2016 Nissan Titan TSBs

front differential has a fluid leak coming from the actuator motor plastic threads (Figure 1): a. Place an alignment mark on the splined actuator body and the gear carrier (Figure 2). b. Remove the actuator and thoroughly clean the threads, making sure not to allow RTV to fall into the differential case. c. Once clean, apply Three Bond sealant to the threads, and then reinstall the actuator motor, making sure to line up the alignment marks. d. Check the front differential gear oil level and top to specification. o Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > FRONT FINAL DRIVE: MA235/MA210 > PERIODIC MAINTENANCE > FRONT DIFFERENTIAL GEAR OIL DO NOT replace the front differential due to a fluid leak from the actuator motor plastic threads unless there has been consequential damage due to fluid loss (bearing failure or gear noise) to the front differential.

Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2016-2019 Titan XD vehicles with Diesel engines to inspect and, if necessary, replace the Vehicle Emission Control Information Label. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PD127 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealers inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

voluntary emissions recall campaign on certain specific model year 2016-2017 Titan XD vehicles equipped with a diesel engine, to install a Particulate Matter (PM) Sensor and reprogram the Engine Control Module (ECM). This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PD128 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealers inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

APPLIED VEHICLE has a fluid leak from the actuator motor body or threads (Figure 1), replace the actuator motor on the front differential case. DO NOT replace the front differential due to a fluid leak from the actuator motor unless there has been consequential damage due to fluid loss (bearing failure or gear noise) to the front differential.

Announcement***** Nissan is committed to providing the highest levels of product quality and customer satisfaction. Therefore, Nissan is extending the emission warranty coverage on MY16 Titan XD Titan Turbo Actuator and High-Pressure Turbocharger to 10 Years or 150,000 miles, whichever occurs first. All other warranty terms, limitations, and conditions remain unchanged. Certain MY16 TITAN XD Diesel vehicles may experience issues with the Turbo Actuator or the High-Pressure Turbocharger. Over time, a solder crack may develop in the Turbo Actuator and/or carbon build-up is possible on the High-Pressure Turbocharger Compressor. The most likely conditions are a MIL-On with DTC P00AF and/or DTC P0299. These issues have no effect on vehicle safety, drivability, or fuel economy. There could be a decrease in performance if either condition were to occur. During the limited emission warranty extension period, owners are eligible for free replacement of the Turbo Actuator and High-Pressure Turbocharger if either is determined to be required by a Nissan trained technician. Owners of eligible vehicles will receive notification of this limited emission warranty extension during November 2022. ***** What Dealers Should Do ***** 1. Verify if vehicles are eligible for this Warranty Extension using the warranty extension page of Service Comm. 2. If a customer contacts the dealer with a Turbo Actuator or High-Pressure Turbocharger concern in an owned or leased vehicle, dealers should use the appropriate Technical Service Bulletin (TSB) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

intrusion into one or both of the rear combination lamp assemblies can cause multiple DTCs, and possibly cause the vehicles engine to not start. Water intrusion into one or both rear combination lamp assemblies has been found to migrate through the harness, and can cause harness connector terminals in C1/E41 to corrode (Figure 1 on page 2). Repair any damaged rear combination lamp assemblies immediately to avoid potential harness damage. Notice Harness connector terminals in C1/E41 found to be damaged through water intrusion due to a damaged rear combination lamp assembly is not warrantable.

dealer inventory service action to update the Engine Control Module (ECM) software oin 3,334 specific 2016 Titan XD vehicles identified tin Service Comm. On the affected fvehicles, the software is being updated to refine the MIL illumination logic. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer.

temperature is around or below 0C (32F). NOTE - These recommendations are also found in the vehicle Owner?s Manual. - Always use the correct engine oil for the prevailing conditions. - Use an engine block heater (if so equipped) when the ambient temperature is at or below -18C (0F). - Engine block heaters are used to assist with cold temperature starting. - Some engine block heaters will operate continuously while plugged into the correct voltage electrical outlet. IMPORTANT: DO NOT use the engine block heater in temperature conditions at or above 0C (32F). Doing so may cause damage to the engine block heater. See this bulletin for further detail.

Timing * P021A - B: Cylinder 7 - 8 Injection Timing * P060C: Internal Control Module Main Processor Performance * P061B: Internal Control Module Torque Calculation Performance * P0605: ECM * P2048: Reductant Injector Circuit Low * P0299: Boost Pressure * P2263: Turbocharger Boost System Performance * P0401: Flow in the Exhaust Gas Recirculation (Insufficient) * P0402: Flow in the Exhaust Gas Recirculation (Excessive) * P2483: Exhaust Gas Temperature Sensor Circuit Intermittent 1/5 * P244D: Exhaust Temperature Too High For PF Regeneration * U0415: VDC CAN CIR2 * P2BAD: NOx Concentration Exceeded * P1C55: NOx Sensor 1/1 Intermittent * P1C56: NOx Sensor 1/2 Intermittent * P2201: NOx Sensor 1 and/or At times, when coming to a stop, the idle fluctuates with RPM dropping below 500 RPM. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus. See this bulletin for further detail.

first time (cold start), * and then before reaching operating temperature is driven outside in an ambient temperature below 0F (-18C). Then * A hesitation is present while accelerating that improves as engine temperature increases, and subsides when the engine reaches normal operating temperature. And/or * The vehicle is operated in ambient temperatures at orbelow32F (0C) and one of these codes are stored. * P202E - Reductant Injection Valve Circuit 1/1 * P218F - Reductant No Flow Detected * P22CE - TC Outlet Switching Valve Stuck Closed Please see this bulletin for further details.

Incorrect Ratio P0730: Incorrect Gear Ratio P0731: 1GR Incorrect Ratio P0732: 2GR Incorrect Ratio P0733: 3GR Incorrect Ratio P0734: 4GR Incorrect Ratio P0735: 5GR Incorrect Ratio P1734: 7GR Incorrect Ratio Before performing any transmission repairs: 1. Check all of the engine intake air ducting and make sure: - It is connected securely and correctly at the throttle body and all other connections. See Figures 1 and 2 on the page 2. - All clamps and connectors are secure and tight. - There are no leaks. 2. Perform DTC confirmation procedure to confirm the incident. - Refer to the Electronic Service Manual (ESM) for DTC confirmation procedures. See this bulletin for further detail.

specific 2016 Titan XD vehicles.

adjustment procedure must be performed using C-III plus. IMPORTANT: If the transmission adjustment is not performed, the transmission may have the following conditions: Poor shift quality, Improper shift timing, Engine RPM flares between shifts See this bulletin for further detail.

The software is being updated to refine the MIL illumination logic.

UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicles 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.

CONTROL SLOW RESPONSE) IS stored, And DTC P00AF (BOOST PRESSURE CONTROL) is NOT stored in the ECM, And Binding and/or resistance is observed when the rotary turbine control valve is moved from one stop to the other (full span), by hand. NOTE: Disconnect the linkage at the actuator to move the rotary control valve. ACTION Replace the low pressure turbocharger.

the high pressure turbocharger on the APPLIED VEHICLES, listed above, are now available as separate service parts. If the low pressure turbocharger on an APPLIED VEHICLE is being replaced for any reason, refer to NTB20-071 for the removal procedure, installation procedure and parts information. If the high pressure turbocharger on an APPLIED VEHICLE is being replaced for any reason, refer to NTB19-017 for the removal procedure, installation procedure and parts information.

Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2016-2017 Titan XD vehicles equipped with a diesel engine. The Engine Control Module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC731 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealers inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties and/or fines by the Environmental Protection Agency. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

IF YOU CONFIRM A whistle noise is heard when refueling the vehicle. ACTION Replace the fuel tank with the new one listed in the PARTS INFORMATION section of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

canister vent control valve close) stored in the ECM and water is found in the EVAP filter, canister, or vent control valve ACTION Remove and replace the: - Fuel filler tube. - EVAP filter. - EVAP canister. - EVAP vent control valve. - EVAP pressure sensor. IMPORTANT: Before any parts are removed from the vehicle, note the EVAP filter orientation and hose routing (take a photo). Hose routing and EVAP filter orientation is critical and varies depending on production date.

with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

IF YOU CONFIRM The MIL is ON and DTC P2048 (REDUCTANT INJECTION VALVE CIRCUIT LOW 1/1) is stored. ACTION Reprogram the ECM per the SERVICE PROCEDURE in this bulletin. - Refer to SERVICE PROCEDURE on the next page to confirm if reprogramming is needed. - Save Computer Data with CONSULT-III plus (C-III plus). - If this bulletin applies, continue with ECM Reprogramming procedure. - Write Saved Data with CONSULT-III plus.

with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON with DTC P0299 (BOOST PRESSURE) stored And - The engine air cleaner box and air filter: - Are free from debris - Are not damaged or have any restrictions - The engine charge air cooler tube clamps are tight and tubes are free from leaks at the following locations: - The turbocharger compressor outlet - The charge air cooler inlet - The charge air cooler outlet - The intake manifold inlet - The Boost Pressure Absolute is within +/- 1.5 PSI of ambient air pressure with ignition ON and engine OFF (observed in Data Monitor). ACTION Refer to Repair Overview on page 2.

SERVICE INFORMATION When diagnosing any Diesel Exhaust Fluid (DEF) system component, refer to Table A below. These parts are now available separately. Do not replace the entire DEF tank assembly if the required part is shown in Table A.

SERVICE INFORMATION The Stage 1 and Stage 2 fuel filters must be replaced every 10,000 miles or a restriction may develop. DTCs P008A, P00C6, P0087 and/or a whining noise from the Stage 1 Fuel Filter Module may be present due to a restriction in the Stage 1 and/or Stage 2 fuel filters. NOTE: An inoperable or whining Stage 1 Fuel Filter Module that has not had the fuel filters regularly replaced as per the Owner?s Manual Maintenance schedule is not a warrantable repair. Before proceeding with any fuel system restriction diagnosis: - Confirm that both of the vehicle?s Stage 1 and Stage 2 fuel filters have been replaced at the correct service intervals, as per the Owner?s Manual Maintenance schedule. IMPORTANT: Warranty claim submissions for a Stage 1 Fuel Filter module will be denied if the Stage 1 and/or Stage 2 fuel filters have not been replaced per the Owner's Manual maintenance schedule.

vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION For the Applied Vehicles, the high pressure fuel injector supply line nut torque specifiction listed in the Electronic Service Manual (ESM) has been revised. Until the ESMs are updated, use the torque specification shown below.

Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. Changes were made on page 4, 6, and 12. Please discard previous versions of this bulletin.

applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. The Applied Vehicles section, Table A on page 7, and the DTC Confirmation procedure have been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.

to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended to change the Classification number. No other changes have been made. Please discard previous versions of this bulletin.

to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100F (37.8C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100F (37.8C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100F (37.8C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

No other changes were made. Please discard previous versions of this bulletin.

Stage 2 fuel filters, it is important not to damage the new fuel filters, inner seals, or O-rings. Refer to the Service Procedure section of this bulletin or the Electronic Service Manual (ESM) ENGINE> FUEL SYSTEM> CUMMINS 5.0L> REMOVAL AND INSTALLATION to ensure the filters are being replaced correctly. P008A LOW FUEL PRESSURE CONTROL SYSTEM and/or a no start condition may occur if the procedure is not followed properly.

vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM An applied vehicle?s idle fluctuates after starting when: - The coolant temperature is between 68F (20C) and 104F (40C) and - The vehicle is not moving (0 MPH). NOTE: This incident may continue until the coolant temperature reaches 104F (40C). ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.

equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The customer reported the following: While driving in conditions where wheel slip can occur (such as dirt, sand, mud, snow/ice, etc.), or while driving/sitting in traffic at slow speeds or idle: -The red A/T Oil Temp lamp began flashing, And/or -Vehicle would not move (the engine felt like it had no power), And -Vehicle operation returned to normal when the engine/transmission was allowed to cool. ACTION 1. Compare the vehicle?s current TCM part number to the part number listed in Table A on page 7. 2. If the current TCM part number matches a part number listed in Table A, follow the instructions in Table A.

equipped with a Cummins Diesel engine. This bulletin has been amended to update Applied Vehicles, remove the installation of a micro filter and to add a reprogramming procedure. No other changes have been made. Please discard previous versions of this bulletin.

applies to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. The Title and all sections on page 1 have been updated. Table A has also been updated. Please discard previous versions of this bulletin.

TEMPERATURE SETTING This bulletin applies to vehicles with dual climate control air conditioning. IF YOU CONFIRM With the HVAC system of an applied vehicle set in dual climate control mode and both driver and passenger sides are set at the same temperature: A. Temperature set for cool air: The outlet temperature of the driver side vents are warmer by 10F or more than the passenger side vent temperatures OR B. Temperature set for warm air: The outlet temperature of the passenger side vents are cooler by 10F or more than the driver side vent temperatures. ACTION 1. If A above is occurring: Replace only the driver side air mix door motor (see Parts Information). - Refer to the Electronic Service Manual (ESM), section HAC-Heater & Air Conditioning Control System, for driver air mix door motor removal and installation. 2. If B above is occurring: Replace only the passenger side air mix door motor (see Parts Information). - Refer to the Electronic Service Manual (ESM), section HAC-Heater & Air Conditioning Control System, for passenger air mix door motor removal and installation.

quality action to reprogram and, if necessary calibrate, the Transmission Control Module (TCM) on specific MY2016-17 Titan XD (A61) vehicles identified in SERVICE COMM and National Service History ? Open Campaigns. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. The software update will prevent one or more of the following concerns: - Transmission shift shock when accelerating enough to create a 7 3 downshift - Engine RPM fluctuation while driving at a steady speed - Lack of power under light acceleration at low speeds (may be described as hesitation; feeling like the transmission is in too high of a gear) ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by using Service Comm or National Service History ? Open Campaign I.D. PC604. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to reprogram the TCM and, if applicable, the ECM. - If reprogramming issues arise, use CONSULT III Software version 73.10 - Use the following claims information for vehicles identified in Service Comm or DBS National Service History ? Open Campaigns ID PC604 3. Dealers are requested to remedy any affected vehicle in dealer new inventory to ensure customer satisfaction. Thank you for your prompt attention to this matter. NISSAN NORTH AMERICA, INC. Aftersales DIVISION

IF YOU CONFIRM The coolant heater (block heater) needs to be replaced based on the Electronic Service Manual (ESM) inspection, and The vehicle is currently equipped with a coolant heater (with attached cord) located in the front engine cover. NOTE: - This bulletin does not apply if the vehicle is equipped with a coolant heater located in the water inlet at the lower radiator hose. - Refer to the ESM, section CO ? Engine Cooling System, for coolant heater operation and inspection information. ACTION 1. Use the Service Procedure in this bulletin to install a new coolant heater, locating it in the water inlet at the lower radiator hose. 2. Cut the cord to the original coolant heater.

This bulletin has been amended to add Armada to the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been changed throughout. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.

Cummins (5.0L V8) Diesel engine only. This bulletin has been amended. Substantial changes have been made throughout the body of the bulletin. Please discard all previous versions of this bulletin.

