2021 Toyota Highlander TSBs

This may be caused by the sealant in the roof channel obstructing the proper seating position for the clip gasket.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Door (PBD) will not open or close and/or stops moving while opening or closing. A modified PBD unit assembly is available to address these conditions.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

This may be caused by the sealant in the roof channel obstructing the proper seating position for the clip gasket.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This may be caused by the sealant in the roof channel obstructing the proper seating position for the clip gasket.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

2021 MODEL YEAR IS HIGHLANDER AND HIGHLANDER HYBRID VEHICLES

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

The rear underbody holes still require the installation of body plugs at the time of Pre-Delivery inspection/Service.

developed light adhesive) for 2021 model year Toyota vehicles. The decal comes in two sizes (2.8 in. x 8 in. and 4 in. x 8 in.) for small and large hoods and will be applied to the top of PPF for all series at TLS accessory installation facilities. The decal is intended to stay affixed to the film until delivery detail/wash. Just before customer delivery, follow the Removal Procedure in this bulletin to remove the decal and any residue left by the adhesive.

PRIME, TUNDRA CERTAIN 2021-2022 4RUNNER, HIGHLANDER, HIGHLANDER HV, PRIUS PRIME, SEQUOIA, TACOMA CERTAIN 2022 PRIUS

Premium Audio system may exhibit an abnormal multi-display operation, including but not limited to: an intermittent blank screen (reverse camera still operable), rebooting (Toyota logo present, audio still playing), touch screen inputs intermittently inoperative, or intermittent screen freezing. An updated integration control module is available to address these conditions. Follow the Repair Procedure in this bulletin to address this condition

Premium Audio system may exhibit an abnormal multi-display operation, including but not limited to: an intermittent blank screen (reverse camera still operable), rebooting (Toyota logo present, audio still playing), touch screen inputs intermittently inoperative, or intermittent screen freezing. An updated integration control module is available to address these conditions. Follow the Repair Procedure in this bulletin to address this condition.

Premium Audio system may exhibit an abnormal multi-display operation, including but not limited to: an intermittent blank screen (reverse camera still operable), rebooting (Toyota logo present, audio still playing), touch screen inputs intermittently inoperative, or intermittent screen freezing. An updated integration control module is available to address these conditions. Follow the Repair Procedure in this bulletin to address this condition

various situations, including emergencies, the driver and Safety Connect operator may not be able to hear each other?s voices during a Safety Connect call

PRIME, TUNDRA CERTAIN 2021-2022 4RUNNER, HIGHLANDER, HIGHLANDER HV, PRIUS PRIME, SEQUOIA, TACOMA CERTAIN 2022 PRIUS

PRIME, TUNDRA CERTAIN 2021-2022 4RUNNER, HIGHLANDER, HIGHLANDER HV, PRIUS PRIME, SEQUOIA, TACOMA CERTAIN 2022 PRIUS

appropriate tool to use for diagnosis

One or more of the Heated Oxygen Sensors (O2) or Air Fuel ratio sensor (A/F) DTCs below could set due to a leaking exhaust system. If you encounter a vehicle with any of these DTCs

This pilot program would enable you to complete Special Service Campaign 22TC01 for DCM (Data Communication Module) Reprogramming for Safety Connect, which includes your vehicle. With your active telematics account, you are encouraged to complete this campaign using this Over-the-Air (OTA) update by following these steps: 1) To complete this update, each Team Member will use the Toyota/Lexus App installed on their phone. 2) Within a few days of this E-Mail, we will send a notification to your Toyota/Lexus app to schedule and install the update on your vehicle. 3) Click on either the notification on your lock screen or the tile in the app to review the update and then continue in the App to approve the update. 4) The night after you approve the update, the telematics module will perform the update, and you will receive a confirmation notification through the app.

