2015 Prevost X3-45 TSBs
200 Technical Service Bulletins across 16 categories
Categories
Other
47 bulletinsThe gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously...
Read full bulletin
made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
Air Tanks Draining Sequence.
Read full bulletin
Revision: A - Erroneous Secondary & Accessory tanks location.
Air Tanks Draining Sequence
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
Communication letter from Accociate Administration for Enforcement, NHTSA From Prevost Subject Vehicle Brand: Prevost...
Read full bulletin
(EWR#000650)
On the vehicles affected by this bulletin, replace the AHI dozer by an improved part preventing nozzle clogging.
This Instruction Sheet explains how to add Sunshade Switches on the Dashboard
PREVOST VEHICLE DISINFECTION PROCEDURE Revision A
Accessory air filter replacement Replaces 642192
Repair instructions to address fault codes P20E892 Reductant Pressure Too Low - Performance orincorrect operation
Repair instructions to address fault codes P203F00 Reductant Level Low
Repair instructions to address fault codes P10CE97 Reductant Return: No Flow Detected - Componentor System Operation...
Read full bulletin
Obstructed or Blocked
Repair instructions to address fault codes P029800
Repair instructions to address fault codes P207F-00; P20EE-00
Repair instructions to address fault codes P207F-00 - Reductant Quality
Repair instructions to address fault codes P008A-00; P0087-00
PREVOST VEHICLE DISINFECTION PROCEDURE
HAND SANITIZER DISPENSER INSTALLATION
On the vehicles affected by this bulletin, replace the horn support by 140034.
This Instruction Sheet prvides a Road Side and Workshop Instructions for Replacing 040949 6mm DEF Hose to a 4mm ID Hose.
On the vehicles affected by this bulletin, replace the two auxiliary equipment decals in the first two road side parcel...
Read full bulletin
rack compartments.
On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube.
Read full bulletin
If it is made of black material (EDPM), replace tube. Green and blue silicone hoses are accepted.
On the vehicles affected by this bulletin, inspect the side of the matte finish on the anti-glare shield
On the vehicles affected by this bulletin, add caps on openings at front structure bottom corners.
On the vehicles affected by this bulletin, perform the replacement of the kneeling alarm buzzer assembly.
On the vehicles affected by this bulletin, inspect the driver's seat base to make sure specific nuts are properly...
Read full bulletin
tightened.
On the vehicles affected by this bulletin, Inspect the lower Oil fill tube flexible tube.
Read full bulletin
If it is made of black material, replace tube. Green and blue silicone hoses are accepted.
On the vehicles affected by this bulletin, replace the radiator fan driveshaft by an improved version having a stronger...
Read full bulletin
rubber protector.
On the vehicles affected by this bulletin, replace hardware on the aisle step curb side nosing.
On the vehicles affected by this bulletin, add an extrusion to the wiper arms to support the washer fluid hose.
On the vehicles affected by this bulletin, replace the two auxiliary equipment decals in the first two road side parcel...
Read full bulletin
rack compartments.
On the vehicles affected by this bulletin, five foot switches might be working intermittently and needs to be replaced.
On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube.
Read full bulletin
If it is made of black material (EDPM), replace tube. Green and blue silicone hoses are accepted.
On the vehicles affected by this bulletin, add an extrusion to the wiper arms to prevent washer fluid hose from...
Read full bulletin
pinching
On the vehicles affected by this bulletin, change the lower blind guide supports for a new style with two anchor screws.
On the vehicles affected by this bulletin, inspect the side of the matte finish on the anti-glare shield
On the vehicles affected by this bulletin, inspect the driver's seat base to make sure specific nuts are properly...
Read full bulletin
tightened.
ON THE VEHICLES AFFECTED BY THIS BULLETIN, REPLACE THE PITMAN ARM NUT AND RE-TORQUE TO SPECIFICATION.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PREVOST: DUE TO INTERMITTENTLY WORKING, THE FIVE FOOT SWITCHES, ON SOME BUSES, WILL BE REPLACED.
Read full bulletin
MODEL 2014-15 X3-45. *PE
Electrical
46 bulletinsELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR.
Read full bulletin
REVISION: E Note added regarding power cable connection
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR.
Read full bulletin
REVISION: E Note added regarding power cable connection
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good...
Read full bulletin
working order, perform the steps which follow to help you perform a more precise diagnosis.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR Revision B: Parts obsolete: 050303, 391028, 562112 ...
