2015 Ram 3500 TSBs

Components are needed by Engineering and Production due to limited availability. To avoid being charged the full replacement value, return within 60 days 68295359AD 68347098AC 68232683AG 68347099AC"

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following DTCs have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance.

installed in the vehicle.

with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance. P0234 - Turbocharger Overboost Condition.

Pickup (D2)

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

Module/Powertrain ControlModule (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of thefollowing DTCs have been set: P064F - Unauthorized Software/Calibration Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1C55 - NOx Sensor Intermittent ? Bank 1 Sensor 1. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P020A - Fuel Injector 1 Performance. P020B - Fuel Injector 2 Performance. P020C - Fuel Injector 3 Performance. P020D - Fuel Injector 4 Performance. P020E - Fuel Injector 5 Performance. P020F - Fuel Injector 6 Performance. U0001 - Can C Bus. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor CircuitIntermittent (setting when the block heater is plugged in). U110E - Lost Ambient Temperature Message. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance. In addition, the following software enhancements are also available: A/C pressure sensor update. Improvements made to reduce misfire. wiTECH engine cooling fan actuation test update. Improved Exhaust Gas Recirculation (EGR) valve response. Over Running Clutch (ORC) software improvement. Unpleasantodor in the vehicle at low speeds during regeneration cycle.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance.** P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P0307 - Cylinder 7 Misfire. P0308 - Cylinder 8 Misfire.

Do Not Replace Turbocharger for Exhaust Brake Operation Complaints. Do not replace the turbocharger for complaints of exhaust brake operating when the Exhaust Brake switch is off. Replacing the turbocharger will not address these complaints. Update the PCM with the new software version to correct this issue. 2. Turbo Speed Sensor is Now Serviceable. If a Turbocharger Speed Sensor is being replaced for a P2580 or any other reason, the Turbo Speed Sensor is now available separate from the Turbocharger Kit. do not replace the entire Turbocharger Kit. 2013-2015 Chassis Cab or Pickup - PN 68210095A$ 2007-2012 Chassis Cab or Pickup - PN 68039104A$. 3. Replace Exhaust Gaskets with Turbocharger Removal.~ If turbocharger is removed/replaced, the following items are not reusable and must be replaced: Turbocharger Gasket Turbocharger Outlet Seal Turbocharger Band Clamp If the front exhaust pipe is removed/replaced, the following items are not reusable and must be replaced. Turbocharger Outlet Seal Turbocharger Band Clamp

Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). U110E - Lost Ambient Temperature Message. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **Ambient Air Temperature Improvements. 68RFE Transmission Overall Shift Quality Improvements.** SCR Efficiency scan tool test improvement. Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. Cold idle speed stability improvement. Charging system improvements for dual alternator applications. Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). Fuel Filter Minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.

(ECM) with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel.

Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA, 68046015AA, 68100682AA, 68100676AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair.~ ~___________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A, 05086754A, 05015705A. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~_________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following DTCs have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance.

with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance. P0234 - Turbocharger Overboost Condition.

Pickup (D2)

installed in the vehicle.

with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For The Following Diagnostic Trouble Codes (DTCs): ? U3017 - Control Module Timer/Clock Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P2281 - Air Leak Between MAF And Throttle Body. Other Software Improvements: ? Fuel Filter Minder calibration changes. ? wiTECH Fuel Pressure Override and Fuel System Run Up test improvements. ? EGR system improvement to help prevent freeze up. ? Diesel Exhaust Fluid (DEF) system enhancement during stationary regeneration.

with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find oneor more of the following Diagnostic Trouble Codes (DTCs): P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P0307 - Cylinder 7 Misfire. P0308 - Cylinder 8 Misfire.

There will be a choice between two calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have hadthe ammonia sensor removed. Be sure to select the correct software based on vehicle configuration.Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Uponfurther investigation the technician may find that one or more of the following DTCs have been set: P064F - Unauthorized Software/Calibration Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. U0001 - Can C Bus. P20EE - Selective Catalytic Reduction (SCR) NOx Catalyst Efficiency BelowThreshold - Bank 1 (For ammonia sensor equipped vehicles). P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia sensor deletedsystems only). P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor CircuitIntermittent (setting when the block heater is plugged in). P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. U3017 - Control Module Timer/Clock Performance. U1421 - Implausible Ignition Key Off Time Received. P2281 - Air Leak Between MAF And Throttle Body. In addition, the following software enhancements are also available: A/C pressure sensor update. wiTECH engine cooling fan actuation test update. Ambient air temperature improvements. Operational improvement for dual alternators. Selective Catalytic Reduction (SCR) efficiency scan tool test improvement. Fuel filter minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements. Exhaust Gas Recirculation (EGR) system improvement to help prevent freezeup. Diesel Exhaust Fluid (DEF) system enhancement during stationary regeneration.

with thelatest available software. The customer may describe extended engine cranking or starting times when the Compressed Natural Gas (CNG) tank level is low(DJ only) (Sales Code EZF only).Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigationthe technician may find one or more of the following Diagnostic Trouble Codes (DTCs)P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P0307 - Cylinder 7 Misfire. P0308 - Cylinder 8 Misfire.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance. P0234 - Turbocharger Overboost Condition.

Pickup (D2)

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDTC has been set:U1111-00 - Lost Odometer Message(DD, DF, and DP with Diesel Engine Only). In addition, the customer may notice one or more of the following conditions: The customer may notice a harsh 2-3 and/or 3-4 shift(2017 MY D2 with ETK 6.7L Diesel and DF2 Transmission Only). 1-2 hard shift. 3-4 flare issue fix. Trans quick learn fix(Gas Engine Only). Transmission oil temperature light illumination during high engine and tow loads. Less than desired towing performance while using cruise control. Harsh engagement while shifting from neutral to drive, neutral to reverse,or park to reverse with vehicle still in motion (rolling garage shift). Engine flare during 2-1 tip in downshift. Less than desired shift quality during 6-5 and 5-4 coasting downshifts. Delayed downshifts in Tow/Haul mode while driving down grades. Less than desired transmission shift performance when transitioning froma low traction to high traction surfaces i.e. ice covered road to clear pavement. Less than desired shift points during light pedal and Wide Open Throttle(WOT) operation or while in Tow/Haul and engine brake modes. 1-2 upshift shudder correction(Diesel engine and DF2 Transmission Only). A harsh 1-2 upshift(DF2 Transmission Only). Excessive gear shifting(DF2 Transmission Only). Harsh 2-1 downshift(DF2 Transmission Only). Delayed engagement when shifting from neutral to drive, neutral to reverse,or park to reverse (garage shifts)(DF2 Transmission Only). Audible squawk noise on 4-3 downshift(DF2 Transmission Only). Poor vehicle acceleration in first gear with vehicle fully loaded(DF2 Transmission Only). MIL illumination with no defect found forDTC P253D - PTO Sense Circuit High(DF2 Transmission Only).

