2017 Toyota 86 TSBs

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

This material protects from acid rain, environmental fallout, and rail contamination.

wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition

The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.

T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.

On some vehicles, when Rapgard? is removed the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is NOT necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.

PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.

A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ?Circuit demand is too high for GFCI rating ?Worn out GFCI internal contacts ?Improper installation or wiring of GFCI breaker

A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ? Circuit demand is too high for GFCI rating ? Worn out GFCI internal contacts ? Improper installation or wiring of GFCI breaker

Below is an explanation of what information is required when testing a 12V battery on the new Warranty Battery Testers.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.

T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State of Charge (SOC) of the vehicle?s battery while in stock and assure proper State of Charge (SOC) at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should check battery State of Charge (SOC) and recharge, if necessary, within 48 hours of delivery to customers.

In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate Installation Procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).

Pre-Delivery Service (PDS) is a critical step in satisfying the dealership?s new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: *Careful inspection for paint chips/scratches and body dents/dings. Proper operation of electrical accessories (including interior light, clock, and radio reset). *Interior cleanliness. *Proper function of mechanical systems.

These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.

Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.

SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.

THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE.

THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE. AS A MATTER OF POLICY, TOYOTA DOES NOT PROVIDE BATTERY WARRANTY COVERAGE FOR DISCHARGED AND/OR FAILED BATTERIES DUE TO LACK OF MAINTENANCE. IT IS THE DEALERS RESPONSIBILITY TO MAINTAIN THE SPECIFIED STATE OF CHARGE (SOC) OF THE VEHICLES BATTERY WHILE IN STOCK AND ASSURE PROPER STATE OF CHARGE (SOC) AT DELIVERY. TO ELIMINATE CUSTOMER SERVICE CONCERNS DUE TO AN UNDERCHARGED BATTERY DURING THE FIRST FEW WEEKS OF OWNERSHIP, ALL DEALERS SHOULD CHECK BATTERY STATE OF CHARGE (SOC) AND RECHARGE, IF NECESSARY, WITHIN 48 HOURS OF DELIVERY TO CUSTOMERS.

IN ADDITION, SOME MODELS MAY UTILIZE RETAINING CLIPS FOR PASSENGER SIDE AND REAR SEAT FLOOR MATS AS WELL. FOLLOW THE APPROPRIATE INSTALLATION PROCEDURE TO ATTACH THE DRIVERS SIDE, AND IF APPLICABLE, THE PASSENGERS SIDE AND REAR SEAT FLOOR MATS TO THE VEHICLE CARPET USING THE FLOOR MAT RETAINING CLIPS DURING PRE-DELIVERY SERVICE (PDS).

PRE-DELIVERY SERVICE (PDS) IS A CRITICAL STEP IN SATISFYING THE DEALERSHIPS NEW CAR CUSTOMERS. CUSTOMER FEEDBACK INDICATES THE FOLLOWING AREAS DESERVE SPECIAL ATTENTION WHEN PERFORMING PDS: *CAREFUL INSPECTION FOR PAINT CHIPS/SCRATCHES AND BODY DENTS/DINGS. PROPER OPERATION OF ELECTRICAL ACCESSORIES (INCLUDING INTERIOR LIGHT, CLOCK, AND RADIO RESET). *INTERIOR CLEANLINESS. *PROPER FUNCTION OF MECHANICAL SYSTEMS.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

Service Tool Set is required to properly install the seal onto the injector. As new vehicle configurations have been released, several injector seal tool sets have been distributed to accommodate these new vehicles. There are a total of three injector seal tool sets for Toyota models, located in the appropriate SST cabinets. Each kit contains multiple pieces as shown in the diagram below. The individual pieces must remain together to ensure these tools are used correctly. Refer to the repair manual for the tool information to ensure the correct tool is used for the desired application.

THE FOLLOWING GUIDELINES SHOULD BE PERFORMED TO MINIMIZE VEHICLE COMPONENT/PART DEGRADATION DUE TO EXTENDED VEHICLE STORAGE CONDITIONS. LONG-TERM STORAGE CAN AFFECT A VEHICLES SYSTEMS AND COMPONENTS. ANY PROBLEMS THAT ARE FOUND SHOULD BE CORRECTED IMMEDIATELY.

The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.

Adding stop leak products to the A/C system is not a recommended or approved Toyota repair process. During A/C service, moisture enters the A/C system, and can react with the previously added A/C stop leak, forming a gelatinous substance. The gel substance that forms can cause the A/C compressor to bind and or seize.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.

Brake vibration can occur at any time if improper torque is applied to lug nuts. Even one lug nut over or under torqued can cause vibration.

even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface

Please see T-SB-0304-17.

Please see T-SB-0304-17.

vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected using the following procedure during Pre-Delivery Service (PDS). Note: Check ALL of the Smart Keys using this procedure.

VEHICLE WITHOUT USING A MECHANICAL KEY. TO ENSURE THE SYSTEM IS OPERATING PROPERLY, THE SMART KEY FUNCTIONS (SMART ENTRY AND SMART START) SHOULD BE INSPECTED USING THE FOLLOWING PROCEDURE DURING PRE-DELIVERY SERVICE (PDS). NOTE: CHECK ALL OF THE SMART KEYS USING THIS PROCEDURE.

These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

Should this condition occur, please contact TAS and your FTS to document repair information.

conditions: ?MIL ON condition with Diagnostic Trouble Code (DTC) P0300. ?Rough idle at cold start noticeable when engine coolant temperature is around 50F (10C). Follow the Repair Procedure in this bulletin to address this condition.

conditions: ? MIL ON condition with Diagnostic Trouble Code (DTC) P0300. ? rough idle at cold start noticeable when engine coolant temperature is around 50F (10C). Follow the Repair Procedure in this bulletin to address this condition.

T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit

The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been updated, in addition to valve adjustment to prevent this condition. Follow the Repair Procedure in this bulletin to address this condition.

Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.

Please see T-SB-0012-21.

Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates

This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.

matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the direction of rotation.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.

IF THE WHEELS ARE REPLACED OR REFINISHED BEFORE VEHICLE DELIVERY, IT IS IMPORTANT THAT THE TIRES REMAIN ON THE VEHICLE IN THE SAME LOCATION AND IN THE SAME DIRECTION OF ROTATION.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

? Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.

Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.