Read full bulletin
Replaced by: 830165 24V RED TELLTALE LIGHT MODULE QTY: 1x 381594 BRACKET, TELLTALE QTY:1x 561540 TAB TERMINAL, ST,16-14,1/4 INS QTY: 2x
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR REVISION : B Parts obsolete: 050303, 391028,...
Read full bulletin
562112 Replaced by: 830165 24V RED TELLTALE LIGHT MODULE QTY: 1x 381594 BRACKET, TELLTALE QTY:1x 561540 TAB TERMINAL, ST,16-14,1/4 INS QTY: 2x
Repair instructions to address fault codes U02A200 Lost Communication with Reductant Quality Module
Repair instructions to address fault codes U029E00 Lost Communication With NOx Sensor "B"
Repair instructions to address fault codes U029D00 Lost Communication With NOx Sensor "A"
Repair instructions to address fault codes P242A15 Exhaust Gas Temperature Sensor Bank 1 Sensor 3 - Circuit Short To...
Read full bulletin
Battery or Open
Repair instructions to address fault codes P208464 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1...
Read full bulletin
Sensor 2 - Signal plausibility failure
Repair instructions to address fault codes P204A13 Reductant Pressure Sensor - Circuit Open
Repair instructions to address fault codes P203115 Exhaust Gas Temperature Sensor Bank 1 Sensor 2 - Circuit Short To...
Read full bulletin
Battery or Open
Repair instructions to address fault codes P054415 Exhaust Gas Temperature Sensor Bank 1 Sensor 1 - Circuit Short To...
Read full bulletin
Battery or Open
Added: Power cables for L.H.
Read full bulletin
side alternator & fan drive breaker box
This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
This instruction sheet explains how to perform alternator conversion, from Bosch to Delco Remy, on X3 vehicles
This instruction sheet explains how to perform alternator conversion, from Bosch to Delco Remy, on X3 vehicles
This Maintenance Information presents how to install and remove the BOSCH HD10 ALTERNATOR
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors.
Read full bulletin
Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
On the vehicles affected by this bulletin, the voltage rating of the condenser / separator coil may be inappropriate for our application.
Read full bulletin
Our application is 24V.
On the vehicles affected by this bulletin, the Bosch HD10 alternators need to be replaced with new Bosch HD10PLBH 150...
Read full bulletin
Amps alternators.
On the vehicles affected by this bulletin, install a diffuser pipe thermal insulating wrap to promote higher exhaust...
Read full bulletin
temperature at the AHI nozzle tip.
On the vehicles affected by this bulletin, the end of the exhaust diffuser drain tube may not be properly attached.
On the vehicles affected by this bulletin, the end of the exhaust diffuser drain tube may not be properly attached.
On the vehicles affected by this bulletin, protect the A/C suction hose (Issue "A") and modify the pipe clamp...
Read full bulletin
arrangement above the battery box (Issue "B").
On the vehicles affected by this bulletin, the Bosch HD10 alternators need to be replaced with new Bosch HD10PLBH 150...
Read full bulletin
Amps alternators.
On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment...
Read full bulletin
and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacturer as having a calibration outside specifications.
This Maintenance Inforamtion presents how to install and remove the BOSCH HD10 ALTERNATOR
On the vehicles affected by this bulletin, tighten the alternator return pulley mounting bolt to a specific torque.
On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment...
Read full bulletin
and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacturer as having a calibration outside specifications.
On the vehicles affected by this bulletin, inspect fare box harness connector A132B pin out.
This bulletin explains how install an extension to the linear thermal detector (LTD) over the alternators
New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost...
Read full bulletin
vehicles.
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors.
Read full bulletin
Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
On the vehicles affected by this bulletin, replace the battery box decals.
On the vehicles affected by this bulletin, install a diffuser pipe thermal insulating wrap to promote higher exhaust...
Read full bulletin
temperature at the AHI nozzle tip.
On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment...
Read full bulletin
and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacturer as having a calibration outside specifications.
On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment...
Read full bulletin
and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacturer as having a calibration outside specifications.
On the vehicles affected by this bulletin, protect the A/C suction hose (Issue "A") and modify the pipe clamp...
Read full bulletin
arrangement above the battery box (Issue "B").
ON THE VEHICLES AFFECTED BY THIS BULLETIN, VIBRATION IS CAUSING DAMAGE TO A/C COMPRESSOR AND COMPRESSOR HARNESS CONNECTORS.
Read full bulletin
ADDITION OF A REINFORCEMENT BRACKET TO BITZER A/C COMPRESSOR IS NEEDED TO INCREASE THE INSTALLATION STIFFNESS AND REDUCE VIBRATION AMPLITUDE.
