2019 Ram 5500 TSBs

New Part: 68645327AA (Non-Oiled Air Filter) Replaces: 53034051AA (Oiled Air Filter) - This part is superseded and should no longer be installed. The air filter for all other applications remains unchanged: Continue to use 68517554AA for: All 2018 MY and older 6.7L Cummins equipped vehicles. All 2019 MY and newer vehicles with non-6.7L engines. 2. Special Service Procedure for DTC P0299 Application: 2019-2024 MY HD Trucks with 6.7L Diesel (ETM/ETN) Condition: If DTC P0299 is active and the vehicle is equipped with the previous oiled air filter (PN# 53034051AA). Procedure: Replace the oiled air filter (53034051AA) with the new non-oiled filter (68645327AA). Service Catalog reflects these updated usages.

Clicking noise. Engine noise.

In these situations, it is recommended to use the appropriate Mopar air filter (57008652AA). The "AC" level of the part is in development to resolve this issue. 1BP00507AB should still be usable for 2018 and older Model year Cummins engines.

please reference SOL Case #S2508000062 prior to replacement of Transfer Case shift motor.

Or Corrupted

the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. Not following the proper DEF fill procedure and overfilling the tank This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software This bulletin involves replacing the urea delivery module and possibly updating the Dosing Control Unit (DCU) software"

and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC):** P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. Not following the proper DEF fill procedure and overfilling the tank.** This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software."

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0506-00 - Idle Control System RPM - Lower Than Expected. P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P0299-00 - Turbocharger Underboost. P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - ETC Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambient temperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P203F - Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambient temperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performance.

Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration

Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P1404 - EGR Close Position Performance. ? P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. In addition, the customer may notice one or more of the following conditions: ? **Power Take Off (PTO) disable to high engine oil temperature (DD DP Only).** ? Abrupt gear engagement when transitioning from Park to Drive/Reverse gear state in Power Takeoff (PTO) Mode. ? Vehicle hesitation or surge at low vehicle speeds. ? Engine hesitation when turning steering wheel to end stop. ? Powertrain bump or hesitation around 16-24 kph (10-15 mph) vehicle speed. May be reported as rough or harsh transmission shifting in the same vehicle speed range This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software.

Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration

The customer may notice one or more of the following: When decelerating from a 1 to 2 gear shift, the vehicle may have a harshshift. From a 1 to 2 gear change there may be a perceived bump feeling, whilehaving a light pedal(Sales Codes ETL and ETN Only). A harsh shift from a 2 to 3 gear shift while at almost or wide openthrottle. A harsh shift from a 3 to 4 shift and heavy on the pedal, lifting offthe pedal, then back on the pedal again. While coasting down a grade, an abrupt deceleration may be felt. A clunk heard when shifting from park to reverse or drive. Cold engine flare during a shift. A delay when coasting down, vehicle is in a downshift at low speedsand then trying to accelerate. (The vehicle will have a hesitation as the vehicle tries to change gears to accommodate the new pedaldemand). Excessive shifting(DD and DP Only). Engine flare caused by the transmission releasing the clutch too early duringa 1 to 2 shift. Poor shift quality. Shift or gear hunting. A harsh 2-1 shift. Hesitation in up-shifts and/or down-shifts. Shudder and/or clunk when shifting into gear. The following software enhancements are available:Stored faults can only be cleared by a diagnostic scan tool, this softwarewill allow the TCM to self clear. 2-1 coast down-shift improvements. 1-2/2-3/3-4/4-5 and 5-6 shift improvements.

Diagnostic Trouble Codes (DTCs) P061B ? Internal Control Module Torque Performance, And/Or P064B ? PTO Control Module, Set.

installed in the vehicle.

G)

Diagnostic Trouble Codes (DTCs) P061B ? Internal Control Module Torque Performance, And/Or P064B ? PTO Control Module, Set.

J)

Or Corrupted

to an oil leak, do NOT remove the seal from the retainer. Replace the seal and retainer (pn# 05086755A$) as a complete unit. Engineering needs to obtain the seals and retainers back for analysis without them having been disassembled. Once repairs are complete, please contact FCA Redacted Content to return the parts.

