2013 Prevost X3-45 TSBs
127 Technical Service Bulletins across 17 categories
Categories
Electrical
34 bulletinsELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR.
Read full bulletin
REVISION: E Note added regarding power cable connection
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR.
Read full bulletin
REVISION: E Note added regarding power cable connection
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good...
Read full bulletin
working order, perform the steps which follow to help you perform a more precise diagnosis.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR
Sound Selector replacement, VSS04 to VSS05; When replacing a vehicle sound selector model VSS04 with a new sound...
Read full bulletin
selector model VSS05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR
After the installation of the latest Multiplex system update on US10 X3-Series coaches, the instrument panel and...
Read full bulletin
switches backlighting may stay constantly on due to an output (J1:4) on the A44 module sending constant current to the 114A circuit via the 2mph wire. This wire should be connected only for Commuter application and must be removed on coaches. To retain gateway module watchdog timer (WDT) function, a new wire must be routed and connected between module A44 output and the Gateway module.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR Revision B: Parts obsolete: 050303, 391028, 562112 ...
Read full bulletin
Replaced by: 830165 24V RED TELLTALE LIGHT MODULE QTY: 1x 381594 BRACKET, TELLTALE QTY:1x 561540 TAB TERMINAL, ST,16-14,1/4 INS QTY: 2x
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR REVISION : B Parts obsolete: 050303, 391028,...
Read full bulletin
562112 Replaced by: 830165 24V RED TELLTALE LIGHT MODULE QTY: 1x 381594 BRACKET, TELLTALE QTY:1x 561540 TAB TERMINAL, ST,16-14,1/4 INS QTY: 2x
Repair instructions to address fault codes U02A200 Lost Communication with Reductant Quality Module
Repair instructions to address fault codes U029E00 Lost Communication With NOx Sensor "B"
Repair instructions to address fault codes U029D00 Lost Communication With NOx Sensor "A"
Repair instructions to address fault codes P242A15 Exhaust Gas Temperature Sensor Bank 1 Sensor 3 - Circuit Short To...
Read full bulletin
Battery or Open
Repair instructions to address fault codes P208464 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1...
Read full bulletin
Sensor 2 - Signal plausibility failure
Repair instructions to address fault codes P204A13 Reductant Pressure Sensor - Circuit Open
Repair instructions to address fault codes P203115 Exhaust Gas Temperature Sensor Bank 1 Sensor 2 - Circuit Short To...
Read full bulletin
Battery or Open
Repair instructions to address fault codes P054415 Exhaust Gas Temperature Sensor Bank 1 Sensor 1 - Circuit Short To...
Read full bulletin
Battery or Open
Added: Power cables for L.H.
Read full bulletin
side alternator & fan drive breaker box
This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
This instruction sheet explains how to install Delco Remy Alternators
On the vehicles affected by this bulletin, to reduce the possibility of fault codes the DPF differential pressure sensor...
Read full bulletin
signal wire needs to be replaced by a single wire from the DPF differential pressure sensor directly to the ACM connector.
To correct the J-1939 CAN2 and Nox sensor faults that have been intermittently logging, a dedicated CAN harness cable...
Read full bulletin
(twisted wires) will run from connector C26 near the ACM in the condenser compartment to the splice bar connector S-bar 1 at the rear of the bus
On the vehicles affected by this bulletin, inspect the Bosch HD10 alternator connections.
New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost...
Read full bulletin
vehicles.
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors.
Read full bulletin
Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
ON THE VEHICLES AFFECTED BY THIS BULLETIN, VIBRATION IS CAUSING DAMAGE TO A/C COMPRESSOR AND COMPRESSOR HARNESS CONNECTORS.
Read full bulletin
ADDITION OF A REINFORCEMENT BRACKET TO BITZER A/C COMPRESSOR IS NEEDED TO INCREASE THE INSTALLATION STIFFNESS AND REDUCE VIBRATION AMPLITUDE.
WHEN REPLACING A VEHICLE SOUND SELECTOR MODEL VSS04 WITH A NEW SOUND SELECTOR MODEL VSS05, AN INTERFACE HARNESS IS...
Read full bulletin
REQUIRED TO CONNECT THE VEHICLE HARNESS TO THE NEW SOUND SELECTOR MODEL AND A NEW VSS05 COMPATIBLE RADIO UNIT MUST ALSO BE INSTALLED. THIS PROCEDURE DESCRIBES THE STEPS REQUIRED TO PERFORM THIS UPDATE.