RAV4 PRIME, TUNDRA CERTAIN 2021-2022 4RUNNER, HIGHLANDER, HIGHLANDER HV, PRIUS PRIME, SEQUOIA, TACOMA CERTAIN 2022 PRIUS

situations, including emergencies, the driver and Safety Connect operator may not be able to hear each other?s voices during a Safety Connect call.

various situations, including emergencies, the driver and Safety Connect operator may not be able to hear each other?s voices during a Safety Connect call

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

exhibit the following condition: ?Distorted screen when using Apple CarPlay while making a hands-free phone call. Some 2020 model year vehicles equipped with Audio Plus (version 1021) or Premium Audio (version 1021) or earlier may exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation. ?Music does not automatically resume when using Android Auto?. ?Cover art is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition. Some 2020 model year vehicles equipped with Audio Plus (version 1035) or Premium Audio (version 1035) or earlier may exhibit one or both of the following conditions: ?Abnormal screen play while using Apple CarPlay (primarily during phone calls). ?Poor sound quality during phone calls while using Apple CarPlay. Some 2020 model year vehicles equipped with Audio Plus (version 1047) or Premium Audio (version 1047) or earlier may exhibit one or more of the following conditions: ?USB audio does not resume after ignition cycle. ?Intermittent rebooting. ?Bluetooth disconnecting during a phone call when using Apple CarPlay. ?Intermittent screen freezing. ?Navigation intermittently will not boot up. ?Home Screen Audio widget is blank after a Destination Assist call. ?Song, artist, or album data missing. ?Abnormal clock operation. ?Apple CarPlay intermittently inoperative. ?Radio takes a long time to boot up. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software.

In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.

exhibit the following concern: ?Distorted screen when using Apple CarPlay while making a hands-free phone call. Some 2020 model year vehicles equipped with Audio Plus (version 1021) or Premium Audio (version 1021) or earlier may exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation ?Music does not automatically resume when using Android Auto?. ?Cover a. rt is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition Some 2020 model year vehicles equipped with Audio Plus (version 1035) or Premium Audio (version 1035) or earlier may exhibit one or both of the following conditions: ?Abnormal screen play while using Apple CarPlay (primarily during phone calls). ?Poor sound quality during phone calls while using Apple CarPlay. Some 2020 model year vehicles equipped with Audio Plus (version 1047) or Premium Audio (version 1047) or earlier may exhibit one or more of the following conditions: ?USB audio does not resume after ignition cycle. ?Intermittent rebooting. ?Bluetooth disconnecting during a phone call when using Apple CarPlay. ?Intermittent screen freezing. ?Navigation intermittently will not boot up. ?Home Screen Audio widget is blank after a Destination Assist call. ?Song, artist, or album data missing. ?Abnormal clock operation. ?Apple CarPlay intermittently inoperative. ?Radio takes a long time to boot up. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software

This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing the battery rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery.

In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.

Customer feedback indicates the following areas deserve special attention when performing PDS: ?Careful inspection for paint chips/scratches and body dents/dings. ?Proper operation of electrical accessories (including interior light, clock, and radio reset). ?Interior cleanliness. ?Proper function of mechanical systems. Customer retention and proper maintenance of vehicles are and have always been a major focus for Toyota. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. (See PDS Check Sheet item 8 of ?Final Inspection and Cleaning.?) This bulletin contains the PDS procedures which apply specifically to 2021 model year Highlander and Highlander Hybrid vehicles. A universal PDS Check Sheet that contains PDS steps that apply to all 2021 model year Toyota vehicles has been developed. To properly perform a complete PDS, you must complete all procedures contained in this TSB as well as the universal PDS Check Sheet. In addition, if the vehicle is stored for over 30 days, be sure to follow Long-Term Vehicle Storage Guidelines.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should check battery SOC and recharge, if necessary, no more than 48 hours before delivery to the customer.

In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.

lashing holes are intended to be plugged during Pre-Delivery Service (PDS) -The plugs are: oRequired for anti-corrosion purposes oUsually located in the glove box prior to PDS -The number of plugs may be different based on model and production location

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should check battery SOC and recharge, if necessary, no more than 48 hours before delivery to the customer.

angle before performing axis beam adjustment. When used in conjunction with the repair manual, these BSM tips leverage SSTs and readily available tools to support sensor angle confirmation in varying shop environments.

Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing extended coverage under this Customer Support Program for repairs related to excessive corrosion to the wire harness connections at the Rear Motor Generator. Excessive corrosion can cause AM Radio Static during certain drive cycles, or the vehicle may not start.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

duplicate an abnormal noise (Drone, Growl, Humming, and/or other) from the MGR at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.

