2025 Ram Promaster TSBs

illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P061B-00 - Internal Control Module Torque Calculation Performance. P1444-00 - Power Inverter Module - Incorrect Control Mode. P1E18-00 - Internal Control Module Electronic Park Performance. Customers may experience the following: At start up, the vehicle will shut down. At start up, the vehicle will not start. This bulletin involves reprogramming the EVCU with the latest available software.

illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P061B-00 - Internal Control Module Torque Calculation Performance. P1444-00 - Power Inverter Module - Incorrect Control Mode. P1E18-00 - Internal Control Module Electronic Park Performance. Customers may experience the following: At start up, the vehicle will shut down. At start up, the vehicle will not start. This bulletin involves reprogramming the EVCU with the latest available software.

Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0D08-00 - Hybrid/EV Battery Positive Contactor A Stuck Closed. U0412-00 - Invalid Data Received From Battery Energy Control Module "A". Customers may also experience one of more of the following: The Service Lamp is illuminated in the Instrument Panel Cluster (IPC). The vehicle will not enable This bulletin involves reprogramming the BPCM with the latest available software.

Rain Sensor Internal Failure.

Rain Sensor Internal Failure.

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Tire Pressure Sensors Values Are Not Displayed

Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only."

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: Rough idle. Valvetrain noise. "

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: Oil found on the ground beneath the vehicle. "

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

This bulletin involves installing the right front roof rack bracket.

This bulletin involves installing the right front roof rack bracket.

Mirror Contacts Door Window Glass In The Folded Position.

chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

chatter/streak/jump/skip/smear or make noise while traveling across the windshield.

Handle Binds When Pulled.

Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay

Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

the following: - Navigation non-functional, not updating current position. - Screen Off hard key inoperative, Soft key on radio screen still operational. - CarPlay and Android Auto stability issues. - Text cut-off in different menus or pop-up messages - Voice Recognition not working for specific voice commands

C0033-29 Right Front Tone Wheel Invalid Signal Diagnostic Trouble Code (DTC). Customer Complaint/Technician Observation: Customer complaint of intermittent or steady ABS or Electronic Stability Control (ESC) lamps on. Technician finds C0033-29 DTC stored or active. See the below information if the complaint and C0033-29 is present. Discussion: Inspection of the tone wheel should be performed. Metal dust or flakes could gather around the tone wheel area causing a false signal and resulting in the DTC setting. Repair will include disassembly, inspecting the tone wheel, removing/cleaning the debris from the hub bearing and reassembly.

Have to really press on the brake pedal to get the vehicle to stop. This bulletin involves bleeding the braking system and then properly installing the brake fluid reservoir cap."

A/C relay clutch not operating, dealers are unnecessary replacing PDCs. Battery disconnection is required to reset PCM. Please follow SOL S2624000004.

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

inoperative, replace the bulb with a TOSHIBA (W28/8W / 7444NA) bulb exclusively. If the socket is melted, replace both the bulb and socket. Do not use aftermarket bulbs.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

Service Electric Power Steering Message On Cluster.

"