2022 Ram Promaster TSBs

This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: Rough idle. Valvetrain noise. "

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: Oil found on the ground beneath the vehicle. "

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

There may be Diagnostic Trouble Codes (DTCs) present. "

Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures."

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.

INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs): ? B1053-64 RFHM (Kin Communication) - Signal Plausibility Failure Set In The RF Hub. ? B1A7D-2F Start Button - Signal Erratic. Customers may also experience one or more of the following: ? Messages shown on the Instrument Panel Cluster (IPC): ? Service Passive Entry Vehicle will not Shut Off or Restart. ? To Shut Off Vehicle, See Vehicle Settings (if the vehicle speed is lower than 4 KMH) (2.4 MPH). ? Engine will not shut off. ? Lamp lit on IPC (Fig. 1) . This bulletin involves updating the RFHM with the latest available software.

There may be Diagnostic Trouble Codes (DTCs) present.

There may be Diagnostic Trouble Codes (DTC)s present.

There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs. NOTE: **ALL VEHICLES ON THE RSU VIN LIST REQUIRE ALL 12 INTAKE HYDRAULIC LASH ADJUSTERS TO BE REPLACED**.

If no response in 15 minutes, proceed with repair.

presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.

INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.

C1205-02 Brake Light Switch General Electric Failure.

Sensor Module Missing Calibration Please perform a Steering angle sensor initialization prior to ordering and replacing the steering gear. This procedure should be done following a battery disconnect, or following steering gear replacement. This can be done by starting the engine and turning the steering wheel from lock to lock. If the manual procedure fails, Use the WiTECH tool; go to advance diagnostic SAS initialization routine.

installed in the vehicle.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0325 - Knock Sensor 1 Circuit. P0601 - Internal Memory Checksum Invalid. B1040-64 - Operational Mode Status Info 1 - Signal Plausibility Failure. Customers may experience one or more of the following:Adaptive cruise is inoperative. Remote start is inoperative.

Otherwise, a connector repair kit might be a better option by checking availability on the Mopar connector repair kit website: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE Please send images of any damaged connectors along with a VIN and reason why the harness is needed before replacement to FCA Redacted Content. If no response in 15 minutes, proceed with repair.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0325 - Knock Sensor 1 Circuit. When decelerating DTC P0325 can be set and stays on. P0601 - Internal Memory Checksum Invalid. B1040-64 - Operational Mode Status Info 1 - Signal Plausibility Failure. Customers may comment one or more of the following: Adaptive cruise is inoperative. Remote start is inoperative.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0325 - Knock Sensor 1 Circuit. P0601 - Internal Memory Checksum Invalid. B1040-64 - Operational Mode Status Info 1 - Signal Plausibility Failure. Customers may experience one or more of the following:Adaptive cruise is inoperative. Remote start is inoperative.

Otherwise, a connector repair kit might be a better option by checking availability on the Mopar connector repair kit website: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE Please send images of any damaged connectors along with a VIN and reason why the harness is needed before replacement to FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0325 - Knock Sensor 1 Circuit. P0601 - Internal Memory Checksum Invalid. B1040-64 - Operational Mode Status Info 1 - Signal Plausibility Failure. Customers may experience one or more of the following:Adaptive cruise is inoperative. Remote start is inoperative.

Otherwise, a connector repair kit might be a better option by checking availability on the Mopar connector repair kit website: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE Please send images of any damaged connectors along with a VIN and reason why the harness is needed before replacement to FCA Redacted Content. If no response in 15 minutes, proceed with repair.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when

Engineering has updated the skirt height of the valve cover to address oil leaks. Replace the valve cover (part # 04893800AI (right side) or 04893799AH (left side)includes valve cover gasket) to ensure proper repair. Please call FCA Redacted Content to facilitate fast track shipment of failed part.

EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flexplate found broken on vehicles> 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on transbell housing are oblong, send pictures toFCA Redacted Content. 2) Call FCA Redacted Content, if no oblongholes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacted Content.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE, AND MUST BE REPLACED, AND PROPERLY TORQUED TO 105 NM. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA, Fastener Service Kit PN 68329056AA. Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA For vehicle noise and flexplate found broken on vehicles> 50K miles. 1)Verify and Take pictures of the Trans/engine dowel pin holes, to see if the holes on transbell housing are oblong, send pictures to FCA Redacted Content. 2) Call FCA Redacted Content, if no oblongholes are found to arrange trans swap and fast track the trans back to QEC. If vehicle won?t move and has noise/leaking from transmission bell housing area, check transmission pump bushing. If pump bushing is scored or damaged, replace the pump assembly as opposed to transmission. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. When replacing the long block engine, the VVT Actuator's PN 05184101A* must also be replaced. Engineering is requesting additional information when the long block engine is replaced due to thrust washer failures. Contact FCA Redacyed Content.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

may later return for an oil leak. Engineering has updated the skirt height of the valve cover to address oil leaks. Replace the valve cover (part # 04893800AI includes valve cover gasket) to ensure proper repair. Please call FCA Redacted Content if further questions or help is needed with parts retention returns on valve cover assemblies