Module/Powertrain ControlModule (ECM/PCM) with the latest available software.

I)

When performing diagnosis, an internal engine concern may be suspected.

J)

to an oil leak, do NOT remove the seal from the retainer. Replace the seal and retainer (pn# 05086755A$) as a complete unit. Engineering needs to obtain the seals and retainers back for analysis without them having been disassembled. Once repairs are complete, please contact FCA Redacted Content to return the parts.

J)

to an oil leak, do NOT remove the seal from the retainer. Replace the seal and retainer (pn# 05086755A$) as a complete unit. Engineering needs to obtain the seals and retainers back for analysis without them having been disassembled. Once repairs are complete, please contact FCA Redacted Content to return the parts.

F)

Or Corrupted

The customer may notice one or more of the following: When decelerating from a 1 to 2 gear shift, the vehicle may have a harshshift. From a 1 to 2 gear change there may be a perceived bump feeling, whilehaving a light pedal(Sales Codes ETL and ETN Only). A harsh shift from a 2 to 3 gear shift while at almost or wide openthrottle. A harsh shift from a 3 to 4 shift and heavy on the pedal, lifting offthe pedal, then back on the pedal again. While coasting down a grade, an abrupt deceleration may be felt. A clunk heard when shifting from park to reverse or drive. Cold engine flare during a shift. A delay when coasting down, vehicle is in a downshift at low speedsand then trying to accelerate. (The vehicle will have a hesitation as the vehicle tries to change gears to accommodate the new pedaldemand). Excessive shifting(DD and DP Only). Engine flare caused by the transmission releasing the clutch too early duringa 1 to 2 shift. Poor shift quality. Shift or gear hunting. A harsh 2-1 shift. Hesitation in up-shifts and/or down-shifts. Shudder and/or clunk when shifting into gear. The following software enhancements are available:Stored faults can only be cleared by a diagnostic scan tool, this softwarewill allow the TCM to self clear. 2-1 coast down-shift improvements. 1-2/2-3/3-4/4-5 and 5-6 shift improvements.

E)

(ETL, ETM, ETN Engines)

Diagnostic Trouble Codes (DTCs) P061B ? Internal Control Module Torque Performance, And/Or P064B ? PTO Control Module, Set.

Module/Powertrain ControlModule (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P0506-00 - Idle Control System Rpm - Lower Than Expected. P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam only). P0302-00 - Cylinder 2 Misfire(Sym Cam only). P0303-00 Cylinder 3 Misfire(Sym Cam only). P0304-00 - Cylinder 4 Misfire(Sym Cam only). P0305-00 - Cylinder 5 Misfire(Sym Cam only). P0306-00 - Cylinder 6 Misfire(Sym Cam only). P0299-00 - Turbocharger Underboost. P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambienttemperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambienttemperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performan

I)

regarding the identification differences in the high pressure fuel injection pumps between the new style Symetrical Cam design pump and the old syle Asymetrical Cam design used on the 6.7L Cummins in the 2019 and 2020 HD Trucks. The following information is intended to eliminate confusion and possible noise complaints shortly after pump replacement or ECM reprogramming.

Failure to program the ECM with the correct calibration after installation of this pump will create an undesireable noise characteristic from the pump. Please be sure to follow all normally published Service Bulletins, and Service Information for the latest installation instructions, and programming steps.

installed in the vehicle.

53034051A$ For all 2018 MY and older 6.7L Cummins equipped vehicles,and2019 MY and newer non 6.7L equipped vehicles, please use pn# 68517554A$ Service Catalog reflects these usages.

