2016 Ram 3500 TSBs

Components are needed by Engineering and Production due to limited availability. To avoid being charged the full replacement value, return within 60 days 68295359AD 68347098AC 68232683AG 68347099AC"

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P1C54 - SCR NOx Catalyst Missing. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P0300 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P218F - Reductant No Flow Detected. U0001-00 - CAN C BUS. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). The following DTCs have been changed from a one trip fault to a two trip fault:P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. In addition to addressing the above DTCs,

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs. P0401 - EGR System Performance. P2281 - Air Leak Between MAF and Throttle Body. P0402 - Egr Flow Excessive Detected. P0234 - Turbocharger Overboost Condition. P049D - Egr Control Position Exceeded Learning Limit. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P064F - Unauthorized Software/Calibration Detected. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P1C54 - SCR NOx Catalyst Missing. P229F -Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P0300 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P218F - Reductant No Flow Detected. U0001-00 - CAN C BUS. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in).

installed in the vehicle.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following DTCs have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: **P0128 - Thermostat Rationality Improvements.** P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy.** Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

Prior to replacing a Power Sliding Backlight Cable Assembly, please contact Marc Galli by cell phone at (248) 941-8402 as he would like to gather information. In addition, if the dealership is within the Metro Detroit Area, Marc would like to analyze the vehicle in person prior to it being repaired. If Marc cannot be contacted within 15 minutes, please provide pictures of the inside lower rail of the glass to confirm (2 passenger side and 1 driver side) cable clips are fully seated as well as pictures of the (2) regulator motor cable spring plungers to confirm they are also seated. Then proceed with the repair. Please email pictures to Marc at marc.galli@fcagroup.com.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault:P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory:P218F - Reductant No Flow Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. U0001-00 - CAN C BUS. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P0128 - Thermostat Rationality Improvements. P2281 - Air Leak Between MAF and Throttle Body. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release:Fuel pressure override test improvement for wiTECH. AC pressure sensor error threshold change. No crank, No start fix. Improvement to correct engine feels like low or reduced power. Engine Noise Improvements Improved Engine Fuel Economy. Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvemen

SCR, please contact Dean Armstrong at (248)-944-5364. Cummins and FCA engineering is currently investigating the root cause to this condition. If you do not receive an answer or call back within 15 minutes, proceed with normal diagnostics

Module/Powertrain Control Module (ECM/PCM) with the latest available software. These DTCs have been changed from a one trip fault to a two trip fault: P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. P207F - Reductant Quality Performance. P218F - Reductant No Flow Detected. U110E - Lost Ambient Temperature Message. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Ambient Air Temperature Improvements. Stationary de-soot with WiTech fix.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. **These DTCs have been changed from a one trip fault to a two trip fault: P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High** A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only).** U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix.** OBD Misfire Monitoring Improvement (68RFE Only).

The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.

Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA, 68046015AA, 68100682AA, 68100676AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair.~ ~___________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A, 05086754A, 05015705A. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~_________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P1C54 - SCR NOx Catalyst Missing. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P0300 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P218F - Reductant No Flow Detected. U0001-00 - CAN C BUS. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). The following DTCs have been changed from a one trip fault to a two trip fault:P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs. P0401 - EGR System Performance. P2281 - Air Leak Between MAF and Throttle Body. P0402 - Egr Flow Excessive Detected. P0234 - Turbocharger Overboost Condition. P049D - Egr Control Position Exceeded Learning Limit. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P064F - Unauthorized Software/Calibration Detected. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P1C54 - SCR NOx Catalyst Missing. P229F -Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P0300 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P218F - Reductant No Flow Detected. U0001-00 - CAN C BUS. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in).

the EGR Cooler is plugged with soot, please contact Stephen Alvarado at the STAR Center at (866) 799-1695 ext. (4720271). Cummins Engineering is currently investigating root cause of this condition. If you do not receive an answer or call back within 15 minutes, proceed with normal diagnostics.

installed in the vehicle.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find oneor more of the following Diagnostic Trouble Codes (DTCs): P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak.

The customer may describe extended cranking or starting times when the Compressed Natural Gas (CNG) tank level is low(DJ only) (Sales Code EZF only).Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation thetechnician may find one or more of the following Diagnostic Trouble Codes (DTCs): P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs.P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P1C54 - SCR NOx Catalyst Missing. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P0300 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0401 - EGR System Performance. P0128 - Thermostat Rationality. P218F - Reductant No Flow Detected. U0001-00 - CAN C BUS. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P2281 - Air Leak Between MAF and Throttle Body. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault:P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low.

ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDTC has been set:U1111-00 - Lost Odometer Message(DD, DF, and DP with Diesel Engine Only). In addition, the customer may notice one or more of the following conditions: The customer may notice a harsh 2-3 and/or 3-4 shift(2017 MY D2 with ETK 6.7L Diesel and DF2 Transmission Only). 1-2 hard shift. 3-4 flare issue fix. Trans quick learn fix(Gas Engine Only). Transmission oil temperature light illumination during high engine and tow loads. Less than desired towing performance while using cruise control. Harsh engagement while shifting from neutral to drive, neutral to reverse,or park to reverse with vehicle still in motion (rolling garage shift). Engine flare during 2-1 tip in downshift. Less than desired shift quality during 6-5 and 5-4 coasting downshifts. Delayed downshifts in Tow/Haul mode while driving down grades. Less than desired transmission shift performance when transitioning froma low traction to high traction surfaces i.e. ice covered road to clear pavement. Less than desired shift points during light pedal and Wide Open Throttle(WOT) operation or while in Tow/Haul and engine brake modes. 1-2 upshift shudder correction(Diesel engine and DF2 Transmission Only). A harsh 1-2 upshift(DF2 Transmission Only). Excessive gear shifting(DF2 Transmission Only). Harsh 2-1 downshift(DF2 Transmission Only). Delayed engagement when shifting from neutral to drive, neutral to reverse,or park to reverse (garage shifts)(DF2 Transmission Only). Audible squawk noise on 4-3 downshift(DF2 Transmission Only). Poor vehicle acceleration in first gear with vehicle fully loaded(DF2 Transmission Only). MIL illumination with no defect found forDTC P253D - PTO Sense Circuit High(DF2 Transmission Only).

vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement. Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return. If you do not receive a response within 15 minutes, please proceed with normal repair.