Engine
33 bulletinsKIT POWER STEERING TANK CONVERTION CUMMINS TO ZF WITH D13 ENGINE
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair From US10 to newer engine generation
Bendix M-32QR ABS modulator valve replaced by new M-40QR valve.
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
ENGINE OIL & FILTER CHANGE INTERVALS - VOLVO D13 ENGINE, FROM US10 Revision: A Updated for OBD20 engines
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 US20...
Read full bulletin
Emissions
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 US20...
Read full bulletin
Emissions
Repair instructions to address fault codes P040200 Engine Exhaust Gas Recirculation 1 Valve PositionFlow Excessive...
Read full bulletin
Detected
Repair instructions to address fault codes P256000 Engine Coolant Level Low
Repair instructions to address fault codes P204713 Reductant Injection Valve Control Bank 1 Unit 1 Circuit Open
Repair instructions to address fault codes P107017 Gearbox Brake Valve (VAGB) - Circuit voltage above threshold
Repair instructions to address fault codes P052400 Engine Oil Pressure Too Low
Repair instructions to address fault codes P040200 Engine Exhaust Gas Recirculation 1 Valve PositionFlow Excessive...
Read full bulletin
Detected
Repair instructions to address fault codes P021700 Engine Coolant Over Temperature Condition
This instruction sheet explains how to install the Electric Cooling System Conversion kit (with Delco Remy Alternators)...
Read full bulletin
on X3 vehicles equipped with US10 up to GHG17 Engine.
On the vehicles affected by this bulletin, the T-Key cylinder lock must be disassembled and lubricated, the latch pin...
Read full bulletin
inspected for damage and replaced as required. The upper and lower door stops must also be inspected if found broken or missing.
This instruction sheet explains how to install the Electric Cooling System Conversion kit (with Delco Remy Alternators)...
Read full bulletin
on X3 vehicles equipped with US10 up to GHG17 Engine.
On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is...
Read full bulletin
displaying incorrect information regarding the R34 relay voltage. Specifically, the R34 relay should be identified as a 24 volt relay instead of a 12 volt relay. Consequently, all affected vehicles must have a small decal displaying the correct information applied over the rear junction box decal R34 relay description.
This Instruction Sheet explains how to install a "T" Key on curbside Engine Compartment Door
On the vehicles affected by this bulletin the EPA (US Environment Protection Agency) decal located in the engine...
Read full bulletin
compartment displays incorrect information related to the vehicle emission control. Specifically, the first character, indicating the model year in the vehicle family identification number is incorrect and the California state EPA compliance notice is missing.
On the vehicles affected by this bulletin, ?Fast idle? and ?Cancel First Reading Lamp? switches on the dashboard may not...
Read full bulletin
be wired to provide back-lighting. Modify the wiring to add the feature.
On the vehicles affected by this bulletin, perform software updates of the Engine Management System (EMS) and instrument cluster.
Read full bulletin
The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles need either one update. Refer to table below.
On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may...
Read full bulletin
come in contact with an air reservoir outlet when vehicle rises from Low to High Buoy. As a result, the vehicle may be leveled higher in "Normal" position. The interference is corrected by changing the side on which the rod is attached to the linkage.
On the vehicles affected by this bulletin, connect a tube and muffler to the kneeling valve exhaust and route it to the...
Read full bulletin
spare tire compartment.
On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM...
Read full bulletin
(Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.
Explains that improved bearings are now available to replace the original bearings used on some Prevost vehicles idler...
Read full bulletin
pulleys.
On the vehicles affected by this bulletin, perform software updates of the Engine Management System (EMS) and instrument cluster.
Read full bulletin
The cluster update affects the beep sound level. Some vehicles will need both systems updated. Other vehicles need either one update. Refer to table below.
On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may...
Read full bulletin
come in contact with an air reservoir outlet when vehicle rises from Low to High Buoy. As a result, the vehicle may be leveled higher in "Normal" position. The interference is corrected by changing the side on which the rod is attached to the linkage.
"THIS MAINTENANCE INFORMATION DESCRIBES THE STEPS TO BE FOLLOWED ON YOUR COMPUTER TO ADD THE VOLVO ENGINE BRAKE AUTO MODE ON THE VEHICLE.
Read full bulletin
THE AUTO MODE MAY BE ADDED ON US10 AND OBD13 VEHICLES THAT WERE BUILT BEFORE THE INTRODUCTION OF THE VOLVO ENGINE BRAKE AUTO MODE ON THE ASSEMBLY LINE. THE VEHICLE MUST BE EQUIPPED WITH THE ALLISON TRANSMISSION AND VOLVO ENGINE BRAKE (VEB)."