IF YOU CONFIRM While driving, the ?Key System Error? warning displays, and When parking the vehicle and pushing the Start/Stop switch, the ignition/engine does not turn OFF, and The connector cap for the hood switch harness connector (connector E94) is missing or damaged. NOTE: Refer to Figures A and B on the next page for examples of missing and damaged connector cap. ACTION Replace the hood switch harness connector (connector E94) with the new one (Service Kit) listed in the Parts Information.

VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.

ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS

the engine RPM goes up and down (fluctuates) a small amount. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm TCM reprogramming applies. 2. If it applies, reprogram the TCM.

and make changes to the body of the bulletin. Please discard previous versions.

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

vehicles with a V8 gasoline engine. This bulletin has been amended throughout. Discard all previous versions of this bulletin.

Coupe, Altima Sedan, Pathfinder and Murano vehicles with a 6-cylinder engine and Titan/Titan XD vehicles with a V8 gasoline engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

IF YOU CONFIRM The MIL is ?ON? with DTC U3017 (CAN Communication), and There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus. 5. Perform DTC Confirmation Procedure and Clear DTC.

IF YOU CONFIRM The MIL is ON with one or both of the following DTCs stored: - P0604 (ECM [Internal Control Module Random Access Memory (RAM) Error]) - P2299 (ACCEL PEDAL POS BRAKE SWITCH) And There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure (page 7), confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

been amended to include instructions for repair if DTC P0524 is stored and, if the HP turbo fails inspection. Please discard previous versions of this bulletin.

vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. IF YOU CONFIRM section was updated. No other changes were made. Please discard all previous versions of this bulletin.

with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. A DTC has been removed from the IF YOU CONFIRM section. No other changes have been made. Please discard previous versions of this bulletin.

only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON with DTC P218F (REDUCTANT NO FLOW DETECTED) stored When The vehicle is operated in ambient temperatures at 32F (0C) or below And There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure (page 7), confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

IF YOU CONFIRM Re-acceleration delay as follows: - Driving at a moderate steady speed, then - Reduce accelerator position to slow down, then - Increase accelerator position to bring the vehicle back to the previous speed, then - There is a delay/hesitation before the vehicle begins to accelerate. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

IF YOU CONFIRM The MIL is ON with P207F (Reductant Quality Performance) stored. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus. 5. Perform DTC confirmation.

IF YOU CONFIRM Any of the following issues: - When cold (transmission fluid below 140F [60C]), there is an engine RPM rise (200 to 500 RPM flare) during the 1-2 shift, 2-3 shift, and/or the 3-4 shift. - While slowing to a stop, a 2-1 down shift bump is felt just before stopping. - Harsh up-shifts. - Shift shock when lifting your foot from the accelerator. - Gear hunting while driving in city traffic. ACTION 1. Compare the vehicle?s current TCM part number to the part number listed in Table A on page 7. - If the current TCM part number matches a part number listed in Table A, follow the instructions in Table A. 2. Save computer data with CONSULT-III plus (C-III plus). 3. Compare the vehicle?s current ECM part number to the part number listed in Table B on page 30. - If the current ECM part number matches a part number listed in Table B, reprogram the ECM. - Write saved data. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

For Titan and Titan XD, this bulletin applies only vehicles equipped with gasoline engines. This bulletin has been amended in the PARTS INFORMATION and CLAIMS INFORMATION sections. Discard previous versions of this bulletin.

equipped with Cummins 5.0L Diesel engine. SERVICE INFORMATION Some customers may want to use a coolant heater (engine block heater) for their vehicle when ambient temperatures are below 32F (0C). 2016 Titan XD: - Some were not equipped from the factory with a coolant heater or cord. - Some were equipped with coolant heater, but not a cord. 2017 Titan XD: Was equipped from the factory with a coolant heater, but some were not equipped with the coolant heater cord. If a customer chooses to purchase the parts and labor for installation of a coolant heater and/or coolant heater cord, use the Service Procedure in this bulletin for installation instructions.

December 15th, 2016 has been revised to include: - High pressure turbo kits and additional service parts for diesel engine repair are no longer on restriction and may be ordered via normal process. Orders placed prior to restriction removal will be fulfilled. Please discard earlier versions of this bulletin.

The CLAIMS INFORMATION section has been corrected. No other changes have been made. Please discard previous versions of this bulletin.

Coupe, Altima, Pathfinder and Murano vehicles equipped with V6 engine OR Titan/Titan XD equipped with VK56 engine IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve, And The valve timing control solenoid valve operates correctly and is not externally damaged. ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.

the engine block heater (if equipped) on an Applied Vehicle (engine block heater is plugged in): - Vehicle should be parked on a level surfaces. Or - If a level surface is not available, the vehicle should be parked with the front of the truck lower than the rear (nose down). CAUTION: Use of the engine block heater when parked with the front of the vehicle higher than the rear (5 degrees or more) may cause the engine block heater to become damaged and/or inoperative.

revised to include: o Campaign Bulletin NTB16-097 is now available on NNAnet, ASIST & Dealer360. o Service Comm now active for retailed VINs. o Dealers may order parts for affected retailed units via DCS beginning October 13, 2016. - Please discard earlier versions of this bulletin.

is conducting a Voluntary Emissions Service Campaign on certain specific Model Year 2016 Nissan Titan XD vehicles with Cummins 5.0L to inspect and replace the high pressure turbocharger assembly. This service will be performed at no charge to owners for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC471 to this campaign. The correct number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to correct each vehicle falling within the range of this campaign that enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory.

(Turbocharger Boost Control Slow Response) - P0471 (Exhaust Pressure Sensor "A" Circuit Range/Performance) and There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

YOU CONFIRM section, add information to step 6B and Table A. No other changes were made. Please discard previous versions of this bulletin.

revised to include: o Campaign Bulletin NTB16-097 has been amended to include instructions for repair if the High Pressure turbo fails inspection and DTC P0524 (Engine Oil Pressure) is stored. - Please discard earlier versions of this bulletin.

THE SERVICE PROCEDURE HAS BEEN REVISED, AND APPLIED VIN AND DATE INFORMATION HAS BEEN ADDED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS."

AS PER OUR AUGUST 5TH ANNOUNCEMENT, NISSAN IS CONDUCTING A VOLUNTARY EMISSIONS SERVICE CAMPAIGN ON APPROXIMATELY 683 SPECIFIC MY 2016 TITAN XD DIESEL (A61) VEHICLES CURRENTLY IN DEALER INVENTORY TO ADDRESS AN EXCESSIVE OIL CONSUMPTION CONCERN WITH THE HIGH PRESSURE TURBOCHARGER. NISSAN HAS AUTOMATICALLY SHIPPED PARTS TO REPAIR AFFECTED VEHICLES CURRENTLY IN DEALER NEW VEHICLE INVENTORY AND SUBJECT TO THE QUALITY HOLD. DEALERS SHOULD FOLLOW THE REPAIR INSTRUCTIONS INCLUDED WITH THIS ANNOUNCEMENT TO REPAIR AFFECTED VEHICLES IN NEW VEHICLE INVENTORY. NISSAN IS STILL DEVELOPING A REPAIR PROCEDURE FOR AFFECTED RETAILED VEHICLES AT THIS TIME. NISSAN HAS NOT YET IDENTIFIED THESE VEHICLES IN SERVICE COMM. NISSAN EXPECTS TO BE ABLE TO MAKE AN ANNOUNCEMENT REGARDING RETAILED VEHICLES BY MID-TO-LATE SEPTEMBER. NOTE: ONLY CERTAIN TITAN XD DIESEL VEHICLES ARE AFFECTED, WHILE OTHER TITAN XD DIESEL VEHICLES ARE NOT, SO DEALERS NEED TO FOLLOW INSTRUCTIONS BELOW TO IDENTIFY THE AFFECTED VEHICLES. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY EMISSIONS SERVICE CAMPAIGN USING SERVICE COMM I.D. PC471. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE ATTACHED REPAIR PROCEDURE. NOTE: IF DTC P0524 IS FOUND STORED, DEALERS WILL NEED TO SEND THE REQUESTED DETAILS TO NNAFQASUPPORT@NISSAN-USA.COM AND AWAIT FURTHER INSTRUCTION. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE. 5. DEALERS ARE REMINDED TO FOLLOW ALL LOCAL LAWS AND REGULATIONS REGARDING DISCLOSURES OF REPAIRS TO NEW VEHICLES PRIOR TO SALE."