If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: P0128 - Thermostat Rationality Improvements. P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy. Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

PERFORMANCE~ Transmission Part Numbers: RL300150AA [4x4], or RL300149AA [4x2 LHS PTO], RL300152AB 4x2 RHS PTO]~ If you are ordering an Aisin Transmission AS69RC [sales code DF2] for replacement due to code P2757 present [for 2016MY only] with the following symptoms:~ 1. Code P2757 with MIL on [Check engine light on]~ 2. Harness check is good~ 3. Vehicle build dates are from 10/15/2015 to 4/17/2016~ 4. Low miles - approximately below 1500 miles.~ Suggested repair actions:~ 1. Clear the code and test drive with light throttle attempting to engage torque converter lock up. The code P2757 will set, if torque converter lock up fails.~ 2. If the code P2757 returns: Replace Torque Converter [Part number RL335702AA] only.~ 3. Return the suspect Torque converter to FCA for review. [Follow Part retention process]

program or no function or low keyfob coin battery condition.~ Prior to replacing keyfob on MY16 vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: P0128 - Thermostat Rationality Improvements. P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy. Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High.A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P0128 - Thermostat Rationality Improvements. P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in).In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Improvement to correct engine feels like low or reduced power. Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy. Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

ext: 4720271 to arrange for Fastrac shipper

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault:P2280 - Air Flow Restriction / Leak Between Air Cleaner and MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory:P218F - Reductant No Flow Detected(automatic transmission only). P202E - (Diesel Exhaust Fluid) Reductant Injector Performance(automatic transmission only). U0001-00 - CAN C BUS(automatic transmission only). P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1(automatic transmission only). P24A5 - EGR Cooler Bypass Bank 1 Control Stuck(automatic transmission only). P207F - Reductant Quality Performance. P218F - Reductant No Flow Detected. U110E - Lost Ambient Temperature Message. The following improvements/enhancements are also included in this software release:Fuel pressure override test improvement for wiTECH(automatic transmission only). AC pressure sensor error threshold change(automatic transmission only). No crank, No start fix(automatic transmission only). Ambient Air Temperature Improvements. Stationary de-soot with WiTECH fix.

P0542, please replace the Intake Heater Grid and Relay as a set. 68210071A$ (heater grid) and 05187880A$ (relay). Inspect electrical cable between the heater grid and relay for signs of possible overheating. Replace cable as necessary.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? U110E-Lost Ambient Temperature Message ? P205E-(Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in) In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? 68RFE Transmission Overall Shift Quality Improvements ? OBD Misfire Monitoring Improvement (68RFE Trans Only)

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault:P2280 - Air Flow Restriction / Leak Between Air Cleaner and MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory:P218F - Reductant No Flow Detected(automatic transmission only). P202E - (Diesel Exhaust Fluid) Reductant Injector Performance(automatic transmission only). U0001-00 - CAN C BUS(automatic transmission only). P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1(automatic transmission only). P24A5 - EGR Cooler Bypass Bank 1 Control Stuck(automatic transmission only). P207F - Reductant Quality Performance. P218F - Reductant No Flow Detected. U110E - Lost Ambient Temperature Message. The following improvements/enhancements are also included in this software release:Fuel pressure override test improvement for wiTECH(automatic transmission only). AC pressure sensor error threshold change(automatic transmission only). No crank, No start fix(automatic transmission only). Ambient Air Temperature Improvements. Stationary de-soot with WiTECH fix.

P0542, please replace the Intake Heater Grid and Relay as a set. 68210071A$ (heater grid) and 05187880A$ (relay). Inspect electrical cable between the heater grid and relay for signs of possible overheating. Replace cable as necessary.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? U110E-Lost Ambient Temperature Message ? P205E-(Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in) In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? 68RFE Transmission Overall Shift Quality Improvements ? OBD Misfire Monitoring Improvement (68RFE Trans Only)

Upon further investigation there could be a fault code in the PCM for P1524 ? Oil Pressure Out of Range ? Camshaft Advance/Retard Disabled.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs.P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P1C54 - SCR NOx Catalyst Missing. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P0300 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0401 - EGR System Performance. P0128 - Thermostat Rationality. P218F - Reductant No Flow Detected. U0001-00 - CAN C BUS. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P2281 - Air Leak Between MAF and Throttle Body. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault:P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low.

Upon further investigation there could be a fault code in the PCM for P1524 ? Oil Pressure Out of Range ? Camshaft Advance/Retard Disabled.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following DTCs have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: **P0128 - Thermostat Rationality Improvements.** P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy.** Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

Prior to replacing a Power Sliding Backlight Cable Assembly, please contact Marc Galli by cell phone at (248) 941-8402 as he would like to gather information. In addition, if the dealership is within the Metro Detroit Area, Marc would like to analyze the vehicle in person prior to it being repaired. If Marc cannot be contacted within 15 minutes, please provide pictures of the inside lower rail of the glass to confirm (2 passenger side and 1 driver side) cable clips are fully seated as well as pictures of the (2) regulator motor cable spring plungers to confirm they are also seated. Then proceed with the repair. Please email pictures to Marc at marc.galli@fcagroup.com.