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Maps not loading on the Instrument Panel Cluster (IPC) display. Cannot change satellite stations, display shows one station on screen but is playing another. Battery drain. A Black screen after clicking accept at start up (Rearview camera functions normally). Radio resets (Rearview camera functions normally). Wireless connectivity disconnecting. CarPlay icon does not appear in device manager. Audio disruptions. SXMT inoperative. Audio mute. Passenger screen blank. Passenger screen apps missing. Missing profiles icon. IPC displays incorrect audio source. Radio is slow to respond. Trailer tire pressure configurations deleted. Steering wheel controls skipping SXMT channels. Recent calls not displayed. Phone audio playing when ignition is off. In addition, the following software enhancement(s) are available: Icon size/layout improvements. Carplay/Android Auto improvements. Uconnect Phone improvements. FOTA improvements. Passenger screen camera app improvements. Voice Recognition (VR) command improvements. This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from T25.48 or T25.51 to T27.46."

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Yellow Key Light and Message Service Passive Entry Vehicle Will Not Shut Off or Restart To Shut Off Vehicle See Vehicle Settings Displayed in Cluster

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

following: ? **Blank screen (Rear view camera is not affected and will still function normally).** ? Battery drain. ? Radio resets (Rear view camera will still function normally). ? Wireless connectivity device disconnect. ? CarPlayT icon does not appear in device manager. ? Climate icon missing. ? Audio disruptions. ? SXMT inoperative. ? Audio muted. ? Passenger screen blank. ? Passenger screen apps missing. ? Missing profiles icon. ? Instrument Panel Cluster (IPC) displays incorrect audio source. ? Radio is slow to respond. ? Trailer tire pressure configurations deleted. ? Steering wheel controls skipping SXMT channels. ? Recent calls not displayed. ? Phone audio playing with ignition off. The following improvements are also included with this update: ? Apple CarPlayT and Android AutoT improvements. ? Voice Recognition (VR) command improvements. ? Uconnect phone improvements. ? FOTA improvements. ? Passenger screen camera app improvements. ? Icon size/layout improvements. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S24.13 or S24.18 to S26.17. NOTE: The national launch for the FOTA is expected to begin November 25, 2022.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

camera is not affected and will still function normally). ? Battery drain. ? Radio resets (Rear view camera will still function normally). ? Wireless connectivity device disconnect. ? CarPlayT icon does not appear in device manager. ? Climate icon missing. ? Audio disruptions. ? SXMT inoperative. ? Audio muted. ? Passenger screen blank. ? Passenger screen apps missing. ? Missing profiles icon. ? Instrument Panel Cluster (IPC) displays incorrect audio source. ? Radio is slow to respond. ? Trailer tire pressure configurations deleted. ? Steering wheel controls skipping SXMT channels. ? Recent calls not displayed. ? Phone audio playing with ignition off. ? SXM radio application missing (North America Only). ? Navigation screen is blank. ? Media page screen is frozen. ? With forward camera, ?Check Entire Surroundings? verbiage is

camera is not affected and will still function normally). ? Battery drain. ? Radio resets (Rear view camera will still function normally). ? Wireless connectivity device disconnect. ? CarPlayT icon does not appear in device manager. ? Climate icon missing. ? Audio disruptions. ? SXMT inoperative. ? Audio muted. ? Passenger screen blank. ? Passenger screen apps missing. ? Missing profiles icon. ? Instrument Panel Cluster (IPC) displays incorrect audio source. ? Radio is slow to respond. ? Trailer tire pressure configurations deleted. ? Steering wheel controls skipping SXMT channels. ? Recent calls not displayed. ? Phone audio playing with ignition off.** ? SXM radio application missing (North America Only). ? Navigation screen is blank. ? Media page screen is frozen. ? With forward camera, ?Check Entire Surroundings? verbiage is covering other buttons. ? Weather images are oversized. ? SXM 360L / Internet stations not available. **The following improvements are also included with this update: ? Apple CarPlayT and Android AutoT improvements. ? Voice Recognition (VR) command improvements. ? Uconnect phone improvements. ? FOTA improvements. ? Passenger screen camera app improvements. ? Icon size/layout improvements.** This bulletin involves inspecting the software level and updating the software to S26.17.