IF YOU CONFIRM A BUMP OR SHOCK IS FELT FROM THE DRIVETRAIN, - ONLY WHILE TRAVELING AT 40 MPH OR MORE, AND THEN - LIGHTLY APPLYING THE ACCELERATOR AFTER BRIEFLY COASTING. ACTION 1. REFER TO STEP 6 IN THE SERVICE PROCEDURE TO CONFIRM THIS BULLETIN APPLIES TO THE VEHICLE YOU ARE WORKING ON. 2. IF THIS BULLETIN APPLIES, REPROGRAM THE ECM."

EMISSION SERVICE CAMPAIGN ON APPROXIMATELY 1,044 MODEL YEAR 2016 NISSAN TITAN XD (GASOLINE ONLY) VEHICLES. NISSAN HAS DISCOVERED THAT MODEL YEAR 2016 WARRANTY INFORMATION BOOKLET CONTAINS INACCURATE INFORMATION RELATED TO THE FEDERAL EMISSION PERFORMANCE AND DEFECT WARRANTY COVERAGE DETAILS. THE VEHICLES EMISSION PERFORMANCE AND DEFECT WARRANTIES WERE INCORRECTLY LISTED AND SHOULD HAVE BEEN LISTED AS 5 YEARS / 50,000 MILES. THE VEHICLES FEDERAL AND CALIFORNIA EMISSION LONG TERM DEFECT WARRANTIES REMAIN UNCHANGED. VEHICLE SAFETY, FUEL ECONOMY, DRIVABILITY AND PERFORMANCE ARE NOT AFFECTED. TO CORRECT THIS CONDITION, NISSAN IS CONDUCTING A VOLUNTARY EMISSION SERVICE CAMPAIGN TO PROVIDE A WARRANTY ADDENDUM STICKER THAT CONTAINS THE MOST CURRENT EMISSION WARRANTY INFORMATION TO OWNERS AND DEALERS WITH AFFECTED INVENTORY."

CHANGES HAVE BEEN MADE TO ITEMS 1, 4, AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON, UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM."

BELOW 140F [60C]), THERE IS AN ENGINE RPM RISE (200 TO 500 RPM FLARE) DURING THE 1-2 SHIFT, 2-3 SHIFT, AND/OR THE 3-4 SHIFT. AND/OR -WHILE SLOWING TO A STOP, A 2-1 DOWN SHIFT BUMP IS FELT JUST BEFORE STOPPING. ACTION 1. COMPARE THE VEHICLES CURRENT TCM PART NUMBER TO THE PART NUMBER LISTED IN TABLE A ON PAGE 4. 2. IF THE CURRENT TCM PART NUMBER MATCHES A PART NUMBER LISTED IN TABLE A: A. REPROGRAM THE TCM. B. PERFORM TRANSMISSION CALIBRATION."

SPECIFIC 2016 TITAN XD VEHICLES IDENTIFIED IN SERVICE COMM. ON THE AFFECTED VEHICLES, THE SOFTWARE IS BEING UPDATED TO REFINE THE MIL ILLUMINATION LOGIC. THESE VEHICLES ARE EITHER CURRENTLY IN DEALER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE DEALER."

Control Module (ECM) software on 3,334 specific 2016 Titan XD vehicles identified in Service Comm. On the affected vehicles, the software is being updated to refine the MIL illumination logic. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer.

transmission DTCs are stored: P0729: 6GR Incorrect Ratio P0730: Incorrect Gear Ratio P0731: 1GR Incorrect Ratio P0732: 2GR Incorrect Ratio P0733: 3GR Incorrect Ratio P0734: 4GR Incorrect Ratio P0735: 5GR Incorrect Ratio P1734: 7GR Incorrect Ratio 1. Check all of the engine intake air ducting and make sure: It is connected securely and correctly at the throttle body and all other connections. See Figures 1 and 2 on the next page. All clamps and connectors are secure and tight. There are no leaks. 2. Perform DTC confirmation procedure to confirm the incident. Refer to the Electronic Service Manual (ESM) for DTC confirmation procedures.

Transmission Control Module (TCM) is replaced an adjustment procedure must be performed using CONSULT-III plus. IMPORTANT: If the transmission adjustment is not performed, the transmission may have the following conditions: Poor shift quality Improper shift timing Engine RPM flares between shifts SERVICE PROCEDURE 1. Make sure the transmission is warm. It may be helpful to take the vehicle for a drive (approximately 10 minutes) to warm the transmission. 2. Confirm the transmission fluid level is correct. Follow the procedure for Checking the AT Fluid Level in the Electronic Service Manual (ESM), section TM-Transaxle & Transmission. 3. Set the parking brake. 4. Chock the wheels. 5.Connect the CONSULT PC to the vehicle with the plus VI. 6. Start the engine. 7. Turn the A/C system OFF. 8. Start CONSULT-III plus (C-III plus). 9. When the VI is recognized, select Diagnosis (One System).

P020A - F: Cylinder 1 6 Injection Timing P021A - B: Cylinder 7 8 Injection Timing P060C: Internal Control Module Main Processor Performance P2048: Reductant Injector Circuit Low P207F: Reductant Quality Performance P2263: Turbocharger Boost System Performance ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

h P020A - F: Cylinder 1 V 6 Injection Timing h P021A - B: Cylinder 7 V 8 Injection Timing h P060C: Internal Control Module Main Processor Performance h P2048: Reductant Injector Circuit Low h P207F: Reductant Quality Performance h P2263: Turbocharger Boost System Performance ACTION 1. Save Computer Date with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Date with CONSULT-III plus.

ambient temperature is around or below 0C (32F) the following recommendations must be followed. NOTE: These recommendations are also found in the vehicle Owners Manual.  Always use the correct engine oil for the prevailing conditions Use of an engine block heater (if so equipped) when the ambient temperature is around -17.77C (0F) or lower. Engine block heaters are used to assist with cold temperature starting. Some heaters will operate continuously when plugged into the correct voltage electrical socket. Operate them only when the ambient temperature is below - 17.77C (0F).  Always use the correct type of diesel fuel. When two types of diesel fuel are available, use winter fuel when the ambient temperature is around or below 0C (32F).  Importance of maintaining battery state-of-charge. If the battery is not fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maximum efficiency, the battery should be checked regularly. For additional information, refer to Battery in the Do-it-yourself section of the applicable vehicle Owners Manual. Care should be taken to avoid situations that can lead to potential battery discharge and potential no-start conditions such as: 1. Installation or extended use of electronic accessories that consume battery power when the engine is not running (Phone changers, GPS, DVD players, etc.).these cases, the battery may need to be charged to maintain battery health. 2. Infrequent operation of the vehicle or regularly driving only short distances in the vehicle. In these cases, the battery may need to be charged to maintain battery health.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

been delivered without certain accessories. Nissan is delivering parts to those affected dealers to install the missing accessories on the vehicle.

been delivered without certain accessories. Nissan is delivering parts to those affected dealers to install the missing accessories on the vehicle.

been delivered without certain accessories. Nissan is delivering parts to those affected dealers to install the missing accessories on the vehicle.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

The Applied Vehicles section has been revised. No other changed have been made. Please discard previous versions of this bulletin.