Also fuel system cleaning and fuel system kit replacement. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0087-00 - Fuel Rail Pressure Too Low. P008A-00 - Low Pressure Fuel System Pressure - Too Low. P0201-00 - Fuel Injector 1 Circuit/Open. P0202-00 - Fuel Injector 2 Circuit/Open. P0203-00 - Fuel Injector 3 Circuit/Open. P0204-00 - Fuel Injector 4 Circuit/Open. P0205-00 - Fuel Injector 5 Circuit/Open. P0206-00 - Fuel Injector 6 Circuit/Open. The customer may also notice the following:Engine will not start.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Module/Powertrain ControlModule (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P0506-00 - Idle Control System Rpm - Lower Than Expected. P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam only). P0302-00 - Cylinder 2 Misfire(Sym Cam only). P0303-00 Cylinder 3 Misfire(Sym Cam only). P0304-00 - Cylinder 4 Misfire(Sym Cam only). P0305-00 - Cylinder 5 Misfire(Sym Cam only). P0306-00 - Cylinder 6 Misfire(Sym Cam only). P0299-00 - Turbocharger Underboost. P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambienttemperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambienttemperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performan

I)

Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam only). P0302-00 - Cylinder 2 Misfire(Sym Cam only). P0303-00 - Cylinder 3 Misfire(Sym Cam only). P0304-00 - Cylinder 4 Misfire(Sym Cam only). P0305-00 - Cylinder 5 Misfire(Sym Cam only). P0306-00 - Cylinder 6 Misfire(Sym Cam only). P0299-00 - Turbocharger Underboost. P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambient temperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambient temperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performance. The customer may also notice one or more of the following:Harsh downshift clunk during

B)

Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam only). P0302-00 - Cylinder 2 Misfire(Sym Cam only). P0303-00 - Cylinder 3 Misfire(Sym Cam only). P0304-00 - Cylinder 4 Misfire(Sym Cam only). P0305-00 - Cylinder 5 Misfire(Sym Cam only). P0306-00 - Cylinder 6 Misfire(Sym Cam only). P0299-00 - Turbocharger Underboost. P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambient temperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambient temperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performance.

regarding the identification differences between the CP4 style high-pressure fuel injection pump, and the new CP3.3 style high-pressure fuel injection pumps installed under the Y78 recall. The following information is intended to eliminate confusion and possible noise complaints shortly after pump replacement or ECM reprogramming.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P0506-00 - Idle Control System RPM - Lower Than Expected. P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P0299-00 - Turbocharger Underboost. P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambient temperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambient temperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performance. The customer may also notice one or more of the following: PTO Allows E-Sto

Also fuel system cleaning and fuel system kit replacement. Customers may experience a Malfunction Indicator Lamp MIL illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes DTCs have been set: P0087-00 - Fuel Rail Pressure Too Low. P008A-00 - Low Pressure Fuel System Pressure - Too Low. P0201-00 - Fuel Injector 1 Circuit/Open. P0202-00 - Fuel Injector 2 Circuit/Open. P0203-00 - Fuel Injector 3 Circuit/Open. P0204-00 - Fuel Injector 4 Circuit/Open. P0205-00 - Fuel Injector 5 Circuit/Open. P0206-00 - Fuel Injector 6 Circuit/Open. The customer may also notice the following:Engine will not start.

Module/Powertrain ControlModule (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P0506-00 - Idle Control System Rpm - Lower Than Expected. P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire(Sym Cam only). P0302-00 - Cylinder 2 Misfire(Sym Cam only). P0303-00 Cylinder 3 Misfire(Sym Cam only). P0304-00 - Cylinder 4 Misfire(Sym Cam only). P0305-00 - Cylinder 5 Misfire(Sym Cam only). P0306-00 - Cylinder 6 Misfire(Sym Cam only). P0299-00 - Turbocharger Underboost. P1D73-00 - AGS Performance. P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambienttemperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambienttemperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performan

I)

When performing diagnosis, an internal engine concern may be suspected.

Failure to program the ECM with the correct calibration after installation of this pump will create an undesireable noise characteristic from the pump. Please be sure to follow all normally published Service Bulletins, and Service Information for the latest installation instructions, and programming steps.

