2014 Ram 1500 TSBs

Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P2072 - Electronic Throttle Control System - Ice Blockage. ? P2110 - Electronic Throttle Control - Forced Limited RPM. ? P2118 - Electronic Throttle Control Motor Current Performance - Bank 1. The customer may also comment on the following: ? The vehicle may not start (below freezing conditions - typically -7 C (-20 F)) This bulletin involves removing the PCV valve and hose to dry out, drying out the throttle body and installing an updated make-up air hose, air cleaner lid and changing the oil.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a High.

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20F (-29C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse.

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles e

(DTCs) P0299 Turbocharger Underboost And/Or P026D ? Fuel Injection Quantity Higher Than Expected, Set.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

on a 2014-2016 model year 3.0L Turbo Diesel (EXF) DS truck, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair.~

Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.

being replaced due to P249C, P203E, or P24F3 on a 2014-2016 model year 3.0L Turbo Diesel (EXF) on DS or WK, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

installed in the vehicle.

the Charge Air Cooler (CAC) system for excessive water and/or ice and drying the CAC components if needed. It also involves installing a winter front cover. A small number of customers may experience a MIL illumination when ambient temperatures fall below 32F (0 C). Upon further inspection, a technician may find the ? P0299 - Turbocharger Underboost Condition ? U1424 - Implausible Engine Torque Signal Received In addition, a customer vehicle may come in with a no crank/no start. This may have occurred after the vehicle has been driven for an extended period of time in extremely low ambient and then allowed to sit overnight. Further diagnosis may indicate a possible inoperative starter. A possible cause of these concerns may be contributed to internal icing of the Charge Air Cooler (CAC) system and intake manifold. Icing will occur because warm, moist air from the turbo charger is being rapidly cooled and the moisture is then condensed into liquid by the CAC. The liquid is then distributed into the rest of the intake system, which is operating at ambient temperature, where it will then freeze. Vehicles that are driven for extended periods of time are susceptible to higher amounts of ice build up within the intake manifold. Once the vehicle is turned off and allowed to sit, the ice formation in the intake will begin to melt due to the elevated underhood temperatures. The moisture will then run down the intake runners and accumulate in the combustion chamber through an open intake valve causing the engine to hydro-lock. To help prevent icing in the CAC system when the vehicle is operated in low ambient temperatures, it is highly recommended that the vehicle have winter front cover installed. This raises the CAC outlet temperatures above freezing which will help reduce condensation build up.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Module (PCM) with latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary, depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC) other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which technician may find one or more of following DTCs have been set: P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. P2459-00 - Diesel Particulate Filter Regeneration Frequency. P0133-00 - O2 Sensor 1/1 Slow Response. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). P0171-00 - Fuel System 1/1 Lean. P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). P0045-00 - Turbocharger Boost Control Circuit/Open. P0087-00 - Fuel Rail Pressure Too Low. P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. P0128-00 - Thermostat Rationality. P0234-00 - Turbocharger Overboost Condition. P0420-00 - Catalyst Efficiency (Bank 1). P05F8-00 - Reductant Heater Control Module Performance. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P200A-00 - Intake Manifold Runner Performance - (Bank 1). P200B-00 - Intake Manifold Runner Performance - (Bank 2). P202E-00 - Reductant Injection Valve Circuit Performance. P204F-00 - Reductant System Performance. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P20BA-00 - Reductant Heater 1 Control Circuit Performance. P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. P20C2-00 - Reductant Heater 3 Control Circuit Performance. P20E9-00 - Reductant Pressure Too High. P225C-00 - NOX Sensor 1/1 Performance - Signal Stuck High.

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20F (-29C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB)

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

reprogramming of the Transmission Control Module (TCM) with new software. Customers may indicate that the vehicle remains in first gear too long after the engine restarts with the Stop/Start feature.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

A small number of customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition.

reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0335-00 - Crankshaft Position Sensor Circuit. P0336-00 - Crankshaft Position Sensor Performance. Customers may also comment on one or more of the following: The vehicle will not accelerate quickly over 80 kph (50 mph) (vehicle is in limp mode). Vehicle periodically stalls.This symptom/condition is caused from missing magnetic material on the crankshaft tone wheel

(Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (Sales Code ERB). **U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).** Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (Sales Code EZH). **U0140 - Lost Communication With Body Control Module (attempting to clear this ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).** System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -29C (-20F). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (Sales Codes EZC or EZF). U0140 - Lost Communication With Body Control Module (attempting to clear this Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination wi

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-

the 2014-15 MY Ram 1500 Pick-up with a rear axle manufactured within the October to November 2014 calendar year. Please contact Ridhan Riyal at cell (810) 513-3832 for further instruction. If he cannot be reached with 15 minutes proceed with your repair.~ The DS Limited Slip Differential operates as a torque sensing device because when torque is applied to the differential gear set the reaction forces of the bevel gears apply an axial force into the clutch system providing the torque bias. When the input torque is very low the reaction forces will decrease allowing the differential to ACT SIMILIAR TO A OPEN DIFFERENTIAL (zero preload). Please do not confuse this with prior model year Limited Slip Differentials. See the service manual for complete details.

Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

When installing the replacement engine, you will need to transfer the engine wiring harness from the original engine onto the new assembly. Refer to STAR Online S2209000003 for detailed instructions.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.

Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.

(Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~

on a 2014-2016 model year 3.0L Turbo Diesel (EXF) DS truck, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair.~

the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.

the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.

the correct procedure for changing an oil filter on a 3.0L diesel to prevent engine damage. The bulletin also highlights the design differences in the oil filter cartridges used in the GEN-2 and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

in the oil filter cartridges used in the GEN-2, and GEN-3 3.0L diesel. As well as potential issues that can arise should the incorrect filter be used in each application. Although similar in design, the oil filter cartridges used on the GEN-2 and GEN-3 3.0L diesel engines are different in design. Interchanging them may result in premature engine damage over time.

Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (sales code ERB). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (sales code EZH). * System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20F (-29C). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC or EZF). * U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). * Transmission torque management enhancement when shifting from drive to reverse. * Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. * Improved tran

Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience an intermittent engine shudder, bucking under hard acceleration, or vibration. In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P1296-00 - EGR Slow Response - Increasing Flow. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ? P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOx Sensor 1/2 Zero Offset Too Low. ? P2463-00 - Diesel Particulate Filter - Soot Accumulation . ? U0422-00 - Implausible Data Received From Body Control Module. ? U3017-00 - Control Module Timer/Clock Performance. ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel

A small number of customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition. DISCUSSION: The root cause of the engine shudder has been found to be due to excess carbon build-up on the exhaust valve stems and will typically happen on vehicles driven mostly in light load conditions. As a result, new cylinder heads have been released that are equipped with newly designed valve stem seals. These newly designed seals are designed to help prevent excessive carbon from building up on the valve stems. Although it may be hard to reproduce, engine shudder resulting from these excess carbon deposits, will typically only happen under the following driving conditions: ? Steady speeds between 50 and 70 mph (80 and 113 kph). ? Engine speed between 1600 - 2000 RPM. ? Present during engine warm up to operating temperature after a cold soak. ? Only present for a few seconds at a time and often during a 6-7 upshift. ? Light load acceleration or while driving up a slight grade. ? Symptom will go away either by aggressively applying the accelerator pedal or going into a zero throttle deceleration.

Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-

stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

above vehicles, located between the turbocharger and the diesel particulate filter/converter assembly, may fracture due to fatigue and cause an exhaust leak. The exhaust down pipe with the high frequency decoupler must be replaced. Models

&Rear Door

Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.

Before replacing the blower motor please call one of these individuals:~ First call Brad Bartkowicz at cell (586) 808-4114~ If no answer, then call Vince Celli at cell (586) 630-8136~ If not response in 15 minutes, continue with repair.

