2004 Nissan Titan TSBs

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Nissan electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.

ACTION Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). NOTE - Do not replace the engine block for this incident if it should occur. See this bulletin for further detail.

* The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not shown). These service parts will require that the valve and valve lifter be replaced at the same time. See this bulletin for further details.

- The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.

The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.

VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

OIL IS LEAKING FROM ONE OR A COMBINATION OF THREE BOLTS AT THE REAR OF THE TRANSFER CASE. IF BOLTS ARE NOT MISSING, DO NOT REPLACE TRANSFER CASE, TRANSFER CONTROL DEVICE; OR TRANSFER CONTROL UNIT FOR THIS INCIDENT, IT SHOULD OCCUR. *PE

WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE

TO PREVENT DAMAGE TO VEHICLE ELECTRONIC COMPONENTS FOLLOW THE INSTRUCTIONS/CAUTIONS. NO MODEL YEARS LISTED. *PE

*TT

*AK

*TT

*JB *SC

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.

ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.

provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.

qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

*TT

NISSAN. *TT

PEDAL HEIGHT ADJUSTMENT. *TT UPDATED *EH

THIS BULLETIN REPLACES NTB03-101. *TT

*TT

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

(LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.

"RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.

The reprogramming procedure has been revised. No other changes have been made. Discard all previous versions of this bulletin.

INTRODUCTION Nissan is conducting a voluntary service campaign on certain specific model year 2004- 2011 Titan, and 2005-2011 Frontier and Xterra vehicles to reprogram the air bag diagnosis sensor unit. This repair will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P7318 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

APPLIES TO ALL 2004 AND LATER (DOES NOT APPLY TO LEAF/EV) VEHICLES. *JS

THE HOSE NOW COMES WITHOUT THE PRESSURE SENSOR. DO NOT DAMAGE PRESSURE SENSOR UPON REMOVAL. IF ONLY PRESSURE SENSOR NEEDS REPLACEMENT, DO NOT REPLACE HOSE. *JS

ENHANCED ELECTRONIC CIRCUITRY WHICH MAY HELP FURTHERPROTECT A VEHICLE FROM DAMAGE OR FIRE CAUSED BY A SHORT CIRCUIT IN THE ELECTRICAL SYSTEM OF A TOWED TRAILER. *TT

ALSO INCLUDING 2005 ALL NISSAN VEHICLES. *TT

*MR THIS BULLETIN REPLACES NTB04-056 DATED 5/15/2004. *TT

*TT

VARIOUS MODELS INCLUDING THE 2004 PATHFINDER ARMADA. *TT

Please discard previous versions of NTB17-110.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

*JS

DIAGNOSE BY EVALUATING THE U JOINT WITH THE PROPELLER SHAFT REMOVED. REPLACE THE U JOINT (JOURNAL/JOURNAL BEARINGS). *PE

*NJ

*KB

*TT

*TT

*TT

*TT

*TT

*TT

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.

off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.

vehicle is equipped with the correct tires as shown on the TIRE AND LOADING INFORMATION LABEL on the driver side body side outer panel (B-pillar), (see Figure A). AND All 4 tires have been verified to be within specification for RH1 uniformity at or below 118 N (12 kg, 26.5 lbs.) as described in NTB11-062. ACTION Replace the 2 rearmost cab body mounts, nuts, and bolts with the new ones listed in the PARTS INFORMATION section of this bulletin.

The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.

OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE

*TT

*TT

PC944, PC946, PC947, PC949 APPLIED VEHICLES: 2004-2012 Armada (TA60) 2004-2009 Quest (V42) 2004-2012 Titan (A60) Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2004-2012 Armada, 2004-2012 Titan, and 2004-2009 Quest vehicles, to inspect and if necessary, replace the driver Air Bag Cover. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers PC944, PC946, PC947 and PC949 to this campaign. The vehicle specific number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealers inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

correctly, and/or the rear audio speakers are not working correctly, and/or the customer has requested an inspection of the above items, ACTIONS 1. Check Service Comm to determine if Campaign R0616 has been performed. - If campaign R0616 has not been performed, this bulletin does not apply. 2. Follow the Repair Flow-Chart in this bulletin. See this bulletin for further detail. (PC198)

2017 has been revised: - Dealers may now use revised TSB NTB17-070 to resume repair of 2004-2006 model year vehicles. Please discard previous versions of this bulletin