A small number of customers may experience one or more of the following: ? **?Navigation Failed? message is displayed. ? Navigation is inoperative or inaccurate. ? CD player will not play songs and/or locks up the radio. ? The clock will not automatically update to local time. ? The clock may be off by several hours (RA3 only). ? HVAC temperature out of sync with radio display (KL vehicles). ? Some Uconnect App remote commands do not execute with the vehicle. ? Radio Apps are inoperative. ? Radio will lock up. Radio display screen is black or blank. Battery drain due to radio staying on.** Rearview Camera image appears jittery (UF vehicles only). Inability to establish a WiFi connection when security feature is enabled (UF vehicles only). Audio distortion/popping heard while playing Apple devices through the USB port (UF vehicles only). Remote Uconnect Apps functions (i.e. door locks, remote start) inoperative while the engine is running (UF vehicles only). HVAC temperature out of sync with radio display (KL vehicles). Intermittently blind spot chime will not turn off (KL vehicles only). The radio may switch from SiriusXMT to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Audio muted after AUX device is disconnected. In addition, the following Improvements are included: **Adds Apple SiriT Eyes Free capability for iPhoneT owners. Add the ability to drag and drop icons into the menu bar. Auto Play can now be configured. Enhanced VR performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (YelpT, PandoraT, AhaT, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature.**

If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). U110E - Lost Ambient Temperature Message. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **NOx sensor calibration improvements. (Sales Code DG7). Enhanced software for a No crank/No start issue. (U0100 - Lost Communication Ambient Air Temperature (AAT) improvements. 68RFE Transmission overall shift quality improvements. SCR Efficiency scan tool test improvement. Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. Cold idle speed stability improvement. Charging system improvements for dual alternator applications. Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). Fuel Filter Minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

converter build date and if necessary, replacing the torque converter. A small number of torque converters were manufactured with the oil grooves on the internal friction discs too wide. This may result in the transmission slipping under heavy loads causing premature wear.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

ext: 4720271 to arrange for Fastrac shipper

P0542, please replace the Intake Heater Grid and Relay as a set. 68210071A$ (heater grid) and 05187880A$ (relay). Inspect electrical cable between the heater grid and relay for signs of possible overheating. Replace cable as necessary.

a MIL illumination and DTC P229F, please do not replace any parts at this time. Cummins Engineering is currently investigating the root cause of the concern and is requesting to visit a dealership with this DTC to gather valuable information. Please contact Christine Donegan at (866) 799-1692 ext 1257~ If causal part replacement is the System Out NOx sensor (Bank 1, Sensor 2) PNs 68085740AA, or 68197109AA, please file claim under LOP 250810. If for the Engine Out NOx Sensor (Bank 1, Sensor 1) use LOP 250809.

P0542, please replace the Intake Heater Grid and Relay as a set. 68210071A$ (heater grid) and 05187880A$ (relay). Inspect electrical cable between the heater grid and relay for signs of possible overheating. Replace cable as necessary.

a MIL illumination and DTC P229F, please do not replace any parts at this time. Cummins Engineering is currently investigating the root cause of the concern and is requesting to visit a dealership with this DTC to gather valuable information. Please contact Christine Donegan at (866) 799-1692 ext 1257~ If causal part replacement is the System Out NOx sensor (Bank 1, Sensor 2) PNs 68085740AA, or 68197109AA, please file claim under LOP 250810. If for the Engine Out NOx Sensor (Bank 1, Sensor 1) use LOP 250809.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance. P0234 - Turbocharger Overboost Condition.

Pickup (D2)

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

68085740AA, or 68197109AA, please file claim under LOP 250809~

Notify independant repair facilities when they order valve body.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDTC has been set:U1111-00 - Lost Odometer Message(DD, DF, and DP with Diesel Engine Only). In addition, the customer may notice one or more of the following conditions: The customer may notice a harsh 2-3 and/or 3-4 shift(2017 MY D2 with ETK 6.7L Diesel and DF2 Transmission Only). 1-2 hard shift. 3-4 flare issue fix. Trans quick learn fix(Gas Engine Only). Transmission oil temperature light illumination during high engine and tow loads. Less than desired towing performance while using cruise control. Harsh engagement while shifting from neutral to drive, neutral to reverse,or park to reverse with vehicle still in motion (rolling garage shift). Engine flare during 2-1 tip in downshift. Less than desired shift quality during 6-5 and 5-4 coasting downshifts. Delayed downshifts in Tow/Haul mode while driving down grades. Less than desired transmission shift performance when transitioning froma low traction to high traction surfaces i.e. ice covered road to clear pavement. Less than desired shift points during light pedal and Wide Open Throttle(WOT) operation or while in Tow/Haul and engine brake modes. 1-2 upshift shudder correction(Diesel engine and DF2 Transmission Only). A harsh 1-2 upshift(DF2 Transmission Only). Excessive gear shifting(DF2 Transmission Only). Harsh 2-1 downshift(DF2 Transmission Only). Delayed engagement when shifting from neutral to drive, neutral to reverse,or park to reverse (garage shifts)(DF2 Transmission Only). Audible squawk noise on 4-3 downshift(DF2 Transmission Only). Poor vehicle acceleration in first gear with vehicle fully loaded(DF2 Transmission Only). MIL illumination with no defect found forDTC P253D - PTO Sense Circuit High(DF2 Transmission Only).

Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.

NOTE: This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph). During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: ? P3426 - Cylinder 4 Deactivation Control Performance. ? P3402 - Cylinder 1 Deactivation Control Performance. ? P3442 - Cylinder 6 Deactivation Control Performance. ? P3450 - Cylinder 7 Deactivation Control Performance. ? U0140 - Lost Communication With Body Control Module. (Attempting to clear this DTC will be unsuccessful). ? P030X - Cylinder X Misfire Detected. ? P0300 - Multiple Cylinder Misfire Detected. Additionally the following enhancements have been implemented: Improved Cruise Control Acceleration mode. Improved Multi Displacement System operation. 6-Speed Automatic 66RFE transmission (Sales Code DFP). Multi Displacement System function improved while in stationary mode. 6-Speed Auto Aisin AS66RC transmission (Sales Code DF3). Potential small improvement

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? U110E - Lost Ambient Temperature Message. ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U1421 - Implausible Ignition Key Off Time Received. ? P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? SCR Efficiency scan tool test improvement. ? 68RFE Transmission Shift Quality Improvements for low speed First to Neutral and Neutral to First (Garage Shifts). ? Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). ? Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. ? Cold idle speed stability improvement. ? Charging system improvements for dual alternator applications. ? Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). ? Fuel Filter Minder calibration changes. ? wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.

During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: ? P3426 - Cylinder 4 Deactivation Control Performance. ? P3402 - Cylinder 1 Deactivation Control Performance. ? P3442 - Cylinder 6 Deactivation Control Performance. ? P3450 - Cylinder 7 Deactivation Control Performance. ? U0140 - Lost Communication With Body Control Module. (Attempting to clear this DTC will be unsuccessful.) ? P030X - Cylinder X Misfire Detected. ? P0300 - Multiple Cylinder Misfire Detected. Additionally the following enhancements have been implemented: ? Improved Cruise Control Acceleration mode. ? Improved Multi Displacement System operation. 6-Speed Automatic 66RFE transmission (Sales Code DFP). ? Multi Displacement System function improved while in stationary mode. 6-Speed Auto Aisin AS66RC transmission (Sales Code DF3). ? Potential small improvement in fuel economy at higher altitudes. ? Potential improvement in high altitude engine idle RPM stability.

a MIL illumination and DTC P229F, please do not replace any parts at this time. Cummins Engineering is currently investigating the root cause of the concern and is requesting to visit a dealership with this DTC to gather valuable information. Please contact Christine Donegan at (866) 799-1692 ext 1257~ If causal part replacement is the System Out NOx sensor (Bank 1, Sensor 2) PNs 68085740AA, or 68197109AA, please file claim under LOP 250810. If for the Engine Out NOx Sensor (Bank 1, Sensor 1) use LOP 250809.

stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

&Rear Door

Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.

Before replacing the blower motor please call one of these individuals:~ First call Brad Bartkowicz at cell (586) 808-4114~ If no answer, then call Vince Celli at cell (586) 630-8136~ If not response in 15 minutes, continue with repair.

Before replacing any of the part numbers listed above, please call any of the following people for each vehicle type. (If you don't get an answer within 15 minutes,then proceed with the repair.):~ WD/WK--68224166AB - Front Ken Deneau, cell (248)-765-0288~ 68089094AA - Rear Pat Presti- cell (248) 379-0972~ KL/UF/PF- 68223053AB, 68225055AA Mark Ware, cell (248) 705-3469~ F500- 68093422AB,Matt Sasina, cell (248)-464-4982 or Bryan Bremer cell (248) 429-9014~ RT- 68029719AB - Front, Matt Filipkowski cell (248) 877-9106~ 05183147AA - Rear, Ken Deneau, cell (248)-765-0288

Engineering would like to have both parts returned for analysis. Also, please take a picture of the parts and email the picture, a short discription of the issue, and the last 8 digits of the VIN to Brigitte.Wicks@fcagroup.com. Thank you.

Before replacing the compressor call FCA Release Engineer Mark Briolat at cell (248) 345-0127. If no response in 15 minutes, continue with the repair.

intermittent by driving under heavy throttle will produce a C1494-92 DTC, if yes, please call FCA axle engineering and do not replace the PTU. Bruce Michel at cell (248) 260-8641, or Jian Zhu at cell (248) 379- 1132. If neither answers with 15 minutes then proceed with the repair. ~ If the service 4WD light lamp is on steady then replace the Power Transfer Unit.

information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com

Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data.

If the power steering pump is being replaced because the power steering fluid flow or pressure readings are below specification, the power steering fluid reservoir and cap assembly should also be replaced. Power steering reservoir and cap assembly 52126151AG or later should be used.

or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U1421 - Implausible Ignition Key Off Time Received. ? P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? 68RFE Transmission Shift Quality Improvements for low speed First to Neutral and Neutral to First (Garage Shifts). ? Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). ? Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. ? Cold idle speed stability improvement. ? Charging system improvements for dual alternator applications. ? Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). ? Fuel Filter Minder calibration changes. ? wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.

The customer may experience a Malfunction Indicator Lamp (MIL) illumination while driving on rough roads. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0300 - Multiple Cylinder Misfire ? P0301 - Cylinder 1 Misfire ? P0302 - Cylinder 2 Misfire ? P0303 - Cylinder 3 Misfire ? P0304 - Cylinder 4 Misfire ? P0305 - Cylinder 5 Misfire ? P0306 - Cylinder 6 Misfire ? P0307 - Cylinder 7 Misfire ? P0308 - Cylinder 8 Misfire

During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present. ? U0140 Lost Communication With Body Control Module. (Attempting to clear this DTC will be unsuccessful.) ? P030X Cylinder X Misfire Detected ? P0300 Multiple Cylinder Misfire Detected Additionally the following enhancements have been implemented. ? Potential small improvement in fuel economy at higher altitudes. ? Potential improvement in high altitude engine idle RPM stability.

with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For The Following Diagnostic Trouble Codes (DTCs): ? U3017 - Control Module Timer/Clock Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P2281 - Air Leak Between MAF And Throttle Body. Other Software Improvements: ? Fuel Filter Minder calibration changes. ? wiTECH Fuel Pressure Override and Fuel System Run Up test improvements. ? EGR system improvement to help prevent freeze up. ? Diesel Exhaust Fluid (DEF) system enhancement during stationary regeneration.

Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

following information to be shared with the engineer. All Active and Inactive P-Codes~ - Refractometer concentration~ - WiTech Concentration~ - WiTech Concentration Sensor Temperature ~ - Urea Tank Temperature~ - Urea Tank level when fault was set~ - Hydrocarbon reading~ - Known fill history before and after the fault was set~ - Recent weather conditions in the area~ - Actions Taken since vehicle had been brought to the dealership ~ Please contact Gary Pleyte at cell (248) 705-3567 or Makenna Coe Smith at cell (248) 202-7545 with the above information. If you are unable to get a response within 15 mins, please continue with the repair according to the trouble tree for P207F.

stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). U110E - Lost Ambient Temperature Message. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: **Ambient Air Temperature Improvements. 68RFE Transmission Overall Shift Quality Improvements.** SCR Efficiency scan tool test improvement. Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. Cold idle speed stability improvement. Charging system improvements for dual alternator applications. Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). Fuel Filter Minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.

(ECM) with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel.

Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

Suspect stock of part number: 04627694AAmust be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before17 April, 2017.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

4720271 to arrange for Fastrac shipper

A customer may describe the following: **Cluster stays awake after ignition is turned off for 10 minutes or more.** False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

converter build date and if necessary, replacing the torque converter. A small number of torque converters were manufactured with the oil grooves on the internal friction discs too wide. This may result in the transmission slipping under heavy loads causing premature wear.

Control Module/Powertrain Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel.Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: P2281 - Air Leak Between MAF And Throttle Body. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance.Other Software Improvements: Charging system improvements for dual alternator applications. Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only) Fuel Filter Minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements

Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). U110E - Lost Ambient Temperature Message. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: NOx sensor calibration improvements. (Sales Code DG7). Enhanced software for a No crank/No start issue. (U0100 - Lost Communication With ECM/PCM). (Sales Code DG7).** Ambient Air Temperature (AAT) improvements. 68RFE Transmission overall shift quality improvements. SCR Efficiency scan tool test improvement. Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. Cold idle speed stability improvement. Charging system improvements for dual alternator applications. Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). Fuel Filter Minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.

Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed.

A small number of customers may experience one or more of the following: ? **?Navigation Failed? message is displayed. ? Navigation is inoperative or inaccurate. ? CD player will not play songs and/or locks up the radio. ? The clock will not automatically update to local time. ? The clock may be off by several hours (RA3 only). ? HVAC temperature out of sync with radio display (KL vehicles). ? Some Uconnect App remote commands do not execute with the vehicle. ? Radio Apps are inoperative. ? Radio will lock up. Radio display screen is black or blank. Battery drain due to radio staying on.** Rearview Camera image appears jittery (UF vehicles only). Inability to establish a WiFi connection when security feature is enabled (UF vehicles only). Audio distortion/popping heard while playing Apple devices through the USB port (UF vehicles only). Remote Uconnect Apps functions (i.e. door locks, remote start) inoperative while the engine is running (UF vehicles only). HVAC temperature out of sync with radio display (KL vehicles). Intermittently blind spot chime will not turn off (KL vehicles only). The radio may switch from SiriusXMT to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Audio muted after AUX device is disconnected. In addition, the following Improvements are included: **Adds Apple SiriT Eyes Free capability for iPhoneT owners. Add the ability to drag and drop icons into the menu bar. Auto Play can now be configured. Enhanced VR performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (YelpT, PandoraT, AhaT, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature.**

If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance.** P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P0307 - Cylinder 7 Misfire. P0308 - Cylinder 8 Misfire.

contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

A customer may describe the following: Cluster stays awake after ignition is turned off for 10 minutes or more. False message ?Battery Voltage Low - Start Engine to Change Ride Height? which appears in the Electronic Vehicle Information Center (EVIC). This condition may occur when the vehicle is first started and the suspension is switched from alternate trailer ride height to normal ride height.

If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

P0542, please replace the Intake Heater Grid and Relay as a set. 68210071A$ (relay) and 05187880A$ (grid). Inspect electrical cable between the heater grid and relay for signs of possible overheating. Replace cable as necessary.

with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. NOTE: There will be a choice between two calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs): **P20EE - Selective Catalytic Reduction (SCR) NOx Catalyst Efficiency Below Threshold - Bank 1 (For ammonia sensor equipped vehicles).** P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia sensor deleted systems only). P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. U110E - Lost Ambient Temperature Message. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. U3017 - Control Module Timer/Clock Performance. U1421 - Implausible Ignition Key Off Time Received. P2281 - Air Leak Between MAF And Throttle Body. Other Software Improvements: Ambient Air Temperature Improvements. Operational Improvement for Dual Alternators. Selective Catalytic Reduction (SCR) Efficiency scan tool test improvement. Fuel Filter Minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements. Exhaust Gas Recirculation (EGR) system improvement to help prevent freeze up. Diesel Exhaust Fluid (DEF) system enhancement during stationary regeneration.

thread damage to the oil filter connector (Spud), DO NOT replace the entire adapter assembly. The oil filter connector is available separately (Part Number 04429355).~ If ordering an adapter due to some other issue, you must also order an oil bypass valve Mopar Part # 04797726AB, as these are not reusable. Please refer to all applicable published service information for oil bypass valve installation

vehicle to listen for audible ?drone? noise at approximately 2,000 RPM. If drone noise is verified, normal torque converter replacement should be performed. The customer may describe a ?heavy droning noise? coming from the vehicle at an engine speed range of 1,800 RPM to 2,000 RPM with mid to deep throttle applied.

Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair."

available software.

the following: **Cluster stays awake after ignition is turned off for 10 minutes or more.** False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.

SYMPTOM/CONDITION: A customer may describe the following: **Cluster stays awake after ignition is turned off for 10 minutes or more.** False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.