following: ? **Blank screen (Rear view camera is not affected and will still function normally).** ? Battery drain. ? Radio resets (Rear view camera will still function normally). ? Wireless connectivity device disconnect. ? CarPlayT icon does not appear in device manager. ? Climate icon missing. ? Audio disruptions. ? SXMT inoperative. ? Audio muted. ? Passenger screen blank. ? Passenger screen apps missing. ? Missing profiles icon. ? Instrument Panel Cluster (IPC) displays incorrect audio source. ? Radio is slow to respond. ? Trailer tire pressure configurations deleted. ? Steering wheel controls skipping SXMT channels. ? Recent calls not displayed. ? Phone audio playing with ignition off. The following improvements are also included with this update: ? Apple CarPlayT and Android AutoT improvements. ? Voice Recognition (VR) command improvements. ? Uconnect phone improvements. ? FOTA improvements. ? Passenger screen camera app improvements. ? Icon size/layout improvements. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S24.13 or S24.18 to S26.17. NOTE: The national launch for the FOTA is expected to begin November 25, 2022.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0601 - Internal Memory Checksum Invalid. B1040-64 - Operational Mode Status Info 1 - Signal Plausibility Failure. Customers may experience one or more of the following: Adaptive cruise is inoperative. Remote start is inoperative.

Tire Pressure Sensors Values Are Not Displayed

Yellow Key Light And Message ?Service Passive Entry Vehicle Will Not Shut Off Or Restart? ?To Shut Off Vehicle See Vehicle Settings? Displayed In Cluster

regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. National launch for this FOTA update is expected on: Current Level 5.11.0 update to 5.20.2, Estimated launch date of 10/7/22. Customers may experience the following: All data App and remote operations feature are missing.

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

A missing security certificate or after a new TBM installed, or any active DTC set by TBM will trigger this popup. Please refer to STAR Online S2108000015 for more information. If you continually see this popup message, also see an active B22A9-93 DTC, please use wiTECH tool to check TBM2 module and record the failure information as shown on STAR Online S228A000003. Before replacing the TBM module, please check connections behind the TBM, the antenna and harness for improper connection and damage. Please call FCA Redacted Content

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

A missing security certificate or after a new TBM installed, or any active DTC set by TBM will trigger this popup. Please refer to STAR Online S2108000015 for more information. If you continually see this popup message, also see an active B22A9-93 DTC, please use wiTECH tool to check TBM2 module and record the failure information as shown on STAR Online S228A000003. Before replacing the TBM module, please check connections behind the TBM, the antenna and harness for improper connection and damage. Please call FCA Redacted Content

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set: P0601 - Internal Memory Checksum Invalid. B1040-64 - Operational Mode Status Info 1 - Signal Plausibility Failure. Customers may experience one or more of the following: Adaptive cruise is inoperative. Remote start is inoperative.

Tire Pressure Sensors Values Are Not Displayed

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC) has been set: P0031 - O2 Sensor 1/1 Heater Circuit Low.

information.

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.

Customers may describe one or more of the following: Connected features are inoperable. Radio not receiving Firmware Over The Air (FOTA) updates.

(FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S23.13 to S24.13The national launch for the FOTA is expected to begin June 11, 2022. Customers may experience one or more of the following: No Verbal warnings on navigation. Audio Overlap between sources. Radio doesn?t recognize the vehicle is in park. No keyboard pop up, vehicles setting are hidden. Radio presets are not saving. Audio mute on calls (Phone, SOS and Ecall). Radio resets. Radio screen freezes.The rear view camera display, will work properly if the radio display screen freezes. Audio disruptions. Unable to connect compatible wireless connectivity device. Wireless connectivity disconnecting. Improvements are included with this update:Apple CarPlay and Android Auto improvements. Voice Recognition improvements. Uconnect Phone improvements.

this is normal and not a defect.

be denied.

C0604- Active Air Dam Control Performance

semi and full synthetic oils.