PREVOST: BOSCH HD 10 ALTERNATOR CONNECTIONS, ON SOME BUSES, NEED TO BE INSPECTED AND MAY NEED OTHER PARTS AND MATERIALS, IF REQUIRED.
Read full bulletin
MODEL 2011-14. *PE
PREVOST: THE COMBINED CHARGING AND STARTING SYSTEM F81 FUSE, ON SOME COACHES, CAN UNEXPECTEDLY BLOW AND NEED A 3 AMP...
Read full bulletin
DIODE TO CORRESPONDING 24CO CIRCUIT TO PREVENT ELECTRICAL BACK FLOW TO FUSE. MODELS 2011-2013 H3, H3-45 VIP CONVERTED, X3-45, X3-45 VIP CONVERTED, XL2-45 ENTERTAINER CONVERTED. *PE
PREVOST: THE NOX SENSOR MUST BE REPLACED AND THE EMS SOFTWARE NEEDS UPDATING TO CORRECT EMISSIONS INSPECTIONS ON CERTAIN COACHES.
Read full bulletin
MODELS 2012-2013 H3-45, H3 VIP, X3-45, LE MIRAGE XLII. *PE
PREVOST: POWER IS NOT REMOVED WHEN UNPLUGGING FUSE F45 TO FIRE PROTECTION PANEL ON DRIVER'S LEFT CONSOLE WHERE...
Read full bulletin
MODIFICATION OF HARNESS MUST BE PERFORMED. MODELS 2012-2013 H3-41, H3-45, X3-45, XLII-45 (COACH, COMMUTER & VIP SHELL). *PE
Engine
30 bulletinsKIT POWER STEERING TANK CONVERTION CUMMINS TO ZF WITH D13 ENGINE
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair From US10 to newer engine generation
Bendix M-32QR ABS modulator valve replaced by new M-40QR valve.
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
ENGINE OIL & FILTER CHANGE INTERVALS - VOLVO D13 ENGINE, FROM US10 Revision: A Updated for OBD20 engines
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 US20...
Read full bulletin
Emissions
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 US20...
Read full bulletin
Emissions
Repair instructions to address fault codes P040200 Engine Exhaust Gas Recirculation 1 Valve PositionFlow Excessive...
Read full bulletin
Detected
Repair instructions to address fault codes P256000 Engine Coolant Level Low
Repair instructions to address fault codes P204713 Reductant Injection Valve Control Bank 1 Unit 1 Circuit Open
Repair instructions to address fault codes P107017 Gearbox Brake Valve (VAGB) - Circuit voltage above threshold
Repair instructions to address fault codes P052400 Engine Oil Pressure Too Low
Repair instructions to address fault codes P040200 Engine Exhaust Gas Recirculation 1 Valve PositionFlow Excessive...
Read full bulletin
Detected
Repair instructions to address fault codes P021700 Engine Coolant Over Temperature Condition
This instruction sheet explains how to install the Electric Cooling System Conversion kit (with Delco Remy Alternators)...
Read full bulletin
on X3 vehicles equipped with US10 up to GHG17 Engine.
This instruction sheet explains how to install the Electric Cooling System Conversion kit (with Delco Remy Alternators)...
Read full bulletin
on X3 vehicles equipped with US10 up to GHG17 Engine.
On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is...
Read full bulletin
displaying incorrect information regarding the R34 relay voltage. Specifically, the R34 relay should be identified as a 24 volt relay instead of a 12 volt relay. Consequently, all affected vehicles must have a small decal displaying the correct information applied over the rear junction box decal R34 relay description.
On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may...
Read full bulletin
come in contact with an air reservoir outlet when vehicle rises from Low to High Buoy. As a result, the vehicle may be leveled higher in "Normal" position. The interference is corrected by changing the side on which the rod is attached to the linkage.
On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM...
Read full bulletin
(Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.
Explains that improved bearings are now available to replace the original bearings used on some Prevost vehicles idler...
Read full bulletin
pulleys.
On the independent front suspension level valve linkage of the vehicles affected by this bulletin, a control rod may...
Read full bulletin
come in contact with an air reservoir outlet when vehicle rises from Low to High Buoy. As a result, the vehicle may be leveled higher in "Normal" position. The interference is corrected by changing the side on which the rod is attached to the linkage.
"THIS MAINTENANCE INFORMATION DESCRIBES THE STEPS TO BE FOLLOWED ON YOUR COMPUTER TO ADD THE VOLVO ENGINE BRAKE AUTO MODE ON THE VEHICLE.