Notify independant repair facilities when they order valve body.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDTC has been set:U1111-00 - Lost Odometer Message(DD, DF, and DP with Diesel Engine Only). In addition, the customer may notice one or more of the following conditions: The customer may notice a harsh 2-3 and/or 3-4 shift(2017 MY D2 with ETK 6.7L Diesel and DF2 Transmission Only). 1-2 hard shift. 3-4 flare issue fix. Trans quick learn fix(Gas Engine Only). Transmission oil temperature light illumination during high engine and tow loads. Less than desired towing performance while using cruise control. Harsh engagement while shifting from neutral to drive, neutral to reverse,or park to reverse with vehicle still in motion (rolling garage shift). Engine flare during 2-1 tip in downshift. Less than desired shift quality during 6-5 and 5-4 coasting downshifts. Delayed downshifts in Tow/Haul mode while driving down grades. Less than desired transmission shift performance when transitioning froma low traction to high traction surfaces i.e. ice covered road to clear pavement. Less than desired shift points during light pedal and Wide Open Throttle(WOT) operation or while in Tow/Haul and engine brake modes. 1-2 upshift shudder correction(Diesel engine and DF2 Transmission Only). A harsh 1-2 upshift(DF2 Transmission Only). Excessive gear shifting(DF2 Transmission Only). Harsh 2-1 downshift(DF2 Transmission Only). Delayed engagement when shifting from neutral to drive, neutral to reverse,or park to reverse (garage shifts)(DF2 Transmission Only). Audible squawk noise on 4-3 downshift(DF2 Transmission Only). Poor vehicle acceleration in first gear with vehicle fully loaded(DF2 Transmission Only). MIL illumination with no defect found forDTC P253D - PTO Sense Circuit High(DF2 Transmission Only).

Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.

A small number of customers may experience one or more of the symptoms/conditions listed below or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Codes (DTCs) have been set. If any of the following DTCs have been set, perform the Diagnosis. ? P0456 Evap System Small Leak. ? P2610 - PCM Internal Engine Off Timer Performance.

Module (PCM) with the latest available software. NOTE: This bulletin fixes all vehicles listed and also contains an optional software path for situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode (optional software available for D2 & DJ vehicles). There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage OPTIONAL. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): ? P0456 - Evap System Small Leak. ? P3402 - Cylinder 1 Deactivation Control Performance. ? P3426 - Cylinder 4 Deactivation Control Performance. ? P3442 - Cylinder 6 Deactivation Control Performance. ? P3450 - Cylinder 7 Deactivation Control Performance. ? P2610 - PCM Internal Engine Off Timer Performance set in the PCM memory. In addition to the DTC listed above, the software update will improve: Improved Cruise Control Acceleration mode. ? Improved Multi Displacement System operation. 6-Speed Automatic 66RFE transmission (Sales Code DFP). ? Multi Displacement System function improved while in PTO stationary mode. 6-Speed Auto Aisin AS66RC transmission (Sales Code DF3). ? Potential small improvement in fuel economy at higher altitudes. ? Potential improvement in high altitude eng

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): P2610 - PCM Internal Engine Off Timer Performance set in the PCM memory. In addition to the DTC listed above, the software update will improve the EGR monitor status function.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? U110E-Lost Ambient Temperature Message ? P205E-(Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in) In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? 68RFE Transmission Overall Shift Quality Improvements ? OBD Misfire Monitoring Improvement (68RFE Trans Only)

stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

&Rear Door

Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.

Before replacing the blower motor please call one of these individuals:~ First call Brad Bartkowicz at cell (586) 808-4114~ If no answer, then call Vince Celli at cell (586) 630-8136~ If not response in 15 minutes, continue with repair.

Before replacing any of the part numbers listed above, please call any of the following people for each vehicle type. (If you don't get an answer within 15 minutes,then proceed with the repair.):~ WD/WK--68224166AB - Front Ken Deneau, cell (248)-765-0288~ 68089094AA - Rear Pat Presti- cell (248) 379-0972~ KL/UF/PF- 68223053AB, 68225055AA Mark Ware, cell (248) 705-3469~ F500- 68093422AB,Matt Sasina, cell (248)-464-4982 or Bryan Bremer cell (248) 429-9014~ RT- 68029719AB - Front, Matt Filipkowski cell (248) 877-9106~ 05183147AA - Rear, Ken Deneau, cell (248)-765-0288

Engineering would like to have both parts returned for analysis. Also, please take a picture of the parts and email the picture, a short discription of the issue, and the last 8 digits of the VIN to Brigitte.Wicks@fcagroup.com. Thank you.

Before replacing the compressor call FCA Release Engineer Mark Briolat at cell (248) 345-0127. If no response in 15 minutes, continue with the repair.

intermittent by driving under heavy throttle will produce a C1494-92 DTC, if yes, please call FCA axle engineering and do not replace the PTU. Bruce Michel at cell (248) 260-8641, or Jian Zhu at cell (248) 379- 1132. If neither answers with 15 minutes then proceed with the repair. ~ If the service 4WD light lamp is on steady then replace the Power Transfer Unit.

information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com

Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data.

