2003 Saturn Ion TSBs

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

conductive finish.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

issue.

issue.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

Identification.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

engine oil consumption.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.

conductive finish.

how toptier fuels should be used to reduce carbon build up.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

how toptier fuels should be used to reduce carbon build up.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

intermittent engine misfire and a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0300, P0301, and/or P0304. Technician will need to follow published Service Information diagnostics first. If the Service Information diagnostics do not isolate a cause for this concern, inspect the inside of the fuel rail and/or fuel tank for fuel contamination. f fuel contamination is present, refer to the "Fuel System Cleaning" procedure in Service Information. Dealer will need to advise the customer to only use fuel from high quality high volume Top Tier fuel stations.

On some vehicles equipped with an automatic transmission, the vehicle?s transmission shifter may not properly transmit an electrical signal that allows the ignition key to be turned counter clockwise past the accessory mode to the ?LOCK? position after the vehicle has been shifted into park. If this occurs, the ignition key cannot be removed from the ignition cylinder without depressing the manual release plunger located on the underside of the steering column as described in the owner?s manual. A key left in the accessory position for an extended period of time may result in severe battery drain and a possible no start condition. In most cases, dealers are to replace the automatic transmission shifter. This repair will be made at no charge to the customer. However, the service procedure also requires dealers to utilize the Ignition Key Cannot Be Inserted, Rotated, or Removed from the Ignition Lock Cylinder diagnostic information table in SI to eliminate other possible causes before replacing the automatic transmission shifter.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.

servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.

On some vehicles equipped with an automatic transmission, the vehicle's transmission shifter may not properly transmit an electrical signal that allows the ignition key to be turned counter clockwise past the accessory mode to the "LOCK" position after the vehicle has been shifted into park. If this occurs, the ignition key cannot be removed from the ignition cylinder without depressing the manual release plunger located on the underside of the steering column as described in the owner's manual. A key left in the accessory position for an extended period of time may result in severe battery drain and a possible no start condition. In most cases, dealers are to replace the automatic transmission shifter.

or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.

receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.

certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.

Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.

Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

SOME VEHICLES EQUIPPED WITH ELECTRIC POWER STEERING MAY EXPERIENCE A SUDDEN LOSS OF POWER STEERING ASSIST THAT COULD OCCUR AT ANY TIME WHILE DRIVING. IF THE POWER STEERING ASSIST IS LOST, A MESSAGE IS DISPLAYED ON THE DRIVER INFORMATION CENTER AND A CHIME SOUNDS TO INFORM THE DRIVER. STEERING CONTROL CAN BE MAINTAINED, AS THE VEHICLE WILL REVERT TO A MANUAL STEERING MODE, BUT WOULD REQUIRE GREATER DRIVER EFFORT AT LOW VEHICLE SPEEDS, WHICH COULD RESULT IN AN INCREASED RISK OF A CRASH. DEALERS ARE TO REPLACE THE POWER STEERING MOTOR.

A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

GASKET SEALING SURFACES.

ON DECEMBER 11, 2014, GENERAL MOTORS RELEASED SPECIAL COVERAGE ADJUSTMENT 14632. THE TOTAL NUMBER OF U.S. VEHICLES INVOLVED IS APPROXIMATELY 1.9 MILLION. IN ORDER TO ASSIST DEALERS WITH RESPONDING TO CUSTOMER INQUIRIES ABOUT THIS FIELD ACTION, ATTACHED IS A BRIEF Q&A DOCUMENT. PLEASE MAKE SURE THAT ALL EMPLOYEES WHO INTERACT WITH CUSTOMERS ARE FAMILIAR WITH THIS INFORMATION. CUSTOMER QUESTIONS THAT YOU ARE UNABLE TO ANSWER SHOULD BE REFERRED TO THE DEALER BUSINESS CENTER OR YOUR DISTRICT MANAGER - AFTERSALES.