Read full bulletin
THE AUTO MODE MAY BE ADDED ON US10 AND OBD13 VEHICLES THAT WERE BUILT BEFORE THE INTRODUCTION OF THE VOLVO ENGINE BRAKE AUTO MODE ON THE ASSEMBLY LINE. THE VEHICLE MUST BE EQUIPPED WITH THE ALLISON TRANSMISSION AND VOLVO ENGINE BRAKE (VEB)."
PREVOST: WARRANTY ISSUED, ON SOME BUSES, REGARDING CONTROL ROD OF INDEPENDENT FRONT SUSPENSION LEVEL VALVE, CONTACTING ...
Read full bulletin
AIR RESERVOIR OUTLET WHEN GOING LOW TO HIGH BUOY. MODEL 2012-15 X3-45. *PE
PREVOST: ON SOME BUSES, BY VIN, WILL HAVE INSTALLED THE J-1939 CAN2 ENGINE SUBNET CABLE OVERLAY, DUE TO INTERMITTENT LOGGING.
Read full bulletin
MODEL 2011-13 X3-45. *PE
PREVOST: INFORMATION REGARDING BASE OF THE MASTER RELAY INSTALLED, SHOWING SIGNS OF CORROSION, IN THE VEHICLE BATTERY...
Read full bulletin
BOX OF COACHES 2010-2013, ENTERTAINER 2011-2013 AND VIP MOTORHOMES 2012-2013. *LJ
PREVOST: IF RUBBING FOUND ON 4 INCH OD TURBO OUTLET PIPE, AFTER CLOSING SUPPORT BRACKET, THEN TO INCREASE CLEARANCE...
Read full bulletin
BETWEEN INVOLVED COMPONENTS, A MODIFICATION OF SUPPORT BRACKET MUST BE PERFORMED. NO MODEL OR MODEL YEARS LISTED. *PE MODELS 2011-2013 X3-45, XLII SHELLS, X3-45 VIP SHELLS. UPDATED 3/21/13. *PE
PREVOST: CORRECTIVE MEASURE FOR THE EGR VALVE IS NECESSARY BECAUSE OF THE UNNECESSARY PRESENCE OF O-RINGS, WHICH MAY PREVENT FREE VALVE ACTUATION.
Read full bulletin
EGR VALVE CAN BE REPLACED WITH LATEST VERSION. MODELS 2012-13 H3-41, H3-H45 COACHES, H3-45 VIP MOTORHOMES, X3-45 COACHES, XLII SHELLS, X3-45 VIP MOTORHOMES. *PE
Other
22 bulletinsThe gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously...
Read full bulletin
made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
Air Tanks Draining Sequence.
Read full bulletin
Revision: A - Erroneous Secondary & Accessory tanks location.
Air Tanks Draining Sequence
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
This Instruction Sheet explains how to add Sunshade Switches on the Dashboard
PREVOST VEHICLE DISINFECTION PROCEDURE Revision A
Repair instructions to address fault codes P20E892 Reductant Pressure Too Low - Performance orincorrect operation
Repair instructions to address fault codes P203F00 Reductant Level Low
Repair instructions to address fault codes P10CE97 Reductant Return: No Flow Detected - Componentor System Operation...
Read full bulletin
Obstructed or Blocked
Repair instructions to address fault codes P029800
Repair instructions to address fault codes P207F-00; P20EE-00
Repair instructions to address fault codes P207F-00 - Reductant Quality
Repair instructions to address fault codes P008A-00; P0087-00
PREVOST VEHICLE DISINFECTION PROCEDURE
HAND SANITIZER DISPENSER INSTALLATION
This Instruction Sheet prvides a Road Side and Workshop Instructions for Replacing 040949 6mm DEF Hose to a 4mm ID Hose.
On the vehicles affected by this bulletin, inspect the rear junction box connections; clean terminals and apply black...
Read full bulletin
Color Guard or Termin8R lubricant following the procedure below.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PREVOST: REAR JUNCTION BOX CONNECTIONS NEED INSPECTED WITH CLEAN TERMINALS AND TERMIN8R LUBRICANT OR BLACK COLOR GUARD...
Read full bulletin
SHOULD BE APPLIED FOLLOWING REQUIRED PROCEDURE. MODEL 2011-14 X3-45 (GLI). *PE
PREVOST: INFORMATION BEING PROVIDED REGARDING THE REPLACEMENT OF DIPSTICK ON CERTAIN COACHES.
Read full bulletin
MODELS 2009-2013 H3-45, H3-41, X3-45, XL11-45, X3-45. *PE
Steering
7 bulletinsSTEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles.
Read full bulletin
The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
Vehicles identified below are compatible with a new tie rod design.
