2020 Toyota Camry TSBs

valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyotas New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.

and 2019 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F 41F: P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold P030000 Random/Multiple Cylinder Misfire Detected P030100 Cylinder 1 Misfire Detected P030200 Cylinder 2 Misfire Detected P030300 Cylinder 3 Misfire Detected P030400 Cylinder 4 Misfire Detected

condition in which an Engine Maintenance Required message is displayed in the Multi-Information Display (MID). Additionally, the vehicle will exhibit DTC(s) P268111 (Engine Coolant Bypass Valve Circuit Short to Ground) and/or P268115 (Engine Coolant Bypass Valve Circuit Short to Battery or Open).

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: P01201C: Throttle / Pedal Position Sensor / Switch A Circuit Voltage Out of Range. P210015: Throttle Actuator A Control Motor Circuit Short to Battery or Open. P210019: Throttle Actuator A Control Motor Circuit Current Above Threshold. P211172: Throttle Actuator A Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: P01201C: Throttle / Pedal Position Sensor / Switch A Circuit Voltage Out of Range. P210015: Throttle Actuator A Control Motor Circuit Short to Battery or Open. P210019: Throttle Actuator A Control Motor Circuit Current Above Threshold. P211172: Throttle Actuator A Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.

(whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.

(whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.

condition in which an Engine Maintenance Required message is displayed in the Multi-Information Display (MID). Additionally, the vehicle will exhibit DTC(s) P268111 (Engine Coolant Bypass Valve Circuit Short to Ground) and/or P268115 (Engine Coolant Bypass Valve Circuit Short to Battery or Open).

Cross, and 2019 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F 41F: P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold P030000 Random/Multiple Cylinder Misfire Detected P030100 Cylinder 1 Misfire Detected P030200 Cylinder 2 Misfire Detected P030300 Cylinder 3 Misfire Detected P030400 Cylinder 4 Misfire Detected

Leak Frequently Asked Questions

(whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.

(whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.

to provide coverage for Flow Shut-off Valve Coolant Leak on multiple Model & Model Year Toyota Vehicles. Although the flow shut-off valve is covered by Toyotas New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.

condition in which an Engine Maintenance Required message is displayed in the Multi-Information Display (MID). Additionally, the vehicle will exhibit DTC(s) P268111 (Engine Coolant Bypass Valve Circuit Short to Ground) and/or P268115 (Engine Coolant Bypass Valve Circuit Short to Battery or Open).

Avalon & Avalon HV, 2018-2021 Camry & Camry HV, Certain 2020-2021 Corolla, Certain 2019-2021 Corolla HB, 2020-2021 Highlander, Certain 2019-2021 RAV4 & RAV4 HV, Certain 2021 RAV4 PHV, Certain 2021 Sienna HV, Certain 2021 Venza vehicles. The specific condition covered by this program is a small engine coolant leak can occur from a specific valve that can allow coolant to drip on other parts of the vehicle. This can cause "Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. If the condition is verified, the vehicle will be repaired with a new Flow Shut-off Valve under the terms of this Customer Support Program

Shut-off Valve Coolant Leak

(whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: P01201C: Throttle / Pedal Position Sensor / Switch A Circuit Voltage Out of Range. P210015: Throttle Actuator A Control Motor Circuit Short to Battery or Open. P210019: Throttle Actuator A Control Motor Circuit Current Above Threshold. P211172: Throttle Actuator A Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14F ? 41F: ?P030027 ? Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold ?P030000 ? Random/Multiple Cylinder Misfire Detected ?P030100 ? Cylinder 1 Misfire Detected ?P030200 ? Cylinder 2 Misfire Detected ?P030300 ? Cylinder 3 Misfire Detected ?P030400 ? Cylinder 4 Misfire Detected Follow the Repair Procedure in this bulletin to address these conditions.

exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: ?P01201C: Throttle / Pedal Position Sensor / Switch ?A? Circuit Voltage Out of Range. ?P210015: Throttle Actuator ?A? Control Motor Circuit Short to Battery or Open. ?P210019: Throttle Actuator ?A? Control Motor Circuit Current Above Threshold. ?P211172: Throttle Actuator ?A? Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions. Follow the Repair Procedure in this bulletin to address these conditions

engine may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P05A074 (Active Grill Air Shutter ?A? Actuator Slipping). To address these concerns an updated radiator shutter sub-assembly was developed

(whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the presence of a fuel odor in or around the engine bay originating at the high-pressure fuel pump of the subject vehicles.