Please discard all previous versions of this bulletin.

during moderate to hard acceleration at speeds less than 25 mph. And - Does not occur at speeds above 25 mph. - May be worse when towing a trailer. ACTION Refer to the Repair Overview on page 2 for model specific Actions.

PARTS, AND CLAIMS INFORMATION FOR THE PREVIOUSLY ANNOUNCED QUALITY HOLD"

ACTION NECESSARY FOR THE PREVIOUSLY ANNOUNCED QUALITY HOLD"

vehicles in their inventory that may have been delivered without certain accessories. Nissan is delivering parts to those affected dealers to install the missing accessories on the vehicle. Nissan has instructed dealers to not trade the vehicles because the parts are being delivered to the original wholesale dealer of record. Nissan also requested dealers to install the parts shipped to them for affected vehicles before they are sold to ensure the vehicle has all the equipment listed on the Monroney label and to ensure customer satisfaction.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Ts 3G network connection, including Nissan Group, have had connectivity services affected. NissanConnect Services are no longer available on the APPLIED VEHICLES listed above.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

communicated instructions to dealers regarding specific vehicles in their inventory that may have been delivered without certain accessories. Nissan is delivering parts to those affected dealers to install the missing accessories on the vehicle. Nissan has instructed dealers to not trade the vehicles because the parts are being delivered to the original wholesale dealer of record. Nissan also requested dealers to install the parts shipped to them for affected vehicles before they are sold to ensure the vehicle has all the equipment listed on the Moinroney label and to ensure customer satisfaction. If the dealer elects to deliver an affected vehicle without this equipment installed, the dealer should inform the customer of the missing accessfory part(S) prior to sale. The dealer should also have the customer acknowledge in writing his/her understanding that the sfpecific accessory is included in the price of the vehiclew, but is not currently installed on the vefhicle, and the dealer will contact the customer to schedule an appointment for part installation upon the dealer's receipt of the part.

inventory that should be equipped with storage boxes, but were shipped without the storage boxes installed. 247 specific MY 2016 Titan XD vehicles idenfified in Service Comm will require storage box installation. These vehicles are currently in dealer inventory, assigned and in transit to the dealer, or retailed.

vehicles that should be equipped with this accessory, but were shipped without the splash guards installed.

that should be equipped with this accessory, but were shipped without the step rails installed.

bedliner and a cargo tie down kit that should have been installed on the vehicle from the factory, but were not.

assembly on 2,602 specific 2016 Titan XD vehicles.

warning, and - Both headlamps are visually working correctly, - It may be difficult to determine the exact cause. - Use the information in this bulletin as an aid, along with the Electronic Service Manual (ESM), to isolate the root cause and fix it right the first time.

warning, and - Both headlamps are visually working correctly, - It may be difficult to determine the exact cause. - Use the information in this bulletin as an aid, along with the Electronic Service Manual (ESM), to isolate the root cause and fix it right the first time.

warning, and - Both headlamps are visually working correctly, - It may be difficult to determine the exact cause. - Use the information in this bulletin as an aid, along with the Electronic Service Manual (ESM), to isolate the root cause and fix it right the first time.

No other changes have been made. Please discard previous versions of this bulletin.

device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.

LED headlamp adjustment information has been corrected. Please discard previous versions of this bulletin.

ELECTRONIC SERVICE MANUAL (ESM). - WARRANTY CLAIMS FOR HEADLAMP ADJUSTMENT ARE SUBJECT TO AUDIT. - CLAIMS MUST HAVE THE MEASUREMENTS FOR DIMENSION A, B, AND C (SHOWN IN THIS BULLETIN) LISTED ON THE REPAIR ORDER AND ON THE TECHNICIAN COMMENTS LINE OF THE CLAIM. - CLAIMS SUBMITTED WITHOUT THESE MEASUREMENTS MAY BE DENIED."

CAMPAIGN ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL SPLASH GUARDS ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE SPLASH GUARDS INSTALLED. ***** WHAT DEALERS SHOULD DO***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC434. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. DEALERS SHOULD USE NTB16-080 TO CORRECT ANY VEHICLES SUBJECT TO THIS CAMPAIGN. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT A WARRANTY CLAIM AND RELEASE THE VEHICLE."

CAMPAIGN ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL STEP RAILS ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE STEP RAILS INSTALLED. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC428. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE REPAIR PROCEDURE IN NTB16-081. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE."

ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL STORAGE BOXES ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE STORAGE BOXES INSTALLED. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC423. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE REPAIR PROCEDURE IN NTB16-078. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE."

CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL RUNNING BOARDS THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WERE NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC428 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY."

CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL SPLASH GUARDS THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WERE NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC434 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY."

CONDUCTING THIS VOLUNTARY SERVICE CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL A DUAL WALL BEDLINER AND A CARGO TIE DOWN KIT THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WERE NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC423 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY."

***** DETAILED INFORMATION ***** NISSAN IS COMMITTED TO A HIGH LEVEL OF CUSTOMER SERVICE AND SATISFACTION. THIS COMMITMENT REQUIRES NISSAN TO PERIODICALLY PLACE CERTAIN SPECIFIC VEHICLES ON A TEMPORARY QUALITY ASSURANCE (QA) HOLD TO ASSURE THAT THESE VEHICLES, AS DELIVERED TO OUR CUSTOMERS, MEET OUR EXACTING STANDARDS AND OUR CUSTOMERS EXPECTATIONS. EFFECTIVE IMMEDIATELY, NISSAN IS PLACING A TEMPORARY QUALITY ASSURANCE (QA) HOLD ON APPROXIMATELY 734 SPECIFIC MY 2016 TITAN XD (A61) VEHICLES. NOTE: ONLY CERTAIN TITAN SD VEHICLES ARE AFFECTED, AND OTHER TITAN XD VEHICLES ARE NOT AFFECTED BY THE QA HOLD, SO DEALERS NEED TO FOLLOW INSTRUCTIONS BELOW TO IDENTIFY THE AFFECTED VEHICLES. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES CURRENTLY IN DEALER INVENTORY ARE AFFECTED BY THIS QA HOLD USING SERVICE COMM I.D. PC471 NOTE: DEALERS SHOULD CONTINUE TO CHECK NEW ARRIVING INVENTORY FOR QA HOLD APPLICABILITY. 2. PLEASE DO NOT DRIVE, SELL, OR TRADE THE SPECIFIC 2016 TITAN XD VEHICLES IN DEALER INVENTORY SUBJECT TO THIS QA HOLD. 3. NO FURTHER ACTION IS NECESSARY AT THIS TIME. NISSAN WILL PROVIDE AN UPDATE BY AUGUST 5TH, 2016."

***** DETAILED INFORMATION ***** NISSAN IS COMMITTED TO A HIGH LEVEL OF CUSTOMER SERVICE AND SATISFACTION. THIS COMMITMENT REQUIRES NISSAN TO PERIODICALLY PLACE CERTAIN SPECIFIC VEHICLES ON A TEMPORARY QUALITY ASSURANCE (QA) HOLD TO ASSURE THAT THESE VEHICLES, AS DELIVERED TO OUR CUSTOMERS, MEET OUR EXACTING STANDARDS AND OUR CUSTOMERS EXPECTATIONS. EFFECTIVE IMMEDIATELY, NISSAN IS PLACING A TEMPORARY QUALITY ASSURANCE (QA) HOLD ON APPROXIMATELY 23 MY 2016 TITAN (A61 AND A61D) VEHICLES. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES CURRENTLY IN DEALER INVENTORY ARE AFFECTED BY THIS QA HOLD USING SERVICE COMM I.D. PC469 NOTE: DEALERS SHOULD CONTINUE TO CHECK NEW ARRIVING INVENTORY FOR QA HOLD APPLICABILITY. 2. PLEASE DO NOT DRIVE, SELL, OR TRADE ANY OF THE 2016 TITAN VEHICLES IN DEALER INVENTORY SUBJECT TO THIS QA HOLD. 3. NO FURTHER ACTION IS NECESSARY AT THIS TIME. NISSAN WILL PROVIDE AN UPDATE BY JULY 29TH, 2016."

