2015 Prevost X3-45 Coach TSBs
51 Technical Service Bulletins across 14 categories
Categories
Other
12 bulletinsAir Tanks Draining Sequence.
Read full bulletin
Revision: A - Erroneous Secondary & Accessory tanks location.
Air Tanks Draining Sequence
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
Repair instructions to address fault codes P207F-00; P20EE-00
Repair instructions to address fault codes P207F-00 - Reductant Quality
Repair instructions to address fault codes P008A-00; P0087-00
PREVOST VEHICLE DISINFECTION PROCEDURE
ON THE VEHICLES AFFECTED BY THIS BULLETIN, REPLACE THE PITMAN ARM NUT AND RE-TORQUE TO SPECIFICATION.
ON THE VEHICLES AFFECTED BY THIS BULLETIN, MODIFY SPECIFIC PARAMETERS IN THE VEHICLE MULTIPLEX SYSTEM.
ON THE VEHICLES AFFECTED BY THIS BULLETIN, REPLACE THE PITMAN ARM NUT AND RE-TORQUE TO SPECIFICATION.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Electrical
9 bulletinsELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR.
Read full bulletin
REVISION: E Note added regarding power cable connection
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR.
Read full bulletin
REVISION: E Note added regarding power cable connection
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good...
Read full bulletin
working order, perform the steps which follow to help you perform a more precise diagnosis.
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
Added: Power cables for L.H.
Read full bulletin
side alternator & fan drive breaker box
Engine
8 bulletinsImproved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair From US10 to newer engine generation
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
Repair instructions to address fault codes P040200 Engine Exhaust Gas Recirculation 1 Valve PositionFlow Excessive...
Read full bulletin
Detected
ON THE VEHICLES AFFECTED BY THIS BULLETIN, PROCEED TO THE REPLACEMENT OF THE ORIGINAL A/C TENSIONER AND ALTERNATOR IDLER...
Read full bulletin
BEARINGS WITH A FAG BRANDED UNIT. THESE FAG BEARINGS ARE OF HEAVIER DUTY CONSTRUCTION AND WILL OFFER EXTENDED DURABILITY COMPARED TO THE ORIGINAL ONES.
"THIS MAINTENANCE INFORMATION DESCRIBES THE STEPS TO BE FOLLOWED ON YOUR COMPUTER TO ADD THE VOLVO ENGINE BRAKE AUTO MODE ON THE VEHICLE.
Read full bulletin
THE AUTO MODE MAY BE ADDED ON US10 AND OBD13 VEHICLES THAT WERE BUILT BEFORE THE INTRODUCTION OF THE VOLVO ENGINE BRAKE AUTO MODE ON THE ASSEMBLY LINE. THE VEHICLE MUST BE EQUIPPED WITH THE ALLISON TRANSMISSION AND VOLVO ENGINE BRAKE (VEB)."
Steering
4 bulletinsSTEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles.
Read full bulletin
The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
HVAC & Climate
3 bulletinsCENTRAL HVAC MERV FILTERS INSTALLATION
EBERSPACHER PREHEATER INSTALLATION In replacement of Spheros & Valeo preheaters
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
Pre-Delivery & Maintenance
3 bulletinsSTORAGE AND STARTUP GUIDELINES: Periodically, circumstances arise requiring operators to temporarily park a coach in storage.
Read full bulletin
Whether it is a few weeks or several months, sporadic out of service times or a full stop, Prevost recommends following the guidelines in this document during times when: The coach can be operated on a regular/weekly basis while in storage. The coach will be in storage for an extended period without any operation. The coach will return to service following an extended period of downtime.
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
Transmission
3 bulletinsVOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX.
Read full bulletin
HYDRAULIC END LIMITER ADJUSTMENT. All models equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
Software & Calibration
2 bulletinsAir Tanks Draining Sequence.
Read full bulletin
Revision: B - General Update
STORAGE AND STARTUP GUIDELINES : part number updates
Suspension
2 bulletinsTAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
RONT & TAG AXLE UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
Brakes
1 bulletinBRAKE PEDAL SEAL PLATE INSTALLATION KIT
Body & Paint
1 bulletinAUTOMATIC FIRE SUPPRESSION SYSTEM - TAMPER SEAL REPLACEMENT
Hybrid & EV
1 bulletinSTORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed ...
Read full bulletin
611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
Fuel System
1 bulletinThis instruction sheet shows how to install a flap over the diesel filling cap.
Lighting
1 bulletinRADIUS ROD SUPPORT AND I-BEAM AXLE GAP INSPECTION On the vehicles affected by this bulletin, inspect the gap between...
Read full bulletin
the radius rod support and the axle. A deviation in the axle beam envelope can lead to interference between the two parts. In most cases, slightly moving the support will resolve the issue. Exceptionally, the axle may need to be replaced.