This issue is currently under investigation.

?Engine Maintenance Required Visit Your Dealer? on the combination meter

model year Sienna vehicles equipped with a 2GR-FKS engine may exhibit a knocking noise from the vacuum pump at idle.

year Sienna, and 2016 ? 2023 model year Tacoma vehicles equipped with a 2GR-FKS engine may exhibit a knocking noise from the vacuum pump at idle. Follow the Repair Procedure in this bulletin to address this condition

?Engine Maintenance Required Visit Your Dealer? on the combination meter.

following DTCs: P043F00, P043E00, P24007E, P24007F, P24187E

?Engine Maintenance Required Visit Your Dealer? on the combination meter.

This issue is currently under investigation.

in some 2016 ? 2022 model year Toyota vehicles equipped with an FKS engine

on the instrument cluster/Multi-information Display (MID) after refueling to full. Follow the Repair Procedure in this bulletin to address this condition

more of the following conditions: ?Milky/Discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range) and/or P052477 (Engine Oil Pressure too low [Severe]). Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

in some 2016 ? 2021 model year Toyota vehicles equipped with an FKS engine.

is driven in ambient temperatures below -4F (-20C) and coolant temperature is 158F (70C) ? 172F (78C). The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to address this condition. Follow the Repair Procedure in this bulletin to address this condition.

pipe sub-assembly located at the top right of the engine compartment.

pipe sub-assembly located at the top right of the engine compartment.

following DTCs (P26CB71, P26CA14, and P26CA31) and/or coolant leak from electric water pump body or electrical connector.

The engine ECU in the involved vehicles includes certain erroneous transmission related calibration values. As a result, this software does not match the version intended to be used on production vehicles.

As a result, this software does not match the version intended to be used on production vehicles.

As a result, this software does not match the version intended to be used on production vehicles.

As a result, this software does not match the version intended to be used on production vehicles.

As a result, this software does not match the version intended to be used on production vehicles.

CAMRY 2020 AVALON

The engine ECU in the involved vehicles includes certain erroneous transmission related calibration values. As a result, this software does not match the version intended to be used on production vehicles.

Please contact TAS if you have a vehicle that exhibits a leak from the Transmission Side Cover with no signs of damage or other conditions unrelated to regardless of miles or months in service. If it?s a Sunday or holiday continue with diagnosis and repair, save all parts and details, contact TAS on the next available work day and review details with TAS engineer.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

injectors manually on 2GR-FKS engines. When direct injection is started and then stopped using the active test, current ECU logic does not turn off the direct injectors and can cause DTCs P017200, P017500 and P0160300. To avoid this condition, technicians should raise engine RPM when changing back and forth between the Direct Injection and Port Injection active tests. Use the recommended procedure below to avoid this concern while testing injection mode of FKS equipped vehicles. NOTE: If the active test is used multiple times without using this procedure to raise engine RPM, it may be necessary to reset learning values for fuel trim and Air to Fuel ratio before returning vehicle to customer.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative

appropriate tool to use for diagnosis

One or more of the Heated Oxygen Sensors (O2) or Air Fuel ratio sensor (A/F) DTCs below could set due to a leaking exhaust system. If you encounter a vehicle with any of these DTCs

This Service Bulletin should be used in conjunction with the applicable model and model year Electronic Wiring Diagram (EWD) and/or Repair Manual.