ON ACTION NECESSARY FOR THE PREVIOUSLY ANNOUNCED QUALITY HOLD ***** DETAILED INFORMATION ***** AS PER OUR PREVIOUS ANNOUNCEMENT, NISSAN PLACED A TEMPORARY QUALITY ASSURANCE (QA) HOLD ON APPROXIMATELY 23 MY 2016 TITAN VEHICLES ON JULY 14, 2016 TO ENSURE VEHICLES DELIVERED TO OUR CUSTOMERS MEET OUR EXACTING STANDARDS AND CUSTOMER EXPECTATIONS. THIS TEMPORARY HOLD REMAINS IN EFFECT. NISSAN HAS CONCLUDED THE AFFECTED VEHICLES WILL REQUIRE THE FRONT CENTER SEAT ASSEMBLY TO BE REPLACED AS THE CENTER SEAT RISER DOES NOT MEET NISSAN DESIGN STANDARDS. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES CURRENTLY IN DEALER INVENTORY ARE AFFECTED BY THIS QA HOLD USING SERVICE COMM I.D. PC469 NOTE: DEALERS SHOULD CONTINUE TO CHECK NEW ARRIVING INVENTORY FOR QA HOLD APPLICABILITY. 2. PLEASE DO NOT SELL OR TRADE ANY AFFECTED VEHICLES IN DEALER INVENTORY. 3. NO FURTHER ACTION IS NECESSARY AT THIS TIME. NISSAN WILL COMMUNICATE INSTRUCTIONS AND CLAIMS INFORMATION WHEN PARTS SHIPMENTS BEGIN TO AFFECTED DEALERS."

INVENTORY INSPECTION ON 963 SPECIFIC 2016 TITAN VEHICLES IDENTIFIED IN SERVICE COMM. DEALERS SHOULD INSPECT THE FRONT PROP SHAFT BOLT TORQUE AND IF THE BOLTS ARE FOUND TO BE NOT TORQUED TO SPECIFICATION, ALL BOLTS AND NUTS SHOULD BE REPLACED AND TIGHTENED TO SPECIFICATION THESE VEHICLES ARE EITHER CURRENTLY IN DEALER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE DEALER. *****WHAT DEALERS SHOULD DO***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. VERIFY IF VEHICLES CURRENTLY IN DEALER INVENTORY ARE AFFECTED BY THIS INSPECTION USING SERVICE COMM I.D. PC474. -AS A REMINDER NEW VEHICLES IN DEALER INVENTORY CAN BE ALSO BE IDENTIFIED USING DCS (SALES-> VEHICLE INVENTORY, AND FILTER BY OPEN CAMPAIGN) OR SERVICE COMM. 2. USE THE ATTACHED PROCEDURE TO INSPECT THE FRONT PROP SHAFT BOLT TORQUE AND IF NECESSARY, REPLACE THE PROP SHAFT NUTS AND BOLTS AND TIGHTEN THE FASTENERS TO SPECIFICATION. 3. THE SERVICE DEPARTMENT SHOULD SUBMIT THE APPLICABLE WARRANTY CLAIM FOR THE ACTION PERFORMED SO IT CAN BE CLOSED ON SERVICE COMM AND RELEASE THE VEHICLE. ***** DEALER RESPONSIBILITY ***** IT IS THE DEALERS RESPONSIBILITY TO CHECK SERVICE COMM USING THE APPROPRIATE CAMPAIGN I.D FOR THE INSPECTION STATUS ON EACH AFFECTED VEHICLE CURRENTLY IN INVENTORY. NISSAN REQUESTS DEALERS TO PERFORM THIS INSPECTION ON VEHICLES IN INVENTORY PRIOR TO BEING RETAILED TO ENSURE CUSTOMER SATISFACTION."

were shipped without the storage boxes installed. 247 specific MY2016 Titan XD vehicles identified in SERVICE COMM will require storage box installation. These vehicles are currently in dealer inventory, assigned and in transit to the dealer, or retailed.

Nissan is conducting a Voluntary Emissions Recall Campaign on certain 2016-2019 Titan Diesel vehicles identified in Service Comm and DBS National Service History. Vehicles affected by this campaign require upgraded emissions control software and hardware for model years 2016-2017 or upgraded software only for model years 2018-2019. This finding has no effect on the safety of the vehicle. Cummins and the California Air Resources Board have entered into an agreement to correct this condition. In order to implement this correction, Nissan is conducting a Voluntary Emission Recall Campaign. The remedy and parts are now available. Nissan dealers will update the emissions control software and install a Particulate Matter Sensor for model years 2016-2017 and update emissions control software only for model years 2018-2019. IMPORTANT: It is a violation of Federal law for dealers to sell or deliver new vehicles in their inventory covered by this notification until the campaigns remedy action is performed.): REVISION 2 Please discard earlier versions of this bulletin. The announcement from January 10, 2025 has been revised to include the following: The remedy and parts are now available, please refer to NTB24-061 to remedy any vehicle affected by PD128 and NTB24-062 to remedy any vehicle affected by PD129. Parts are on restriction and can be ordered via DBS. Affected Models/Years: Affected Population: Dealer Inventory: SERVICE COMM Activation date: Stop Sale In Effect 2016-2017 Titan (A61D) 27,085 NA December 20, 2024 NO Affected Models/Years: Affected Population: Dealer Inventory: SERVICE COMM Activation date: Stop Sale In Effect 2018-2019 Titan (A61D) 11,614 ***** Campaign Summary ***** Nissan is conducting a Voluntary Emissions Recall Campaign on certain 2016-2019 Titan Diesel vehicles identified in Service Comm and DBS National Service History. Vehicles affected by this campaign require upgraded emissions control software and hardware for model years 2016-2017 or upgraded software only for model years 2018-2019. This finding has no effect on the safety of the vehicle. Cummins and the California Air Resources Board have entered into an agreement to correct this condition. In order to implement this correction, Nissan is conducting a Voluntary Emission Recall Campaign. The remedy and parts are now available. Nissan dealers will update the emissions control software and install a Particulate Matter Sensor for model years 2016-2017 and update emissions control software only for model years 2018-2019.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly (fuel pump assembly). The fuel level sensor can be replaced separately. P0460 (FUEL LEV SEN SLOSH) P0461 (FUEL LEVEL SENSOR) P0462 (FUEL LEVL SEN/CIRC) P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

With an active NissanConnectSM Services subscription, the TCU communicates with the NissanConnectSM Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. See this bulletin for further detail.

ACTION 1. Replace the Outlet NOx Sensor. 2. Confirm that ECM requires reprogramming. Refer to step 6 on page 7. If the ECM requires reprograming: a. Perform Save Computer Data with CONSULT-III plus (C-III plus). b. Reprogram ECM. c. Perform Write Saved Data. See this bulletin for further detail.

sonar activates with no obstacle ahead), inspect the front license plate, front license plate frame and if equipped, the front license plate bracket. See page 2 for example photos. The front sonar parking sensor may activate if the front license plate is bent outward from its bracket (there is a gap between the license plate and the bracket) OR the front license plate frame is bent or loose and is hanging outward, away from the license plate and/or bracket (there is a gap between the license plate frame and the license plate and/or bracket) OR the bracket is loose and is hanging outward, away from the bumper (there is a gap between the bracket and the bumper). If any of these conditions are found, correct it by removing the gap (straighten the license plate, straighten and/or secure the license plate frame, or secure the bracket, as it applies). - Retest the operation of the front sonar parking sensor. If the issue is not resolved, go to ASIST and the related Electronic Service Manual (ESM) for further diagnosis. See this bulletin for further detail.

