2013 Prevost X3 TSBs
167 Technical Service Bulletins across 16 categories
Categories
Electrical
43 bulletinsBOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good...
Read full bulletin
working order, perform the steps which follow to help you perform a more precise diagnosis.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - Mention added stating to disable Prime;...
Read full bulletin
Parts added in the kit.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM - Mention...
Read full bulletin
added stating to disable Prime; Parts added in the kit
Added: Power cables for L.H.
Read full bulletin
side alternator & fan drive breaker box
This instruction sheet explains how to install Delco Remy Alternators
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
On the vehicles affected by this bulletin, verify the revision numbers of the steering wheel gateway module and multiplex software.
Read full bulletin
If applicable, replace with the latest version. A power source improvement is also required. On some vehicles, as a temporary measure, a switch was installed on the left dashboard for cruise control SET and RESUME. This installation must be removed to restore these controls to the steering wheel.
On the vehicles affected by this bulletin, replace the LTD, relocate and replace the IR sensor as described in the...
Read full bulletin
following procedure.
On the vehicles affected by this bulletin, a new center mount battery box cover offering better overall sealing and...
Read full bulletin
simplified installation is available and may be installed at next service occasion.
A new software version (v1.06) is available to update the CANtrak (Tire Pressure Monitoring System) module.
Read full bulletin
This new version will allows a 10 min. delay before the ?SYSTEM ERROR NOT ALL TIRES MONITORED? message appears in the vehicle cluster when a tire pressure sensor loses its connection. NOTE: The new software version will only delays the cluster message, the CANtrak screen will still displays a ??? code for the corresponding pressure sensor.
This Maintenance Information explains that on some post EPA 2010 vehicles, it is possible for the combined charging and...
Read full bulletin
starting system F81 fuse to blow unexpectedly. To avoid this situation, a 3 amp diode can be added to the corresponding 24CO circuit to prevent electrical back-flow to the fuse. The following procedure describes the steps to follow to perform this modification.
When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is...
Read full bulletin
required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.
On the vehicles affected by this bulletin, the spot welded hex nut that holds the battery box cover retaining rod may break loose.
Read full bulletin
Follow the procedure described below to repair vehicles.
On the vehicles affected by this bulletin, relocate the video fuse in the SMI box closer to the door for better access.
On the vehicles affected by this bulletin, replace the destination sign power harness to resolve electrical interference...
Read full bulletin
between sign and public address (PA) system.
On the vehicles affected by this bulletin, a relay needs to be added to allow the DEF to return to the tank after turning the key to the OFF position.
Read full bulletin
In addition, the ACM & MCM need to be reprogrammed to the latest version.
On the vehicles affected by this bulletin, the NOx sensor must be replaced and the EMS software requires an update.
Read full bulletin
This must be done to allow correct emissions inspection in particular states including California.
On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical...
Read full bulletin
compartments is required.
On the vehicles affected by this bulletin, replace the Exhaust Gas Recirculation Venturi tube and sensor for an improved...
Read full bulletin
design.
This Instruction Sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay...
Read full bulletin
base p/n 564210
This instruction sheet explains how to install additional restraint for plastic shields over drive axle wheels.
Read full bulletin
Use kit #3200407 to secure the shields to the bus structure.
This Instruction Sheet explains how to assemble the BENDIX FLR10 AND FLR20 RADAR SENSOR ALIGNMENT TOOL
New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost...
Read full bulletin
vehicles equipped with Bosch HD10 alternators.
On the vehicles affected by this bulletin, remove selected wires from C15 and C58 of the HVAC system wiring, and place...
Read full bulletin
them in new connectors C15B and C58B. New connectors have a higher amp rating. We recommend inspecting connectors C15 & C58 for heat damage before ordering parts. Depending on connector condition, order additional parts along with main kit. See Additional Parts table.
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors.
Read full bulletin
Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part...
Read full bulletin
number #21212425.
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors.