PREVOST: WARRANTY ISSUED, ON SOME BUSES, REGARDING CONTROL ROD OF INDEPENDENT FRONT SUSPENSION LEVEL VALVE, CONTACTING ...
Read full bulletin
AIR RESERVOIR OUTLET WHEN GOING LOW TO HIGH BUOY. MODEL 2012-15 X3-45. *PE
Body & Paint
13 bulletinsWheeflchair lift cable wear - On the vehicles affected by this bulletin, it is possible to have premature wear of the...
Read full bulletin
WCL power cable caused by friction against the access panel,
AUTOMATIC FIRE SUPPRESSION SYSTEM - TAMPER SEAL REPLACEMENT
Plexiglass Panel Behind Driver X3
On the vehicles affected by this bulletin, replace the hardware on the sliding door of the wheelchair seating area.
On the vehicles affected by this bulletin, the windshield washer bottle may not be identified.
On the vehicles affected by this bulletin, replace the hardware on the sliding door of the wheelchair seating area.
On the vehicles affected by this bulletin, the entrance door may open inadvertently or not open at all when door open...
Read full bulletin
button is pressed.
On the vehicles affected by this bulletin, inspect the rear bumper, adjust and trim according to instructions.
On the vehicles affected by this bulletin, replace washers on the front bumper mountings.
On the vehicles affected by this bulletin, perform various improvements on the bi-fold door mechanism.
On the vehicles affected by this bulletin, it is possible to have premature wear of the WCL power cable caused by...
Read full bulletin
friction against the access panel.
PREVOST: ON SOME BUSES, THE BI-FOLD DOOR MECHANISM NEEDED VARIOUS IMPROVEMENTS PERFORMED ON IT.
Read full bulletin
MODEL 2014-15 X3-45. *PE
PREVOST: WHEN BUTTON TO DOOR IS PRESSED TO OPEN, ENTRANCE DOOR, ON SOME BUSES, INADVERTENTLY, WILL OPEN AND NOT OPEN AT ALL.
Read full bulletin
MODEL 2014-15 X3-45. *PE
Suspension
10 bulletinsSway bar collars improvement.
Read full bulletin
Revision A : Add front sway bar support replacement and change bolts lenght.
SWAY BAR COLLARS IMPROVEMENT
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
RONT & TAG AXLE UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
On the vehicles affected by this bulletin, replace the front axle wheel hub bearing unit with an improved version.
On the vehicles affected by this bulletin, replace the hardware on the sway bar clamps of the steer and drive axles.
On the vehicles affected by this bulletin, replace the hardware on the sway bar clamps of the steer and drive axles.
On the vehicles affected by this bulletin, modify the hubodometer support to allow the wheel to be taken out without...
Read full bulletin
removing the support.
On the vehicles affected by this bulletin, replace the front bumper retaining spring.
PREVOST: INFORMATION PROVIDED ON CERTAIN BUSES, THE SWAY BAR CLAMPS OF STEER AND DRIVE AXLES NEED HARDWARE REPLACED.
Read full bulletin
MODEL 2014-15 X3-45 COMMUTER. *PE
Steering
9 bulletinsSTEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles.
Read full bulletin
The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
Vehicles identified below are compatible with a new tie rod design.
Read full bulletin
This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
POWER STEERING PUMP DISCHARGE HOSE (PRESSURE) REPLACEMENT
This instruction sheet explains how to perform the replacement of the power steering pump discharge hose (PRESSURE)...
Read full bulletin
#161335P or #160039, using kit #160127;
On the vehicles affected by this bulletin, replace the power steering supply hose.
PREVOST: THE SUPPLY HOSE FOR POWER STEERING NEEDS BE REPLACED ON SOME BUSES.
Read full bulletin
MODEL 2014-15 X3-45. *PE
Brakes
9 bulletinsBRAKE PEDAL SEAL PLATE INSTALLATION KIT
PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT KIT Revision A: KIT IS13169-1 & IS13169-2...
Read full bulletin
CANCELED, USE 145373 &145372
PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) - FLR20 & FLR21 RADAR SENSOR ALIGNMENT
On the independent front suspension (IFS) of the vehicles affected by this bulletin, check and make sure that there is...
Read full bulletin
enough clearance between the brake hoses identified in the procedure and their respective support bracket.
On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when vehicle is in low or high buoy position.
Read full bulletin
Perform an inspection. Depending on the result, adjust the hoses to avoid any interference.
On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front...
Read full bulletin
axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, adjust the hoses to avoid any interference.