Venza Hybrid vehicles may exhibit a MIL ON condition with one or both of the following Diagnostic Trouble Codes (DTCs) present: ?P24517F ? Evaporative Emission System Switching Valve Actuator Stuck Off. ?P14502A ? Fuel Tank Pressure Sensor Signal Stuck in Range.

(whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the presence of a fuel odor in or around the engine bay originating at the high-pressure fuel pump of the subject vehicles.

?Engine Maintenance Required Visit Your Dealer? on the combination meter

duplicate an abnormal noise (Drone, Growl, Humming, and/or other) from the MGR at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.

This issue is currently under investigation

model year Sienna vehicles equipped with a 2GR-FKS engine may exhibit a knocking noise from the vacuum pump at idle.

Harness for the Rear Motor Generator may have the appearance of being damaged or missing

year Sienna, and 2016 ? 2023 model year Tacoma vehicles equipped with a 2GR-FKS engine may exhibit a knocking noise from the vacuum pump at idle. Follow the Repair Procedure in this bulletin to address this condition

with Diagnostic Trouble Codes (DTCs) P0087 (Fuel Rail/System Pressure ? Too Low) and/or P107A2A (Fuel Rail Pressure Sensor (Low) Signal Stuck in Range) present. This condition may occur when the vehicle is operated at high altitude and high temperature; typically, above 3,300 feet (1,000 meters) and ambient temperature above 85F (30C). The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Follow the Repair Procedure in this bulletin to address this condition

?Engine Maintenance Required Visit Your Dealer? on the combination meter.

following DTCs: P043F00, P043E00, P24007E, P24007F, P24187E

?Engine Maintenance Required Visit Your Dealer? on the combination meter.

engine oil leak condition from the No.2 Oil pan. This issue is currently under investigation. Please take detailed pictures of the oil pan leak condition before repair. If condition is on applicable vehicles with engine serial numbers that do not start with F or G, disregard, and proceed with normal repair.

Harness for the Rear Motor Generator may have the appearance of being damaged or missing

in some 2016 ? 2022 model year Toyota vehicles equipped with an FKS engine

This issue is currently under investigation. Please take detailed pictures of the oil pan leak condition before repair

more of the following conditions: ?Milky/Discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range) and/or P052477 (Engine Oil Pressure too low [Severe]). Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

in some 2016 ? 2021 model year Toyota vehicles equipped with an FKS engine.

Please see T-SB-0001-26.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Please see T-SB-0013-24.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.

established, vehicle settings and/or network/cellular coverage concerns

Please see T-SB-0024-22.

established, vehicle settings and/or network/cellular coverage concerns

attempting to send commands to the vehicle. To simplify the diagnosis of this system and prevent the unnecessary replacement of parts, please refer to the procedure below.

Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.

?Abnormal Operation? condition from the rear differential front coupling. In some cases, even an ?AWD System Message? with or without a DTC may be present with or without other conditions present.

being established, vehicle settings and/or network/cellular coverage concerns.

being established, vehicle settings and/or network/cellular coverage concerns.

diagnostic information in one document.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an Activation Card Number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system. Follow the process in this bulletin to perform the update.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an activation card number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system

exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation. ?Music does not automatically resume when using Android Auto?. ?Cover art is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition.

which the radio screen continues to show a Bluetooth phone call in progress after the call has ended. This condition has been confirmed with multiple Android phones, including Samsung Galaxy S21 and S22, and Google Pixel 6.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs

following conditions: ?WiFi intermittently inoperative. ?DTC (Diagnostic Trouble Code) B15DB present. ?Changing the Auto Relock Timer setting also changes the Remote 2-Press unlock setting. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1210), or Premium Audio (version 1196) or earlier may exhibit one or more of the following conditions: ?Intermittent screen flashing. ?Intermittent ?Destination Assist Unavailable? pop-up message. ?Intermittent blank screen. ?Bluetooth intermittently disconnects. ?Abnormal radio playback after Destination Assist Call. ??There is no playable data? pop-up message when using USB Audio. ?Unable to answer phone calls when using Apple CarPlay. ?Clock displays the incorrect time. ?Intermittent rebooting. ??The software version doesn?t correspond? pop-up is intermittently displayed. ?Intermittent black screen when using projection navigation. ?Abnormal noise after ACC OFF/ON when using AM mode and high volume. ??Please connect USB? pop-up message when USB is already connected. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1256), or Premium Audio (version 1256) or earlier may exhibit one or more of the following conditions: ?Navigation intermittently reverses its travel. ?Android AutoTM inoperative. ?Audio mode is set to ?Off? after disconnecting USB while using Apple CarPlay. ?Intermittent black screen flash when connecting Bluetooth. ?When the MAP button is pressed, a ?Navi app is not installed? pop-up is displayed. ?Intermittent black map screen on home screen. ?Bluetooth intermittently disconnects. ?No outgoing voice when using Bluetooth Handsfree for phone call. ?Bluetooth Now Playing List song selection is slow. ?Unable to transfer phone contacts when using Bluetooth.