Read full bulletin
Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
On the vehicles affected by this bulletin, on the HVAC system wiring, remove selected wires from C15 and C58 and place...
Read full bulletin
them in new connectors C15B and C58B. New connectors have a higher amp rating.
On the vehicles affected by this bulletin, add Z clips to secure the direct light lenses, 13 lenses per vehicle.
On the vehicles affected by this bulletin remove the ACM relay and base identified R49.
Read full bulletin
Reconnect the 24V power wire and protect the remaining signal wires with shrink tube.
On the vehicles affected by this bulletin, it is possible to observe signs of corrosion at the base of the master relay...
Read full bulletin
installed in the vehicle battery box. At the next service occasion, install a new relay along with shims between the relay mounting flange and the battery box bottom in a way that space is created between the relay base and the battery box bottom, preventing corrosion of the relay.
On the vehicles affected by this bulletin, perform a power source improvement and a multiplex software update for the steering Gateway module.
Read full bulletin
On a limited number of vehicles, the module will be replaced with the latest version of the part.
On the vehicles affected by this bulletin, software updates with enhancements are available for the multiplex system,...
Read full bulletin
for the EMS and aftertreatment control module (ACM). On all vehicles, perform a DPF Service Regeneration and Crystal Sublimation when programming is completed.
On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical...
Read full bulletin
compartments is required.
On the vehicles affected by this bulletin, replace the prototype version of the Urea Quality Sensor #21891229 by the...
Read full bulletin
production version of the sensor #22073036.
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternator.
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
PREVOST: THE COMBINED CHARGING AND STARTING SYSTEM F81 FUSE, ON SOME COACHES, CAN UNEXPECTEDLY BLOW AND NEED A 3 AMP...
Read full bulletin
DIODE TO CORRESPONDING 24CO CIRCUIT TO PREVENT ELECTRICAL BACK FLOW TO FUSE. MODELS 2011-2013 H3, H3-45 VIP CONVERTED, X3-45, X3-45 VIP CONVERTED, XL2-45 ENTERTAINER CONVERTED. *PE
Engine
33 bulletinsImproved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair From US10 to newer engine generation
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
This Instruction sheet explains how to install the Electric Cooling System with Bosch Alternators on X3 series vehicles...
Read full bulletin
equipped with US10 up to GHG17 engines
This Instruction sheet explains how to install the Electric Cooling System with Bosch Alternators on X3 series vehicles...
Read full bulletin
equipped with US10 up to GHG17 engines;
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13...
Read full bulletin
Engines
This Warranty Bulletin explains how to update the VECU (Vehicle Electronic Control Unit) parameters to allow auto engine...
Read full bulletin
brake function with the I-Shift transmission.
This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On...
Read full bulletin
Volvo D13 Engine
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13...
Read full bulletin
Engines
This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine
On the vehicles affected by this bulletin, perform the following verifications and modifications on the A/C system: ...
Read full bulletin
Bulletin is divided in five steps, refer to detailed instructions below. STEP 1: Unloader replacement (Step moved to Warranty Bulletin WB15-19) STEP 2: System vacuum, wiring update, remote pressure transducer and switch installation. STEP 3: Seal the evaporator compartment ventilation discharge duct. STEP 4: Check Evaporator expansion valve bulb position and MUX software version. STEP 5: Dynamic A/C system test to confirm all functions operate correctly.
On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.
Risk of premature failure of top fan support due to absence of weld.
Read full bulletin
In the engine compartment above radiator, inspect support to make sure support has two welds in the corners.
Inspect each gas cylinder to make sure there is no interference with the passenger's floor stiffeners when luggage door...
Read full bulletin
is closed.
ON the vehicles affected by this bulletin, update the Engine air intake pipe.
This Maintenance Information explains that hose clamps with a smaller diameter are available to increase the adjustment...
Read full bulletin
range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocharger.
When performing the next periodic maintenance, check clearance between the 4-inch OD turbooutlet pipe (Prevost part...
