2023 Toyota Corolla Cross TSBs

This condition may be present at the front and/or rear of one or both roof rails.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

This condition may be present at the front and/or rear of one or both roof rails.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

rear roof rail

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

rear roof rail

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.

configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU.

The GTS+ Software Health Check Results screen has been enhanced to help identify if a replacement ECU requires an ECU Security Key.

LG-N210hh1V1V-09 may exhibit a condition in which the remote climate system is inoperative after the vehicle has been off for three hours or more. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hatchback, Corolla Hybrid, Crown, GR Corolla, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles and 2024 model year Grand Highlander and Grand Highlander Hybrid vehicles with DCM firmware versions earlier than LG-N210jj3333-09, LG-N210nn1212-09, LG-N310kk4646-0I, LG-N310ll4A4A-0I, LG-N310mm8A8A-0I, LG-N310nnBLBM-0I, or LG-N310oo1B1B-0I may exhibit a condition in which remote services are inoperative. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Highlander, and Highlander Hybrid vehicles, 2023 2024 model year Corolla Hybrid, GR Corolla, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles, 2024 model year Grand Highlander, Grand Highlander Hybrid, and Land Cruiser vehicles; 2023 2025 Corolla Hatchback and Crown vehicles, and 2025 Crown Signia vehicles with DCM firmware versions earlier than LG-N210qq####-## or LG-N310qq####-## may exhibit a condition in which Apple Music or Amazon Music streaming and/or remote services are inoperative. A DCM firmware update is now available.

LG-N210hh1V1V-09 may exhibit a condition in which the remote climate system is inoperative after the vehicle has been off for three hours or more. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hatchback, Corolla Hybrid, Crown, GR Corolla, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles and 2024 model year Grand Highlander, and Grand Highlander Hybrid vehicles with previous versions of DCM firmware (see Table 1 below) may exhibit a condition in which remote services are inoperative. A DCM firmware update is now available to address this condition.

LG-N210hh1V1V-09 may exhibit a condition in which the remote climate system is inoperative after the vehicle has been off for three hours or more. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hatchback, Corolla Hybrid, Crown, GR Corolla, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles and 2024 model year Grand Highlander, and Grand Highlander Hybrid vehicles with previous versions of DCM firmware (see Table 1 below) may exhibit a condition in which remote services are inoperative. A DCM firmware update is now available to address this condition.

COROLLA CROSS, COROLLA HATCHBACK, COROLLA HV, GR COROLLA, CROWN, HIGHLANDER, HIGHLANDER HV, PRIUS, RAV4, RAV4 PRIME, RAV4 HV, VENZA HV

This results in all connected services becoming inoperative, including Safety Connect features such as the SOS emergency calling feature.

This results in all connected services becoming inoperative, including Safety Connect features such as the SOS emergency calling feature.

COROLLA CROSS, COROLLA HATCHBACK, COROLLA HV, GR COROLLA, CROWN, HIGHLANDER, HIGHLANDER HV, PRIUS, RAV4, RAV4 PRIME, RAV4 HV, VENZA HV

This results in all connected services becoming inoperative, including Safety Connect features such as the SOS emergency calling feature.

This results in all connected services becoming inoperative, including Safety Connect features such as the SOS emergency calling feature.

configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU. REVISION NOTICE April 18, 2024 Rev2: Applicability has been updated to include 2024 model year Tundra, Tundra Hybrid, Venza Hybrid, bZ4X, Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hybrid, Crown, GR Corolla, Corolla Hatchback, Prius, Prius Prime, Sequoia Hybrid, Highlander, Grand Highlander, Grand Highlander Hybrid, Land Cruiser, Tacoma, Tacoma Hybrid, and Mirai vehicles and 2023 model year Corolla Hatchback and Prius Prime vehicles. The Introduction section has been updated. The Operation Procedure section has been removed. The Standard ECU Configuration Procedure and ECU Configuration Value Writing Procedure sections have been added.