exhibit the following condition: ?Distorted screen when using Apple CarPlay while making a hands-free phone call. Some 2020 model year vehicles equipped with Audio Plus (version 1021) or Premium Audio (version 1021) or earlier may exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation. ?Music does not automatically resume when using Android Auto?. ?Cover art is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition. Some 2020 model year vehicles equipped with Audio Plus (version 1035) or Premium Audio (version 1035) or earlier may exhibit one or both of the following conditions: ?Abnormal screen play while using Apple CarPlay (primarily during phone calls). ?Poor sound quality during phone calls while using Apple CarPlay. Some 2020 model year vehicles equipped with Audio Plus (version 1047) or Premium Audio (version 1047) or earlier may exhibit one or more of the following conditions: ?USB audio does not resume after ignition cycle. ?Intermittent rebooting. ?Bluetooth disconnecting during a phone call when using Apple CarPlay. ?Intermittent screen freezing. ?Navigation intermittently will not boot up. ?Home Screen Audio widget is blank after a Destination Assist call. ?Song, artist, or album data missing. ?Abnormal clock operation. ?Apple CarPlay intermittently inoperative. ?Radio takes a long time to boot up. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit the following condition: ?Depleted 12V vehicle battery when in IG-OFF. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

exhibit the following concern: ?Distorted screen when using Apple CarPlay while making a hands-free phone call. Some 2020 model year vehicles equipped with Audio Plus (version 1021) or Premium Audio (version 1021) or earlier may exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation ?Music does not automatically resume when using Android Auto?. ?Cover a. rt is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition Some 2020 model year vehicles equipped with Audio Plus (version 1035) or Premium Audio (version 1035) or earlier may exhibit one or both of the following conditions: ?Abnormal screen play while using Apple CarPlay (primarily during phone calls). ?Poor sound quality during phone calls while using Apple CarPlay. Some 2020 model year vehicles equipped with Audio Plus (version 1047) or Premium Audio (version 1047) or earlier may exhibit one or more of the following conditions: ?USB audio does not resume after ignition cycle. ?Intermittent rebooting. ?Bluetooth disconnecting during a phone call when using Apple CarPlay. ?Intermittent screen freezing. ?Navigation intermittently will not boot up. ?Home Screen Audio widget is blank after a Destination Assist call. ?Song, artist, or album data missing. ?Abnormal clock operation. ?Apple CarPlay intermittently inoperative. ?Radio takes a long time to boot up. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software

This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing the battery rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.

Technicians are relying on the Techstream Healthcheck to determine if an update is possible.

The condition could reduce the efficiency of the HV battery cooling system. Perform the procedures outlined in this bulletin to address this condition.

In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.

exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation ?Music does not automatically resume when using Android Auto?. ?Cover art is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition. Some 2020 model year vehicles equipped with Audio Plus (version 1035) or Premium Audio (version 1035) or earlier may exhibit one or both of the following conditions: ?Abnormal screen play while using Apple CarPlay (primarily during phone calls). ?Poor sound quality during phone calls while using Apple CarPlay. Some 2020 model year vehicles equipped with Audio Plus (version 1047) or Premium Audio (version 1047) or earlier may exhibit one or more of the following conditions: ?USB audio does not resume after ignition cycle. ?Intermittent rebooting. ?Bluetooth disconnecting during a phone call when using Apple CarPlay. ?Intermittent screen freezing. ?Navigation intermittently will not boot up. ?Home Screen Audio widget is blank after a Destination Assist call. ?Song, artist, or album data missing. ?Abnormal clock operation. ?Apple CarPlay intermittently inoperative. ?Radio takes a long time to boot up. Some 2020 model year vehicles equipped with Audio Plus (version 1060) or Premium Audio (version 1060) or earlier may exhibit the following concern: ?Distorted screen when using Apple CarPlay while making a hands-free phone call. A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software.

In order to properly diagnose and determine the root cause it?s important to follow a structured process to identify any contributing issues and determine the proper remedy.

the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Corolla, Corolla Hybrid, and RAV4 Prime vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.

Camry Hybrid Vehicle; 2013 ? 2020 model year Avalon Hybrid Vehicle; 2016 ? 2020 model year Mirai and RAV4 Hybrid Vehicle; and 2020 model year Corolla Hybrid Vehicles may exhibit a MIL ON condition with Diagnostic Trouble Codes (DTCs) P0A80/P1AC000 and/or P0A7F/P1A8000 stored due to dust or debris buildup in the HV battery cooling fan and/or HV cooling filter. Follow the procedure in this bulletin to address this condition.