Before replacing any of the part numbers listed above, please call any of the following people for each vehicle type. (If you don't get an answer within 15 minutes,then proceed with the repair.):~ WD/WK--68224166AB - Front Ken Deneau, cell (248)-765-0288~ 68089094AA - Rear Pat Presti- cell (248) 379-0972~ KL/UF/PF- 68223053AB, 68225055AA Mark Ware, cell (248) 705-3469~ F500- 68093422AB,Matt Sasina, cell (248)-464-4982 or Bryan Bremer cell (248) 429-9014~ RT- 68029719AB - Front, Matt Filipkowski cell (248) 877-9106~ 05183147AA - Rear, Ken Deneau, cell (248)-765-0288

Engineering would like to have both parts returned for analysis. Also, please take a picture of the parts and email the picture, a short discription of the issue, and the last 8 digits of the VIN to Brigitte.Wicks@fcagroup.com. Thank you.

Before replacing the compressor call FCA Release Engineer Mark Briolat at cell (248) 345-0127. If no response in 15 minutes, continue with the repair.

intermittent by driving under heavy throttle will produce a C1494-92 DTC, if yes, please call FCA axle engineering and do not replace the PTU. Bruce Michel at cell (248) 260-8641, or Jian Zhu at cell (248) 379- 1132. If neither answers with 15 minutes then proceed with the repair. ~ If the service 4WD light lamp is on steady then replace the Power Transfer Unit.

information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com

Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data.

If the power steering pump is being replaced because the power steering fluid flow or pressure readings are below specification, the power steering fluid reservoir and cap assembly should also be replaced. Power steering reservoir and cap assembly 52126151AG or later should be used.

or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com

Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake M

inspecting and securing the AGS actuator motor case housing. The customer may describe the MIL is illuminated. On further inspection the technician may find the following Diagnostic Trouble Code (DTC) P1D73 Active Grill Shutter (AGS) Performance.

Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-

with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine. LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to enable the scan tool based transmission ?Quick Learn.? ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) ? Software to correct a harsh bump feel during a 2-1 downshift. WK vehicles equipped with a 3.6L engine (Sales Code ERB) ? ECO mode will not retain settings. If ECO mode is turned off, it will turn back on after the ignition is cycled. ? Software to correct a harsh bump feel during a 2-1 downshift. DS vehicles equipped with 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. ? Software improvements to powertrain braking in Tow/Haul mode. ? Software to improve downshift response from a medium to heavy pedal acceleration. ? Driveability improvements at higher altitudes. ? Software to improve acceleration during cruise control operation ? Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed inste

the Charge Air Cooler (CAC) system for excessive water and/or ice and drying the CAC components if needed. It also involves installing a winter front cover. A small number of customers may experience a MIL illumination when ambient temperatures fall below 32F (0 C). Upon further inspection, a technician may find the following Diagnostic Trouble Codes (DTCs). ? P0299 - Turbocharger Underboost Condition ? U1424 - Implausible Engine Torque Signal Received In addition, customer vehicle may come in with a no crank/no start. This may have occurred after the vehicle has been driven for an extended period of time in extremely low ambient and then allowed to sit overnight. Further diagnosis may indicate a possible inoperative starter. DISCUSSION: A possible cause of these concerns may be contributed to internal icing of the Charge Air Cooler (CAC) system and intake manifold. Icing will occur because warm, moist air from the turbo charger is being rapidly cooled and the moisture is then condensed into liquid by the CAC. The liquid is then distributed into the rest of the intake system, which is operating at ambient temperature, where it will then freeze. Vehicles that are driven for extended periods of time are susceptible to higher amounts of ice build up within the intake manifold. Once the vehicle is turned off and allowed to sit, the ice formation in the intake will begin to melt due to the elevated underhood temperatures. The moisture will then run down the intake runners and accumulate in the combustion chamber through an open intake valve causing the engine to hydro-lock. To prevent icing in the CAC system when vehicle is operated in low ambient temperatures, it is highly recommended that the vehicle have winter front cover installed. This raises the CAC outlet temperatures above freezing which will help reduce condensation build up.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

inspecting and securing the AGS actuator motor case housing. The customer may describe the MIL is illuminated. On further inspection the technician may find the following Diagnostic Trouble Code (DTC) P1D73 Active Grill Shutter (AGS) Performance.

Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 -

(Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

(Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~

stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (Sales Code ERB). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (Sales Code EZH). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful. ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -29C (-20F). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (Sales Codes EZC or EZF). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination wi

the 2014-15 MY Ram 1500 Pick-up with a rear axle manufactured within the October to November 2014 calendar year. Please contact Ridhan Riyal at cell (810) 513-3832 for further instruction. If he cannot be reached with 15 minutes proceed with your repair.~ The DS Limited Slip Differential operates as a torque sensing device because when torque is applied to the differential gear set the reaction forces of the bevel gears apply an axial force into the clutch system providing the torque bias. When the input torque is very low the reaction forces will decrease allowing the differential to ACT SIMILIAR TO A OPEN DIFFERENTIAL (zero preload). Please do not confuse this with prior model year Limited Slip Differentials. See the service manual for complete details.

Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

Suspect stock of part number: 04627694AAmust be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before17 April, 2017.

B1291-25, B1292-25, B1293-25, B1295-25, B1296-25, B1297-25, and/or B1298-25, check for snow/mud/ice/obstruction and clean the Sensors, both front and back (behind bumper) of sensor. The snow/mud/ice can be behind the bumper, sensor retainer and/or the sensor which may cause customers to think they have an issue since they cleaned the front of the sensor/bumper, but not behind where dirt/mud/ice snow can accumulate. Once the Bumper and Sensors are completely cleaned and clear of snow, mud, ice, and/or obstruction, the sensors must activate in order for the faults to go STORED. After cleaning the Bumper and Sensors, turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED. 2) Active or Stored DTC code of Short to Ground fault: B128E-11, B128F-11, B1290-11, B1291-11, B1292-11, B1293-11, B1294-11, B1295-11, B1296-11, and/or B1298-11, or if you have an active or stored DTC code of Performance or Incorrect Operation fault: B128E-92, B128F-92, B1290-92, B1291-92, B1293-92, B1294-92, B1295-92, B1296-92, B1297-92, and/or B1298-92, then check the wiring behind the sensor. Specifically, ensure that the connector behind the park assist sensor is fully mounted. Ensure also, there is no dirt, corrosion, or damage in this connector behind the park assist sensor as this will also cause a Short to Ground fault. With potential wiring issues addressed, the sensors must activate in order for the faults to go STORED. After all sensors are properly connected (you will likely hear a click once the connector is fully seated on the sensor), turn off the engine, wait 10 seconds, turn on the engine and then place the vehicle in REVERSE so that the sensors activate. The faults will go STORED.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. P2459-00 - Diesel Particulate Filter Regeneration Frequency P0133-00 - O2 Sensor 1/1 Slow Response P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2) P0171-00 - Fuel System 1/1 Lean P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1) P0045-00 - Turbocharger Boost Control Circuit/Open P0087-00 - Fuel Rail Pressure Too Low P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation P0128-00 - Thermostat Rationality P0234-00 - Turbocharger Overboost Condition P0420-00 - Catalyst Efficiency (Bank 1) P05F8-00 - Reductant Heater Control Module Performance P050E-00 - Cold Start Engine Exhaust Temperature Too Low P200A-00 - Intake Manifold Runner Performance - (Bank 1) P200B-00 - Intake Manifold Runner Performance - (Bank 2) P202E-00 - Reductant Injection Valve Circuit Performance P204F-00 - Reductant System Performance P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance P20BA-00 - Reductant Heater 1 Control Circuit Performance P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance P20C2-00 - Reductant Heater 3 Control Circuit Performance P20E9-00 - Reductant Pressure Too High P225C-00 - NOX Sensor 1/1 Performance - Signal Stuck High

(PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20F (-29C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. Software improvements to powertrain braking in Tow/Haul mode. Software to improve downshift response from a medium to heavy pedal acceleration. Driveability improvements at higher altitudes. Software to improve acceleration during cruise control operation Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed instead of U11E3 - TCM Lost communication with ESM On D-PT CAN.WD vehicles equipped with a 3.6L engine (Sales Code ERB)

reprogramming the Powertrain Control Module (PCM) with new software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on codes that have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P20E9-00 - Reductant Pressure Too High.