following conditions: ?WiFi intermittently inoperative. ?DTC (Diagnostic Trouble Code) B15DB present. ?Changing the Auto Relock Timer setting also changes the Remote 2-Press unlock setting. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1210), or Premium Audio (version 1196) or earlier may exhibit one or more of the following conditions: ?Intermittent screen flashing. ?Intermittent ?Destination Assist Unavailable? pop-up message. ?Intermittent blank screen. ?Bluetooth intermittently disconnects. ?Abnormal radio playback after Destination Assist Call. ??There is no playable data? pop-up message when using USB Audio. ?Unable to answer phone calls when using Apple CarPlay. ?Clock displays the incorrect time. ?Intermittent rebooting. ??The software version doesn?t correspond? pop-up is intermittently displayed. ?Intermittent black screen when using projection navigation. ?Abnormal noise after ACC OFF/ON when using AM mode and high volume. ??Please connect USB? pop-up message when USB is already connected. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1256), or Premium Audio (version 1256) or earlier may exhibit one or more of the following conditions: ?Navigation intermittently reverses its travel. ?Android AutoTM inoperative. ?Audio mode is set to ?Off? after disconnecting USB while using Apple CarPlay. ?Intermittent black screen flash when connecting Bluetooth. ?When the MAP button is pressed, a ?Navi app is not installed? pop-up is displayed. ?Intermittent black map screen on home screen. ?Bluetooth intermittently disconnects. ?No outgoing voice when using Bluetooth Handsfree for phone call. ?Bluetooth Now Playing List song selection is slow. ?Unable to transfer phone contacts when using Bluetooth.

?Loading?? then a blank screen when pressing the MAP button. When performing the Storage Check in the Radio Diagnostic Menu, the MEU Storage Check displays: NG.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

exhibit one or more of the following conditions: ?Intermittent blank screen. ?Navigation map update fails. ?Album art inoperative. ?Pause function intermittently inoperative in CD mode. ?Intermittent DTC B15FE present. ?Abnormal energy flow screen appearance on Hybrid models. ?Abnormal phone call operation during Apple CarPlay. ??No Information? displayed in Information Screen. ?No audio after voice guidance in Android Auto. ?Abnormal charging scheduling operation on RAV4 Prime models. ?Abnormal XM operation when using Apple CarPlay. Follow the Multimedia Software Update Procedure in this bulletin to install the latest software version.

of the following conditions: ?WiFi intermittently inoperative. ?DTC B15DB present. ?Changing the Auto Relock Timer setting also changes the Remote 2-Press unlock setting. Some 2020 ? 2021 model year Tundra, RAV4, RAV4 Hybrid, Highlander, or Highlander Hybrid vehicles equipped with Audio Plus (version 1210), or Premium Audio (version 1196) or earlier may exhibit one or more of the following conditions: ?Intermittent screen flashing. ?Intermittent ?Destination Assist Unavailable? pop-up message. ?Intermittent blank screen. ?Bluetooth intermittently disconnects. ?Abnormal radio playback after Destination Assist Call. ??There is no playable data? pop-up message when using USB Audio. ?Unable to answer phone calls when using Apple CarPlay. ?Clock displays the incorrect time. ?Intermittent rebooting. ??The software version doesn?t correspond? pop-up is intermittently displayed. ?Intermittent black screen when using projection navigation. ?Abnormal noise after ACC OFF/ON when using AM mode and high volume. ??Please connect USB? pop-up message when USB is already connected. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software.

Premium Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are either optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the Initialization/Update Procedure in this bulletin to perform the initialization and app updates.

Premium Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are either optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the Initialization/Update Procedure in this bulletin to perform the initialization and app updates.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are either optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the Initialization/Update Procedure in this bulletin to perform the initialization and app updates.