A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ?Circuit demand is too high for GFCI rating ?Worn out GFCI internal contacts ?Improper installation or wiring of GFCI breaker

The condition could reduce the efficiency of the HV battery cooling system. Perform the procedures outlined in this bulletin to address this condition.

the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. A firmware update is now available to address these conditions. Follow the Firmware Update Procedure in this bulletin to update the firmware

lashing holes are intended to be plugged during Pre-Delivery Service (PDS) -The plugs are: oRequired for anti-corrosion purposes oUsually located in the glove box prior to PDS -The number of plugs may be different based on model and production location

To simplify the diagnosis of the microphone, Safety Connect SOS button lights, and DCM (Data Communication Module/telematics transceiver) inoperative conditions, refer to the procedure below to prevent unnecessary parts replacement.

angle before performing axis beam adjustment. When used in conjunction with the repair manual, these BSM tips leverage SSTs and readily available tools to support sensor angle confirmation in varying shop environments.

exhibit one or more of the following conditions: ?Barge in function defaulted to OFF ?Limited phone book grammar ?Difficult Hand Free operation ?Abnormal Electronic Owner?s Manual operation ?Music does not automatically resume when using Android Auto? ?Cover art is not displayed ?Vehicle position isn?t sent to Destination Assist server ?System inoperative after using the return button when using voice recognition Some 2020 model year vehicles equipped with Audio Plus (version 1035) or Premium Audio (version 1035) or earlier may exhibit one or both of the following conditions: ?Abnormal screen play while using Apple CarPlay (primarily during phone calls) ?Poor sound quality during phone calls while using Apple CarPlay Some 2020 model year vehicles equipped with Audio Plus (version 1047) or Premium Audio (version 1047) or earlier may exhibit one or more of the following conditions: ?USB audio does not resume after ignition cycle ?Intermittent rebooting ?Bluetooth disconnecting during a phone call when using Apple CarPlay ?Intermittent screen freezing ?Navigation intermittently will not boot up ?Home Screen Audio widget is blank after a Destination Assist call ?Song, artist, or album data missing ?Abnormal clock operation ?Apple CarPlay intermittently inoperative ?Radio takes a long time to boot up A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software.

If there are no DTCs present and after the initial SOS light flashing sequence after ignition on, neither the red nor green light stays on in the overhead console determine if the vehicle is in shipping mode. To determine if a vehicle is experiencing this condition, connect a Techstream and navigate to: Telematics-Data List - ?Telematics Activation Status?. If this value is displayed as ?Shipping?, continue to the Shipping Mode recommendations below, and do not create a TAS case.

If there are no DTCs present and after the initial SOS light flashing sequence after ignition on, neither the red nor green light stays on in the overhead console determine if the vehicle is in shipping mode. To determine if a vehicle is experiencing this condition, connect a Techstream and navigate to: Telematics-Data List - ?Telematics Activation Status?. If this value is displayed as "Shipping", continue to the Shipping Mode recommendations below, and do not create a TAS case.

Actual average fuel economy may be negligibly higher than the certification listed on the Vehicle Window Sticker (Monroney Label).

This condition is characterized by no DTCs present and after the initial SOS light flashing sequence after ignition on, neither the red nor green light stays on in the overhead console. To determine if a vehicle is experiencing this condition, connect a Techstream and navigate to: Telematics-Data List - ?Telematics Activation Status?. If this value is displayed as ?Shipping?, continue to the recommendations below, and do not create a TAS case.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should check battery SOC and recharge, if necessary, no more than 48 hours before to customer delivery.

This condition is characterized by no DTCs present and after the initial SOS light flashing sequence after ignition on, neither the red nor green light stays on in the overhead console. To determine if a vehicle is experiencing this condition, connect a Techstream and navigate to: Telematics-Data List - ?Telematics Activation Status?. If this value is displayed as ?Shipping?, continue to the recommendations below, and do not create a TAS case.