Read full bulletin
number 052953) and a close support bracket. If evidence of rubbing isfound, i.e. scratched paint on the 4-inch OD turbo outlet pipe, a modification of the support bracket can be performed in order to increase the clearance between the involved components. The support bracket will remain strong enough for the duty even after being modified.
On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is...
Read full bulletin
displaying incorrect information regarding the R34 relay voltage. Specifically, the R34 relay should be identified as a 24 volt relay instead of a 12 volt relay. Consequently, all affected vehicles must have a small decal displaying the correct information applied over the rear junction box decal R34 relay description.
This Maintenance Information explains how to perform an inspection of the vehicle power cables.
Read full bulletin
Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
This Maintenance Information presents an improved differential breather kit, identical to the one now used in production.
Read full bulletin
This new breather incorporates a "J" shaped hose that prevents oil leakage and water ingestion while allowing the axle to vent.
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors...
Read full bulletin
and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
On the vehicles affected by this bulletin, the engine oil pressure sensors for the piston cooling jet (PCJ) and the main...
Read full bulletin
oil gallery have to be replaced with an updated pressure sensor to avoid erroneous low oil pressure diagnostic codes.
On the vehicles affected by this bulletin, perform a turbo replacement if fault codes 27 FMI 7 or SPN641 FMI 7 or P004607 (OBD13) are found.
Read full bulletin
Bulletin affects D13H engines with serial number from 984581 up to 1026719, excluded.
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors...
Read full bulletin
and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors...
Read full bulletin
and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
This Maintenance Information shares information about the Bendix M-32QR valve replaced by M-40QR model htat need to be...
Read full bulletin
taken into consideration, specially when switching them for the first time on a vehicle.
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On...
Read full bulletin
Volvo D13 Engine
On the vehicles affected by this bulletin, perform a software update of ECM and ACM to modify the dosing strategy.
Read full bulletin
The software will also improve urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design and modify coolant hose routing to the dozer valve to provide additional cooling at engine shutdown.
On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM...
Read full bulletin
(Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.
On the vehicles affected by this bulletin, change the flexible hose at the engine air intake
Other
31 bulletinsAir Tanks Draining Sequence.
Read full bulletin
Revision: A - Erroneous Secondary & Accessory tanks location.
Air Tanks Draining Sequence
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
SIGMA PASSENGER SEATS PARTITION KIT
Repair instructions to address fault codes P207F-00; P20EE-00
Repair instructions to address fault codes P207F-00 - Reductant Quality
Repair instructions to address fault codes P008A-00; P0087-00
PREVOST VEHICLE DISINFECTION PROCEDURE
The intent of this procedure is to guide you through the steps required to program a MCM especially for the control of...
Read full bulletin
the electric fan drive as required for conversion kit of instruction sheets IS-19900, IS-19901, IS19910, IS-19912.
This instruction sheet explains how to install an ELD interface on OBD vehicles
On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
This instruction sheet explains how to install and adjust drag link # 660699
This instruction sheet explains how to install and adjust drag link # 660699
This instruction sheet explains how to install hatches with fan on X3 vehicles.
This instruction sheet explains how to replace the left bell crank using kit 161349
On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
This instruction sheet explains how to install and adjust drag link # 660699
On the vehicles affected by this bulletin, replace the drag link.
On the vehicles affected by this special bulletin, replace the rear tripod member.
Addition of a ring is required to prevent excessive squeezing of the o-ring and keep it in place.
On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
On the vehicles affected by this bulletin, improvement of a Charge Air Cooler tube support is required.
Read full bulletin
This is a ?Fix as Fail? bulletin, repair only the vehicles showing a cracked CAC tube.
On the vehicles affected by this bulletin, install a rock shield under Crank shaft to prevent belts from being thrown
This instruction sheet explains how to use the Bosch HD10 24V-150A Altenrator Conversion Kit
This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)
This instruction sheet explains how to install an ELD interface on OBD vehicles
This conversion kit explains how to to disable the ACB radar.