The GTS+ Software Health Check Results screen has been enhanced to help identify if a replacement ECU requires an ECU Security Key. REVISION NOTICE April 11, 2024 Rev2: Applicability has been updated to include 2023 2024 model year 86, Corolla, Corolla Cross, Corolla Cross Hybrid, Crown, GR Corolla, Mirai, Prius, Prius Prime, RAV4 Prime, Sequoia Hybrid, Sienna Hybrid, Tundra, Tundra Hybrid, Venza Hybrid, and Yaris and 2024 model year bZ4X, Highlander, Highlander Hybrid, Grand Highlander, and Grand Highlander Hybrid vehicles. The entire bulletin has been updated to represent GTS+ Software. July 08, 2022 Rev1: Applicability has been updated to include 2022 model year 86, Corolla Cross, Mirai, Tundra, and Tundra Hybrid vehicles and 2023 model year bZ4X vehicles. Any previous printed versions of this bulletin should be discarded.

configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU. REVISION NOTICE April 18, 2024 Rev2: Applicability has been updated to include 2024 model year Tundra, Tundra Hybrid, Venza Hybrid, bZ4X, Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hybrid, Crown, GR Corolla, Corolla Hatchback, Prius, Prius Prime, Sequoia Hybrid, Highlander, Grand Highlander, Grand Highlander Hybrid, Land Cruiser, Tacoma, Tacoma Hybrid, and Mirai vehicles and 2023 model year Corolla Hatchback and Prius Prime vehicles. The Introduction section has been updated. The Operation Procedure section has been removed. The Standard ECU Configuration Procedure and ECU Configuration Value Writing Procedure sections have been added.

The GTS+ Software Health Check Results screen has been enhanced to help identify if a replacement ECU requires an ECU Security Key. REVISION NOTICE April 11, 2024 Rev2: Applicability has been updated to include 2023 2024 model year 86, Corolla, Corolla Cross, Corolla Cross Hybrid, Crown, GR Corolla, Mirai, Prius, Prius Prime, RAV4 Prime, Sequoia Hybrid, Sienna Hybrid, Tundra, Tundra Hybrid, Venza Hybrid, and Yaris and 2024 model year bZ4X, Highlander, Highlander Hybrid, Grand Highlander, and Grand Highlander Hybrid vehicles. The entire bulletin has been updated to represent GTS+ Software. July 08, 2022 Rev1: Applicability has been updated to include 2022 model year 86, Corolla Cross, Mirai, Tundra, and Tundra Hybrid vehicles and 2023 model year bZ4X vehicles. Any previous printed versions of this bulletin should be discarded.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.

configuration software when the Electronic Control Unit (ECU) is replaced. Techstream software has been modified to indicate when configuration software is required. A new Configure column has been added to the Techstream Health Check Results screen to show when configuration software is available for a specific ECU. Follow the Operation Procedure in this bulletin to complete the ECU Software Configure Process.

CROSS HV 2023 Bz4x

CROSS HV 2023 BZ4X

Corolla Cross HV Certain 2023 Model Year bZ4x Certain 2021-2023 Model Year Sienna HV TSS 3.0 Forward Recognition Camera Software Update

uses the forward recognition camera. In rare cases, a software programming issue can damage the forward recognition camera. This will result in the Pre-Collision System not working the next time the car is started.

CROSS HV 2023 BZ4X

Corolla Cross HV Certain 2023 Model Year bZ4x Certain 2021-2023 Model Year Sienna HV TSS 3.0 Forward Recognition Camera Software Update

uses the forward recognition camera. In rare cases, a software programming issue can damage the forward recognition camera. This will result in the Pre-Collision System not working the next time the car is started.

CROSS HV 2023 BZ4X

Corolla Cross HV Certain 2023 Model Year bZ4x Certain 2021-2023 Model Year Sienna HV TSS 3.0 Forward Recognition Camera Software Update

uses the forward recognition camera. In rare cases, a software programming issue can damage the forward recognition camera. This will result in the Pre-Collision System not working the next time the car is started.