MALFUNCTION INDICATOR LAMP ILLUMINATION. PROCEDURE ON REPROGRAMMING POWERTRAIN CONTROL MODULE WITH LATEST SOFTWARE *CN

BULLETIN INFORMATION REGARDING KNOCKING NOISE COMING FROM THE ENGINE AFTER VEHICLE SITTING OVERNIGHT. ENGINE REPLACEMENT IS REQUIRED. *LJ

this is normal and not a defect.

This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2023 to 2013 HD Trucks. The following information is intended to eliminate confusion.

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

semi and full synthetic oils.

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

Detected Message

Cummins used in the 2019 and newer HD Trucks. The following information is intended to eliminate confusion.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

The customer may describe a vibration feeling during a fast launch from 0 mph (0 kph) to 11 mph (18 kph) and the vehicle hauling a heavy load. This vibration is most noticeable at a launch from a stop, at Wide Open Throttle (WOT) while towing a heavy trailer.

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

MasterShield Products in stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers: 82212074, 82212075, 82212076, 82212077, 82212078, & 82213598 . Please return suspect parts back to your facing depot using Return Code 02, before 18 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all suspect stock of following part number: 05026886AJ. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 02 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

If no response is received within 15 minutes, then proceed with required repair.

Call Mike Wicker at cell (248) 821- 9350 with the Fault Code, so we can determine true root cause. If your call is not returned within 15 minutes, please continue with the repair

covers and seat cover repairs.

Please return all stock of part number 68288760AA. Replacement part number is 68288760AB. Replacement parts w ill be available w eek ending 5/6/16. Please return suspect parts back to your facing depot using Return Code 02, before 26 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 68003062AB, 68003083AB, 68003085AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 1PE001W 7AB, 1PE011W 7AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

As per regulatory compliance: Please return follow ing stock of part numbers: 82214711, 82214712, 82214713, 82214714, 82214715, 82214716, 82214717, 82214718, 82214720, 82214721, 82214722, 82214723, 82214724, 82214725, 82214726, 82214727, 82214728, 82214729, 82214730, 82214731, 82214732. Please return parts back to your facing depot using Return Code 02, before 31May, 2016.

Please return suspect stock of following part numbers: 68050625AA, 68050626AA, 68050627AA, 68050628AA, 68050743AA, 68050744AA, 68050839AA, 68050841AA, 68257133AA, 68257134AA, 68264578AA, 68264579AA, 68264580AA, 68264581AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 April, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return parts which have a pacakging date code of July 20th 2016. Reference pictures attached for suspect part identification. Please return parts backto your facing depot using Return Code 02, before 31 August, 2016.

Please return suspect stock of part number 68143886AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 68174065AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 68141880AH, 68141881AH, 68145625AI, 68145626AI, 68189480AF and replacement part numbers are 68141880AI, 68141881AI, 68145625AJ, 68145626AJ & 68189480AG respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 05278632AF and replacement part number is 52030379AA which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 1YG06JSCAC, 1YG06KEPAC, 1YG 06KFSAC, 1YG 06KGZAC, 1YG 06KBUAC and replacement part numbers are 1YG 1YG06KFSAD, 1YG 06KG ZAD, 1YG 06KBUAE respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 68188889AE and replacement part number is 68188889AF which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of following part numbers: 68036213AA, 68036230AF, 68158196AC, 68158197AD, & 68158454AD. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allstock of following part numbers:68241568AB,68241568AC,68241569AB,68241569AC, 68241570AB,68241571A.Replacement part numbersare 68241568AD,68241569AD,68241570AD,68241571AD, which are in stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

This same month last year we had over 40,000 open aged > 5 days tickets. As a result of focused efforts to verify vehicles are repaired and close tickets the number is now at just under 7,000 tickets.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

being opened or closed.

SYSTEM *CN

SEE DOCUMENT SEARCH BUTTON FOR OWNERS LETTER. *LJ

Line Heater Control Circuit High, and U11C1 Reductant Control Module Received Implausible Data From ECM/PCM, Set

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

NOx Sensor Diagnostic Trouble Codes (DTCs) Diagnosis Information.

A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous cameras image before displaying the current image.

A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.

the tank and if necessary, replacing the DEF pump module. A small number of customers may comment that their DEF level gauge is stuck for long periods of time or is erratic. The customer may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High.

The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.

Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.

damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory.

To verify proper functionality, turn on the ignition with no cables or devices plugged into the port. Connect a charging cable to the port, then connect the device. If the device receives power, the port is functioning to design. There are some minor compatibility issues with some charging cables including Apple Lightning cables. For questions regarding the charging port functionality, please call Dave Diovardi at Cell (248) 941-8704 or Rick Gordon at Cell (248) 630-6281.~

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.

Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.

Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find the following Diagnostic Trouble Code may have been set: ? C1556-14-Ride Height Air Pressure Sensor - Circuit Short To Ground Or Open In addition to the DTC listed above, customers may also experience one or more of the following conditions: ? Auto Level Rear Air Suspension does not operate.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory.

A customer may experience, one or more of the following conditions: ? Radio may reset, turn itself off and then back on again. All Symptom Listed Below Are For 2013 Vehicles Only: ? Radio may be muted. Any of DTCs B1400-92-Front Left Audio Speaker Output - Performance Incorrect Operation and/or B1404-92- Front Right Audio Speaker Output - Performance Incorrect Operation and/or B1408-92-Rear Left Audio Speaker Output - Performance Incorrect Operation and/or B140C-92-Rear Right Audio Speaker Output - Performance Incorrect Operation, maybe active or stored. ? Radio display screen may turn off. ? Radio will stay on after the vehicle is turned off with remote. (Applies to vehicle with Mopar remote start add on package only). ? Radio will stay on for 20 minutes after ignition is turned off and the only way to turn off the radio is by pressing the power button on the radio. Software was updated to have the radio shut off based on the cluster accessory delay setting.

The customer may describe LED Turn Signals do not properly display.