On the vehicles affected by this bulletin inspect the clamp retaining the brake hose supports to make sure it does not...
Read full bulletin
contact with the shock absorber.
On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front...
Read full bulletin
axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, adjust the hoses to avoid any interference.
PREVOST: WHEN BUS IN POSITION OF LOW OR HIGH BUOY, BRAKE HOSE WILL CONTACT AIR SPRING SUPPORT AND WOULD NEED INSPECTED...
Read full bulletin
AND ADJUSTED, FOR HOSE TO NOT INTERFERE. MODEL 2012-15 X3-45. *PE
Transmission
8 bulletinsVOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX.
Read full bulletin
HYDRAULIC END LIMITER ADJUSTMENT. All models equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
Repair instructions to address fault codes P107575 Clutch System - Emergency position not reachable
Repair instructions to address fault codes P105998 Gearbox Oil Temperature Sensor - Component orsystem over temperature
NEUTRAL GEAR - SOFTWARE UPDATE
This Maintrenance infomration explains that the Castrol Syntrans oil isn?t fully approved for 500 000 miles (800 000 km)...
Read full bulletin
extended drain intervals on the Volvo I-Shift transmission. For this reason, this oil has been downgraded to regular drain intervals. Find below, a list of Volvo?s approved oils for extended drain as well as regular drain intervals.
On the vehicles affected by this bulletin, inspect the coolant hose flexible elbow and piping arrangement on the...
Read full bulletin
transmission cooler.
HVAC & Climate
6 bulletinsCENTRAL HVAC MERV FILTERS INSTALLATION
EBERSPACHER PREHEATER INSTALLATION In replacement of Spheros & Valeo preheaters
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
UV LIGHTS INSTALLATION IN A/C COMPARTMENT
This Maintenance Information explains how to run a n Air Conditionning performance test
On the vehicles affected by this bulletin, seal a tube passage between the Auxiliary heater compartment and the heating...
Read full bulletin
duct in the passenger's compartment.
Software & Calibration
5 bulletinsAir Tanks Draining Sequence.
Read full bulletin
Revision: B - General Update
STORAGE AND STARTUP GUIDELINES : part number updates
On the vehicles affected by this bulletin, perform a software update of the Actia Tachometer at the rear of the vehicle.
On the vehicles affected by this bulletin, replace sun visor on the left side of the driver?s seat by an updated...
Read full bulletin
version.
On the vehicles affected by this bulletin, replace sun visor on the left side of the driver's seat by an updated...
Read full bulletin
version.
Fuel System
5 bulletinsThis instruction sheet shows how to install a flap over the diesel filling cap.
This instruction sheet shows how to install a flap over the diesel filling cap.
This instruction sheet shows how to install a flap over the diesel filling cap.
On the vehicles affected by this bulletin, two DPF (diesel particulate filter) plugs may be loose.
Read full bulletin
If a plug is loose, it may fall under the effect of vibration. This may cause leakage of hot exhaust gases. It is therefore necessary to check if the plugs are tight and to tighten them properly if applicable.
On the vehicles covered by this bulletin, two DPF (diesel particulate filter) plugs may be loose.
Read full bulletin
If a plug is loose, it may fall out under the effect of vibration. This may cause leakage of hot exhaust gases. It is therefore necessary to check if the plugs are tight and to tighten them properly if applicable.
Pre-Delivery & Maintenance
3 bulletinsSTORAGE AND STARTUP GUIDELINES: Periodically, circumstances arise requiring operators to temporarily park a coach in storage.
Read full bulletin
Whether it is a few weeks or several months, sporadic out of service times or a full stop, Prevost recommends following the guidelines in this document during times when: The coach can be operated on a regular/weekly basis while in storage. The coach will be in storage for an extended period without any operation. The coach will return to service following an extended period of downtime.
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
Lighting
2 bulletinsHalogen to LED fog light replacement kit.
Read full bulletin
Revision: C - Advanced kits canceled
UV LIGHTS INSTALLATION IN AC COMPARTMENT
Hybrid & EV
2 bulletinsOn the vehicles affected by this bulletin, it is necessary to perform a Multiplex software update plus other corrective...
Read full bulletin
measures to improve the charging system. The corrective measures of this bulletin are very important and must all be carried out on the involved vehicles.
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed ...
Read full bulletin
611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
Tires & Wheels
1 bulletinRevision : Mention added stating to disable Prime & parts added in the kit.
Air Bags & Safety
1 bulletinThis instruction Sheet explains how to install a seatbelt cutter in the driver's area