This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.

reprogramming the Powertrain Control Module (PCM) with new software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on codes that have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P20E9-00 - Reductant Pressure Too High.

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

reprogramming of the Transmission Control Module (TCM) with new software. Customers may indicate that the vehicle remains in first gear too long after the engine restarts with the Stop/Start feature.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition.

contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding.

false message ?Battery Voltage Low - Start Engine to Change Ride Height? which appears in the Electronic Vehicle Information Center (EVIC) when unlocking or locking the doors. A battery drain may happen when using the key fob to stop the vehicle from lowering. The ASCM does not go to sleep and the CAN-C bus stays awake.

reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following (DTCs) have been set:P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible (14&15 MY). P0116 - Engine Coolant Temperature Sensor Performance (14&15 MY). P0335 - Crankshaft Position Sensor Circuit (14&15 MY). U1424-00 - Implausible Engine Torque Signal Received (14&15 MY). P1239 - Engine Oil Temperature Too Low (15 MY Sales Code ERB). P0300 - Multiple Cylinder Misfire.P0456 - EVAP System Small Leak.P0607 - ECU Internal Performance.P2096 - Downstream Fuel Trim System 1 Lean.P2097 - Downstream Fuel Trim System 1 Rich. P2098 - Downstream Fuel Trim System 2 Lean. P2099 - Downstream Fuel Trim System 2 Rich. P1004 - Short Runner Valve Control Performance. P2008 - Short Runner Valve (SRV) Control Circuit. P2016 - Intake Manifold Runner Position Sensor Circuit Low. P2017 - Intake Manifold Runner Position Sensor Circuit High. P26AB - Engine Coolant Bypass Valve Stuck.U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful) (with 4.7L or 3.6L).P0607 - ECU Internal Performance. (with 4.7L).The following improvements are included in this update:Throttle Position Sensor (TPS) calibration (14&15 MY).Corrects a false oil pressure lamp illumination at key on (14&15 MY with 5.7L).Shift quality of the first shift after a few hours of vehicle drivetrain cooling down.Automatic Shut Down (ASD) Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).Charging system voltage regulator control improvements.System improvements to prevent MIL illumination with a DTC P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures grea

Water pumps are found TNF but the water pump bypass o-ring was pinched resulting in a coolant leak that looks like a failed pump. Please inspect the bypass o-ring before replacing the pump as it is available separate for service.

If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

being replaced due to P249C or P203E on a 2014-2016 model year 3.0L Turbo Diesel (EXF) on DS or WK, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair.~

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.

MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. THE FOLLOWING POWERTRAIN SYSTEM IMPROVEMENTS/ENHANCEMENTS ARE INCLUDED IN THIS SOFTWARE RELEASE. THESE ENHANCEMENTS ARE LISTED BY VEHICLE APPLICATION. DS VEHICLES EQUIPPED WITH A 3.6L ENGINE (SALES CODE ERB). **U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (ATTEMPTING TO CLEAR THIS DTC WILL BE UNSUCCESSFUL). ASD RELAY ENHANCEMENTS TO IMPROVE FUEL PUMP RELAY INITIALIZATION AT KEY ON - (AUTO SHUTDOWN).** ENHANCED AUTOMATIC OIL CHANGE INDICATOR (EAOCI) SYSTEM IMPROVEMENTS TO SWITCH TO A SEVERE DUTY CYCLE ALGORITHM ANYTIME THE PCM IS REPLACED TO ENSURE THE CUSTOMER RECEIVES A TIMELY OIL CHANGE REQUIRED MESSAGE. CORRECTED A GENERIC SCAN TOOL DISPLAY ISSUE REGARDING MODE 6 DATA ACCURACY. DS VEHICLES EQUIPPED WITH A 5.7L ENGINE (SALES CODE EZH). **U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (ATTEMPTING TO CLEAR THIS DTC WILL BE UNSUCCESSFUL). ASD RELAY ENHANCEMENTS TO IMPROVE FUEL PUMP RELAY INITIALIZATION AT KEY ON - (AUTO SHUTDOWN).** SYSTEM IMPROVEMENTS TO PREVENT MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION WITH A DIAGNOSTIC TROUBLE CODE (DTC) P0300 - MULTIPLE CYLINDER MISFIRE WHEN USING A BLOCK HEATER IN AMBIENT TEMPERATURES GREATER THAN -29C (-20F). ENHANCED AUTOMATIC OIL CHANGE INDICATOR (EAOCI) SYSTEM IMPROVEMENTS TO SWITCH TO A SEVERE DUTY CYCLE ALGORITHM ANYTIME THE PCM IS REPLACED TO ENSURE THE CUSTOMER RECEIVES A TIMELY OIL CHANGE REQUIRED MESSAGE. CORRECTED A GENERIC SCAN TOOL DISPLAY ISSUE REGARDING MODE 6 DATA ACCURACY. DJ, DD, AND D2 VEHICLES EQUIPPED WITH A 5.7L ENGINE (SALES CODES EZC OR EZF). U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (ATTEMPTING TO CLEAR THIS DTC WILL BE UNSUCCESSFUL). TRANSMISSION TORQUE MANAGEMENT ENHANCEMENT WHEN SHIFTING FROM DRIVE TO REVERSE.

ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR."

THE 2014-15 MY RAM 1500 PICK-UP WITH A REAR AXLE MANUFACTURED WITHIN THE OCTOBER TO NOVEMBER 2014 CALENDAR YEAR. PLEASE CONTACT RIDHAN RIYAL AT CELL (810) 513-3832 FOR FURTHER INSTRUCTION. IF HE CANNOT BE REACHED WITH 15 MINUTES PROCEED WITH YOUR REPAIR.~ THE DS LIMITED SLIP DIFFERENTIAL OPERATES AS A TORQUE SENSING DEVICE BECAUSE WHEN TORQUE IS APPLIED TO THE DIFFERENTIAL GEAR SET THE REACTION FORCES OF THE BEVEL GEARS APPLY AN AXIAL FORCE INTO THE CLUTCH SYSTEM PROVIDING THE TORQUE BIAS. WHEN THE INPUT TORQUE IS VERY LOW THE REACTION FORCES WILL DECREASE ALLOWING THE DIFFERENTIAL TO ACT SIMILIAR TO A OPEN DIFFERENTIAL (ZERO PRELOAD). PLEASE DO NOT CONFUSE THIS WITH PRIOR MODEL YEAR LIMITED SLIP DIFFERENTIALS. SEE THE SERVICE MANUAL FOR COMPLETE DETAILS."

THIS APPLIES TO 3.0L DIESEL ENGINES. *LJ

(DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

MasterShield Products in stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers: 82212074, 82212075, 82212076, 82212077, 82212078, & 82213598 . Please return suspect parts back to your facing depot using Return Code 02, before 18 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all suspect stock of following part number: 05026886AJ. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 02 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com

If no response is received within 15 minutes, then proceed with required repair.

Call Mike Wicker at cell (248) 821- 9350 with the Fault Code, so we can determine true root cause. If your call is not returned within 15 minutes, please continue with the repair

covers and seat cover repairs.

Please return all stock of part number 68288760AA. Replacement part number is 68288760AB. Replacement parts w ill be available w eek ending 5/6/16. Please return suspect parts back to your facing depot using Return Code 02, before 26 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 68003062AB, 68003083AB, 68003085AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part numbers: 1PE001W 7AB, 1PE011W 7AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 24 May, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

As per regulatory compliance: Please return follow ing stock of part numbers: 82214711, 82214712, 82214713, 82214714, 82214715, 82214716, 82214717, 82214718, 82214720, 82214721, 82214722, 82214723, 82214724, 82214725, 82214726, 82214727, 82214728, 82214729, 82214730, 82214731, 82214732. Please return parts back to your facing depot using Return Code 02, before 31May, 2016.