(Note: ETL, ETK, ETM, ETN Diesel Engines)

D)

Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambient temperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambient temperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performance. The customer may also notice one or more of the following:Oil life monitor resets after PCM flash. Diesel Exhaust Fluid (DEF) level gauge inaccurate. Message ?Regen in progress will take up to 70 Minutes? remains in Electronic Vehicle Information Center (EVIC) when aborting manual regeneration process. Excessive DEF consumption. Poor idle at times when engaging cab heat feature. In addition, the following enhancements are included:wiTECH Fuel System R

Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambient temperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambient temperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performance. The customer may also notice one or more of the following:Oil life monitor resets after PCM flash. Diesel Exhaust Fluid (DEF) level gauge inaccurate. Message ?Regen in progress will take up to 70 Minutes? remains in Electronic Vehicle Information Center (EVIC) when aborting manual regeneration process. Excessive DEF consumption. Poor idle at times when engaging cab heat feature. In addition, the following enhancements are included:wiTECH Fuel System R

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P2100 - Electronic Throttle Control Motor Circuit/Open - Bank 1. The customer may also describe the following:The vehicle is in limp home mode.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0626 - Generator Field Control Circuit High. P218F - Reductant No Flow Detected. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P0191 - Fuel Rail Pressure Sensor Circuit Performance. P0461 - Fuel Level Sensor 1 Performance. P0401 - EGR System Performance. P20EE - NOx Catalyst Efficiency Below Threshold. P061A - Level 2 Torque Performance. P061B - Internal Control Module Torque Calculation Performance. P061E - Internal Control Module Brake Signal Performance. P062C - Etc Level 2 MPH Performance. P0106 - Manifold Absolute Pressure Sensor Performance (In extreme cold ambient temperatures). P0116 - Engine Coolant Temperature Sensor Performance. P0420 - Catalyst System Efficiency Bank 1. P1507 - Crankcase Filter Restriction. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P203F - (Diesel Exhaust Fluid) Reductant Level Too Low. P226C - Turbocharger Boost Control ?A? Slow Response (In extreme cold ambient temperatures). P2579 - Turbocharger Speed Sensor Circuit. U0101 - Lost Communication with TCM. U02A3 - Lost of Communication with PM Sensor. U3017 - Control Module Timer/Clock Performance. The customer may also notice one or more of the following:Oil life monitor resets after PCM flash. Diesel Exhaust Fluid (DEF) level gauge inaccurate. Message ?Regen in progress will take up to 70 Minutes? remains in Electronic Vehicle Information Center (EVIC) when aborting manual regeneration process. Excessive DEF consumption. Poor idle at times when engaging cab heat feature. In addition, the following enhancements are included:wiTECH Fuel System R

None of the seals from the PTU side will need to be replaced whenever the ATX stubshaftis replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft,it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft-PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.

Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

U11C1-00 (Reductant Control Module Received Implausible Data From ECM/PCM), do not replace the DEF Pump. Follow TSB's released and appropriate Service Diagnostics.

/ DP vehicles with 6.7L (ETL / ETM / ETN) built on or before October 15,2024 and exhibiting DTCs P21C4-00 (Reductant Line Heater Relay Control Circuit High) and / or U11C1-00 (Reductant Control Module received implausible Data from ECM / PCM). These DTCs will occur after installation of service DCU 68458603AB. Do not replace parts until after the TSB 25-008-24 is performed. If the DTC(s) continue to set, then follow the Service Diagnostics for the applicable DTC."

Line Heater Control Circuit High, and U11C1 Reductant Control Module Received Implausible Data From ECM/PCM, Set

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P21C4-00 - Reductant Line Heater Relay Control Circuit High. U11C1-00 - Reductant Control Module Received Implausible Data From ECM/PCM. These DTCs will occur after installation of service DCU 68458603AB. This bulletin involves reprogramming the DCU with the latest available software."

(MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. Not following the proper DEF fill procedure and overfilling the tank. This bulletin involves replacing the urea delivery module and possibly updating the Dosing Control Unit (DCU) software"

(MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. Customers may also experience one or more of the following: Repeated freeze/thaw cycles of the urea tank to cause solid DEF crystals to form and settle on the focus tube, blocking the level sensor signal. Rapid temperature swings from below freezing to above freezing causing an incomplete thaw of the DEF tank. When the vehicle is powered on, the diagnostic is enabled due to thawed DEF at the tank bottom surface, but the fluid in the center is still partially frozen. Not following the proper DEF fill procedure and overfilling the tank. This bulletin involves replacing the urea delivery module and possibly updating the Dosing Control Unit (DCU) software."

Displayed on Cluster

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Diagnostic Trouble Code (DTC) P0607 ? ECU Internal Performance, Set.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thefollowing Diagnostic Trouble Code (DTC) has been set: C15CE-31 - Tire Pressure Sensor 7-No Signal. Customers may also comment on the following: Instrument Panel Cluster (IPC) warning is illuminated for the tire pressure sensors.

Displayed on Cluster

Displayed on Cluster

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

Diagnostic Trouble Code (DTC) P0607 ? ECU Internal Performance, Set.

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Diesel Exhaust Fluid (DEF) issue in extreme cold weather. Diagnostic Trouble Codes (DTCs) P203E - Reductant Level Sensor 1 Circuit Intermittent and/or P203F - Reductant Level Too Low set.

Fuel Injector Circuit Open DTC Additional Diagnostics.

not functioning - If rear camera is not functioning we would expect to see these Diagnostic Trouble Code (DTCs) set by the Central Vision Processing Module (CVPM) - B217A-92 Rear Camera-Performance or Incorrect Operation U0264-00 Lost Communication With Camera Module - Rear 1. Take picture of head unit display so we can verify what part of the image is not functioning (Surround View vs. Rearview Camera) 2. Take vehicle scan and config report so we can verify s/w, DTCs, and vehicle config 3. If rear camera is not functioning, disconnect and reconnect the camera to ensure that the same camera is still not functioning. We want to ensure that the connection at the rear camera is secure. 4. Send information to FCA Redacted Content.

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

Diagnostic Trouble Code (DTC) P0471 ? Exhaust Pressure Sensor 1 Performance, Set.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

the BCM and possibly a radio reset, to enable the auto-on comfort settings. Customers may comment on one or more of the following:If below 4 C (40 F), the heated seats or heated steering wheel turn on by themselves. If above 26 C (80 F), the vented seats turn on by themselves. Cannot turn off the auto-on comfort feature. With the symptom/condition listed above, there?s no setting in the radio to turn the auto-on comfort feature off.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process

latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated to:DT with UAX and UCX - 34.31. All other vehicles and radio combinations - 34.2. The national launch for the FOTA will begin July 21, 2021. Customers may experience one or more of the following: SOS, Automatic SOS (ASOS) , assist calls not showing correct location(DT Vehicles with UAX and UCX Only). GPS inaccuracies(DT Vehicles with UAX or UCX Only). Uconnect radio apps are inoperable(DT Vehicles with UAX or UCX Only). SXM button are greyed out(DT Vehicles with UAX or UCX Only). Intermittently, SXM loading screen is stuck(DT Vehicles with UAX or UCX Only). Uconnect App inoperative(DT Vehicles Only). Voice Recognition (VR) inoperative(DT Vehicles Only). Radio resets(DT Vehicles Only). Radio locks up, freezes or resets. Bluetooth device is slow to pair, or does not pair. GPS unable to load and find locations. Loss of saved radio presets. Display screen is back with no backlighting. No audio output coming from the radio. Cannot control audio volume. Rear view camera display will not turn off.

latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated to:DT with UAX and UCX - 34.31. All other vehicles and radio combinations - 34.2. The national launch for the FOTA will begin July 21, 2021. Customers may experience one or more of the following: SOS, Automatic SOS (ASOS) , assist calls not showing correct location(DT Vehicles with UAX and UCX Only). GPS inaccuracies(DT Vehicles with UAX or UCX Only). Uconnect radio apps are inoperable(DT Vehicles with UAX or UCX Only). SXM button are greyed out(DT Vehicles with UAX or UCX Only). Intermittently, SXM loading screen is stuck(DT Vehicles with UAX or UCX Only). Uconnect App inoperative(DT Vehicles Only). Voice Recognition (VR) inoperative(DT Vehicles Only). Radio resets(DT Vehicles Only). Radio locks up, freezes or resets. Bluetooth device is slow to pair, or does not pair. GPS unable to load and find locations. Loss of saved radio presets. Display screen is back with no backlighting. No audio output coming from the radio. Cannot control audio volume. Rear view camera display will not turn off.

