2018 Ram Promaster City TSBs

pressure low indicator lamp illumination between oil changes. Excessive oil consumption This bulletin involves performing an oil consumption verification test and possibly replacing the long block. "

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block."

pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

installed in the vehicle.

oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

E)

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

(Note: ETL, ETK, ETM, ETN Diesel Engines)

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

vent pipe, battery vent cap and clamps. A customer or technician may notice one or more of the following:Battery acid dripping on the transmission pan from the battery tray drain pipe being too short. Battery acid residue present on and around the sides of the battery(technician to verify with litmus paper test). Leak at the valve body cover pan caused by battery acid leaking on it.

vent pipe, battery vent cap and clamps. A customer or technician may notice one or more of the following:Battery acid dripping on the transmission pan from the battery tray drain pipe being too short. Battery acid residue present on and around the sides of the battery(technician to verify with litmus paper test). Leak at the valve body cover pan caused by battery acid leaking on it.

Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.

stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

&Rear Door

Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.

Before replacing the blower motor please call one of these individuals:~ First call Brad Bartkowicz at cell (586) 808-4114~ If no answer, then call Vince Celli at cell (586) 630-8136~ If not response in 15 minutes, continue with repair.

Before replacing any of the part numbers listed above, please call any of the following people for each vehicle type. (If you don't get an answer within 15 minutes,then proceed with the repair.):~ WD/WK--68224166AB - Front Ken Deneau, cell (248)-765-0288~ 68089094AA - Rear Pat Presti- cell (248) 379-0972~ KL/UF/PF- 68223053AB, 68225055AA Mark Ware, cell (248) 705-3469~ F500- 68093422AB,Matt Sasina, cell (248)-464-4982 or Bryan Bremer cell (248) 429-9014~ RT- 68029719AB - Front, Matt Filipkowski cell (248) 877-9106~ 05183147AA - Rear, Ken Deneau, cell (248)-765-0288

Engineering would like to have both parts returned for analysis. Also, please take a picture of the parts and email the picture, a short discription of the issue, and the last 8 digits of the VIN to Brigitte.Wicks@fcagroup.com. Thank you.

Before replacing the compressor call FCA Release Engineer Mark Briolat at cell (248) 345-0127. If no response in 15 minutes, continue with the repair.

intermittent by driving under heavy throttle will produce a C1494-92 DTC, if yes, please call FCA axle engineering and do not replace the PTU. Bruce Michel at cell (248) 260-8641, or Jian Zhu at cell (248) 379- 1132. If neither answers with 15 minutes then proceed with the repair. ~ If the service 4WD light lamp is on steady then replace the Power Transfer Unit.

information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com

Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data.

If the power steering pump is being replaced because the power steering fluid flow or pressure readings are below specification, the power steering fluid reservoir and cap assembly should also be replaced. Power steering reservoir and cap assembly 52126151AG or later should be used.

or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com

stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

Suspect stock of part number: 04627694AAmust be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before17 April, 2017.

contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Customer may experience one or more of the following: A warning on the Electronic Vehicle Information Center (EVIC) stating that the running lights are out. Further inspection reveals all lights are functional. Battery state of charge may be low.

Customer may experience the following:A warning on the Electronic Vehicle Information Center (EVIC) stating that the running lights are out. Further inspection reveals all lights are functional. Battery state of charge may be low.

If no response in 15 minutes, proceed with repair.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68260866AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 68085880AD, 68085880AF, 68085881AE, 68085881AF, 68085881AG. Replacement part numbers are: 68085880AG, and 68085881AH. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

are receiving this email as you have been identified to have stock on hand or have stock in transit to your dealership. Reports of dealers receiving incorrect fuel pressure sensors packaged as 68210332AA. Correct and suspect parts can be identified visually by the color of the label on the sensors. Correct sensors have white color label on the part whereas the suspect sensors have yellow colored labels. Reference pictures attached for visual identification. Please inspect stock on hand and return any suspect parts found back to your facing PDC using MRA code 02. Replacement parts can be obtained by reordering the same part number. Direct all questions via email to vn83@chrysler.com

The radio should not be replaced for this issue if the fault is stored, if the code cannot be reproduced and no trouble can be found (radio functions properly). In this case it is no impact to the customer in any way. Do NOT replace the radio for this issue. Please contact John Carlesimo at cell (248) 941-8756 if you have any further questions regarding this fault.

contact Michael Wang at cell (248) 701-5351. If no response or contact is made within 15 minutes, proceed with repairs as necessary.

Please identify battery with the last 8 VIN digits along with the 15 digit Medtronic code from the GR-8 tester. If no response in 15 minutes, continue with the repair. Battery needs to be held and not turned in for core charges.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:

have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016.

Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

this is normal and not a defect.

semi and full synthetic oils.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

MasterShield Products in stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers: 82212074, 82212075, 82212076, 82212077, 82212078, & 82213598 . Please return suspect parts back to your facing depot using Return Code 02, before 18 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all suspect stock of following part number: 05026886AJ. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 02 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

If no response is received within 15 minutes, then proceed with required repair.

Call Mike Wicker at cell (248) 821- 9350 with the Fault Code, so we can determine true root cause. If your call is not returned within 15 minutes, please continue with the repair

covers and seat cover repairs.