Please return suspect stock of following part numbers: 68050625AA, 68050626AA, 68050627AA, 68050628AA, 68050743AA, 68050744AA, 68050839AA, 68050841AA, 68257133AA, 68257134AA, 68264578AA, 68264579AA, 68264580AA, 68264581AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 April, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return parts which have a pacakging date code of July 20th 2016. Reference pictures attached for suspect part identification. Please return parts backto your facing depot using Return Code 02, before 31 August, 2016.

Please return suspect stock of part number 68143886AA. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 68174065AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 68141880AH, 68141881AH, 68145625AI, 68145626AI, 68189480AF and replacement part numbers are 68141880AI, 68141881AI, 68145625AJ, 68145626AJ & 68189480AG respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 05278632AF and replacement part number is 52030379AA which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part numbers: 1YG06JSCAC, 1YG06KEPAC, 1YG 06KFSAC, 1YG 06KGZAC, 1YG 06KBUAC and replacement part numbers are 1YG 1YG06KFSAD, 1YG 06KG ZAD, 1YG 06KBUAE respectively,which arein stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return all stock of following part number: 68188889AE and replacement part number is 68188889AF which isin stockand available. Please return suspect parts back to your facing depot using Return Code 02, before 05 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return suspect stock of following part numbers: 68036213AA, 68036230AF, 68158196AC, 68158197AD, & 68158454AD. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allstock of following part numbers:68241568AB,68241568AC,68241569AB,68241569AC, 68241570AB,68241571A.Replacement part numbersare 68241568AD,68241569AD,68241570AD,68241571AD, which are in stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

The customer may notice that the theft alarm feature is inoperative.

Customers may indicate that they feel a vibration coming from the rear of the vehicle at speeds between 80 kph (50 mph) and 120 kph (75 mph).

This same month last year we had over 40,000 open aged > 5 days tickets. As a result of focused efforts to verify vehicles are repaired and close tickets the number is now at just under 7,000 tickets.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*LJ

MODEL 2014 RAM 1500, RAM, WRANGLER. *PE

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

A customer may experience one or more of the following conditions. Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio remains on. HVAC temperature out of sync with radio display (KL vehicles). Track names may be displayed twice in USB or SD media modes. SD, USB or BTSA modes may become non-functional for a given ignition cycle. Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played. Navigation function may reset itself after using One-Shot VR. Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear. Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Park Sense tone continuously on. Radio display may show. Please insert USB Stick? Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to reverse. iPod would not resume playing after a VR session or phone call. Radio reset, screen lockup, blank screen or sluggish system.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

To verify proper functionality, turn on the ignition with no cables or devices plugged into the port. Connect a charging cable to the port, then connect the device. If the device receives power, the port is functioning to design. There are some minor compatibility issues with some charging cables including Apple Lightning cables. For questions regarding the charging port functionality, please call Dave Diovardi at Cell (248) 941-8704 or Rick Gordon at Cell (248) 630-6281.~

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Customers may describe the instrument cluster is illuminating by itself after the ignition has been off for an extended period of time (10 minutes or more).

Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

electrical harness connector is properly connected.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

**Improvements: Ability to communicate with Siri via UConnect. Ability to press Voice Recognition (VR) button for more than one second.** A customer may experience one or more of the following conditions: **Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles).** Track names may be displayed twice in USB or SD media modes. SD, USB or BTSA modes may become non-functional for a given ignition cycle. Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played. Navigation function may resets itself after using One-Shot VR. Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers (U.S. market only). Able to adjust audio balance / fade settings during a VR session. Correct condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on. Radio display may shows ?Please insert USB Stick?. Enhancement made when video is display in radio when using PAL format video disks. Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to rev

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory..

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

A customer may experience, one or more of the following conditions. Navigation function may resets itself after using One-Shot Voice Recognition (VR). Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers. (U.S. market only) Able to adjust audio balance / fade settings during a VR session. Correct, condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on. Enhancement to navigation routing. Radio display may shows ?Please insert USB Stick?. Enhancement made when video is display in radio when using PAL format video disks. Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to reverse. Enhancements for iPod or iPhone devices that may not start playing after connecting. iPod would not resume playing after a VR session or phone call. Radio reset, screen lockup, blank screen or sluggish system response time. Compass indicator turns off. Touch screen shut down message. Radio surround sound will not stay ON. Driver memory feature causes Sirius XM failure. Loss of radio presets. Battery drain - due to radio remains on. Uconnect apps don't load. AM/FM popping noises and/or static. Backup camera display is blank

? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when

? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho

? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho

replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

Please use relay replacement KIT part number: 68510768A$.

content not needed on light duty truck. Content removed was only used on heavy duty truck and not needed for light duty vehicles. Content that may not be present includes the following fuses: F15 (J Case A1-S) F16 (M Case) F32 (M Case) F33 (M Case) F34 (M Case) F39 (M Case) If the PDC is being replaced due to a failed internal fuel pump relay, the relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Diagnostic Trouble Codes (DTCs) P2463 ? Diesel Particulate Filter Soot Accumulation, and P2453 ? Diesel Particulate Filter Differential Pressure Sensor Circuit Performance Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

the Instrument Panel Cluster (IPC) with updated software. ? Customer may report that the odometer line disappears sometimes and comes back with an ignition cycle or changing cluster screens. ? The customer may notice when trying to switch the language from English to Spanish/French, only the radio will display the correct language. The cluster will still display English.

A customer may experience, one or more of the following conditions: ? Radio may reset, turn itself off and then back on again. All Symptom Listed Below Are For 2013 Vehicles Only: ? Radio may be muted. Any of DTCs B1400-92-Front Left Audio Speaker Output - Performance Incorrect Operation and/or B1404-92- Front Right Audio Speaker Output - Performance Incorrect Operation and/or B1408-92-Rear Left Audio Speaker Output - Performance Incorrect Operation and/or B140C-92-Rear Right Audio Speaker Output - Performance Incorrect Operation, maybe active or stored. ? Radio display screen may turn off. ? Radio will stay on after the vehicle is turned off with remote. (Applies to vehicle with Mopar remote start add on package only). ? Radio will stay on for 20 minutes after ignition is turned off and the only way to turn off the radio is by pressing the power button on the radio. Software was updated to have the radio shut off based on the cluster accessory delay setting.

The customer may describe LED Turn Signals do not properly display.

(VSIM) with the latest available software. Customers may notice uplift components connected to the VSIM inoperative at times. This is caused by a condition where as the VSIM locks up and becomes unresponsive. No DTCs will be reported for loss of communication between the VSIM and Central Body Controller (CBC). This can be corrected by updating the VSIM with the latest available software. SYMPTOM ONLY FOR 2013 DD AND DP with Power Take Off Prep (Sales Code LBN) Customers may experience after 30 minutes of operation the PTO may shut off. The PTO will start working again after the ignition is cycled.

? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Track names may be displayed twice in USB or SD media modes. ? Voice Recognition command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK) Vehicle only. ? DAB (Digital Audio Broadcast) is inoperative. ? Wrong routing for addresses with a longitude between 0 and -1 degrees. ? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they sho

identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68260866AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: 68085880AD, 68085880AF, 68085881AE, 68085881AF, 68085881AG. Replacement part numbers are: 68085880AG, and 68085881AH. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

are receiving this email as you have been identified to have stock on hand or have stock in transit to your dealership. Reports of dealers receiving incorrect fuel pressure sensors packaged as 68210332AA. Correct and suspect parts can be identified visually by the color of the label on the sensors. Correct sensors have white color label on the part whereas the suspect sensors have yellow colored labels. Reference pictures attached for visual identification. Please inspect stock on hand and return any suspect parts found back to your facing PDC using MRA code 02. Replacement parts can be obtained by reordering the same part number. Direct all questions via email to vn83@chrysler.com

A customer may experience, one or more of the following conditions. ? Improved Radio security protection to reduce the potential risk of unauthorized and unlawful access to vehicle systems (U.S. Market Only). ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connec

The radio should not be replaced for this issue if the fault is stored, if the code cannot be reproduced and no trouble can be found (radio functions properly). In this case it is no impact to the customer in any way. Do NOT replace the radio for this issue. Please contact John Carlesimo at cell (248) 941-8756 if you have any further questions regarding this fault.

contact Michael Wang at cell (248) 701-5351. If no response or contact is made within 15 minutes, proceed with repairs as necessary.