published document)

published document)

latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated to:DT with UAX and UCX - Current software 34.2RM will be update to 34.31FRM. All other vehicles and radio combinations - 34.2. The national launch for the FOTA will begin July 21, 2021. Customers may experience one or more of the following: SOS, Automatic SOS (ASOS) , assist calls not showing correct location(DT Vehicles with UAX and UCX Only). GPS inaccuracies(DT Vehicles with UAX or UCX Only). Uconnect radio apps are inoperable(DT Vehicles with UAX or UCX Only). SXM button are greyed out(DT Vehicles with UAX or UCX Only). Intermittently, SXM loading screen is stuck(DT Vehicles with UAX or UCX Only). Uconnect App inoperative(DT Vehicles Only). Voice Recognition (VR) inoperative(DT Vehicles Only). Radio resets(DT Vehicles Only). Radio locks up, freezes or resets. Bluetooth device is slow to pair, or does not pair. GPS unable to load and find locations. Loss of saved radio presets. Display screen is back with no backlighting. No audio output coming from the radio. Cannot control audio volume. Rear view camera display will not turn off.

Adding Remote Start

This bulletin involves replacing the front driveshaft."

This bulletin involves replacing the front driveshaft."

his bulletin involves replacing the front driveshaft"

Adding Remote Start

this is normal and not a defect.

This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2023 to 2013 HD Trucks. The following information is intended to eliminate confusion.

Additional Diagnostics.

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

semi and full synthetic oils.

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

The customer may describe one or both of the windshield wiper arm are loose and may stop moving at times.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

The customer may describe one or both of the windshield wiper arm are loose and may stop moving at times.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

TPM Lamp On.

Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.

TPM Lamp On.

Diagnostic Trouble Code (DTC) P218F ? Reductant No Flow Detected set.

Disengage

Disengage

Disengage

Diagnostic Trouble Code (DTC) P218F ? Reductant No Flow Detected set.

Disengage

One Or More Heated Seat DTC?s

Diagnostic Trouble Code (DTC) P207F ? Reductant Quality Performance Set.

industry awareness regarding the use of recycled or salvage parts.

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris "

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debri "

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris "

Diesel Exhaust Fluid (DEF) System Diagnostic Trouble Codes (DTCs) due to Hydrocarbon Contamination.

If no response within 15 minutes, proceed with repair

Star Parts Restriction Process

Parts Ordering, And Repair Process Information.

This issue only happens in temperature that are just below freezing and snowing. This bulletin involves removing the right side rubber flaps from the cowl baffles.

to be serviced together when servicing the HVAC housing. Customers may experience the following:Poor Air conditioning system performance (Slow or excess time to cool down). HVAC is slow to cool, left center instrument panel outlet is warmer than right side instrument panel outlets.

system

the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0731-00 - Gear 1 Shift Incorrect Ratio (This DTC will set during a key cycle and shifting into Drive). Customers may also comment on the following: The transmission will not shift into or out of 1st - 4th gears. 5th and reverse gears are still available. **This bulletin involves replacing the K1 clutch and possibly the K1 input shaft drum sub-assembly. These repairs are to be performed only if the vehicle is inoperable due to K1 clutch failure. ** "

Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P0731-00 - Gear 1 Shift Incorrect Ratio (This DTC will set during a key cycle and shifting into Drive). Customers may also comment on the following: ? The transmission will not shift into/or out of 1st - 4th gears. 5th and reverse gears are still available. This bulletin involves replacing the K1 clutch drum snap ring and possibly the K1 input shaft drum subassembly.