(VSIM) with the latest available software. Customers may notice uplift components connected to the VSIM inoperative at times. This is caused by a condition where as the VSIM locks up and becomes unresponsive. No DTCs will be reported for loss of communication between the VSIM and Central Body Controller (CBC). This can be corrected by updating the VSIM with the latest available software. SYMPTOM ONLY FOR 2013 DD AND DP with Power Take Off Prep (Sales Code LBN) Customers may experience after 30 minutes of operation the PTO may shut off. The PTO will start working again after the ignition is cycled.

identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68260866AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 68085880AD, 68085880AF, 68085881AE, 68085881AF, 68085881AG. Replacement part numbers are: 68085880AG, and 68085881AH. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

are receiving this email as you have been identified to have stock on hand or have stock in transit to your dealership. Reports of dealers receiving incorrect fuel pressure sensors packaged as 68210332AA. Correct and suspect parts can be identified visually by the color of the label on the sensors. Correct sensors have white color label on the part whereas the suspect sensors have yellow colored labels. Reference pictures attached for visual identification. Please inspect stock on hand and return any suspect parts found back to your facing PDC using MRA code 02. Replacement parts can be obtained by reordering the same part number. Direct all questions via email to vn83@chrysler.com

A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may lock up. ? Back up display may not turn off. ? Audio mutes. ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud (Grand Cherokee only). ? U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only). Improvements: ? Only allow vehicle settings to be changed in run mode. To help ensure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.

The radio should not be replaced for this issue if the fault is stored, if the code cannot be reproduced and no trouble can be found (radio functions properly). In this case it is no impact to the customer in any way. Do NOT replace the radio for this issue. Please contact John Carlesimo at cell (248) 941-8756 if you have any further questions regarding this fault.

contact Michael Wang at cell (248) 701-5351. If no response or contact is made within 15 minutes, proceed with repairs as necessary.

Please identify battery with the last 8 VIN digits along with the 15 digit Medtronic code from the GR-8 tester. If no response in 15 minutes, continue with the repair. Battery needs to be held and not turned in for core charges.

A manufacturing defect in the level sensor may have occurred, if the level sensor was built within the time frame listed above. There may be a Malfunction Indicator Lamp (MIL) illuminated. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance. ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High.

the tank and if necessary, replacing the DEF pump module. A small number of customers may comment that their DEF level gauge is stuck for long periods of time or is erratic. The customer may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High.

The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.

The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds, and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.

A customer may experience one or more of the following: ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud (Grand Cherokee only). ? U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only). Improvements: ? Only allow vehicle settings to be changed in run mode. To help ensure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.

Control Module (PCM) with updated (latest available) software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:

have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016.

Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory.

Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017.

A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

connector(s) on a 2015-2016 model year 5.7L Hemi DS, D2, DD, DJ or DX truck, please call Lou Nigro at cell (810) 293-3858. If no response is received within 15 minutes, please continue with repair.~

Mirror Contacts Door Window Glass In The Folded Position.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

**This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

information prior to repairing the vehicle. Please contact Jim Smith via Cell Phone (248) 765-8972 If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

**This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**

industry awareness regarding the recommended usage of Authentic Mopar Glass.

identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 05182600AC. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock,or have stock in transit to your dealership. Please return all suspect stock of following part numbers:68159725AB,& 68261143AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02,before 27 O ctober,2015. Return any open orders in process too. Direct all questions via email to MO PARQ C@fcagroup.com

LT:04805839AD

To do this, add the LEG (Trailer Tow Mirrors) sales code to the VIN using DealerCONNECT and then performing a vehicle re-configuration using the WiTech tool.~ After Kit is completely installed, perform the following;~ 1. Add LEG sales code to the VIN under the ?Vehicle Option Updates? Found on Dealerconnect~ 2. Update Vehicle Configuration by using the WiTech tool and performing ?Restore Vehicle Configuration.?

you receive kit PN 68315574AA, discard the instruction sheet shipped with the kit and reference TSB 23-001-16 REV. B for correct bumper installation instructions. ~ Note: This only applies to the AA level of the kit

**This bulletin will help prevent a binding or an audible clicking noise in the center console lid. NOTE: Do not attempt to fix a center console lid that has an existing binding or audible condition by adding the bumper.**

stock in transit to your dealership. Please return suspect stock of part number 68160775AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 26 August, 2016.

A)

Please return allsuspect stock of part numbers:68212041AC,68141170AC,55112738AA.See attachmentsfor identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Please return all suspect stock of following part numbers: 57010364AI, 57010365AI, 57010504AJ, 57010505AJ, 68224368AB, 68224369AB. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017.

numbers:55395241AG,55395241AE.Replacement ispart number 55395241AH which isin stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 12April,2017

have stock in transit to your dealership. Please return suspect stock of part number 04589131AG, 04589243AG . See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 7 April, 2016.

The customer may describe a binding or audible clicking condition when the center console lid is being opened or closed.

information prior to repairing the vehicle. Please contact Jim Smith via Cell Phone (248) 765-8972 If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair.

by cycling the upper console lid. Check for a green dot sticker on the back of the console behind the rear panel by the hinge. ~ If the above complaint is verified and the console DOES NOT have a green dot sticker near the hinge (behind the back panel), order kit PN 68315574AA and install per the included instructions. Otherwise continue with the repair. Please reference TSB 23-001-16 Rev. E (or later version).

A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous cameras image before displaying the current image. Navigation lost vehicle position, during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, ? Listen? to text, will only play 1st message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as ?- - ? not normal values.Improvements: High Definition (HD) radio buffering. Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Making assist calls. App functionality and screen displays. Displays correct media, song titles and tracks. Travel Link, Points Of Interest (POI), displaying movies and favorites. Incoming calls, audio enhancements (LA, LD and LX Only). Audio for strong AM stations. VR performance. Settings can only be changed in run mode, not ACC. Notify user when messaging features are not s

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

A small number of customers may experience one or more of the following: **Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles).** Intermittently blind spot chime will not turn off (KL vehicles only). Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, ? Listen? to text will only play first message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as ?- - ? not normal values. Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. Ability to press VR button for more than one second.**

please also replace the fan clutch assembly using current Mopar stock (part number 52014729A$).~ Once installed, contact Christine Donegan at (866) 799-1692 ext 1257 to initiate a fast track request for the return of the parts for analysis.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient tempe

A small number of customers may experience one or more of the following: Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient temperature as ?- - ? not n

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

the following scenario occurs; The T79 or U11 recall was completed where the shifter inspection was acceptable and the software flash was performed but then the customer comes back needing the BTSI bracket replaced for coming out of park without the brake or key.