If the power steering pump is being replaced because the power steering fluid flow or pressure readings are below specification, the power steering fluid reservoir and cap assembly should also be replaced. Power steering reservoir and cap assembly 52126151AG or later should be used.

or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following DTCs have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: **P0128 - Thermostat Rationality Improvements.** P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy.** Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

warranty concern on a 2016 model year only vehicle please call Dennis Battle at cell (734) 231-1540 prior to the repair. If Dennis cannot be reached within 15 minutes then proceed with the repair.

following information to be shared with the engineer. All Active and Inactive P-Codes~ - Refractometer concentration~ - WiTech Concentration~ - WiTech Concentration Sensor Temperature ~ - Urea Tank Temperature~ - Urea Tank level when fault was set~ - Hydrocarbon reading~ - Known fill history before and after the fault was set~ - Recent weather conditions in the area~ - Actions Taken since vehicle had been brought to the dealership ~ Please contact Gary Pleyte at cell (248) 705-3567 or Makenna Coe Smith at cell (248) 202-7545 with the above information. If you are unable to get a response within 15 mins, please continue with the repair according to the trouble tree for P207F.

stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~

Module/Powertrain Control Module (ECM/PCM) with the latest available software. These DTCs have been changed from a one trip fault to a two trip fault: P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. P207F - Reductant Quality Performance. P218F - Reductant No Flow Detected. U110E - Lost Ambient Temperature Message. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Ambient Air Temperature Improvements. Stationary de-soot with WiTech fix.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. **These DTCs have been changed from a one trip fault to a two trip fault: P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High** A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only).** U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix.** OBD Misfire Monitoring Improvement (68RFE Only).

PERFORMANCE~ Transmission Part Numbers: RL300150AA [4x4], or RL300149AA [4x2 LHS PTO], RL300152AB 4x2 RHS PTO]~ If you are ordering an Aisin Transmission AS69RC [sales code DF2] for replacement due to code P2757 present [for 2016MY only] with the following symptoms:~ 1. Code P2757 with MIL on [Check engine light on]~ 2. Harness check is good~ 3. Vehicle build dates are from 10/15/2015 to 4/17/2016~ 4. Low miles - approximately below 1500 miles.~ Suggested repair actions:~ 1. Clear the code and test drive with light throttle attempting to engage torque converter lock up. The code P2757 will set, if torque converter lock up fails.~ 2. If the code P2757 returns: Replace Torque Converter [Part number RL335702AA] only.~ 3. Return the suspect Torque converter to FCA for review. [Follow Part retention process]

Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High.A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P0128 - Thermostat Rationality Improvements. P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in).In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Improvement to correct engine feels like low or reduced power. Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy. Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

Suspect stock of part number: 04627694AAmust be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before17 April, 2017.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

4720271 to arrange for Fastrac shipper

A customer may describe the following: **Cluster stays awake after ignition is turned off for 10 minutes or more.** False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault: P0421 - Catalyst 1 Efficiency Below Threshold Bank 1. P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: P0128 - Thermostat Rationality Improvements. P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: Engine Noise Improvements. Engine Hesitation Improvement. Improved Engine Fuel Economy. Reduction in engine noise during regeneration at idle. 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

Please do not disturb seal in retainer.~ Cummins Engineering is currently investigating the root cause of the oil leak concern. If there are any questions, please contact Chad Eichbrecht at cell (248) 309-2695 If you do not receive a response within 15 minutes, please proceed with normal repair.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. DTCs have been changed from a one trip fault to a two trip fault: **P0421 - Catalyst 1 Efficiency Below Threshold Bank 1.** P2280 - Air Flow Restriction / Leak Between Air Cleaner And MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: P2281 - Air Leak Between MAF and Throttle Body. P218F - Reductant No Flow Detected. P0218 - Transmission High Temperature Operation Activated (68RFE Only). P0868 - Line Pressure Low, MIL Action (68RFE Only). U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **Reduction in engine noise during regeneration at idle.** 68RFE Transmission Overall Shift Quality Improvements. Test results fix for partial range misfire (68RFE Only). Ambient Air Temperature Improvements. Stationary Desoot with wiTECH Fix. OBD Misfire Monitoring Improvement (68RFE Only).

vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement. Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return. If you do not receive a response within 15 minutes, please proceed with normal repair.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.

contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

A customer may describe the following: Cluster stays awake after ignition is turned off for 10 minutes or more. False message ?Battery Voltage Low - Start Engine to Change Ride Height? which appears in the Electronic Vehicle Information Center (EVIC). This condition may occur when the vehicle is first started and the suspension is switched from alternate trailer ride height to normal ride height.

P0542, please replace the Intake Heater Grid and Relay as a set. 68210071A$ (relay) and 05187880A$ (grid). Inspect electrical cable between the heater grid and relay for signs of possible overheating. Replace cable as necessary.

(P0300- P0306), please also replace the High Pressure Connector Tube and return tube with the injectors.

leak, replace seal and retainer as a set PN; 9003466. Please do not disturb seal in retainer when removing from engine.~ Cummins Engineering is currently investigating the root cause of the oil leak concern. If there are any questions, please contact Chad Eichbrecht at cell (248) 309-2695~ If you do not receive a response within 15 minutes, please proceed with normal repair

thread damage to the oil filter connector (Spud), DO NOT replace the entire adapter assembly. The oil filter connector is available separately (Part Number 04429355).~ If ordering an adapter due to some other issue, you must also order an oil bypass valve Mopar Part # 04797726AB, as these are not reusable. Please refer to all applicable published service information for oil bypass valve installation