CROSS HV 2023 BZ4X

Corolla Cross HV Certain 2023 Model Year bZ4x Certain 2021-2023 Model Year Sienna HV TSS 3.0 Forward Recognition Camera Software Update

uses the forward recognition camera. In rare cases, a software programming issue can damage the forward recognition camera. This will result in the Pre-Collision System not working the next time the car is started.

model year Toyota vehicles.

model year Toyota vehicles.

and 2019 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F 41F: P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold P030000 Random/Multiple Cylinder Misfire Detected P030100 Cylinder 1 Misfire Detected P030200 Cylinder 2 Misfire Detected P030300 Cylinder 3 Misfire Detected P030400 Cylinder 4 Misfire Detected

Cross, and 2019 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F 41F: P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold P030000 Random/Multiple Cylinder Misfire Detected P030100 Cylinder 1 Misfire Detected P030200 Cylinder 2 Misfire Detected P030300 Cylinder 3 Misfire Detected P030400 Cylinder 4 Misfire Detected

one or both of the following Diagnostic Trouble Codes (DTCs) present: P11EA00 (Bank 1 Air-Fuel Ratio Imbalance (Port)) P013A7C (A/F Sensor Rich to Lean Bank 1 Sensor 2 Slow Response) There are no drivability issues or other symptoms associated with this condition.

operation where the stop and start system does one or both of the following: Does not restart the engine. Reactivates after being manually canceled. The stop and start ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to correct this condition. Follow the Repair Procedure in this bulletin to address this condition.

vehicles with M20A-FKS or M20A-FXS engines may exhibit an oil leak that originates between the oil pan sub-assembly and the stiffening crankcase assembly.

Diagnostic Trouble Code (DTC) P11EA00 (Bank 1 Air-Fuel Ratio Imbalance (Port)) present. There are no drivability issues or other symptoms associated with this condition.

Diagnostic Trouble Code (DTC) P11EA00 (Bank 1 Air-Fuel Ratio Imbalance (Port)) present. There are no drivability issues or other symptoms associated with this condition.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

operation where the stop and start system does one or both of the following: ?Does not restart the engine. ?Reactivates after being manually canceled. The stop and start ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to correct this condition.

?Engine Maintenance Required Visit Your Dealer? on the combination meter

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Please see T-SB-0021-25.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

Please see T-SB-0015-25.

Please see T-SB-0011-25.

Please see T-SB-0081-24

Please see T-SB-0062-24.

Please see T-SB-0062-24.

Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

including pre-collision braking, lane departure warning, and more. Due to the programming of the software within the forward recognition camera, there is a possibility that under certain conditions, TSS functions could become inoperative for approximately 4 seconds before rebooting and becoming operational again.

including pre-collision braking, lane departure warning, and more. Due to inappropriate programming of the software within the forward recognition camera, there is a possibility that under certain conditions, TSS functions could become inoperative for approximately 4 seconds before rebooting and becoming operational again.

including pre-collision braking, lane departure warning, and more. Due to the programming of the software within the forward recognition camera, there is a possibility that under certain conditions, TSS functions could become inoperative for approximately 4 seconds before rebooting and becoming operational again.

including pre-collision braking, lane departure warning, and more. Due to inappropriate programming of the software within the forward recognition camera, there is a possibility that under certain conditions, TSS functions could become inoperative for approximately 4 seconds before rebooting and becoming operational again.

Corolla Cross, Corolla Cross Hybrid, Highlander, Highlander Hybrid, Mirai, and Sequoia Hybrid vehicles equipped with Toyota Multimedia versions earlier than version 2230.

Highlander Hybrid, and Mirai vehicles equipped with Toyota Multimedia (earlier than version 2170). This software update includes the following improvements: User Profile. User interface. Cloud navigation. Intelligent assistant voice recognition. Bug fixes.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

Highlander Hybrid, and Mirai vehicles equipped with Toyota Multimedia (earlier than version 2050). This software update includes the following improvements: ?User interface design. ?Intelligent assistant. ?Navigation lane guidance. ?Phone book search. ?Bug fixes

recommendations.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

(non-power) adjustment controls may exhibit a driver seat base that sinks or gradually lowers. This can occur due to inadvertent contact with the vertical adjusting handle.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

If non-compatible wheels or hub bolts/nuts are installed, there is increased risk that the wheel(s) could come off resulting in a crash. This service bulletin outlines the physical differences and precautions that should be taken when servicing different wheel and wheel fastener types.