A small number of customers may experience one or more of the following: ? Blind Spot module beep or chime sound may be heard continuous (KL Only). ? Radio may keep the CAN bus network awake, causing a battery drain. ? Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. ? Not possible to set temperature in degree C using the VR (UK vehicles only). ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? Voice Recognition (VR) operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? Voice Recognition (VR) phone button may not work at times. ? Audio muted after AUX device is disconnected. ? Voice Recognition (VR) , ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Displays correct media, song titles and tracks. ? Incoming calls, audio enhancements (LA, LD and LX Only). ? Audio for strong AM stations. ? VR performance. ? Settings can only be changed in run mode, not ACC. ? Notify user wh

If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any DTCs identified with the scan tool and document them on the repair order.

check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.

A small number of customers may experience one or more of the following: ? Intermittently blind spot chime will not turn off (KL vehicles only). ? Enable High Definition (HD) feature, (RA4 radios located in Canada and Mexico). ? Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). ? The Radio may switch from SiriusXM to an AM station by itself. ? Uconnect registration always present, can not remove Uconnect account. ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? VR operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? VR phone button may not work at times. ? Audio muted after AUX device is disconnected. ? VR, ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? SirusXM station information does not update. ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Faster response time when using the Remote Service App (U.S. market only). ? Faster connection time with 911(U.S. market only). ? Keyboard improvements, in the Points Of Interest (POI) section. ? High Definition (HD) radio buffering. ? Spanish translation. ? Radio station, scroll feature. ? D

A small number of customers may experience one or more of the following: ? Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. ? Not possible to set temperature in degree C using the VR (UK vehicles only). ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? Voice Recognition (VR) operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? Voice Recognition (VR) phone button may not work at times. ? Audio muted after AUX device is disconnected. ? Voice Recognition (VR) , ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Displays correct media, song titles and tracks. ? Incoming calls, audio enhancements (LA, LD and LX Only). ? Audio for strong AM stations. ? VR performance. ? Settings can only be changed in run mode, not ACC. ? Notify user when messaging features are not supported on certain phones/devices. ? Shows direction and distance for POI when using VR.

A small number of customers may experience one or more of the following: ? Enable High Definition (HD) feature, (RA4 radios located in Canada and Mexico). ? Keyboard improvements, in the Points Of Interest (POI) section. ? Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). ? The Radio may switch from SiriusXM to an AM station by itself. ? Uconnect registration always present, can not remove Uconnect account. ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? VR operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? VR phone button may not work at times. ? Audio muted after AUX device is disconnected. ? VR, ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? SirusXM station information does not update. ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? High Definition (HD) radio buffering. ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Making assist calls. ? App functionality and screen displays. ? Displays correct media, song titles and tracks. ? Travel

please also replace the fan clutch assembly using current Mopar stock (part number 52014729A$).~ Once installed, contact Christine Donegan at (866) 799-1692 ext 1257 to initiate a fast track request for the return of the parts for analysis.

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

insert on about 4,300 vehicles may not have properly adhered to the metal shifter housing during the shifter manufacturing process. This condition could cause looseness in the gear shift lever, noise, and additional effort to move the shifter into the selected gear. The manual transmission shift lever must be replaced on all involved vehicles.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only) The Radio may switch from SiriusXM to an AM station by itself Uconnect registration always present, can not remove Uconnect account Teleprompter does not appear when pressing the Voice Recognition (VR) button VR operation cancels while in media mode Radio may display previous cameras image before displaying the current image Navigation lost vehicle position, during route calculation Navigation displays are missing after vehicle heading changes Navigation giving incorrect guidance to exit the highway FM audio may switch to AM after ignition cycle Text messages appear as sender?s phone number not their name. VR phone button may not work at times Audio muted after AUX device is disconnected VR, ? Listen? to text, will only play 1st message Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only) SirusXM station information does not update. Speed adjusted volume, may not work AM or FM seek or tuner soft keys may be missing Display screen show ambient temperature as ?- - ? not normal values.Improvements: High Definition (HD) radio buffering. Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Making assist calls. App functionality and screen displays. Displays correct media, song titles and tracks. Travel Link, Points Of Interest (POI), displaying movies and favorites. Incoming calls, audio enhancements (LA, LD and LX Only). Audio for strong AM stations. VR performance. Settings can only be changed in run mode, not ACC.

A small number of customers may experience one or more of the following: Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles).** Intermittently blind spot chime will not turn off (KL vehicles only). Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender's phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, Listen, to text will only play first message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as ?- - ? not normal values. Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. Ability to press VR button for more than one second.** Faster response time when using the Remote

A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display cameras previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as senders phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR Listen to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing.

Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?

number of customers may experience one or more of the following: Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient temperature as ?- - ? not normal values. Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect.Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. HVAC temperature out of sync with radio display (KL Only).** Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Displays correct media, song titles and tracks. Incoming calls, audio enhance

PLEASE ALSO REPLACE THE FAN CLUTCH ASSEMBLY USING CURRENT MOPAR STOCK (PART NUMBER 52014729A$).~ ONCE INSTALLED, CONTACT CHRISTINE DONEGAN AT (866) 799-1692 EXT 1257 TO INITIATE A FAST TRACK REQUEST FOR THE RETURN OF THE PARTS FOR ANALYSIS."

Diesel Exhaust Fluid (DEF) System Diagnostic Trouble Codes (DTCs) due to Hydrocarbon Contamination.