Customer feedback indicates the following areas deserve special attention when performing PDS: ? Careful inspection for paint chips/scratches and body dents/dings. ? Proper operation of electrical accessories. ? Interior cleanliness. ? Proper function of mechanical systems. Customer retention and proper maintenance of vehicles are and have always been a major focus for Toyota. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker prior to delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. (See PDS Check Sheet item 9 of ?Final Inspection and Cleaning.?) A new PDS Check Sheet has been developed for the 2020 model year Camry/Camry HV. Some check points have been added, expanded, or clarified. Bulletins are available for items in bold type.

A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ? Circuit demand is too high for GFCI rating ? Worn out GFCI internal contacts ? Improper installation or wiring of GFCI breaker

Below is an explanation of what information is required when testing a 12V battery on the new Warranty Battery Testers.

angle before performing axis beam adjustment. When used in conjunction with the repair manual, these BSM tips leverage SSTs and readily available tools to support sensor angle confirmation in varying shop environments.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should check battery SOC and recharge, if necessary, within 48 hours of delivery to customers.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

vehicles may exhibit a condition in which the carpet underneath the door scuff plate becomes untucked and/or a carpet loop is torn. The condition(s) can occur on both the driver and front passenger sides of the vehicle. An improved floor mat No. 2 has been developed to reduce the likelihood of these conditions.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

exhibit a condition in which the carpet underneath the door scuff plate becomes untucked or a carpet loop is torn. The condition(s) can occur on both the front driver and front passenger sides of the vehicles.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

exhibit a condition in which the carpet underneath the door scuff plate becomes untucked or a carpet loop is torn. The condition(s) can occur on both the front driver and front passenger sides of the vehicles.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

glass peeling on the edges of the glass. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

exhibit a condition in which the carpet underneath the door scuff plate becomes untucked or a carpet loop is torn. The condition(s) can occur on both the front driver and front passenger sides of the vehicles.

exhibit a condition in which the carpet underneath the door scuff plate becomes untucked or a carpet loop is torn. The condition(s) can occur on both the front driver and front passenger sides of the vehicles

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process

center garnish panel and roof and/or an interior center garnish panel that is loose. Follow the Repair Procedure in this bulletin to address this condition

glass peeling on the edges of the glass. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

condition where the instrument panel left-hand and right-hand outside register assemblies reflect on a front side window glass.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.

glass peeling on the edges of the glass. Follow the Repair Procedure in this bulletin to address this condition.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

condition where the instrument panel LH and RH outside register assemblies reflect upon the side window glass.

glass peeling on the edges of the glass. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

developed light adhesive) for 2019 ? 2020 model year Toyota vehicles. The decal comes in two sizes (2.8 in. x 8 in. and 4 in. x 8 in.) for small and large hoods and will be applied to the top of PPF for all series at TLS accessory installation facilities. The decal is intended to stay affixed to the film until delivery detail/wash. Just before customer delivery, follow the procedure in this Service Bulletin to remove the decal and any residue left by the adhesive.

Please see T-SB-0001-26.

Please see T-SB-0101-24.

Please see T-SB-0097-23.

These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

mph

Please see T-SB-0088-22.

established, vehicle settings and/or network/cellular coverage concerns

established, vehicle settings and/or network/cellular coverage concerns

attempting to send commands to the vehicle. To simplify the diagnosis of this system and prevent the unnecessary replacement of parts, please refer to the procedure below.

Please see T-SB-0089-21.

Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.

?Abnormal Operation? condition from the rear differential front coupling. In some cases, even an ?AWD System Message? with or without a DTC may be present with or without other conditions present.

being established, vehicle settings and/or network/cellular coverage concerns.

being established, vehicle settings and/or network/cellular coverage concerns.

Please see T-SB-0119-20.

diagnostic information in one document.