Please identify battery with the last 8 VIN digits along with the 15 digit Medtronic code from the GR-8 tester. If no response in 15 minutes, continue with the repair. Battery needs to be held and not turned in for core charges.

A customer may experience, one or more of the following conditions. ? Track names may be displayed twice in USB or SD media modes. ? SD, USB or BTSA modes may become non-functional for a given ignition cycle. ? Duplicate song titles may be displayed in USB mode. ? Last track is displayed but next track is being played. ? Navigation function may resets itself after using One-Shot Voice Recognition (VR). ? Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. ? GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. ? A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. ? Back-up camera image may be unclear or jittery/stutters at times. ? Enables Via Mobile software features when released to consumers. (U.S. market only) ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connecting. ? iPod would not resume playing after a VR session or phone call. ? Radio reset, screen lockup, blank screen or sluggish system respo

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory.

A customer may experience, one or more of the following conditions. Navigation function may resets itself after using One-Shot Voice Recognition (VR). Intermittently the Global Positioning System (GPS) may lose it?s location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers. (U.S. market only) Able to adjust audio balance / fade settings during a VR session. Correct, condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on Enhancement to navigation routing Radio display may shows ?Please insert USB Stick? Enhancement made when video is display in radio when using PAL format video disks Corrected the temperature slider bar not updating on Manual Temperature Control vehicles Navigation may not start or may lose position Rear camera may show a black screen for 3 seconds upon going to reverse Enhancements for iPod or iPhone devices that may not start playing after connecting iPod would not resume playing after a VR session or phone call Radio reset, screen lockup, blank screen or sluggish system response time Compass indicator turns off Touch screen shut down message Radio surround sound will not stay ON Driver memory feature causes Sirius XM failure Loss of radio presets Battery drain-due to radio remains on Uconnect apps don't load AM/FM popping noises and/or static Backup camera display is blank Compass direction may be inco

? Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. ? DAB preset list on the top of the screen doesn't change while scrolling with steering controls. ? Rear view camera jitter. ? Tuner reception software enhancements. ? HVAC temperature control enhancements. ? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:

have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016.

Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017.

Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory..

DAB (Digital Audio Broadcast) is inoperative. Wrong routing for addresses with a longitude between 0 and -1 degrees. Speed Camera UK & Spain complaining that the speed camera feature was not available with the latest MY14 software. DAB preset list on the top of the screen doesn't change while scrolling with steering controls. Rear view camera jitter. Tuner reception software enhancements. HVAC temperature control enhancements. SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). Battery drain due to the radio and cluster back-lighting staying on. Postal Code smart speller logic enhancements (EMEA markets only). AM/FM steering wheel mode switch button not working (LATAM markets only). Navigation Lockout Disable while vehicle is in motion (EMEA markets only). Removed network status indicators for SRT/APPS. Voice Recognition (VR) says 'cancel' when starting (App) applications. iPod would not resume playing after a VR session or phone call. Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. rear camera may show a black screen for 3 seconds upon going to reverse. Navigation would not start or would lose position. Removal of parental control under Apps menu. Turn by Turn navigation in the cluster set to ON by default. Transfer button does not pick-up and transfer incoming call. Some Russian letters are caps when they should be lower-case. Touch screen locks up in navigation, when Russian is selected. Address search availably when the vehicle is moving (EMEA markets only). VR messages in Spanish talks to fast. Recognition enhancement for Russian VR. Hands free audio too low for non-amp vehicle (KL). Intermittently Registration expired pop-up appears on display screen. Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). Incorrect time to destination

electrical harness connector is properly connected.

A customer may notice at low speed operation (below 7mph/11kph) a cluster display indicating an object is detected by the front park assist system. This will be indicated by the fourth (farthest) arc on the vehicle graphic on the cluster. This will typically occur on gravel or sloped surfaces, like an approach ramp. The system calibration is overly sensitive which is causing ground detection as an object in the far zone. Also a condition may happen where the park assist chime will sound continuously. On further inspection one or more of the following DTCs may be found: B128E-25-PTS SENSOR 1 - Signal Shape / Waveform Failure. B128F-25-PTS SENSOR 2 - Signal Shape / Waveform Failure. B1290-25-PTS SENSOR 3 - Signal Shape / Waveform Failure. B1291-25-PTS SENSOR 4 - Signal Shape / Waveform Failure. B1292-25-PTS SENSOR 5 - Signal Shape / Waveform Failure. B1293-25-PTS SENSOR 6 - Signal Shape / Waveform Failure. B1295-25-PTS SENSOR 8 - Signal Shape / Waveform Failure. B1296-25-PTS SENSOR 9 - Signal Shape / Waveform Failure. B1297-25-PTS SENSOR 10 - Signal Shape / Waveform Failure. B1298-25-PTS SENSOR 11 - Signal Shape / Waveform Failure.

The customer may experience a slow crank during very cold temperatures. On further inspection it may be found that the vehicle has the incorrect battery.

Improvements: Ability to communicate with Siri via UConnect. Ability to press Voice Recognition (VR) button for more than one second.** A customer may experience one or more of the following conditions: Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles). Track names may be displayed twice in USB or SD media modes. SD, USB or BTSA modes may become non-functional for a given ignition cycle. Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played. Navigation function may resets itself after using One-Shot VR. Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. A false Pop-up message may appear Vehicle Phone Requires Service even though the vehicle?s phone works properly. Back-up camera image may be unclear or jittery/stutters at times. Enables Via Mobile software features when released to consumers (U.S. market only). Able to adjust audio balance / fade settings during a VR session. Correct condition where user could not exit screen off mode. Mute button status was not being displayed correctly. Presets where not shown correctly or were deleted. Enhancements to POI. ParkSense tone continuously on. Enhancement to navigation routing. Radio display may shows ?Please insert USB Stick?. Enhancement made when video is display in radio when using PAL format video disks. Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. Navigation may not start or may lose position. Rear camera may show a black screen for 3 seconds upon going to rev

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

A customer may experience, one or more of the following conditions. ? Navigation display enhancement. ? Enables Via Mobile software features when released to consumers. ? Able to adjust audio balance / fade settings during a VR session. ? Correct, condition where user could not exit screen off mode. ? Mute button status was not being displayed correctly. ? Presets where not shown correctly or were deleted. ? Enhancements to POI. ? ParkSense tone continuously on. ? Enhancement to navigation routing. ? Radio display may shows ?Please insert USB Stick?. ? Enhancement made when video is display in radio when using PAL format video disks. ? Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. ? Navigation may not start or may lose position. ? Rear camera may show a black screen for 3 seconds upon going to reverse. ? Enhancements for iPod or iPhone devices that may not start playing after connecting. ? iPod would not resume playing after a VR session or phone call. ? Radio reset, screen lockup, blank screen or sluggish system response time. ? Compass indicator turns off. ? Touch screen shut down message. ? Radio surround sound will not stay ON. ? Driver memory feature causes Sirius XM failure. ? Loss of radio presets. ? Battery drain - due to radio remains on. ? Uconnect apps don't load. ? AM/FM popping noises and/or static. ? Backup camera display is blank. ? Compass direction may be incorrect. ? Vehicle's Icon changes on the navigation map. ? Loss of vehicle position on NAV map. ? ?Vehicle Phone Requires Service? message appears on 8.4? screen. ? Nav turn-by-turn enhancements. ? Nav map guidance enhancements. ? Nav text overlaps in detour menu. ? Nav map, vehicle location enhancements in areas with low GPS signals. ? Navigation shows vehicle in San

harnesses in the glove box for later installation. Tailgate keyless entry with back-up camera wiring kit missing from glove box.