ON SOME VEHICLES EQUIPPED WITH AN AUTOMATIC TRANSMISSION, THE VEHICLES TRANSMISSION SHIFTER MAY NOT PROPERLY TRANSMIT AN ELECTRICAL SIGNAL THAT ALLOWS THE IGNITION KEY TO BE TURNED COUNTER CLOCKWISE PAST THE ACCESSORY MODE TO THE LOCK POSITION AFTER THE VEHICLE HAS BEEN SHIFTED INTO PARK. IF THIS OCCURS, THE IGNITION KEY CANNOT BE REMOVED FROM THE IGNITION CYLINDER WITHOUT DEPRESSING THE MANUAL RELEASE PLUNGER LOCATED ON THE UNDERSIDE OF THE STEERING COLUMN AS DESCRIBED IN THE OWNERS MANUAL. A KEY LEFT IN THE ACCESSORY POSITION FOR AN EXTENDED PERIOD OF TIME MAY RESULT IN SEVERE BATTERY DRAIN AND A POSSIBLE NO START CONDITION. IN MOST CASES, DEALERS ARE TO REPLACE THE AUTOMATIC TRANSMISSION SHIFTER.

SOME 2006-2009 MODEL YEAR CHEVROLET HHR (NON-TURBO) AND 2003 MODEL YEAR SATURN ION VEHICLES EQUIPPED WITH ELECTRIC POWER STEERING MAY EXPERIENCE A SUDDEN LOSS OF POWER STEERING ASSIST THAT COULD OCCUR AT ANY TIME WHILE DRIVING. IF THE POWER STEERING ASSIST IS LOST, A MESSAGE IS DISPLAYED ON THE DRIVER INFORMATION CENTER AND A CHIME SOUNDS TO INFORM THE DRIVER. STEERING CONTROL CAN BE MAINTAINED, AS THE VEHICLE WILL REVERT TO A MANUAL STEERING MODE, BUT WOULD REQUIRE GREATER DRIVER EFFORT AT LOW VEHICLE SPEEDS, WHICH COULD RESULT IN AN INCREASED RISK OF A CRASH. DEALERS ARE TO REPLACE THE POWER STEERING MOTOR.

A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

SELECT DOCUMENT SEARCH BUTTON BELOW. GENERAL MOTORS 2003-2011 VEHICLES EQUIPPED WITH AN AUTOMATIC TRANSMISSION, UNABLE TO REMOVE IGNITION KEY. *LJ

ION: SEE DOCUMENT SEARCH BUTTON FOR OWNERS LETTER. CERTAIN VEHICLES ARE UNABLE TO REMOVE IGNITION KEY DUE TRANSMISSION SHIFTER. *LJ UPDATED 6/16/15. *PE

REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE

*RM

VEHICLE MUST BE DRIVEN BEFORE MEASURING TIRES ON EQUIPMENT HUNTER GSP9700 TOENSURE REMOVAL OF ANY FLATSPOTTING. MODELS INCLUDE ALL GM PASSENGER CARS AND LIGHT TRUCKS, AS WELL AS CERTAIN HUMMERS, SAABS, AND SATURNS. *PE

*PE UPDATED 2/17/09. *PE

*KB

*KB

*TT

*TT

*SC

*TT UPDATED 08-15-07. *KB

*EH

*EH

INCLUDING 2005-06 PONTIAC PURSUIT. *TT *SC

*TT

*SC

*TT

*TT

ELEVATED ENGINE RPM AND/OR STALL. *TT THIS BULLETIN REPLACES PREVIOUS VERSION DATED APRIL 2004. *TT

*TT

ALSO THE ENGINE MAY BE DIFFICULT TO START; ENGINE MISFIRE FOR SEVERAL SECONDS; AND/OR WHITE SMOKE OR COOLANT ODOR FROM THE TAILPIPE. *TT

THE CONDITION MAY BE CAUSED BY AERATION OF TRANSAXLE FLUID, RESULTING IN A DELAYED APPLY OF 3RD CLUTCH. CORPORATE BULLETIN NUMBER 03-07-30-052 *MN

*PH *SC

*TT UPDATE. *TT

*TT UPDATED *EH

*TT

*TT

*TT

*TT

*TT

*TT *MJ

*TT

*TT

REPLACEMENT / REMOVAL PROCEDURE AND IGNITION CYLINDER AND KEY CODE INFORMATION IN THE 2003 KEY CODE MANUAL. *TT

Allegation Resolution (PAR) claim.