KIT W/O H,BUCKET SEAT PLASTIC KIT W/H,PLASTIC COVER INTERIOR SIDE DRIVER,PLASTIC COVER INTERIOR SIDE BENCH SEAT The following plastic covers are no longer included with the seat assemblies -FRONTAL PLASTIC GRILL FOR PASSENGER BENCH SEAT PN 1ZU08JXWA$ -DRIVER BUCKET SEAT INTERNAL PLASTIC SIDE COVERS PN 1ZU38JXWA$ -PASSENGER BUCKET SEATS INTERNAL PLASTIC SIDE COVERS PN 1ZU15JXWA$

This bulletin involves replacing the windshield.

longer included in the original vehicle build. Warranty claims for shortage and error will be subject to change back.

Technician observed no Diagnostic Trouble Codes (DTCs) however the rear doors are not unlocking.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

The customer may notice a noise from the rear cargo area.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

B)

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

"

Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.

No further parts distribution will be taking place. All distributed parts would cover all sold and unsold needs. Please use all stock that your dealer has before asking for parts assistance. If part assistance is still required, please provide the following information to your Area Manager for review: 1. Dealer Code 2. Last eight digits of VIN 3. Appointment date/vehicle VOR at dealer Thank you, Mopar

function is inoperative, or the SAT channel shows the message: "Satellite Antenna Unavailable/Satellite Signal Failure". ? After failed attempt retry screen, Head Unit (HU) doesn?t reconnect to CarPlay?. ? After a sleep (Key Off/On), stored DTC U1176-00, Lost Communication with Emergency Alert Module. ? At key-on the HU turns on even if Auto-On Radio is off. ? DTC randomly present in error memory: DTC B14DB-13 - USB TBM Port - Circuit Open, randomly. ? At radio startup, the customer can see the "Accept" button on the disclaimer being shown without capital letter. ? Buttons and text are smaller in "Controls" Tab. ? The rejection tone is not played when an empty preset is selected. ? The preset bar in the media screen, starts with the last position preset instead of first. ? For an instant the screen phone appears during the activation of an error pop-up in power off condition. ? DND (Do Not Disturb) check mark blinks. ? The profiles icon in status bar does not updated after the user changes the driver profile. ? Radio screen display changes the home screen when the radio is turned off and back on. Radio should stay on the last screen selected. The radio has not switched to the category bar section. ? The "Remind me later/never show again" popup graphics are wrong, the buttons are almost taking the whole space of the popup. ? When scrolling the Contacts list, a letter pop-up will display as an overlay so user can?t see which letter of list they are scrolling though as they scroll up or down. ? When entering the Settings list or sub-lists the customer is not always brought back to the previous position in the list. ? When accessing settings about Brakes section within Vehicle tab, the customer is not informed 0about non availability of the feature while vehicle is in motion. ? When the customer is adding a new

the following: ? Radio satellite function is inoperative, or the SAT channel shows the message: Satellite Antenna Unavailable/Satellite Signal Failure. ? After failed attempt retry screen, Head Unit (HU) doesn?t reconnect to CarPlay?. ? After a sleep (Key Off/On), stored DTC D176, lost communication problem with Telematics Box module (TBM). ? At key-on the Head Unit (HU) turns on even if Auto-On Radio is off. ? DTC randomly present in error memory: DTC B14DB-13-USB TBM PORT - CIRCUIT OPEN randomly present. ? At radio startup, the customer can see the Accept button on the disclaimer being shown without capital letter. ? Buttons and text are smaller in Controls Tab. ? The rejection tone is not played when an empty preset is selected. ? The preset bar in the media screen, starts with the last position preset instead of first. ? For an instant the screen phone appears during the activation of an error pop-up in power off condition. ? DND (Do Not Disturb) check mark blinks. ? The profiles icon in status bar does not updated after the user changes the driver profile. ? The user turns on the vehicle and sees the focus is on vehicle screen, then turns off the radio. they turn on the radio again and he sees the radio switched from vehicle to Home section. ? The Remind me later/never show again popup graphics are wrong, the buttons are almost taking the whole space of the popup. ? When scrolling the Contacts list, a letter pop-up will display as an overlay so user can?t see which letter of list they are scrolling though as they scroll up or down. ? When entering the Settings list or sub-lists the customer is not always brought back to the previous position in the list. ? When accessing settings about Brakes section within Vehicle tab, the customer is not informed about non availability of the feature while vehicle is in

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order a "68" part number for New unsold units only.

PRIOR TO PERFORMING ANY THERMOSTAT REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2309000014

Library for specifications so a suitable alternative can be used

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. Customers may also comment on the following: Transmission randomly shifts into neutral gear while driving. NOTE: The vehicle can be reset with an ignition/key cycle from Off and then back to Start to allow the vehicle to shift normally. This bulletin involves reprogramming the TCM with the latest available software."