HVAC control module with new software. Customers may experience a situation where the touch screen climate controls may ignore the first press of the front defrost button if it is the first climate button pressed after ignition ON. The second press of the front defrost button works correctly. If another climate button is pressed prior to the front defrost button, then the control will respond as desired.

The customer may notice that the temperature display will be cooler than the actual outside temperature, up to 20F degree lower. This condition is more noticeable the colder the temperature gets.

? SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only). ? Battery drain due to the radio and cluster back-lighting staying on. ? Postal Code smart speller logic enhancements (EMEA markets only). ? AM/FM steering wheel mode switch button not working (LATAM markets only). ? Navigation Lockout Disable while vehicle is in motion (EMEA markets only). ? Removed network status indicators for SRT/APPS. ? iPod would not resume playing after a VR session or phone call. ? Removed the cell signal indicators in the SRT and Apps button on non-US vehicles. ? rear camera may show a black screen for 3 seconds upon going to reverse. ? Navigation would not start or would lose position. ? Removal of parental control under Apps menu. ? Turn by Turn navigation in the cluster set to ON by default. ? Transfer button does not pick-up and transfer incoming call. ? Voice Recognition (VR) says 'cancel' when starting (App) applications. ? Some Russian letters are caps when they should be lower-case. ? Touch screen locks up in navigation, when Russian is selected. ? Address search availably when the vehicle is moving (EMEA markets only). ? VR messages in Spanish talks to fast. ? Recognition enhancement for Russian VR. ? Hands free audio too low for non-amp vehicle (KL). ? Intermittently ?Registration expired? pop-up appears on display screen. ? Arabic language for navigation only, not the keyboard (RJ3 RJ4 radio only). ? Incorrect time to destination, when ignition is cycled. ? Volume adjustment for navigation prompts, for phone call. ? Incorrect rear to center fade displayed at start up. ? Translation enhancements for French German and Spanish. ? Right arrow doesn't work for advancing through preset. ? Map zoom level reduced. ? Park sense audio tone stuck on. ?

A customer may experience not being able to turn off the ?Comfort Auto On? feature in the customer settings.

required.?Navigation Failed? message is displayed (2014 MY WK and KL with RG4). Clock does not automatically update to local time (2014 MY WK and KL with RG4). Poor or no connection to cellular network (2014 MY WK and KL with RG4). HVAC temperature out of sync with radio display (2014 MY KL with RG4). Some Uconnect App remote commands do not execute with the vehicle (2014 MY WK and KL with RG4). Display goes blank/black (2014 MY WK and KL with RG4).Cyrillic keyboard is missing in phone book (2014 MY WK and KL with RG4).Incorrect speed limit on NAV speed camera indication (2014 MY WK and KL with RG4). Poor reception for AM/FM radio.Duplicate song titles may be displayed in USB mode. Last track is displayed but next track is being played.SD, USB or BTSA modes may become non-functional for a given ignition cycle.Track names may be displayed twice in USB or SD media modes.Voice Recognition (VR) command ?Set Temperature? may not respond in Fahrenheit. United Kingdom (UK)Vehicle only.DAB is inoperative.Wrong routing for addresses with a longitude between 0 and -1 degrees. Speed camera UK&Spain complaining that the speed camera feature was not available with the latest MY14 software.SRT soft button missing for radios when vehicle is equipped with SRT feature (EMEA /LATAM markets only).Battery drain due to the radio and cluster back-lighting staying on. Postal Code smart speller logic enhancements (EMEA markets only).AM/FM steering wheel mode switch button not working (LATAM markets only).Navigation Lockout Disable while vehicle is in motion (EMEA markets only).Removed network status indicators for SRT/APPS.VR says 'cancel' when starting (App) applications.iPod would not resume playing after a VR session or phone call.Removed the cell signal indicators in the SRT and Apps button on non-US vehicles.Rear camera may show a black screen for 3 secon

MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. THE FOLLOWING POWERTRAIN SYSTEM IMPROVEMENTS/ENHANCEMENTS ARE INCLUDED IN THIS SOFTWARE RELEASE. THESE ENHANCEMENTS ARE LISTED BY VEHICLE APPLICATION.

THIS BULLETIN ALSO INVOLVES REPROGRAMMING POWER CONTROL MODULE *CN

FUSE F08, OXIDES OF NITROGEN (NOX) SENSOR HAS LABEL WITH INCORRECT FUSE SIZE, AND ORIGINAL LABEL SPECIFIES CORRECT SIZE AS 20 AMPS, NOT 30 OR 40 AMP. MODEL 2014 RAM 2500, 3500, 4500, 5500. *PE

*LJ

A SLOW OR NO PASSIVE ENTRY RESPONSE, OR RESPONSE TO REMOTE KEYLESS ENTRY (RKF), IS DUE TO RADIO FREQUENCY HUB MODULE SOFTWARE PROGRAMMING AND NEEDS NEW SOFTWARE PROGRAM. *PE

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Mirror Contacts Door Window Glass In The Folded Position.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

information prior to repairing the vehicle. Please contact Jim Smith via Cell Phone (248) 765-8972 If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair.

Loud metallic rattle noise coming from the roof headliner area while driving over rough road surfaces and/or upon door closing.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

mirror tilt in reverse operation. The customer may describe one mirror tilting in reverse and the other mirror not tilting and/or the customer may describe not being able to turn the tilt in reverse feature on/off.

Front center seat armrest storage compartment lid is difficult to latch due to hard lid bumpers.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 05182600AC. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock,or have stock in transit to your dealership. Please return all suspect stock of following part numbers:68159725AB,& 68261143AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02,before 27 O ctober,2015. Return any open orders in process too. Direct all questions via email to MO PARQ C@fcagroup.com

LT:04805839AD

To do this, add the LEG (Trailer Tow Mirrors) sales code to the VIN using DealerCONNECT and then performing a vehicle re-configuration using the WiTech tool.~ After Kit is completely installed, perform the following;~ 1. Add LEG sales code to the VIN under the ?Vehicle Option Updates? Found on Dealerconnect~ 2. Update Vehicle Configuration by using the WiTech tool and performing ?Restore Vehicle Configuration.?

you receive kit PN 68315574AA, discard the instruction sheet shipped with the kit and reference TSB 23-001-16 REV. B for correct bumper installation instructions. ~ Note: This only applies to the AA level of the kit

Front center seat armrest storage compartment lid is difficult to latch due to hard lid bumpers.

Ensure it visually matches the Turn Signal on the opposite mirror. If not, both sides will need to be replaced.

stock in transit to your dealership. Please return suspect stock of part number 68160775AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 26 August, 2016.

A)

Please return allsuspect stock of part numbers:68212041AC,68141170AC,55112738AA.See attachmentsfor identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

Please return all suspect stock of following part numbers: 57010364AI, 57010365AI, 57010504AJ, 57010505AJ, 68224368AB, 68224369AB. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017.

numbers:55395241AG,55395241AE.Replacement ispart number 55395241AH which isin stock and available. Please return suspect partsback toyour facing depot using Return Code 02,before 12April,2017

have stock in transit to your dealership. Please return suspect stock of part number 04589131AG, 04589243AG . See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 7 April, 2016.

mirror tilt in reverse operation. The customer may describe one mirror tilting in reverse and the other mirror not tilting and/or the customer may describe not being able to turn the tilt in reverse feature on/off.

Ensure it visually matches the Puddle Light on the opposite mirror. If not, both sides will need to be replaced

If Turn Signal/Puddle Lamp is visually different from OE, you will need to swap the original lamp to the new mirror unit.