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance.** P0456 - EVAP System Small Leak.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance.** P0456 - EVAP System Small Leak. P3402 - Cylinder 1 Deactivation Control Performance. P3426 - Cylinder 4 Deactivation Control Performance. P3442 - Cylinder 6 Deactivation Control Performance. P3450 - Cylinder 7 Deactivation Control Performance. P2610 - PCM Internal Engine Off Timer Performance set in the PCM memory. In addition to the DTCs listed above, the software update will improve: **Correct an issue related to rounding of the cruise control set speed displayed in the cluster. Brake Throttle Override calibration has changed to be less sensitive. Throttle Body supplier change has caused a widening of the minimum and maximum voltage limits Correct a software issue with oil pressure light function at key-up. Correct a software issue related to idle timer. Correct a software issue with inconsistent engine RPM increments/decrements with operator idle speed.(DD/DF/DP ONLY).** Improved Cruise Control Acceleration mode. Improved Multi Displacement System operation 6-Speed Automatic 66RFE transmission (Sales Code DFP). Multi Displacement System function improved while in PTO stationary mode. 6-Speed Auto Aisin AS66RC transmission (Sales Code DF3). Potential small improvement in fuel economy at higher altitudes. Potential improvement in high altitude engine idle RPM stability. EGR monitor status function.

vehicle to listen for audible ?drone? noise at approximately 2,000 RPM. If drone noise is verified, normal torque converter replacement should be performed. The customer may describe a ?heavy droning noise? coming from the vehicle at an engine speed range of 1,800 RPM to 2,000 RPM with mid to deep throttle applied.

Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair."

PERFORMANCE~ TRANSMISSION PART NUMBERS: RL300150AA [4X4], OR RL300149AA [4X2 LHS PTO], RL300152AB 4X2 RHS PTO]~ IF YOU ARE ORDERING AN AISIN TRANSMISSION AS69RC [SALES CODE DF2] FOR REPLACEMENT DUE TO CODE P2757 PRESENT [FOR 2016MY ONLY] WITH THE FOLLOWING SYMPTOMS:~ 1. CODE P2757 WITH MIL ON [CHECK ENGINE LIGHT ON]~ 2. HARNESS CHECK IS GOOD~ 3. VEHICLE BUILD DATES ARE FROM 10/15/2015 TO 4/17/2016~ 4. LOW MILES - APPROXIMATELY BELOW 1500 MILES.~ SUGGESTED REPAIR ACTIONS:~ 1. CLEAR THE CODE AND TEST DRIVE WITH LIGHT THROTTLE ATTEMPTING TO ENGAGE TORQUE CONVERTER LOCK UP. THE CODE P2757 WILL SET, IF TORQUE CONVERTER LOCK UP FAILS.~ 2. IF THE CODE P2757 RETURNS: REPLACE TORQUE CONVERTER [PART NUMBER RL335702AA] ONLY.~ 3. RETURN THE SUSPECT TORQUE CONVERTER TO FCA FOR REVIEW. [FOLLOW PART RETENTION PROCESS]"

the following: **Cluster stays awake after ignition is turned off for 10 minutes or more.** False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.

SYMPTOM/CONDITION: A customer may describe the following: **Cluster stays awake after ignition is turned off for 10 minutes or more.** False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.

PROCEDURE ON REPROGRAMMING ENGINE CONTROL MODULE/POWERTRAIN CONTROL MODULE WITH LATEST SOFTWARE AVAILABLE *CN

Line Heater Control Circuit High, and U11C1 Reductant Control Module Received Implausible Data From ECM/PCM, Set

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

NOx Sensor Diagnostic Trouble Codes (DTCs) Diagnosis Information.

rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.

Some customers may experience a no start issue when turning the key fob in the ignition node module(Fig. 1).

damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

To verify proper functionality, turn on the ignition with no cables or devices plugged into the port. Connect a charging cable to the port, then connect the device. If the device receives power, the port is functioning to design. There are some minor compatibility issues with some charging cables including Apple Lightning cables. For questions regarding the charging port functionality, please call Dave Diovardi at Cell (248) 941-8704 or Rick Gordon at Cell (248) 630-6281.~

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Some customers may experience a diminished or less than satisfactory range when trying to lock/unlock the doors or when using the remote start from the key fob. Some customers may also experience a Tire Pressure Monitoring (TPM) icon illuminated while all the tires are properly inflated.

Customers may experience one or more of the following: Satellite radio reception improvements. Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. (U.S. Market Only) (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle. (U.S. Market Only)

Customers may describe the instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following DTCs set in the PCM memory: P064F - Unauthorized Software/Calibration Detected. P218F - Reductant No Flow Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. U0001-00 - CAN C BUS. P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P207F - Reductant Quality Performance. P218F - Reductant No Flow Detected. U110E - Lost Ambient Temperature Message. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to a two trip fault:P2280 - Air Flow Restriction / Leak Between Air Cleaner and MAF. P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. P208D - (Diesel Exhaust Fluid) Reductant Pump Control Circuit High. The following improvements/enhancements are also included in this software release:Fuel pressure override test improvement for wiTECH. AC pressure sensor error threshold change. No crank, No start fix. Ambient Air Temperature Improvements. Stationary de-soot with WiTECH fix.

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

the latest available software and if necessary replacing the unit. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Codes (DTCs):P207F - Reductant Quality Performance. P202C - Reductant Tank Heater Control Circuit High. P203B - Reductant Level Sensor 1 Circuit Performance.

The customer may describe the headlamps flicker while operating at night. This condition may be more prevalent after the bulb(s) have been replaced with an aftermarket bulb.

Customers may experience one or more of the following:?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. HVAC temperature out of sync with radio display (KL vehicles). Improvements:Adds Apple Siri Eyes Free capability for iPhone owners. Add the ability to drag and drop icons into the menu bar. Enhanced Voice Recognition (VR) performance. Media devices, phone pairing, and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature. Satellite radio reception improvements.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

the latest available software and if necessary replacing the unit. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Codes (DTCs): P207F - Reductant Quality Performance. P202C - Reductant Tank Heater Control Circuit High. P203B - Reductant Level Sensor 1 Circuit Performance.

