases this condition may be caused by grease contamination in the door lock switch. The following procedure is available to inspect and diagnose this condition. Replacement instructions for the door wire harness and door lock actuator are also provided in this bulletin.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.

FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION."

*PE

FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. MODEL YEARS FROM 2001-2011. *PE

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

Smart Stop Technology installed on their vehicle under LSC BST. Initial notification informing customers of the availability of Smart Stop Technology on certain models was handled by the court appointed administrator Gilardi and Company at the onset of the Class Action Settlement for Economic Loss. In addition to the initial notification, Toyota will be sending notifications to customers informing them of this LSC. These notifications are an integral part of our commitment to meet customer expectations of the Toyota products. We request your assistance in completing the Smart Stop Technology as owners receive the BST and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments.

Smart Stop Technology installed on their vehicle under LSC BST. Initial notification informing customers of the availability of Smart Stop Technology on certain models was handled by the court appointed administrator Gilardi and Company at the onset of the Class Action Settlement for Economic Loss. In addition to the initial notification, Toyota will be sending notifications to customers informing them of this LSC. These notifications are an integral part of our commitment to meet customer expectations of the Toyota products.

obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.

? The Parts Information section has been updated. Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

An insect repellent drain hose tip (ARINIX Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

SOME VEHICLES MAY EXHIBIT A MIL 'ON' CONDITION. TO ADDRESS THE CONDITION , THE FUEL PIPE PROTECTOR HAS BEEN UPDATED. *JS

SYSTEM LEAK DETECTED (VERY SMALL LEAK). *PE

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

The vehicle may also exhibit a grinding or scraping noise due to the uneven brake pad wear. An updated rear disc brake pad kit has been developed to address this condition.

equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.

inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

*Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

* Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.

INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY."

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced

? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

be involved.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.

Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Flat towing or towing where only the front or rear wheels are supported may damage the all-wheel drive system.

Please see T-SB-0304-17.

Please see T-SB-0304-17.

performance.

campaign repairs completed.

campaign repairs completed.

*NJ

reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pretensioner devices did not perform as expected, please follow the steps in the recommendations section below.

Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.

Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.

and to complete the Seat Belt Extender Worksheet. The worksheet will allow the proper fitting and selection of a Seat Belt Extender for the customer. The dealership personnel should then determine the applicable part number and place an order through Dealer Daily

seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.

cost through their local Toyota dealer. The extender is available in 6-inch, 9-inch, 12-inch, 15-inch, and 18-inch lengths. The extender is available only in black. Owners are informed of the Seat Belt Extender availability through the Owner's Manual included in each vehicle

*PE

transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly

automatic transmissions.

assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.

remanufactured automatic transmissions.

converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.

mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.

INOPERATIVE AFTER VEHICLE HAS COLD SOAKED IN SUBFREEZING AMBIENT AIR TEMPERATURES. *PE UPDATED 9/23/09. *PE

consolidated Economic L:oss Class Actions relating to claims of unintended acceleration. The new (continued) date for Fairness Hearing is July 19,2013. After the hearing TMS will provide further updates on the status and timing of the settlement.

Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.

to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.

THE CUSTOMER'S IPHONE IS CONNECTED TO THE VEHICLE VIA BLUETOOTH. THE CUSTOMER MAY COMPLAIN OF THE FOLLOWING ISSUES: WHEN RECEIVING TWO INCOMING CALLS SIMULTANEOUSLY, BOTH CALLS ARE ENDED AUTOMATICALLY. ITUNES RADIO APP DOES NOT PLAY VIA BLUETOOTH AUDIO. PODCAST AND AUDIOBOOK MEDIA PLAYBACK IS INOPERATIVE VIA BLUETOOTH AUDIO.