Loud metallic rattle noise coming from the roof headliner area while driving over rough road surfaces and/or upon door closing.

information prior to repairing the vehicle. Please contact Jim Smith via Cell Phone (248) 765-8972 If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair.

by cycling the upper console lid. Check for a green dot sticker on the back of the console behind the rear panel by the hinge. ~ If the above complaint is verified and the console DOES NOT have a green dot sticker near the hinge (behind the back panel), order kit PN 68315574AA and install per the included instructions. Otherwise continue with the repair. Please reference TSB 23-001-16 Rev. E (or later version).

vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience one or more of the following: Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling. "

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

to be performed according to this recall. Service Bulletin 18-064-15 is no longer applicable for vehicles involved in this recall. Those vehicles that have already had this repair performed, as determined by our warranty records, have been excluded from this recall. The Selective Catalytic Reduction (SCR) catalyst on about 11,400 of the above vehicles is experiencing washcoat degradation, which may lead to the exceedance of exhaust emission standards.

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

an EVAP dual vapor canister filter kit(Mopar part #68478013AA)is available in place of the OEM single vapor canister filter.This kit should not be installed on vehicles driven in normal conditions that are not subjected to the below symptom/conditions. Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience the following conditions:Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling.

degradation, which may lead to the exceedance of exhaust emission standards.

injector line to check for a leak during New Vehicle Preparation. The DEF system may not become functional until the vehicle has been driven for 20 miles at one time. This Bulletin will give the steps necessary to ensure DEF system is not leaking. A very small number of vehicles may experience a DEF fluid leak under the vehicle. Upon further investigation the Technician may find that the DEF injector is broke.

injector line to check for a leak during New Vehicle Preparation. The DEF system may not become functional until the vehicle has been driven for 20 miles at one time. This Bulletin will give the steps necessary to ensure DEF system is not leaking. A very small number of vehicles may experience a DEF fluid leak under the vehicle. Upon further investigation the Technician may find that the DEF injector is broke.

degradation, which may lead to the exceedance of exhaust emission standards.

an EVAP dual vapor canister filter kit(Mopar part #68478013AA)is available in place of the OEM single vapor canister filter.This kit should not be installed on vehicles driven in normal conditions that are not subjected to the below symptom/conditions. Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience the following conditions:Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling.

OD55507)

either having stock, or have stock in transit to your dealership. Please return all suspect stock of following part number: 68146401AA. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 09 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

either having stock, or have stock in transit to your dealership. Please return following part numbers: CBTTP57FAA, & CBTTP57FAB. Replacement part number CBTTP57FAC will be available week beginning 26 O ct., 2015. There are reports of pre-programmed FO BS in these kits, preventing dealer pairing of W IN and Transmitter Key FO BS. If repair is needed prior to new part availability, order two of part number 05026886AK transmitter Integrated Key FO B. Please return suspect parts back to your facing depot using Return Code 02, before 06 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies to 2014-2015 WD, WK or KL Vehicles. A customer may experience a popping noise when listening to AM stations.

(248) 622 8109 ~ Mexican Dealers please call Ricardo Lozada at cell +52 1 55 1370 3187. If no return call in 15 minutes, continue with repair.

please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair.

A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.

A customer may experience one or more of the following conditions: Radio display screen will lock up and reset intermittently. Incorrect routing directions to fuel stations when using Travel Link. Unable to turn on heated seats; icon is greyed out. Navigation screen goes blank. Navigation system freezes/locks up. Vehicles with Mopar special edition radio will update radio?s splash screen. Navigation icon shows the vehicle going backward when it?s moving forward.

stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

Please return allsuspect stock of part numbers:68148794AH,68148794AF,68148794AD,68156453AH,68156453AF, 68156453AD,68161542AE,68161542AD.See attachment for identifying suspect material. Please return suspect partsback toyour facing depot using Return Code 02,before 19April,2017.

injector line to check for a leak during New Vehicle Preparation. The DEF system may not become functional until the vehicle has been driven for 20 miles at one time. This Bulletin will give the steps necessary to ensure DEF system is not leaking. A very small number of vehicles may experience a DEF fluid leak under the vehicle. Upon further investigation the Technician may find that the DEF injector is broke.

to be performed according to this recall. Service Bulletin 18-064-15 is no longer applicable for vehicles involved in this recall. Those vehicles that have already had this repair performed, as determined by our warranty records, have been excluded from this recall. The Selective Catalytic Reduction (SCR) catalyst on about 11,400 of the above vehicles is experiencing washcoat degradation, which may lead to the exceedance of exhaust emission standards.

may lead to the exceedance of exhaust emission standards.

2014 model year (DS) RAM Truck (1500 series). The transmission case may have an improperly machined park rod guide plate mounting surface. This could cause a loss of park rod guide plate fastener clamp load and eventually the park rod guide plate fasteners may loosen. A loose park rod guide plate and fasteners may not allow the park pawl to fully engage. This condition could cause unintended vehicle movement and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the transmission case. Transmissions found with an improperly machined park rod guide plate mounting surface must be replaced. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

The customer may experience not being able to shift out of park. This condition can be corrected by turning off the vehicle and allowing all of the modules to go to sleep. Once the modules have gone through a key cycle the DTC will go from active to stored and then the vehicle can be shifted out of park. On further inspection DTCs P0607-00-ECU INTERNAL PERFORMANCE and P0928-00-BTSI CONTROL may be found active or stored.

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

The customer may indicate that they may have experienced any of the following: ? 4x4 Low Mode shift quality during a medium to heavy throttle ? MIL Illumination for DTC P215C - OUTPUT SHAFT SPEED WHEEL SPEED CORRELATION In addition, calibration changes have been made in the following areas to improve: ? Powertrain braking while in Tow/Haul mode ? Downshift response from a medium to heavy pedal ? Drivability at high altitude ? Acceleration performance during cruise control operation This calibration release also corrects a condition where DTC U11C3 may have been displayed when DTC U11E3 should have been displayed resulting in a possible misdiagnosis.

Transmission Control Module (TCM) with new software. Customers may indicate that the vehicle does not downshift quick enough under medium to heavy throttle.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: ? Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy. ? Improved transmission Quick Learn routine performance (Applies only to DJ vehicles)

2014 model year (DS) RAM Truck (1500 series). The transmission case may have an improperly machined park rod guide plate mounting surface. This could cause a loss of park rod guide plate fastener clamp load and eventually the park rod guide plate fasteners may loosen. A loose park rod guide plate and fasteners may not allow the park pawl to fully engage. This condition could cause unintended vehicle movement and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the transmission case. Transmissions found with an improperly machined park rod guide plate mounting surface must be replaced. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

The customer may indicate that they may have experienced any of the following: ? 4x4 Low Mode shift quality during a medium to heavy throttle ? MIL Illumination for DTC P215C - OUTPUT SHAFT SPEED WHEEL SPEED CORRELATION In addition, calibration changes have been made in the following areas to improve: ? Powertrain braking while in Tow/Haul mode ? Downshift response from a medium to heavy pedal ? Drivability at high altitude ? Acceleration performance during cruise control operation This calibration release also corrects a condition where DTC U11C3 may have been displayed when DTC U11E3 should have been displayed resulting in a possible misdiagnosis.

Transmission Control Module (TCM) with new software. Customers may indicate that the vehicle does not downshift quick enough under medium to heavy throttle.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: ? Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy. ? Improved transmission Quick Learn routine performance (Applies only to DJ vehicles)

2014 model year (DS) RAM Truck (1500 series). The transmission case may have an improperly machined park rod guide plate mounting surface. This could cause a loss of park rod guide plate fastener clamp load and eventually the park rod guide plate fasteners may loosen. A loose park rod guide plate and fasteners may not allow the park pawl to fully engage. This condition could cause unintended vehicle movement and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the transmission case. Transmissions found with an improperly machined park rod guide plate mounting surface must be replaced. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

the following scenario occurs; The T79 or U11 recall was completed where the shifter inspection was acceptable and the software flash was performed but then the customer comes back needing the BTSI bracket replaced for coming out of park without the brake or key.

If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any DTCs identified with the scan tool and document them on the repair order.

check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer's concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

The customer may experience not being able to shift out of park. This condition can be corrected by turning off the vehicle and allowing all of the modules to go to sleep. Once the modules have gone through a key cycle the DTC will go from active to stored and then the vehicle can be shifted out of park. On further inspection DTCs P0607-00-ECU INTERNAL PERFORMANCE and P0928-00-BTSI CONTROL may be found active or stored.