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

A customer may experience, one or more of the following conditions: ? Radio may reset, turn itself off and then back on again. All Symptom Listed Below Are For 2013 Vehicles Only: ? Radio may be muted. Any of DTCs B1400-92-Front Left Audio Speaker Output - Performance Incorrect Operation and/or B1404-92- Front Right Audio Speaker Output - Performance Incorrect Operation and/or B1408-92-Rear Left Audio Speaker Output - Performance Incorrect Operation and/or B140C-92-Rear Right Audio Speaker Output - Performance Incorrect Operation, maybe active or stored. ? Radio display screen may turn off. ? Radio will stay on after the vehicle is turned off with remote. (Applies to vehicle with Mopar remote start add on package only). ? Radio will stay on for 20 minutes after ignition is turned off and the only way to turn off the radio is by pressing the power button on the radio. Software was updated to have the radio shut off based on the cluster accessory delay setting.

identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68260866AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 68085880AD, 68085880AF, 68085881AE, 68085881AF, 68085881AG. Replacement part numbers are: 68085880AG, and 68085881AH. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

are receiving this email as you have been identified to have stock on hand or have stock in transit to your dealership. Reports of dealers receiving incorrect fuel pressure sensors packaged as 68210332AA. Correct and suspect parts can be identified visually by the color of the label on the sensors. Correct sensors have white color label on the part whereas the suspect sensors have yellow colored labels. Reference pictures attached for visual identification. Please inspect stock on hand and return any suspect parts found back to your facing PDC using MRA code 02. Replacement parts can be obtained by reordering the same part number. Direct all questions via email to vn83@chrysler.com

The radio should not be replaced for this issue if the fault is stored, if the code cannot be reproduced and no trouble can be found (radio functions properly). In this case it is no impact to the customer in any way. Do NOT replace the radio for this issue. Please contact John Carlesimo at cell (248) 941-8756 if you have any further questions regarding this fault.

contact Michael Wang at cell (248) 701-5351. If no response or contact is made within 15 minutes, proceed with repairs as necessary.

Please identify battery with the last 8 VIN digits along with the 15 digit Medtronic code from the GR-8 tester. If no response in 15 minutes, continue with the repair. Battery needs to be held and not turned in for core charges.

A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:

have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016.

the latest available software and if necessary replacing the unit. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Codes (DTCs): P207F - Reductant Quality Performance. P202C - Reductant Tank Heater Control Circuit High. P203B - Reductant Level Sensor 1 Circuit Performance.

Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017.

Customers may describe the instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).

the latest available software and if necessary replacing the unit. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Codes (DTCs):P207F - Reductant Quality Performance. P202C - Reductant Tank Heater Control Circuit High. P203B - Reductant Level Sensor 1 Circuit Performance.

The customer may describe the headlamps flicker while operating at night. This condition may be more prevalent after the bulb(s) have been replaced with an aftermarket bulb.

Customers may experience one or more of the following:?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. HVAC temperature out of sync with radio display (KL vehicles). Improvements:Adds Apple Siri Eyes Free capability for iPhone owners. Add the ability to drag and drop icons into the menu bar. Enhanced Voice Recognition (VR) performance. Media devices, phone pairing, and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature. Satellite radio reception improvements.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.

Some customers may experience a no start issue when turning the key fob in the ignition node module(Fig. 1).

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

connector(s) on a 2015-2016 model year 5.7L Hemi DS, D2, DD, DJ or DX truck, please call Lou Nigro at cell (810) 293-3858. If no response is received within 15 minutes, please continue with repair.~

The customer may describe the headlamps flicker while operating at night. This condition may be more prevalent after the bulb(s) have been replaced with an aftermarket bulb.

updating Radio Frequency Hub Module (RFHM) software to latest version. The customer may describe one or more of the following: Instrument cluster backlighting may start flickering. This usually occurs when the dimming is in the lower settings (high-line instrument panels only). The cruise control set speed does not match the digital speedometer (BUX vehicles only).

SYMPTOM/CONDITION: A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).

SYMPTOM/CONDITION: A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).

this is normal and not a defect.

This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2023 to 2013 HD Trucks. The following information is intended to eliminate confusion.

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

semi and full synthetic oils.

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

The customer may describe what appears to be a gap between the left applique and the RamBox lid. Applique may separate at lid, due to insufficient adhesive bond strength.

Detected Message

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

MasterShield Products in stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers: 82212074, 82212075, 82212076, 82212077, 82212078, & 82213598 . Please return suspect parts back to your facing depot using Return Code 02, before 18 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all suspect stock of following part number: 05026886AJ. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 02 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

If no response is received within 15 minutes, then proceed with required repair.

Call Mike Wicker at cell (248) 821- 9350 with the Fault Code, so we can determine true root cause. If your call is not returned within 15 minutes, please continue with the repair

covers and seat cover repairs.

Please return all stock of part number 68288760AA. Replacement part number is 68288760AB. Replacement parts w ill be available w eek ending 5/6/16. Please return suspect parts back to your facing depot using Return Code 02, before 26 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 68003062AB, 68003083AB, 68003085AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 1PE001W 7AB, 1PE011W 7AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

As per regulatory compliance: Please return follow ing stock of part numbers: 82214711, 82214712, 82214713, 82214714, 82214715, 82214716, 82214717, 82214718, 82214720, 82214721, 82214722, 82214723, 82214724, 82214725, 82214726, 82214727, 82214728, 82214729, 82214730, 82214731, 82214732. Please return parts back to your facing depot using Return Code 02, before 31May, 2016.