Allegation Resolution (PAR) claim.

the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

Allegation Resolution (PAR) claim.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

Only).

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

correct tool.

vehicle.

additional information concerning Policy decision making.

Approved Refinish Materials booklet information.

may be un necessary.

correct tool.

vehicle.

find growing concerns around them.

may be un necessary.

may be un necessary.

correct tool.

vehicle.

Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.

by listing possible concerns to specific vehicles.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.

unwanted odors in vehicles and which products to use for each application.

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

first time.

Only)

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

may be un necessary.

find growing concerns around them.

Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.

directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.

customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.

TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

*JB

GM TECH LINK. *TT

*TT

*EH

*EH

*NM

*SC

*TT

*TT

*TT

*TT

*TT

*MJ THIS BULLETIN REPLACED PREVIOUS 04-07-30-024. *TT

*MJ

*TT

BULLETINS RELEASED IN JANUARY, FEBRUARY, AND MARCH 2004. *MR

*MN

*PH

*TT

*TT

*TT

*TT

*TT

*TT

*TT

It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

tried to provide a software update to the OnStar hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."

applications.

applications.

conductive finish.

BCM to prompt the technician to enter the mileage during programming.

application.

applications.

rules and regulations for Canada only.

drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.

it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.

parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

Communication Interface Modules (VCIM) (GMNA Only)

TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.

MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

*KB

AFTER JUMP STARTING THE VEHICLE. *KB (REPLACE FUSE AND INSTRUCT OWNER HOW TO JUMP START VEHICLE). UPDATED 2/17/10. *PE

*AK

VARIOUS MODELS INCLUDING 2005 - 2006 PONTIAC PURSUIT (CANADA ONLY). *TT

*TT

*MJ

*TT

*TT

E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

the warranty transaction submission procedures that support the Personal Property Damage process.

Only).

Spin-On Oil Filters.

the warranty transaction submission procedures that support the Personal Property Damage process.

Only).

Spin-On Oil Filters.

Spin-On Oil Filters.

Spin-On Oil Filters.

independent causes (GM Canada Dealers Only).

Spin-On Oil Filters.

Only).

Operations and Customer Enthusiasm

operations and customer enthusiasm.

comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.

that vehicles can be fixed right the first time in for service.

service.

warranty transaction submission procedures that support the Personal Property Damage process.

Operations and Customer Enthusiasm

Operations and Customer Enthusiasm

*TT

*TT TO INCLUDE 2005 SATURN VUE. *EH

Fog/Driving Lamp Damage.

Guidelines.

Guidelines.

message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

what should be considered warranty replacement and not

inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

at start up after cold soak and that this is considered a normal conditon and no repairs are necessary

SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE

2008 AND PRIOR GM PASSENGER CARS AND LIGHT DUTY TRUCKS INCLUDING 2008 AND PRIOR HUMMER H2, H3 AND 2005-08 SAAB 9-7X AND 2000-05 SATURN L SERIES AND 2003-07 SATURN ION. *KB UPDATED 4/11/08. *NJ UPDATED 5/27/09. *PE

*KB UPDATED 08-15-07. *KB UPDATED 10/09/07. *NJ UPDATED 4/3/08. *NJ

*SC

*EH UPDATED *EH

REPLACEMENT AND DRL JUMPER KIT INSTALLATION. LATEST PART AVAILABILITY AND SHORTAGE INFORMATION. STOCKING POLICY MESSAGE. *TT

*JB

*TT

*TT

*TT *SC

*TT ERRATIC FRONT TURN SIGNAL OPERATION WHEN USING A CELL PHONE CHARGER IN EITHER ACCESSORY POWER OUTLET. *TT

TransFlow.

essential tool J-45096 TransFlow.