Please return all stock of part number 68288760AA. Replacement part number is 68288760AB. Replacement parts w ill be available w eek ending 5/6/16. Please return suspect parts back to your facing depot using Return Code 02, before 26 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 68003062AB, 68003083AB, 68003085AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 1PE001W 7AB, 1PE011W 7AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

As per regulatory compliance: Please return follow ing stock of part numbers: 82214711, 82214712, 82214713, 82214714, 82214715, 82214716, 82214717, 82214718, 82214720, 82214721, 82214722, 82214723, 82214724, 82214725, 82214726, 82214727, 82214728, 82214729, 82214730, 82214731, 82214732. Please return parts back to your facing depot using Return Code 02, before 31May, 2016.

Please return suspect stock of following part numbers: 68050625AA, 68050626AA, 68050627AA, 68050628AA, 68050743AA, 68050744AA, 68050839AA, 68050841AA, 68257133AA, 68257134AA, 68264578AA, 68264579AA, 68264580AA, 68264581AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 April, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return parts which have a pacakging date code of July 20th 2016. Reference pictures attached for suspect part identification. Please return parts backto your facing depot using Return Code 02, before 31 August, 2016.

Please return suspect stock of part number 68143886AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 68174065AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 68141880AH, 68141881AH, 68145625AI, 68145626AI, 68189480AF and replacement part numbers are 68141880AI, 68141881AI, 68145625AJ, 68145626AJ & 68189480AG respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 05278632AF and replacement part number is 52030379AA which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 1YG06JSCAC, 1YG06KEPAC, 1YG 06KFSAC, 1YG 06KGZAC, 1YG 06KBUAC and replacement part numbers are 1YG 1YG06KFSAD, 1YG 06KG ZAD, 1YG 06KBUAE respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 68188889AE and replacement part number is 68188889AF which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of following part numbers: 68036213AA, 68036230AF, 68158196AC, 68158197AD, & 68158454AD. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allstock of following part numbers:68241568AB,68241568AC,68241569AB,68241569AC, 68241570AB,68241571A.Replacement part numbersare 68241568AD,68241569AD,68241570AD,68241571AD, which are in stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

This same month last year we had over 40,000 open aged > 5 days tickets. As a result of focused efforts to verify vehicles are repaired and close tickets the number is now at just under 7,000 tickets.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 05182600AC. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock,or have stock in transit to your dealership. Please return all suspect stock of following part numbers:68159725AB,& 68261143AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02,before 27 O ctober,2015. Return any open orders in process too. Direct all questions via email to MO PARQ C@fcagroup.com

LT:04805839AD

To do this, add the LEG (Trailer Tow Mirrors) sales code to the VIN using DealerCONNECT and then performing a vehicle re-configuration using the WiTech tool.~ After Kit is completely installed, perform the following;~ 1. Add LEG sales code to the VIN under the ?Vehicle Option Updates? Found on Dealerconnect~ 2. Update Vehicle Configuration by using the WiTech tool and performing ?Restore Vehicle Configuration.?

stock in transit to your dealership. Please return suspect stock of part number 68160775AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 26 August, 2016.

A)

Please return allsuspect stock of part numbers:68212041AC,68141170AC,55112738AA.See attachmentsfor identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Please return all suspect stock of following part numbers: 57010364AI, 57010365AI, 57010504AJ, 57010505AJ, 68224368AB, 68224369AB. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017.

numbers:55395241AG,55395241AE.Replacement ispart number 55395241AH which isin stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 12April,2017

have stock in transit to your dealership. Please return suspect stock of part number 04589131AG, 04589243AG . See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 7 April, 2016.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 68146401AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock, or have stock in transit to your dealership. Please return following part numbers: CBTTP57FAA, & CBTTP57FAB. Replacement part number CBTTP57FAC will be available week beginning 26 O ct., 2015. There are reports of pre-programmed FO BS in these kits, preventing dealer pairing of W IN and Transmitter Key FO BS. If repair is needed prior to new part availability, order two of part number 05026886AK transmitter Integrated Key FO B. Please return suspect parts back to your facing depot using Return Code 02, before 06 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

(248) 622 8109 ~ Mexican Dealers please call Ricardo Lozada at cell +52 1 55 1370 3187. If no return call in 15 minutes, continue with repair.

please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair.

A customer may experience one or more of the following conditions: Radio display screen will lock up and reset intermittently. Incorrect routing directions to fuel stations when using Travel Link. Unable to turn on heated seats; icon is greyed out. Navigation screen goes blank. Navigation system freezes/locks up. Vehicles with Mopar special edition radio will update radio?s splash screen. Navigation icon shows the vehicle going backward when it?s moving forward.

stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allsuspect stock of part numbers:68148794AH,68148794AF,68148794AD,68156453AH,68156453AF, 68156453AD,68161542AE,68161542AD.See attachment for identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Library for specifications so a suitable alternative can be used

A test-drive snap shot may help you isolate the source of the issue.

Start Date: 10/27/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of part numbers: 68144663AA, 52013874AE. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to MOPARQC@fcagroup.com

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any DTCs identified with the scan tool and document them on the repair order.

check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.

Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Please return stock of part number 68103256AG packaged before 2016/08/01. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

industry awareness regarding the use of recycled or salvage parts.

Please return suspect stock of following part numbers: 68110016AC, 68110016AD, 68110016AE, 68110017AD, 68236104AC, 68236105AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31 August, 2016.

as either having stock, or have stock in transit to your dealership. Please return all suspect stock of follow ing part number: 68245351AB. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please send video to the following e-mail address: Darren.Pontin@fcagroup.com. Please reference Service Library for the latest Diagnostics.

If no response in 15 minutes, proceed with ordering the part

spare tire winch cable when storing under the vehicle. The adapter is part number 6824863AA and requires three (3) mounting nuts; PN 68150129AA.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

B)