Please return suspect stock of following part numbers: 68050625AA, 68050626AA, 68050627AA, 68050628AA, 68050743AA, 68050744AA, 68050839AA, 68050841AA, 68257133AA, 68257134AA, 68264578AA, 68264579AA, 68264580AA, 68264581AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 April, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return parts which have a pacakging date code of July 20th 2016. Reference pictures attached for suspect part identification. Please return parts backto your facing depot using Return Code 02, before 31 August, 2016.

The customer may describe what appears to be a gap between the left applique and the RamBox lid. Applique may separate at lid, due to insufficient adhesive bond strength.

Please return suspect stock of part number 68143886AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 68174065AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 68141880AH, 68141881AH, 68145625AI, 68145626AI, 68189480AF and replacement part numbers are 68141880AI, 68141881AI, 68145625AJ, 68145626AJ & 68189480AG respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 05278632AF and replacement part number is 52030379AA which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 1YG06JSCAC, 1YG06KEPAC, 1YG 06KFSAC, 1YG 06KGZAC, 1YG 06KBUAC and replacement part numbers are 1YG 1YG06KFSAD, 1YG 06KG ZAD, 1YG 06KBUAE respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 68188889AE and replacement part number is 68188889AF which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of following part numbers: 68036213AA, 68036230AF, 68158196AC, 68158197AD, & 68158454AD. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allstock of following part numbers:68241568AB,68241568AC,68241569AB,68241569AC, 68241570AB,68241571A.Replacement part numbersare 68241568AD,68241569AD,68241570AD,68241571AD, which are in stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

This same month last year we had over 40,000 open aged > 5 days tickets. As a result of focused efforts to verify vehicles are repaired and close tickets the number is now at just under 7,000 tickets.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

being opened or closed.

Mirror Contacts Door Window Glass In The Folded Position.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

**This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

front corners of the sunroof.

front corners of the sunroof.

**This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**

industry awareness regarding the recommended usage of Authentic Mopar Glass.

identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 05182600AC. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock,or have stock in transit to your dealership. Please return all suspect stock of following part numbers:68159725AB,& 68261143AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02,before 27 O ctober,2015. Return any open orders in process too. Direct all questions via email to MO PARQ C@fcagroup.com

LT:04805839AD

To do this, add the LEG (Trailer Tow Mirrors) sales code to the VIN using DealerCONNECT and then performing a vehicle re-configuration using the WiTech tool.~ After Kit is completely installed, perform the following;~ 1. Add LEG sales code to the VIN under the ?Vehicle Option Updates? Found on Dealerconnect~ 2. Update Vehicle Configuration by using the WiTech tool and performing ?Restore Vehicle Configuration.?

**This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**

An insufficient urethane bead around the metal bracket results in water leaking into the vehicle at one or both of the front corners of the sunroof.

stock in transit to your dealership. Please return suspect stock of part number 68160775AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 26 August, 2016.

A)

Please return allsuspect stock of part numbers:68212041AC,68141170AC,55112738AA.See attachmentsfor identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Please return all suspect stock of following part numbers: 57010364AI, 57010365AI, 57010504AJ, 57010505AJ, 68224368AB, 68224369AB. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017.

numbers:55395241AG,55395241AE.Replacement ispart number 55395241AH which isin stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 12April,2017

have stock in transit to your dealership. Please return suspect stock of part number 04589131AG, 04589243AG . See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 7 April, 2016.

The customer may describe scratches on the driver?s side of roof.

The customer may describe a binding or audible clicking condition when the center console lid is being opened or closed.

The customer may notice a large gap where the center stack meets the instrument panelFig.1.Gap at Center Stack Trim

The customer may notice the glass cover trim is loose or shows a gap on either of the rear doorFig.1.Gap Identified at Door

Diesel Exhaust Fluid (DEF) System Diagnostic Trouble Codes (DTCs) due to Hydrocarbon Contamination.

2019 RAM 3500 Pickup (D2)

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P218F - Reductant No Flow Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. The customer will not notice any drivability issues associated with these DTCs. These DTCs may set when the vehicles is parked for a long time and the ambient temperatures are below -11 C (12 F).

guidelines.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

The customer may describe the following: A chatter, shudder, or vibration from the rear axle during turns. This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axlefluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components.This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every2 years or 20,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual.

either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 68146401AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock, or have stock in transit to your dealership. Please return following part numbers: CBTTP57FAA, & CBTTP57FAB. Replacement part number CBTTP57FAC will be available week beginning 26 O ct., 2015. There are reports of pre-programmed FO BS in these kits, preventing dealer pairing of W IN and Transmitter Key FO BS. If repair is needed prior to new part availability, order two of part number 05026886AK transmitter Integrated Key FO B. Please return suspect parts back to your facing depot using Return Code 02, before 06 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

(248) 622 8109 ~ Mexican Dealers please call Ricardo Lozada at cell +52 1 55 1370 3187. If no return call in 15 minutes, continue with repair.

please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair.

A customer may experience one or more of the following conditions: Radio display screen will lock up and reset intermittently. Incorrect routing directions to fuel stations when using Travel Link. Unable to turn on heated seats; icon is greyed out. Navigation screen goes blank. Navigation system freezes/locks up. Vehicles with Mopar special edition radio will update radio?s splash screen. Navigation icon shows the vehicle going backward when it?s moving forward.

stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

guidelines.