The customer may indicate that they may have experienced any of the following: ? 4x4 Low Mode shift quality during a medium to heavy throttle ? MIL Illumination for DTC P215C - OUTPUT SHAFT SPEED WHEEL SPEED CORRELATION In addition, calibration changes have been made in the following areas to improve: ? Powertrain braking while in Tow/Haul mode ? Downshift response from a medium to heavy pedal ? Drivability at high altitude ? Acceleration performance during cruise control operation This calibration release also corrects a condition where DTC U11C3 may have been displayed when DTC U11E3 should have been displayed resulting in a possible misdiagnosis.

Transmission Control Module (TCM) with new software. Customers may indicate that the vehicle does not downshift quick enough under medium to heavy throttle.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: ? Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy. ? Improved transmission Quick Learn routine performance (Applies only to DJ vehicles)

2014 model year (DS) RAM Truck (1500 series). The transmission case may have an improperly machined park rod guide plate mounting surface. This could cause a loss of park rod guide plate fastener clamp load and eventually the park rod guide plate fasteners may loosen. A loose park rod guide plate and fasteners may not allow the park pawl to fully engage. This condition could cause unintended vehicle movement and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the transmission case. Transmissions found with an improperly machined park rod guide plate mounting surface must be replaced. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?

to be tucked behind the flange of the bumper bracket. No fasteners are used to attach the liner and the bumper when vehicle is equipped with a steel front bumper.

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

The customer communication requested return of unsold inventory due to an internal software issue. The internal software issue leads to a fault code for lack of communication with the Trailer Brake Controller. This will cause the part to be replaced because because module installation cannot be completed due to this lack of electronic communication.

The customer communication requested return of unsold inventory due to an internal software issue. The internal software issue leads to a fault code for lack of communication with the Trailer Brake Controller. This will cause the part to be replaced because because module installation cannot be completed due to this lack of electronic communication.

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

Start Date: 10/27/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of part numbers: 68144663AA, 52013874AE. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to MOPARQC@fcagroup.com

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Jim Allie via Cell Phone (248) 736-5349 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Jim would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Jim does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to james.allie@fcagroup.com

surfaces and replacing the front brake pads.

Move the mirror to its full foward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.

Anit-Lock Brake System (ABS) module software. No DTC will be found.

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Mihaela Colfescu via cell (248) 841-5736 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Mihaela would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Mihaela does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to mihaela.colfescu@fcagroup.com~

It will appear raised either left or right of center. Please photograph the condition, measure the gap between the bumper and step pad. Then contact Mihaela Colfescu via cell (248) 841-5736 with this information. We may want to have the whole bumper assembly returned for study. ~ If the dealership is within the Metro Detroit Area, Mihaela would like to analyze the vehicle in person prior to repair. ~ If the dealership is not close, please take pictures and a detailed description of what is causing the issue including where on the Step Pad the issue is occurring. If Mihaela does not return the call within 15 minutes please gather the requested information and proceed with the repair. Information can be emailed to mihaela.colfescu@fcagroup.com

18.01.35 (BU Vehicles)

A customer may experience the radio display screen is locked on the Ram logo. This software update is to prevent this condition from occurring. Vehicles equipped with satellite radio (sales code RSD) may have a condition were the radio may reset a few times during a drive cycle. This condition is very intermittent.

A customer may experience the radio display screen is locked on the Ram logo. This software update is to prevent this condition from occurring. Vehicles equipped with satellite radio (sales code RSD) may have a condition were the radio may reset a few times during a drive cycle. This condition is very intermittent.

No FM or AM reception.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

The customer may notice when trying to switch the language from English to Spanish/French, only the radio will display the correct language. The cluster will still display English.

No FM or AM reception.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

A customer may experience the radio display screen is locked on the Ram logo. This software update is to prevent this condition from occurring. Vehicles equipped with satellite radio (sales code RSD) may have a condition were the radio may reset a few times during a drive cycle. This condition is very intermittent.

The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus. On further inspection U0186-00 Lost communication with the audio amplifier may be found.

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

SYMPTOM/CONDITION: **Improvements: Ability to communicate with Siri via UConnect. Ability to press Voice Recognition (VR) button for more than one second.**

MODEL 2013-14. *PE

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

to replace the foil patch for recall R47.

This is due to wax or other chemical substance being used on a grain in molded color part. You can clean the applique using isopropyl alcohol. This is not a warrantable condition.

cutting them off prior to installation. This backet is on the front crossmember.

A test-drive snap shot may help you isolate the source of the issue.

to replace the foil patch for recall R47.

If you don't receive a response within 20 minutes, then continue with normal repair procedure.~ Please follow this procedure to resolve Center Floor Console noise (e.g. ticking, buzz, squeak, rattle):~ 1) Remove tape/film from the Center Floor Console latching surfaces within the Armrest Lid {upper compartment} & bezel and Storage Bin {lower compartment} latch & bezel surfaces).~ 2) Apply interior cleaner onto cloth to remove the tape/film adhesive from the plastic latch & bezel and Storage Bin & Armrest Lid contact surfaces.~ Verify problem is resolved.

the Charge Air Cooler (CAC) system for excessive water and/or ice and drying the CAC components if needed. It also involves installing a winter front cover.

vehicles may develop internal icing in cold temperature regions. This condition may cause the Malfunction Indicator Light (MIL) to illuminate and cause the vehicle to experience a 35 mph limp in condition. A winter front cover must be installed when sustained day and night time temperatures drop below 30 F (-1 C).

the Charge Air Cooler (CAC) system for excessive water and/or ice and drying the CAC components if needed. It also involves installing a winter front cover.

industry awareness regarding the use of recycled or salvage parts.

vehicles may develop internal icing in cold temperature regions. This condition may cause the Malfunction Indicator Light (MIL) to illuminate and cause the vehicle to experience a 35 mph limp in condition. A winter front cover must be installed when sustained day and night time temperatures drop below 30 F (-1 C).

industry awareness regarding the use of recycled or salvage parts.

This condition may cause the Malfunction Indicator Light (MIL) to illuminate and cause the vehicle to experience a 35 mph limp in condition. A winter front cover must be installed when sustained day and night time temperatures drop below 30 F (-1 C).

The customer may experience when exiting a dark parking structure or dark tunnel the auto headlamps may not turn off. The customer may also experience when driving on an over cast day the auto headlamps may cycle on and off frequently.

Please return suspect stock of following part numbers: 68110016AC, 68110016AD, 68110016AE, 68110017AD, 68236104AC, 68236105AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31 August, 2016.

INFORMATION REGARDING AUTO HEADLAMP ENHANCEMENTS, CHECKING TUNNEL DETECTION VALUES AND PERFORMING A VEHICLE RECONFIGURATION IF NEEDED. *LJ

*LJ

If no response in 15 minutes, proceed with ordering the part

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

MODEL 2013-2014 RAM 1500. *PE

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet.

Please return stock of part number 68103256AG packaged before 2016/08/01. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016.

If no answer, and no return call in 15 minutes, proceed with repair.

THE RADIO FREQUENCY ON SOME HUB VEHICLES HAVE SOFTWARE PROBLEMS THAT CAUSE SLOW KEYLESS ENTRY RESPONSE. *LJ

technician an overview of the steps a customer will need to take to complete the update.

as either having stock, or have stock in transit to your dealership. Please return all suspect stock of follow ing part number: 68245351AB. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.

and 2015 Ram 1500 (DS/DX) vehicles built before 4/1/2014. These vehicles were built with a Front Lower Control Arm cross member that is not compatible with this skid plate. This cross member doesn't include the bolt attachment holes. Skid plates can be installed on vehicles built on or after 4/1/2014, if built with the a compatible Front Lower Control Arm cross member.

spare tire winch cable when storing under the vehicle. The adapter is part number 6824863AA and requires three (3) mounting nuts; PN 68150129AA.

B)