This Instruction Sheet explains how to replace 562489 Dimmer, using kit #069136
This conversion kit explains how to remove TGW1 from vehicles using Tech Tool, no manual VDA changes needed.
Read full bulletin
This conversion kit will work for any vehicle equipped with TGW1 up to the VIN's listed on the bulletin.
On the vehicles affected by this bulletin, torque must be verified on one of the axle support mounting bolts.
Read full bulletin
An interference of a production tool with the casting on the nut side of the fastener may have resulted in lower effective torque.
On the vehicles affected by this bulletin, the upper support of the tripod fan support must be inspected for the presence of weld.
Read full bulletin
If no weld is found, it must be replaced.
Fuel System
9 bulletinsThis instruction sheet explains how to install a flap over the diesel filling cap
On the vehicles affected by this bulletin, an improved 90 degree elbow is available.
Read full bulletin
Proceed to replacement at next service occasion.
On the vehicles affected by this bulletin, there is a risk of bi-metal contact (stainless steel & aluminum) leading to ...
Read full bulletin
corrosion where side reflector is installed on the evaporator door.
Grille frame gluing verification on the DPF door (left side, over the radiator door).
Read full bulletin
If part shows no sign of separation or ungluing, it is ok. If testing reveals poor bonding, remove grille, glue and double face tape.
Possibility of galvanic corrosion between the aluminium door and the stainless steel evaporator door retaining mechanism.
Read full bulletin
Procedure to solve the issue.
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
On the vehicles affected by this bulletin, inspect the fuel injectors serial numbers and replace if required.
This Instruction sheet explains how to modify the Support beam (Part # 30022 Installation)- as part of the X3 Fuel Tank...
Read full bulletin
installation
Possible air return between evaporator air conduit and compartment.
Read full bulletin
No airtightness between duct and floor / floor structure. Bulletin to describe how to add a sealing joint for better air tightness.
HVAC & Climate
8 bulletinsCENTRAL HVAC MERV FILTERS INSTALLATION
EBERSPACHER PREHEATER INSTALLATION In replacement of Spheros & Valeo preheaters
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds...
Read full bulletin
technicians to clean the oil filter/strainer and the magnetic drain plug.
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds...
Read full bulletin
technicians to clean the oil filter/strainer and the magnetic drain plug.
This bulletin explains how to add a reinforcement bracket to Bitzer A/C compressor to increase the installation...
Read full bulletin
stiffness and reduce vibration amplitude.
On the vehicles affected by this bulletin install an updated proximity switch on the vehicle compressor door following...
Read full bulletin
Instruction Sheet IS-12026.
On the vehicles affected by this bulletin, the pre-heater thermostat must be changed to ensure the proper functioning of...
Read full bulletin
the system.
Body & Paint
8 bulletinsThe light switch may operate incorrectly when doors are closed for vehicles affected by this bulletin.
Read full bulletin
Corrective action is presented.
Interference may occur between the WCL platform and the cassette access door when the platform is loaded at its...
Read full bulletin
extremity while lifting.
This Maintenance Information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid...
Read full bulletin
reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5/8po, 3/4po, 7/8po, 1 1/8po and 1 3/8po inside diameter (I.D) can be replaced by new WAVE SEAL type constant torque hose clamps.
The door may unlock and open in normal operating conditions.
Read full bulletin
The rod that operates the mechanism is too short.
On the vehicles affected by this bulletin, clean the breakers posts and bus bars, apply corrosion protection.
Read full bulletin
Check compartment cover seal condition.
Following introduction of new aluminium doors on x serie vehicles equipped with WCL, the decal showing how to manualy...
Read full bulletin
operate the wcl (on the wcl access door) needs to be resized. New decal 409435 must be installed on the series x wcl
On the vehicles affected by this bulletin, make sure that the vertical posts #22177 between baggage compartment are not...
Read full bulletin
contaminated by rush (traces, corrosion pin-holes).
On the vehicles affected by this bulletin, perform the proactive replacement of the lower hinges for both service doors.