Please see T-SB-0095-20.

established, vehicle settings and/or network/cellular coverage concerns

To simplify the diagnosis of this system and prevent the unnecessary replacement of parts, please refer to the procedure below.

attempting to send commands to the vehicle. To simplify the diagnosis of this system and prevent the unnecessary replacement of parts, please refer to the procedure below.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an Activation Card Number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system. Follow the process in this bulletin to perform the update.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an activation card number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system

exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation. ?Music does not automatically resume when using Android Auto?. ?Cover art is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

exhibit one or more of the following conditions: ?Intermittent blank screen. ?Navigation map update fails. ?Album art inoperative. ?Pause function intermittently inoperative in CD mode. ?Intermittent DTC B15FE present. ?Abnormal energy flow screen appearance on Hybrid models. ?Abnormal phone call operation during Apple CarPlay. ??No Information? displayed in Information Screen. ?No audio after voice guidance in Android Auto. ?Abnormal charging scheduling operation on RAV4 Prime models. ?Abnormal XM operation when using Apple CarPlay. Follow the Multimedia Software Update Procedure in this bulletin to install the latest software version.

loud popping noise, and/or static noise coming from the speakers. Updated amplifiers are available through the exchange program to address this condition. Follow the Repair Procedure in this bulletin to address this condition.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update; however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the head unit?s expiration date must be checked. If the expiration date is still valid, a license key may be generated without the use of an activation card number. Updating the maps without the use of an activation card number is considered an Embedded Navigation Update (refer to pg. 10) and performing this process does not extend the duration of telematic map services. If the head unit?s expiration date is expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an activation number. Utilizing an activation number will initiate a Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the Embedded Navigation Update and provide telematic map services for a period of two years from the day that the Dynamic Navigation Update is performed. Activation card numbers are provided in an activation card number pamphlet available through the normal parts ordering system.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update; however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the head unit?s expiration date must be checked. If the expiration date is still valid, a license key may be generated without the use of an activation card number. Updating the maps without the use of an activation card number is considered an Embedded Navigation Update (refer to pg. 10) and performing this process does not extend the duration of telematic map services. If the head unit?s expiration date is expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an activation number. Utilizing an activation number will initiate a Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the Embedded Navigation Update and provide telematic map services for a period of two years from the day that the Dynamic Navigation Update is performed. Activation card numbers are provided in an activation card number pamphlet available through the normal parts ordering system.

remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.

Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the Initialization/Update Procedure in this bulletin to perform the initialization and app updates.

The date that is shown could be more than one year in the future. This does not indicate any issues with the vehicle, and is only informing the user of the expiration date.

Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Connection to a wireless network is recommended for optimal functionality when downloading software via a smartphone. Download the latest Entune? 3.0 smartphone app on a smartphone. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the Initialization/Update Procedure in this bulletin to perform the initialization and app updates

The date that is shown could be more than one year in the future. This does not indicate any issues with the vehicle, and is only informing the user of the expiration date.

exhibit one or more of the following conditions: ? Barge in function defaulted to ?OFF? ? Limited phone book grammar ? Difficult Hand Free operation ? Abnormal Electronic Owner?s Manual operation ? Music doesn?t automatically resume when using Android Auto ? Cover art isn?t displayed ? Vehicle position isn?t sent to Destination Assist server ? System inoperative after using the return button when using voice recognition Some 2020 model year vehicles equipped with Audio Plus (version 1035) or Premium Audio (version 1035) or earlier may exhibit one or both of the following conditions: ? Abnormal screen play while using Apple CarPlay (primarily during phone calls) ? Poor sound quality during phone calls while using Apple CarPlay A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software.

Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update; however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the head unit?s expiration date must be checked. If the expiration date is still valid, a license key may be generated without the use of an activation card number. Updating the maps without the use of an activation card number is considered an Embedded Navigation Update (refer to pg. 9) and performing this process does not extend the duration of telematic map services. If the head unit?s expiration date is expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an activation number. Utilizing an activation number will initiate a Dynamic Navigation Update (refer to pg. 3). This Dynamic Navigation Update will perform the Embedded Navigation Update and provide telematic map services for a period of two years from the day that the Dynamic Navigation Update is performed. Activation card numbers are provided in an activation card number pamphlet available through the normal parts ordering system. Follow the process in this bulletin to perform the update.

exhibit one or more of the following conditions: ? Barge in function defaulted to ?OFF? ? Limited phone book grammar ? Difficult Hand Free operation ? Abnormal Electronic Owner?s Manual operation ? Music doesn?t automatically resume when using Android Auto ? Cover art isn?t displayed ?Vehicle position isn?t sent to Destination Assist server ? System inoperative after using the return button when using voice recognition A software update is now available to address these conditions. Follow the Software Update Procedure in this bulletin to update the software.

Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as ?ATX webserver is Down? or ?ATX error? will be displayed.

Audio Plus, and Entune? 3.0 Premium Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Connection to a wireless network is recommended for optimal functionality when downloading software via a smartphone. Download the latest Entune? 3.0 app onto the smartphone. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the procedure in this bulletin to perform the initialization and app updates. Additionally, a Safety Connect static cling is available to increase customer awareness. This bulletin also includes the vehicle identification process for Safety Connect-equipped vehicles and the static cling installation procedure.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

A new brake caliper assembly and fitting kit has been developed to address this condition. Follow the Repair Procedures in this bulletin to address this condition

noise in various driving conditions

noise in various driving conditions.

noise in various driving conditions.

noise in various driving conditions.

For customers who find these characteristics objectionable, an updated brake caliper assembly and fitting kit is now available as a service part. Follow the Repair Procedures in this bulletin to address this condition.

For customers who find these characteristics objectionable, an updated brake caliper assembly and fitting kit is now available as a service part. Follow the Repair Procedures in this bulletin to address this condition.

message on the MID (multi-information display) with Diagnostic Trouble Code (DTC) C13B0 (Electric Parking Brake ECU Malfunction) present. Follow the Repair Procedure in this bulletin to address this condition.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

The settlement includes Toyota?s agreement to provide a Customer Support Program for certain 2015-2020 model year (MY) vehicles that were not previously involved in a Safety Recall or Special Service Campaign related to the low pressure fuel pump. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

The settlement includes Toyota?s agreement to provide a Customer Support Program for certain 2014-2020 model year (MY) vehicles originally equipped with low pressure fuel pumps repaired under Safety Recall 20TA02, Safety Recall 21TA03, Safety Recall 21TA05 or Special Service Campaign 21TC03. The purpose of this Customer Support Program letter is to help clarify how to administer this coverage in accordance with the settlement.

following Diagnostic Trouble Codes (DTCs): ?DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ?DTC P0087 Fuel Rail / System Pressure ? Too Low Techstream data list analysis may reveal positive fuel trims including a no pressure condition verified by a manual fuel pressure gauge. Follow the Repair Procedure in this bulletin to address these conditions.

evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

stores and causing dealer stock to age. Due to this situation, dealers are reminded and recommended to follow the Long-Term Vehicle Storage Guidelines outlined in T-SB-0009-19 and other Service Bulletin publications to ensure customers receive their vehicles in a fresh and well maintained condition Please ensure that both Sales and Service at your dealership are aware of these guidelines and are following the recommended maintenance and storage processes and procedures to ensure the highest customer satisfaction with their new vehicle purchase.

The following procedure outlines the process to activate the DCM with the cellular network.

B15A8** DTC (most likely B15A804) in history during PDS. This DTC can be triggered during the manufacturing and/or shipping process and does not indicate a problem with the vehicle. To simplify the diagnosis of this DTC, refer to the procedure below to prevent unnecessary parts replacement.

This DTC can be triggered during the manufacturing and /or shipping process and does not indicate a problem with the vehicle. To simplify the diagnosis of this DTC, refer to the procedure below to prevent unnecessary parts replacement.

This DTC can be triggered during the manufacturing and /or shipping process and does not indicate a problem with the vehicle. To simplify the diagnosis of this DTC, refer to the procedure below to prevent unnecessary parts replacement.

This DTC can be triggered during the manufacturing and/or shipping process and does not indicate a problem with the vehicle. To simplify the diagnosis of this DTC, refer to the procedure below to prevent unnecessary parts replacement.

The following procedure outlines the process to activate the DCM with the cellular network. To begin the process below, move the vehicle to an area with cell reception.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

The various 1234YF compressor oils (ND-12, PS-D1, or VC100YF) are available through the Toyota Approved Dealer Equipment website.