2019 RAM 3500 Pickup (D2)

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P218F - Reductant No Flow Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. The customer will not notice any drivability issues associated with these DTCs. These DTCs may set when the vehicles is parked for a long time and the ambient temperatures are below -11 C (12 F).

guidelines.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 68146401AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock, or have stock in transit to your dealership. Please return following part numbers: CBTTP57FAA, & CBTTP57FAB. Replacement part number CBTTP57FAC will be available week beginning 26 O ct., 2015. There are reports of pre-programmed FO BS in these kits, preventing dealer pairing of W IN and Transmitter Key FO BS. If repair is needed prior to new part availability, order two of part number 05026886AK transmitter Integrated Key FO B. Please return suspect parts back to your facing depot using Return Code 02, before 06 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

(248) 622 8109 ~ Mexican Dealers please call Ricardo Lozada at cell +52 1 55 1370 3187. If no return call in 15 minutes, continue with repair.

please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair.

A customer may experience one or more of the following conditions: Radio display screen will lock up and reset intermittently. Incorrect routing directions to fuel stations when using Travel Link. Unable to turn on heated seats; icon is greyed out. Navigation screen goes blank. Navigation system freezes/locks up. Vehicles with Mopar special edition radio will update radio?s splash screen. Navigation icon shows the vehicle going backward when it?s moving forward.

stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

guidelines.

Please return allsuspect stock of part numbers:68148794AH,68148794AF,68148794AD,68156453AH,68156453AF, 68156453AD,68161542AE,68161542AD.See attachment for identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

18.01.35 (BU Vehicles)

The customer may notice that the Uconnect Access feature is inoperative. Pressing either button (Assist or 9-1-1) on the rear view mirror will not activate that feature.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

Creating a Star case and recording the MDN and MEID with in the Star Case. The Star center will reply back with an access code that will need to be entered into the radio. The customer may notice that their Uconnect Apps do not work and they can?t register with Uconnect.

The customer may describe a lack of the audible chime during the use of the Park Sense Rear Park Assist system.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

The customer may notice that the Uconnect Access feature is inoperative. Pressing either button (Assist or 9-1-1) on the rear view mirror will not activate that feature.

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

updating the radio software.

BULLETIN INVOLVES INSPECTING AND UPDATING RADIO SOFTWARE *CN

APPEAR WHEN VOICE RECOGNITION (VR) BUTTON IS PRESSED, BLIND SPOT CHIME INTERMITTENTLY FAILS TO TURN OFF, PREVIOUS RADIO CAMERA IMAGE IS DISPLAYED BEFORE CURRENT IMAGE. MODEL 2015 CHARGER, RAM 4500, 5500, RAM 3500, 2500, 1500 PICKUP, VIPER, CHEROKEE, CHALLENGER, GRAND CHEROKEE, DURANGO, CHRYSLER 300. *PE

CUSTOMERS ARE NOT ABLE TO CHANGE TEMP. OF HEATED SEATS , RADIO NOT ALLOWING SELECTION OF PROPER LANGUAGE, RADIO FANS CONTINUE TO RUN AT HIGH SPEED. *LJ UPDATED 10/13/15. *PE

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure.

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

The customer may describe the Electronic Stability Control (ESC) Warning lamp is illuminated on the instrument cluster. Upon further inspection, the technician may find the following Diagnostic Trouble Code (DTC): C006A-49 - Multi-Axis Acceleration Sensor - Internal Electronic Failure.

code), do NOT replace the rotor for a clicking noise occuring while turning at low parking lot speeds. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub mounting face) with a Scotch Brite Pad or equivalent, and re-assemble.~

Start Date: 10/27/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of part numbers: 68144663AA, 52013874AE. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to MOPARQC@fcagroup.com

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

REPROGRAMMING OF THE ABS MODULE SOFTWARE IS HIGHLY RECOMMENDED. *LJ

cover, please verify the wheel cover is properly seated by removing and re-installing. Drive vehicle to verify noise. If noise is present, replace the wheel cover

spare tire winch cable when storing under the vehicle. The adapter is part number 6824863AA and requires three (3) mounting nuts; PN 68150129AA.

Please return stock of part number 68103256AG packaged before 2016/08/01. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

A test-drive snap shot may help you isolate the source of the issue.

WARRANTY WHICH ONLY APPLIES TO 2013-2014 MODEL VEHCLES. *LJ

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

The customer may experience when exiting a dark parking structure or dark tunnel the auto headlamps may not turn off. The customer may also experience when driving on an over cast day the auto headlamps may cycle on and off frequently.

Please return suspect stock of following part numbers: 68110016AC, 68110016AD, 68110016AE, 68110017AD, 68236104AC, 68236105AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31 August, 2016.

INFORMATION REGARDING AUTO HEADLAMP ENHANCEMENTS, CHECKING TUNNEL DETECTION VALUES AND PERFORMING A VEHICLE RECONFIGURATION IF NEEDED. *LJ

drag link replacement ensure that the welded draglink toe setting procedure has been followed first. ~ ~ Service Library: 02 - Front Suspension / Wheel Alignment / Standard Procedure / TOE SETTING PROCEDURE FOR TRUCKS WITH DRAG LINK RECALL WELD ~

A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.

A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.

as either having stock, or have stock in transit to your dealership. Please return all suspect stock of follow ing part number: 68245351AB. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may be locked. ? Backup display may not turn off. ? Audio Mutes. ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud. ? The radio does not allow selection of the Polish language. ? The radio fan continually runs at high speed. ? Customer perception may be the radio fan is too loud. Improvements: ? Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.

A customer may experience one or more of the following: ? Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. ? Touchscreen confirmation beep may be too loud. ? The radio does not allow selection of the Polish language. ? The radio fan continually runs at high speed. ? Customer perception may be the radio fan is too loud. Improvements: ? Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. ? Always gray out text message soft keys for non-supporting devices. ? Voice Recognition (VR) improved accuracy.

A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.

B)

technician an overview of the steps a customer will need to take to complete the update.

If no response in 15 minutes, proceed with ordering the part

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

THE RADIO FREQUENCY ON SOME HUB VEHICLES HAVE SOFTWARE PROBLEMS THAT CAUSE SLOW KEYLESS ENTRY RESPONSE. *LJ