Turn the ignition OFF. 2. Wait at least 2 minutes. 3. Disconnect battery (negative cable first). NOTE: - If the above steps are not followed, DTCs P2509 and P181B may be stored. - If these codes are stored because the battery disconnection was done without waiting 2 minutes, they can be cleared, but it is not a warrantable repair. See this bulletin for more detail.

This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

rear parking aid sensors are inoperative or operating incorrectly, And Damage has occurred to the rear sonar sensors or harness by road debris from the rear wheels. ACTION Install the rear sonar sensor protector kit, listed in the PARTS INFORMATION on page 7, to the rear bumper. NOTE: This bulletin does not cover any damage that has occurred to the rear sonar sensors or harness. Refer to the Electronic Service Manual (ESM) for component repair.

***** Nissan is conducting a Voluntary Emissions Recall Campaign on 27,085 certain MY2016-17 Titan Diesel vehicles identified in Service Comm to inspect and, if necessary, reprogram the Electronic Control Unit (ECU) with countermeasure software. Nissan has determined that the subject vehicles were manufactured with an On-Board Diagnostic (OBD) calibration that may not allow the exhaust gas sensor monitors to run as intended. If an affected vehicle is not repaired, the exhaust gas sensor monitors may not run as frequently as required by regulation to determine if the sensor is performing as intended. This issue has no effect on vehicle safety, fuel economy, drivability, or performance. ***** What Dealers Should Do**** 1. Verify campaign applicability using Service Comm or DBS National Service History Open Campaign I.D. PC731. 2. Dealers should use NTB20-030 to correct any vehicles subject to this campaign. 3. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on page 5. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

side climate controlled seat: - Heating and cooling features do not operate And - The harness connector or control unit of the climate controlled seat appears as shown in Figure 3 or Figure 5. ACTION Perform the following to the affected seat: A. Replace the climate controlled seat control unit. B. Drill a hole for the new harness clip. C. Replace the harness connector of the climate controlled seat control unit. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

See Amendment History on the last page. Please discard previous versions of this bulletin.

vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.

light is ON AND/OR The Vehicle Information Display states "Exhaust Filter Overloaded See Owner's Manual For Drive Pattern" AND DTC P1451 (Diesel Particulate Filter System Performance) is stored in the ECM NOTE: This DTC will not turn the MIL ON. AND The vehicle has less than 100 miles on the odometer. ACTION: 1. Perform a stationary regeneration. - Go to SERVICE PROCEDURE on page 2. 2. Erase the DTC.

OR ELECTRICALLY WITH THE KEY FOB. AND/OR - TAILGATE WILL NOT UNLATCH OR REQUIRES EXCESSIVE FORCE WHEN PULLING ON THE TAIL GATE HANDLE. ACTION SEE THE FLOW CHART ON PAGE 2 FOR THE APPROPRIATE REPAIR FOR THE VIN AND DATE OF THE VEHICLE BEING WORKED ON."

CHANGES HAVE BEEN MADE THROUGHOUT. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM THE INTELLIGENT KEY INTERMITTENTLY OR CONTINUOUSLY DOES NOT FUNCTION. ACTION CHECK THE BATTERY CONDITION WITH THE SIGNAL TECH-II I-KEY BATTERY TEST. IMPORTANT: CONFIRM THAT THE SIGNAL TECH-II HAS THE MOST RECENT UPDATE. UPDATE CAN BE PERFORMED THROUGH ASIST / SPECIALTY TOOLS / SIGNAL TECH-II."

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."

vibration is coming from the front or rear propeller shaft of an APPLIED VEHICLE, inspect the propeller shaft journals (U-Joints) for binding and/or abnormal noise before replacing the propeller shaft. If binding and/or abnormal noise is confirmed from the propeller shaft U-Joints, replace the propeller shaft U-Joints. Refer to the ESM for the propeller shaft U-Joint replacement procedure. NOTE: Replacement of the propeller shaft due to noise and/or vibration caused by the propeller shaft U-Joints may result in warranty charge back.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

LASER/RADAR in the PAST column: Erase the DTC. DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.

These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.

See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The new service part (B in Figure 1) is visually different, but is a direct replacement for the original equipment part. IMPORTANT: See page 2 for the procedure to inspect the cap bolt service part for excessive stretch. If replacement of a single connecting rod cap bolt is indicated for any given connecting rod, both connecting rod cap bolts of the affected connecting rod must be replaced as a set.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

vehicles, the replacement antenna base and antenna mast styles have changed to a new style, shown in Figure 1. The old style has been discontinued. If for any reason the old style antenna base needs to be replaced, both the base and the mast must be replaced as a set with the new style shown in Figure 1. If the vehicle still has the old style antenna base, as shown in Figure 2, and only the mast is damaged, a replacement antenna mast can be ordered.

This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.

This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.

The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.

THE PARTS INFORMATION SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."

PARTS INFORMATION SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. - PLEASE DISCARD EARLIER VERSIONS OF THIS BULLETIN."

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and bug fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

See AMENDMENT HISTORY on page 14. Please discard previous versions of this bulletin.

replacement Audio Unit's registration "code" . - Replace the Audio Unit as instructed in the Electronic Service Manual (ESM) and any applicable bulletins. - Register the replacement Audio Unit with Nissan Owner Services. NOTE: The Apps mode will not function if the Audio Unit serial number (registration code) is not registered. See this bulletin for further detail.

See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin

The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been superseded to NTB18-031. Please discard all previous versions of this bulletin.

vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

from the subwoofer mounting points under the passenger side seat. NOTE: If this incident should occur, - The customer may report the noise is coming from the passenger door. - The noise may be heard inside and outside the vehicle. ACTION Install the new subwoofer mounting screws and grommets listed in the PARTS INFORMATION section.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

not.

The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.

breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The APPLIED VEHICLES have been updated and the SERVICE PROCEDURE now includes the addition of foam to the outside handle bracket. Please discard previous versions of this bulletin.

Information for 2017 Altima, Murano, Pathfinder, Sentra, and Titan/Titan XD vehicles has been applied. No other changes have been made. Please discard previous versions of this bulletin.

on 1,004 specific 2016 Titan vehicles identified in Service Comm to replace components associated with the tailgate lock assembly. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to remedy the affected vehicles prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this service action using Service Comm I.D. PC470, PC549, and PC550. - New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information 2. Use the attached procedure to identify which components to replace:

THE APPLIED DATE INFORMATION IN THE REPAIR FLOW CHART ON PAGE 2 AND IN STEPS 6A AND 6B HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS."

SERVICE CAMPAIGN ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL ELECTRONIC TAILGATE LOCKS ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE ELECTRONIC TAILGATE LOCKS INSTALLED. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC466. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE REPAIR PROCEDURE IN NTB16-079. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE."

SERVICE CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL AN ELECTRONIC TAILGATE LOCK THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WAS NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC466 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY."