Nissan is conducting a Voluntary Service Campaign to reprogram the Air Bag Control Unit (ACU) in 2004-2014 Titan, 2005-2014 Frontier, and 2005-2014 Xterra vehicles. The current ACU rollover-sensing calibration logic could allow for unintended curtain air bag deployment in rare instances occurring under certain unique driving scenarios, usually involving unpaved roads or off-road where one side of the vehicle is higher than the other. The ACU reprogramming will improve rollover-sensing calibration to address certain unique driving scenarios, and help prevent unintended curtain air bag deployment, while maintaining the design intent for deployment in rollover crashes. Owners of affected vehicles will be notified beginning in June 2017 and asked to bring their vehicle to an authorized Nissan dealer to have the remedy work completed at no cost to the owner.

to ASIST at 3:00 PM Central Time to address concerns with some vehicles not being able to complete the reprogramming. This software will be released automatically overnight, but dealers can download the new software immediately by manually syncing their ASIST on their CONSULT III to acquire the latest updates.

*PE

CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS ON ALL NISSAN MODELS WITH THE SRS SYSTEMS. *PE UPDATED 2/21/14. *PE

(THIS BULLETIN UPDATES NTB04-003.) *TT

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

suspension leaf springs when driving. NOTE: - Noise is more pronounced when driving over rough roads below 30 mph. - Chassis ears may be helpful to isolate this noise. - If the source of the squeak or tick noise is NOT either the left or right side leaf spring, this bulletin does not apply. Refer to ASIST for further diagnostic and repair information. ACTION: Clean the rear leaf spring tip inserts.

2017 has been revised to include: - Claims information for unintended airbag deployment (related to campaign) Temporary suspension of this campaign on all affected 2004-2006 model year vehicles is still in affect - Nissan is aware of reprogramming concerns on 2004-2006 models subject to P7318 Air Bag Control Unit Reprogramming and is working diligently with the supplier to provide a solution. - In the interim, Nissan recommends dealers suspend reprogramming activity on all 2004-2006 models until a software remedy is available. These models will continue to be identified in Service Comm and DBS National Service History with an open P7318 campaign. Nissan will provide an update as soon as revised software is available. Please discard previous versions of this bulletin

Nissan is aware of reprogramming concerns on 2004-2006 models subject to P7318 Air Bag Control Unit Reprogramming and is working diligently with the supplier to provide a solution. In the interim, Nissan recommends dealers suspend reprogramming activity on all 2004-2006 models until a software remedy is available. These models will continue to be identified in Service Comm and DBS National Service History with an open P7318 campaign. Nissan will provide an update as soon as revised software is available. Please discard previous versions of this bulletin.

service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.

*TT

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

A NOISE (CLUNKING, SQUEAKING, POPPING) CAN BE HEARD WHEN PERFORMING AT LEAST ONE OF THE FOLLOWING ACTIONS: TURNING THE STEERING WHEEL LEFT OR RIGHT, DRIVING OVER SPEED BUMPS, DRIVING ON ROUGH ROADS, ACCELERATING OR DECELERATING AND NOISE IS COMING FROM THE FRONT STABILIZER BAR BUSHING. *PE

A VIBRATION IS FELT IN THE STEERING WHEEL (OTHER THAN SHIMMY) AND/OR FLOOR AND/OR SEATS WHEN DRIVING AT A SPEED BETWEEN APPROXIMATELY 25MPH AND APPROXIMATELY 40MPH ONLY. *PE

*TT

The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.

AFFECTING ALL VEHICLES 2003-11 EXCEPT LEAF, EQUIPPED WITH NAVIGATION SYSTEM. CUSTOMER IS MAILED UPDATE DISC(S) OR SD CARD AND INSTALLS DATA; DEALERSHIP IS MAILED UPDATE DISC(S) AND THE DEALERSHIP INSTALLS DATA WHEN VEHICLE IS BROUGHT IN. *PE

*TT

THIS BULLETIN HAS BEEN AMENDED. THE FORMAT OF THE APPLIED VINS WAS CHANGED. *TT

*TT

We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

*PE

*TT

*TT

ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

*TT

*JB

These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.

The new service part (B in Figure 1) is visually different, but is a direct replacement for the original equipment part. IMPORTANT: See page 2 for the procedure to inspect the cap bolt service part for excessive stretch. If replacement of a single connecting rod cap bolt is indicated for any given connecting rod, both connecting rod cap bolts of the affected connecting rod must be replaced as a set.

VEHICLES WITH BUCKET SEATS ONLY. *NJ

NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB

*KB

*NM

leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.

2004 TO CURRENT NISSAN VEHICLES. *NJ

etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.

*EH UPDATE *SC