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Lost radio presets. ? SXM favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Lost navigation settings. ? SXM icon inoperative (D-Truck). ? Radio display screen is black when the ignition is on (Rear View Camera (RVC) not affected (D-Truck)). ? Radio freeze intermittent (RVC not affected (D-Truck)). ? Wireless connectivity pair or connection issue (D-Truck). ? Radio channel changes by itself (D-Truck). ? Backup camera has black display screen, or Only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) (D-Truck). ? High pitch chime noise (D-Truck). ? Contact list not loading (D-Truck). ? ?Device Not Supported? message (D-Truck). ? Remote app inoperative (D-Truck). ? Travel-Link fuel price incorrect (D-Truck). ? Backup camera gridlines missing (D-Truck). ? Unable to adjust volume (D-Truck). ? Radio may reset/reboots, turn itself off and then back on again (D-Truck). ? High pitch squeal, pop or humming sound coming from all of the speakers (WK RU Only). ? Radio display screen is black, intermittent (RVC not affected (WK RU Only)). ? Radio freeze intermittent (RVC not affected (WK RU Only)). ? Navigation stuck on loading screen or not appearing at all (WK RU Only). ? Radios resets when a wireless connectivity paired phone receives two text messages one after another simultaneously after approximately seven seconds. (ABD sales code). ? Speaker crackling noise on non amplified vehicles (WK RU, UAV Only). ? Active cal

The customer may experience one or more of the following:Poor shift quality. Shift or gear hunting. The 6-4 and 5-3 shift may have a bump. Some 2-3, 3-4 and 4-5 shifts may "flare" when cold. Coastdown bump. The following software enhancement is also available: Stored faults can only be cleared by a diagnostic scan tool, this software will allow the TCM to self clear.

Announces the addition of the Rear AxleAssembly replacementfor 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT)vehicles to the Powertrain Pre-Authorization program to ensure proper repair of Rear AxleAssembly failures and to assist in quality improvements. REV.A

Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program for all dealers (Base, Plus & Premium) to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A

B)

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** **C2200-47 - Anti-Lock Brake Module Internal - Watchdog / Safety Auc Failure.** C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure. Customers may also comment on one or more of the following: **Anti-lock Brake System (ABS) indicator light illuminated in the Instrument Panel Cluster (IPC). Electronic Stability Control (ESC) indicator light illuminated in the IPC. The Red Brake Warning indicator light illuminated in the IPC.** This bulletin involves reprogramming the ABS with the latest software available."

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure.

tensioner and then adjust the parking brake cable system. Customer may comment on one or more of the following:The parking brake foot pedal does not fully return. The red ?brake? light is illuminated in the Instrument Panel Cluster (IPC).

tensioner and then adjust the parking brake cable system. Customer may comment on one or more of the following:The parking brake foot pedal does not fully return. The red ?brake? light is illuminated in the Instrument Panel Cluster (IPC).

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

The customer may notice:Tire Fill Alert or Selectable Tire Fill Alert does not work.

The customer may notice:Tire Fill Alert or Selectable Tire Fill Alert does not work.

"

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

the road surface (symptom is more prevalent in cold temperatures) This bulletin involves replacing the steering damper.

39.6.The repair procedure must be followed step by step. If the radio is not updated with the correct software level at the correct time the radio can be damaged. If the radio was damaged by not following the repairprocedure the radio may need to be replaced. Customers may experience one or more of the following: Lost radio presets. SXM favorite song not displaying/playing. Radio display screen is black, intermittent. Radio freeze intermittent. Incorrect navigation address/location/directions. Bluetooth pair or connection issue. Radio channel changes by itself. SXM icon inoperative. Backup camera has black display screen. High pitch chime noise. Contact list not loading. ?Device Not Supported? message. Remote app inoperative. Travel-Link fuel price incorrect. Backup camera gridlines missing. Unable to adjust volume. In addition the following enhancements are included: Heavy Duty (HD) Truck USB HUB improvements. HD Truck heated steering wheel improvements.