2021 MODEL YEAR HIGHLANDER HYBRID

This can allow water to leak into the interior area of the vehicle, behind the third-row seat, when the vehicle is exposed to wet environmental conditions like rain or a car wash.

2021 MODEL YEAR HIGHLANDER HYBRID

This can allow water to leak into the interior area of the vehicle, behind the third-row seat, when the vehicle is exposed to wet environmental conditions like rain or a car wash.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

the Fuel Inlet Limited Service Campaign 22TD02

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

switch may exhibit water entry to the vehicle from the HVAC drain hose being disconnected from the air conditioning radiator assembly and/or a grease/oil odor emitting from the vents. This condition may be caused by paraffin wax leaking from the evaporator. Follow the repair procedure in this bulletin to address this condition.

switch may exhibit water entry to the vehicle from the HVAC drain hose being disconnected from the air conditioning radiator assembly and/or a grease/oil odor emitting from the vents. This condition may be caused by paraffin wax leaking from the evaporator.

This issue could involve deteriorated catalyst material from the bank 1 or bank 2 catalytic converter.

This issue could involve deteriorated catalyst material from the bank 1 or bank 2 catalytic converter.

2021 Model Year Highlander and Highlander Hybrid Sealant for a Seam near the Fuel Inlet

CERTAIN 2021 MODEL YEAR HIGHLANDER HYBRID

This can allow water to leak into the interior area of the vehicle, behind the third-row seat, when the vehicle is exposed to wet environmental conditions like rain or a car wash.

estimated in the vehicle display accurately indicate the approximate amount of remaining fuel in the fuel tank. However, some drivers are continuing to drive after the low fuel light illuminates, causing them to potentially run out of fuel and be inconvenienced. NOTE: Highlander HV fuel gauge issues, such as, fuel gauge not reading full or tank capacity does not meet expectations DO NOT apply to 21TC05.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

had the following Safety Recall or Service Campaign repairs completed.

Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had the Service Campaign repair completed in the campaign listed

had the following Safety Recall and/or Service Campaign repairs completed

Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed

had the following Safety Recall and/or Service Campaign repairs completed

Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed

stores and causing dealer stock to age. Due to this situation, dealers are reminded and recommended to follow the Long-Term Vehicle Storage Guidelines outlined in T-SB-0009-19 and other Service Bulletin publications to ensure customers receive their vehicles in a fresh and well maintained condition Please ensure that both Sales and Service at your dealership are aware of these guidelines and are following the recommended maintenance and storage processes and procedures to ensure the highest customer satisfaction with their new vehicle purchase.

conditioner does not cool due to a leak and/or corrosion in the rear underbody air conditioner tube and accessory assembly. The anti-corrosion material has been updated to reduce the possibility of this condition.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

Highlander, Highlander Hybrid, and Corolla, and 2021 model year Sienna Hybrid vehicles may exhibit decreased front windshield defroster performance at extremely low ambient temperatures. This condition may be the result of the fresh/recirculation servo actuator separating from the servo. This condition does not affect the airflow of the defroster. Follow the Repair Procedure in this bulletin to address this condition.

The various 1234YF compressor oils (ND-12, PS-D1, or VC100YF) are available through the Toyota Approved Dealer Equipment website.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

regenerative braking to hydraulic braking under certain driving conditions, such as while driving downhill, or turning with light brake pedal application. The brake actuator control module can be updated to improve brake feeling for this condition. Follow the Repair Procedure in this bulletin to address this condition.

Service Lane - Knowledge Center.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

model year Toyota vehicles.

model year Toyota vehicles.

model year Toyota vehicles.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Refer to the Tire Positioning Procedure in this bulletin to ensure that the original tires stay in the same location on the vehicle.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Refer to the Tire Positioning Procedure in this bulletin to ensure that the original tires stay in the same location on the vehicle.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Refer to the Tire Positioning Procedure in this bulletin to ensure that the original tires stay in the same location on the vehicle.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

whistle noise from the front when driving over 35 mph. This may be caused by the radiator grille bracket. A new radiator grille bracket has been developed to address this condition

whine or grind noise from the transmission. This condition may be caused by an issue with the front carrier assembly pinion shafts. Follow the Repair Procedure in this bulletin to address this condition.