THE SHIFT LEVER ON THE MANUAL TRANSMISSIONS ROLL PIN CAN BACK OUT AND CONTACT THE SHIFT COVER DURING A SHIFT EVENT. THIS CAN CAUSE AN INCOMPLETE, BLOCKED SHIFT OR DIFFICULTY SHIFTING THE TRANSMISSION. *PE

NEW SPECIAL REIMBURSEMENT POLICY FOR VEHICLES EQUIPPED WITH VARIABLE TRANSMISSION WITH INTELLIGENCE (VTI) TRANSMISSION-50 PERCENT OF TRANSMISSION REPAIR COST WILL BE PAID BY GM OR CUSTOMER MAY ELECT THE OPTION OF $5,000 CUSTOMER CREDIT INSTEAD OF REPAIR. CSC LETTER WAS RECEIVED. *PE

SHIFTING INTO 3RD OR 4TH GEAR, WILL NOT SHIFT INTO EITHER 3RD OR 4TH GEAR. (REPLACE COMPLETE OUTPUT SHAFT ASSEMBLY). *KB

*AK

INOPERATIVE, NOISE, SLIP, LOW PRESSURE OR LEAK RELATED CONCERN. *TT

OTHER INTERNAL TRANSAXLE OVERHAUL. *TT

*MR

*TT

SERVICE MANUAL UPDATE. *TT *MJ

*TT

*TT

*TT

*TT

*TT

*TT

*TT

*TT

*TT

*TT

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

that they only get a few channels.

Technician will need to use a scan tool and verify current Digital Radio Receiver Status under Data Display. Technician will need to look at the second line labeled Digital Radio Receiver Status will display a number of 00 - 04. Technician will repair per the status code.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.

THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.

*MJ

2003 SATURN ION AND 2004 SATURN L-SERIES. *TT

*TT

*TT

*TT

*TT

*TT

*TT

Replacement Guidelines.

Replacement Guidelines.

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

pitting corrosion and/or spotted.

*TT

*TT

*TT

*TT

*TT

*PH

*TT

*TT

*TT

*TT THIS BULLETIN REPLACED PREVIOUS VERSION DATED 08-01-03. *TT

*TT

*TT

*TT

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.

rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

using the evaporative emission cart smoke machine and ultrasonic leak detectortools.

additives.

usage of E85 fuel in GM vehicles.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

THE SES LAMP MAY BE ILLUMINATED DUE TO A P0466 DTC. *TT UPDATED 08-15-07. *KB

*SC

*TT

*TT

*TT

Information and Transaction Submissions Procedure and general content updates.

Operation.

customer wishes.

information/bulletin PI0746C.

Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.

A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

*KB UPDATED 10/18/07. *NJ

*TT

*TT

*PH

VARIOUS MODELS INCLUDING THE 2004 L-SERIES. *TT

DTC'S C0176, C0176, C0475, C0476, C0550, U2105, U2107 SET. *NJ UPDATED 2/17/10. *PE UPDATED 3/01/10. *PE

*TT UPDATED 3/30/11. *PE

*TT (REPLACE INTERMEDIATE SHAFT). UPDATED 10/05/07. *NJ UPDATED 11/02/07 *NJ

*TT

*TT

*TT

*MR

SIT BULLETIN 1416474. *TT

repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN.

BRAKE AND BRAKE PEDAL OPERATION NOT AFFECTED. *PE UPDATED 2/8/12. *PE

FRONT LOWER CONTROL ARM REAR BUSHING). *MJ UPDATED 10/5/07. *NJ UPDATED 5/20/11. *PE

SECTION OF THE 2003 SATURN ION BRAKES SERVICE MANUAL. *TT

VEHICLES THAT SHOULD NOT BE OPERATED WITH CHAINS. *JG

repairs requiring balance and Road Force measurement.

repairs requiring balance and Road Force measurement.

management submission information.

*TT

*EH

belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE

*TT

*TT THIS BULLETIN REPLACES 03-01-38-020 DATED 11/01/2003. *TT

*MR *TT