Voluntary Emissions Recall Campaign on specific model year 2016-2019 Titan Diesel vehicles identified in Service Comm and DBS National Service History. Vehicles affected by this campaign may have been shipped to market with an Exemption label and should have been shipped with a Vehicle Emission Control Information (VECI) label. Nissan dealers will inspect for the Exemption label and/or VECI label, and remove Exemption label if present and install VECI label if not present. ***** What Dealers Should Do**** 1. Verify if vehicles are affected by this Voluntary Emission Recall Campaign using Service Comm or DBS National Service History Campaign I.D. PD127. 2. Dealers should use NTB24-063 to remedy any vehicles affected by this campaign. 3. Once remedied, dealers should submit the claim, using the claims coding provided, and release the vehicle. ***** Release Schedule ***** Parts Refer to NTB24-063 to determine the parts required for this campaign. Part numbers 14805-EZ40B and 14805-9FU5A are on restriction and can be ordered via DBS. Part numbers 14805-EZ40A and 14805-EZ41C can be ordered via the normal process. Repair NTB24-063 Owner Notification Nissan will begin sending notifications to owners of all potentially affected vehicles in February 2025, via U.S. Mail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NOTE: Concern is more likely to: - Be heard from under the center of vehicle. - Occur more often on dry days. - Occur at regular intervals about every 30 seconds to 1 minute. ACTION Install the tether assembly as described in the SERVICE PROCEDURE starting on the next page.

We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

quality action to inspect the routing of the fuel tank breather tube on approximately 4,288 specific MY2016-17 Titan XD (A61D) vehicles. During vehicle assembly, certain plant operator technicians may not have removed the temporary fuel tank breather tube cap, and may not have correctly affixed the tube to the bed rail. No parts are required for this inspection. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History - Open Campaign I.D. PC594 - New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). i. Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to inspect the vehicle. - If the fuel tank breather tube is routed correctly, file a claim for the inspection. - If the fuel tank breather tube is not routed correctly, provide the requested information in an email to nnafqasupport@nissan-usa.com and await further instruction. Instructions and claims information will be provided within 48 hours. 3. Dealers are requested to inspect any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.

nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

Applied Vehicles, add step 11 to the Service Procedure and add a flowchart. No other changes have been made. Please discard previous versions of this bulletin.

Contamination of the Diesel Exhaust Fluid (DEF) system with fluids other than DEF can cause permanent damage to the components of the DEF system. CAUTION: Putting DEF or gasoline into the diesel fuel system will contaminate the entire system and can cause permanent damage to the components of the diesel fuel system. IMPORTANT: Damage to either of these systems due to contamination is not covered by the Nissan New Vehicle Warranty and will be the responsibility of the vehicle owner. Vehicle owners must be extremely careful to put the appropriate fluid/fuel into the appropriate tank.

SERVICE ACTION TO INSPECT THE ROUTING OF THE FUEL TANK BREATHER TUBE ON APPROXIMATELY 6,379SPECIFIC MY2016-17 TITAN XD (A61D) VEHICLES. DURING VEHICLE ASSEMBLY, THE FUEL TANK BREATHER TUBE MAY NOT HAVE PROPERLY ROUTED AND INSTALLED. NO PARTS ARE REQUIRED FOR THIS ACTION."

THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN."

ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

TEMPERATURE SETTING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

only to vehicles equipped with auto A/C. IF YOU CONFIRM The customer states there is a significant difference in vent temperature between auto A/C settings of 61F and 62F. ACTION 1. Check the A/C auto amp?s current part number. 2. If the current part number matches one listed in Table A (see page 6), reprogram the A/C auto amp.

TEMPERATURE SETTING This bulletin applies only to vehicles equipped with dual climate control air conditioning. This bulletin has been amended. APPLIED VINs and DATES have been added, and ACTION has been edited. No other changes have been made. Discard all previous versions of this bulletin.

only to vehicles equipped with climate controlled seats. This bulletin has been amended. The APPLIED VEHICLES section and pages 17 and 18 have changed. No other changes have been made. Please discard previous versions of this bulletin.

to Titan and Titan XD vehicles equipped with climate controlled seats. IF YOU CONFIRM The Climate Controlled (Heated and Cooled) seats do not heat or cool well, or do not work at all. NOTE: This issue, if it should occur, may occur on only the driver seat, or only the front passenger seat, or both front seats. ACTION Refer to the Repair Overview flow chart on page 2.

The Title and APPLIED VEHICLES section have been revised. No other changes have been made. Please discard previous versions of this bulletin.

found to be leaking from one, or more, of the locations listed below, the source(s) of the leak should first be identified and, if possible repaired before the Rear Final Drive Assembly is considered for replacement. A Rear Final Drive Assembly should not be replaced unless bearing, gear, or other significant damage has occurred. Possible points of fluid leaks: Front Oil Seal (Pinion Seal) Axle Tube Seal ABS Rear Wheel Sensor Rear Axle Wheel Bearing Seal Gear Carrier Cover Gasket Drain Plug IMPORTANT: If a Rear Final Drive Assembly is found to have been replaced for a repairable leak and no internal damage is present, the claim will be charged back. Refer to pages 2-5 for additional information that illustrates and/or describes some, but not all, possible points where fluid leaks can occur, as well as helpful service HINTs. This bulletin is only intended as a diagnostic reference and does not direct or imply repair. Refer to the ESM for any applicable repair procedures, if needed.

found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

seal and input seal are available as service parts (see page 2). If a transfer case is leaking from either the input or output seals, first check the fluid to confirm that it is not low, discolored, and/or has an abnormal smell. If the fluid condition indicates that the transfer case has been damaged, the transfer case should be replaced. If the fluid condition is ok, replace only the leaking seal. Refer to the Electronic Service Manual (ESM) for the appropriate seal replacement: TRANSMISSION & DRIVELINE > DRIVELINE > TRANSFER: TX91A. NOTE: Over-repair of the transfer case by replacement may be grounds for warranty chargeback.

service action to reprogram and, if necessary calibrate, the Transmission Control Module (TCM) on specific MY2016-17 Titan XD (A61D) vehicles identified in SERVICE COMM. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. No parts are required for this action. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this inventory service action using Service Comm I.D. PC507. 2. Use the attached procedure to reprogram and, if necessary, calibrate the TCM. Note: Dealers should continue to check new arriving inventory for applicability. 3. Dealers are requested to remedy any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.

Changes have been made throughout. Please discard previous versions of this bulletin.

Steps 13, 16, 17, 19, 22 and 23 have been revised, the APPLIED VEHICLES section has been updated, and page 10 has been created for distribution to the customer. No other changes have been made. Please discard previous versions of this bulletin.

Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Please discard all previous versions of this bulletin.

dragging against the drum surface of the brake rotor and causing noise. ACTION Replace the rear parking brake shoes and retainer springs on both sides of the vehicle. - If the parking brake shoes have worn through their lining and scored either the left side or right side drum surface of the brake rotor, or if any other related damage is present, replace the brake rotor on the affected side and replace the disk brake pads.

No other changes have been made. Please discard all previous versions of this bulletin.

SERVICE INFORMATION The end cap chrome trim (front and rear) on the step rails (running boards) is now available as a separate part (see Parts Information). If the end cap chrome trim needs to be replaced for any reason (fell off, damaged, etc.), replace only the end cap chrome trim. NOTE: - The end cap chrome trim can be replaced without removing the end cap or step pad. - DO NOT replace the entire step rail when only the end cap chrome trim is needed. - Refer to Installation Tips on the next page

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.

Manual (ESM) pages for "Refilling and Air Bleeding Hydraulic System" in the ST-Steering System section have been updated/amended. Until the updated Service Manual is made available, please refer to the link below, as needed, for any service or repairs for the 2016 Titan XD that require Refilling and Air Bleeding the hydraulic power steering system.

trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90 (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.

front passenger seat has a visible vibration/movement that only occurs at speeds between 60 mph and 80 mph And Vibration/movement can be reproduced while driving on smooth roads (vibration/movement not caused by road surface) And All tires are in balance and road force vibration is within specifications (see NTB11-062). ACTION Replace the front passenger seatback assembly and front passenger headrest. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.

Threshhold Bank 1), AND There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.

Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.

specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the 2016 and 2017 Titan Electronic Service Manual (ESM) have been revised. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the revised service information hyperlinked below.

Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.