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

Diagnostic Trouble Code (DTC) C1AAE is displayed. ? A camera malfunction error message is displayed on the Multi-display Unit and/or hood damage from aftermarket parts is exhibited. These conditions may be caused by an aftermarket forward recognition hood also known as a camera heater. Follow the Repair Procedure in this bulletin to address these conditions.

to complete the repairs, the various 1234YF compressor oils (ND-12, PS-D1, or VC100YF) are available through the Toyota Approved Dealer Equipment website.

model year Toyota vehicles.

model year Toyota vehicles.

or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.

or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.

or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.

model year Toyota vehicles.

Service Lane - Knowledge Center.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

Specifically, we are looking at vehicle surge/hesitation condition (inconsistent acceleration) and would like to recover detailed customer voice and vehicle data.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

steering wheel or while driving during turns.

1) Vehicles under 5,000 miles 2) Refer to the attached video as an example of the noise

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.

which the Toyota app does not accept the activation code and/or becomes inoperative, and/or the SOS call center does not receive the vehicle?s location data in a timely manner.

which the Remote Connect app does not accept the activation code and/or becomes inoperative, and/or the SOS call center does not receive the vehicle?s location data in a timely manner.

hybrid vehicle is put into storage, the State-Of-Charge (SOC) of its HV battery and auxiliary battery will gradually decrease. To prevent the auxiliary battery from becoming discharged during storage, proper maintenance is necessary. Perform the following maintenance service for the HV battery and auxiliary battery. NOTE ? BEFORE disconnecting the auxiliary battery, confirm the shift lever is in the ?P? position and apply the parking brake completely. The shift lever CANNOT be shifted from the ?P? position with the auxiliary battery disconnected. ? If the negative (?) terminal of the auxiliary battery is reconnected, even if the vehicle is powered ON (Ready ON), the hybrid system may NOT start. In this case, depress the brake pedal and press the Power button to start the hybrid system (the Ready light is ON). If the hybrid system still does NOT start (the Ready light is OFF), refer to the Repair Manual.

This issue is currently under investigation. Vehicles are being sought regardless of months in service or mileage. Only seeking vehicles with leaking transmissions with no other signs of damage to the side cover.

In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference. CAUTION ? ALWAYS verify the floor mat is designed specifically for the model and model year it is being installed in. ? ONLY use floor mats that can be secured using the retainers. ALL OEM Toyota floor mats are specifically designed to fit correctly and be secured using the retainers. ? Make sure the floor mat is properly placed on the vehicle carpet and secured with the retainers. If the driver side floor mat is NOT properly placed and secured, it could slip and interfere with the movement of the pedals during driving and may cause an accident. ? Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance to the mat. ? NEVER install more than one floor mat at a time in the driver?s seating position. ? If applicable, ANY secondary set of floor mats (based upon customer preference, such as the all-weather floor mats or other floor mats) MUST be placed in the trunk with ALL the packaging material intact. Do NOT install the secondary mat on top of the primary floor mat already installed in the driver?s seating position.

hybrid vehicle is put into storage, the State-Of-Charge (SOC) of its HV battery and auxiliary battery will gradually decrease. To prevent the auxiliary battery from becoming discharged during storage, proper maintenance is necessary. Perform the following maintenance service for the HV battery and auxiliary battery. NOTE ? BEFORE disconnecting the auxiliary battery, confirm the shift lever is in the ?P? position and apply the parking brake completely. The shift lever CANNOT be shifted from the ?P? position with the auxiliary battery disconnected. ? If the negative (?) terminal of the auxiliary battery is reconnected, even if the Power button is in the Start mode, the hybrid system may NOT start. In this case, push the Power button and select the Start mode again to start the hybrid system (the Ready light is ON). If the hybrid system still does NOT start (the Ready light is OFF), refer to the Repair Manual.

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Refer to the Tire Positioning Procedure in this bulletin to ensure that the original tires stay in the same location on the vehicle.

2020 model year Camry hybrid, 2019 ? 2020 model year Avalon, and 2019 ? 2020 model year Avalon hybrid vehicles may exhibit a condition in which the fuel filler door is difficult to open when the release button is pressed. This may be caused by the fuel filler door spring not having sufficient stroke to push the fuel filler door to the open position. The fuel filler door spring has been updated. Follow the Repair Procedure in this bulletin to address this condition.