Steering
6 bulletinsSTEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles.
Read full bulletin
The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE POWER STEERING PUMP DISCHARGE HOSE (PRESSURE) - #161335P OR #160039
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped...
Read full bulletin
with Dana S82, S84 / S84U I-beam axles, 1994- today
Pre-Delivery & Maintenance
6 bulletinsSTORAGE AND STARTUP GUIDELINES: Periodically, circumstances arise requiring operators to temporarily park a coach in storage.
Read full bulletin
Whether it is a few weeks or several months, sporadic out of service times or a full stop, Prevost recommends following the guidelines in this document during times when: The coach can be operated on a regular/weekly basis while in storage. The coach will be in storage for an extended period without any operation. The coach will return to service following an extended period of downtime.
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
This Service Center Instructions explains how to install the Prevost Ultimate Entertainment System
Radius rod support weld inspection: weld beads may be too small on radius rod supports on rear sub-frame.
This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough...
Read full bulletin
structural inspection.
Transmission
6 bulletinsVOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX.
Read full bulletin
HYDRAULIC END LIMITER ADJUSTMENT. All models equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
On the vehicles affected by this bulletin, a corrective measure is required due to bolts coming loose at the radiator...
Read full bulletin
fan clutch tripod attachment to the radiator. Addition of four (4) locknuts (jam nuts) will prevent bolts to loosen.
On the vehicles affected by this special bulletin, a 7psi pressure switch must be added to the transmission retarder...
Read full bulletin
circuit to activate the retarder when vehicle brakes are applied, increasing drivetrain components reliability.
On the vehicles affected by this bulletin, a software update for the Volvo I-Shift transmission is required.
Read full bulletin
Software update has for effect to improve the gear change process to avoid clashing and wear on the split gear. This software update is necessary on all I-shift transmission up to but not including serial number 1100224372.
Lighting
4 bulletinsHalogen to LED fog light replacement kit.
Read full bulletin
Revision: C - Advanced kits canceled
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S
This Maintenance Information reminds Prevost customers that cleaning products designed for external washing of vehicles...
Read full bulletin
should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
PREVOST: TO INCREASE VEHICLE'S PERFORMANCE, A MODIFICATION OF HOSE CLAMP FOR COOLING SYSTEM CONNECTION, IS RECOMMENDED.
Read full bulletin
MODELS 2010-13 H3, 2010-13 H3 VIP CONVERTED, 2010-13 X3, 2012-13 X3 VIP CONVERTED, 2010-13 MTH XL2 ENTERTAINER, 2011 MTH XL2 CONVERTED. *PE
Suspension
4 bulletinsTAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
RONT & TAG AXLE UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
Check that the pantograph arm does not interfere with gas spring in "door closed" position.
Rear fender support arm & WCL door spring replacement.
Software & Calibration
3 bulletinsAir Tanks Draining Sequence.
Read full bulletin
Revision: B - General Update
STORAGE AND STARTUP GUIDELINES : part number updates
This Maintenance Information explains that decals are available to update the front junction box on 2013 to 2016 Prevost...
Read full bulletin
vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of this bulletin to locate the decal part number currently used on specific vehicles.
Brakes
2 bulletinsPREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR10 TO FLR21 RADAR SENSOR UPGRADE
On the vehicles affected by this bulletin, take the following measure to improve dust handling.
Read full bulletin
Seal the evaporator compartment to prevent dust entry, add ribs inside the duct to prevent collapse by the weight of accumulated dust, modify the trim molding above the evaporator door opening, and remove the additional mud pad under the vehicle.
Infotainment
2 bulletinsMP-1000 MULTIMEDIA PLAYER INSTALLATION
This instruction sheet explains how to install latest radio models
Hybrid & EV
1 bulletinSTORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed ...
Read full bulletin
611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
Tires & Wheels
1 bulletinThis instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles...
Read full bulletin
with the air dryer located into the wheel pit .