Read full bulletin
This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
POWER STEERING PUMP DISCHARGE HOSE (PRESSURE) REPLACEMENT
This instruction sheet explains how to perform the replacement of the power steering pump discharge hose (PRESSURE)...
Read full bulletin
#161335P or #160039, using kit #160127;
Transmission
7 bulletinsVOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX.
Read full bulletin
HYDRAULIC END LIMITER ADJUSTMENT. All models equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
Repair instructions to address fault codes P107575 Clutch System - Emergency position not reachable
Repair instructions to address fault codes P105998 Gearbox Oil Temperature Sensor - Component orsystem over temperature
This Maintrenance infomration explains that the Castrol Syntrans oil isn?t fully approved for 500 000 miles (800 000 km)...
Read full bulletin
extended drain intervals on the Volvo I-Shift transmission. For this reason, this oil has been downgraded to regular drain intervals. Find below, a list of Volvo?s approved oils for extended drain as well as regular drain intervals.
PREVOST: A CORRECTIVE MEASURE IS REQUIRED DUE TO BOLTS LOOSEN BY BEING TIGHTENED TO PART MADE OF RUBBER, CAUSING THE...
Read full bulletin
RADIATOR FAN CLUTCH TRIPOD TO COME LOOSE AND STRIKING RADIATOR CORE. *PE
Suspension
4 bulletinsSway bar collars improvement.
Read full bulletin
Revision A : Add front sway bar support replacement and change bolts lenght.
SWAY BAR COLLARS IMPROVEMENT
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
RONT & TAG AXLE UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
HVAC & Climate
4 bulletinsCENTRAL HVAC MERV FILTERS INSTALLATION
EBERSPACHER PREHEATER INSTALLATION In replacement of Spheros & Valeo preheaters
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
This Maintenance Information explains how to run a n Air Conditionning performance test
Pre-Delivery & Maintenance
3 bulletinsSTORAGE AND STARTUP GUIDELINES: Periodically, circumstances arise requiring operators to temporarily park a coach in storage.
Read full bulletin
Whether it is a few weeks or several months, sporadic out of service times or a full stop, Prevost recommends following the guidelines in this document during times when: The coach can be operated on a regular/weekly basis while in storage. The coach will be in storage for an extended period without any operation. The coach will return to service following an extended period of downtime.
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
Body & Paint
3 bulletinsPlexiglass Panel Behind Driver X3
On the vehicles affected by this bulletin, to prevent premature corrosion of the rear junction box components, replace...
Read full bulletin
the junction box cover with a late model "central mount" cover.
PREVOST: ON SOME BUSES, THE JUNCTION REAR COMPONENT BOX COVER WOULD BE REPLACED TO PREVENT PREMATURE CORROSION.
Read full bulletin
MODEL X3-45. *PE
Fuel System
3 bulletinsThis instruction sheet shows how to install a flap over the diesel filling cap.
This instruction sheet shows how to install a flap over the diesel filling cap.
This instruction sheet shows how to install a flap over the diesel filling cap.
Brakes
3 bulletinsOn the independent front suspension (IFS) of the vehicles affected by this bulletin, check and make sure that there is...
Read full bulletin
enough clearance between the brake hoses identified in the procedure and their respective support bracket.
On the vehicles affected by this bulletin the brake hose may come in contact with the air spring support when the front...
Read full bulletin
axle is in low or high position, either by kneeling or low-high buoy. Perform an inspection. Depending on the result, adjust the hoses to avoid any interference.
PREVOST: WHEN BUS IN POSITION OF LOW OR HIGH BUOY, BRAKE HOSE WILL CONTACT AIR SPRING SUPPORT AND WOULD NEED INSPECTED...
Read full bulletin
AND ADJUSTED, FOR HOSE TO NOT INTERFERE. MODEL 2012-15 X3-45. *PE
Software & Calibration
2 bulletinsAir Tanks Draining Sequence.
Read full bulletin
Revision: B - General Update
STORAGE AND STARTUP GUIDELINES : part number updates
Lighting
1 bulletinHalogen to LED fog light replacement kit.
Read full bulletin
Revision: C - Advanced kits canceled
Hybrid & EV
1 bulletinSTORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed ...
Read full bulletin
611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
Tires & Wheels
1 bulletinRevision : Mention added stating to disable Prime & parts added in the kit.
Air Bags & Safety
1 bulletinThis instruction Sheet explains how to install a seatbelt cutter in the driver's area
Infotainment
1 bulletinMP-1000 MULTIMEDIA PLAYER INSTALLATION