Please return allsuspect stock of part numbers:68148794AH,68148794AF,68148794AD,68156453AH,68156453AF, 68156453AD,68161542AE,68161542AD.See attachment for identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

please also replace the fan clutch assembly using current Mopar stock (part number 52014729A$).~ Once installed, contact Christine Donegan at (866) 799-1692 ext 1257 to initiate a fast track request for the return of the parts for analysis.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

turns and customer has the following: 1) Limited Slip Differential 2) No record of rear axle oil being serviced in the last 20,000 miles 3) No apparent damage to the axle/differential case or differential case internal gears Service the rear axle oil with new and test drive to see if condition is still present. If still present follow standard diagnostic procedures and contact FCA Redacted Content for further assistance.

the following scenario occurs; The T79 or U11 recall was completed where the shifter inspection was acceptable and the software flash was performed but then the customer comes back needing the BTSI bracket replaced for coming out of park without the brake or key.

If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any DTCs identified with the scan tool and document them on the repair order.

check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.

please also replace the fan clutch assembly using current Mopar stock (part number 52014729A$).~ Once installed, contact Christine Donegan at (866) 799-1692 ext 1257 to initiate a fast track request for the return of the parts for analysis.

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?

Module (TCM) with the latest available software. Some customers may experience one or more of the following conditions: A harsh 1-2 upshift. Excessive gear shifting.

Module (TCM) with the latest available software. Some customers may experience one or more of the following conditions: A harsh 1-2 upshift. Excessive gear shifting.

converter after verifying that an internal snap ring has dislodged. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) set in the Transmission Control Module (TCM) memory: P2757-00 - TCC Pressure Control Solenoid Control Circuit Performance.

Module (TCM) with the latest available software. Some customers may experience one or more of the following conditions: A harsh 1-2 upshift. Excessive gear shifting.

converter after verifying that an internal snap ring has dislodged. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) set in the Transmission Control Module (TCM) memory: P2757-00 - TCC Pressure Control Solenoid Control Circuit Performance."

PLEASE ALSO REPLACE THE FAN CLUTCH ASSEMBLY USING CURRENT MOPAR STOCK (PART NUMBER 52014729A$).~ ONCE INSTALLED, CONTACT CHRISTINE DONEGAN AT (866) 799-1692 EXT 1257 TO INITIATE A FAST TRACK REQUEST FOR THE RETURN OF THE PARTS FOR ANALYSIS."

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure.

not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

The customer may describe the Electronic Stability Control (ESC) Warning lamp is illuminated on the instrument cluster. Upon further inspection, the technician may find the following Diagnostic Trouble Code (DTC): C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure.

Start Date: 10/27/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of part numbers: 68144663AA, 52013874AE. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to MOPARQC@fcagroup.com

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.

18.01.35 (BU Vehicles)

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

CAUTION: Confirm the correct radio flash file to the applicable model and family vehicle before flashing. A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may lock up. ? Back up display may not turn off. ? Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. ? Charging schedule showing in the setting menu (FF BEV only). ? Korean language was not supported (APAC - Korea only). Enhancement: ? Removing the charging schedule from showing in the setting menu (FF BEV only). ? Adding Korean language support (APAC - Korea only).

CAUTION: Confirm the correct radio flash file to the applicable model and family vehicle before flashing. A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may lock up. ? Back up display may not turn off. ? Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. ? Charging schedule showing in the setting menu (FF BEV only). ? Korean language was not supported (APAC - Korea only). Enhancement: ? Removing the charging schedule from showing in the setting menu (FF BEV only). ? Adding Korean language support (APAC - Korea only).

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

A customer may experience one or more of the following: Radio display screen intermittently may go blank. Radio display screen may lock up. Back up display may not turn off. Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. Korean language was not supported (APAC - Korea only). Additional Enhancements: Removed the charging schedule from showing in the setting menu (FF BEV only). Adding Korean language support (APAC - Korea only).

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

DO NOT order a NEW radio from Mopar. Go back and order a "Z" level part number. (example: Z8249986A$) The MY16 replacement radios must be reconfigured by United Radio to the wireless network provider in order for Uconnect Apps to work properly.

Diagnostic Trouble Code (DTC) P207F ? Reductant Quality Performance Set.

industry awareness regarding the use of recycled or salvage parts.

Diagnostic Trouble Code (DTC) P207F ? Reductant Quality Performance Set.

industry awareness regarding the use of recycled or salvage parts.

Please return suspect stock of following part numbers: 68110016AC, 68110016AD, 68110016AE, 68110017AD, 68236104AC, 68236105AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31 August, 2016.

The customer may describe that the headlamps are out of alignment or oncoming vehicles are flashing their bright lights at them.

OVERVIEW: This bulletin involves adjusting the headlamps to specified alignment. SYMPTOM/CONDITION: The customer may describe that the headlamps are out of alignment or oncoming vehicles are flashing their bright lights at them.

OVERVIEW: This bulletin involves adjusting the headlamps to specified alignment. SYMPTOM/CONDITION: The customer may describe that the headlamps are out of alignment or oncoming vehicles are flashing their bright lights at them.

spare tire winch cable when storing under the vehicle. The adapter is part number 6824863AA and requires three (3) mounting nuts; PN 68150129AA.

call one of the individuals below.~ Steve Rice at cell (248) 867 0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.

Please return stock of part number 68103256AG packaged before 2016/08/01. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

A test-drive snap shot may help you isolate the source of the issue.

B)

drag link replacement ensure that the welded draglink toe setting procedure has been followed first. ~ ~ Service Library: 02 - Front Suspension / Wheel Alignment / Standard Procedure / TOE SETTING PROCEDURE FOR TRUCKS WITH DRAG LINK RECALL WELD ~

as either having stock, or have stock in transit to your dealership. Please return all suspect stock of follow ing part number: 68245351AB. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

technician an overview of the steps a customer will need to take to complete the update.

If no response in 15 minutes, proceed with ordering the part

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.