2017 Nissan Sentra TSBs

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Please discard previous versions of NTB20-082.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

sensor, fuel filter and fuel pump assembly (fuel pump assembly) needs to be replaced, due to an in tank fuel level sensor issue or fuel temp sensor DTC, the fuel level sensor (includes fuel temp sensor) can be ordered separately from the fuel pump assembly. Refer to the Electronic Service Manual (ESM) for the service procedure to remove the fuel pump assembly. Sentra: PDF ESM ENGINE > FL Fuel System > MRA8DE (or) MR16DDT > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUP ASSEMBLY > Removal and Installation. Web based ESM ENGINE > FUEL SYSTEM > MRA8DE (or) MR20DE > REMOVAL AND INSTALLATION > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY. NV200 and Taxi: PDF ESM ENGINE > FL Fuel System > MR20DE > REMOVAL AND INSTALLATION > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY > Removal and Installation. Web based ESM ENGINE > FUEL SYSTEM > MR20DE > REMOVAL AND INSTALLATION > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY> Removal and Installation.

ignition switch and applying the brake pedal. ACCESSORY and IGNITION ON modes can be turned on and off with the no start condition present. The stop lamps will be inoperative with the no-start condition present. ACTION Install a new brake lamp switch and install a rubber grommet with the parts listed in PARTS INFORMATION on the last page of this bulletin.

variable transmissions (CVTs), and to address customer concerns including those expressed by customers in the class actions, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). The extension also includes rental while CVT repairs or replacements are completed. Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissans New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension as part of the class action settlements, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992, option 2) for any vehicles requiring CVT replacements when the replacement cost exceeds a Dealers Claims Administration/Authorization Limits (DCAL). Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty.

and ASIST to determine the appropriate repair for a customers concern. Nissan recommends CVT assembly replacement be offered whenever diagnostics have led a dealer to determine a belt and pulley sub assembly repair will resolve a customers concern and the vehicle time in service or mileage is equal to or greater than 84 months in service or 84,000 miles. This recommendation provides longer-term durability for customer satisfaction. Customers required to pay out-of-pocket for these repairs may still choose belt and pulley sub assembly repair in lieu of CVT unit replacement if they prefer that option. Note: This recommendation only applies to belt and pulley sub assembly repairs. Do not recommend CVT unit replacement when the diagnosis is for software updates or control valves.

We strive to provide you with an excellent ownership experience that includes confidence in your vehicles performance, features and overall reliability. To that end, Nissan is extending the limited warranty covering your continuously variable transmission (CVT) to 7 years/84,000 miles, whichever comes first. This warranty extension is being provided as an owner satisfaction effort to address concerns, including those expressed by plaintiffs in class action litigation. This CVT warranty extension covers your CVT assembly (including internal CVT components, gaskets, and seals, CVT control valve body, and torque converter), cooler kit (if applicable), and any necessary software updates. Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissans New Vehicle Limited Warranty continue to apply. What You Should Do This extended warranty coverage is effective immediately. You do not need to take any further action. The Sentra with the Vehicle Identification Number listed at the top of this page is covered by this extended CVT warranty. If you seek coverage for a repair under this extended warranty, you will need to bring your vehicle to an authorized Nissan dealer. The factorytrained technical staff at the Nissan dealer will have the diagnostic tools and knowledge to provide you with the appropriate service and submit your warranty claim As you take care of yourself and your family during the COVID-19 crisis, we know that your vehicle may play a key role. We are here to help if you need us. Service Department hours of operation may be modified as local and state restrictions change, so we encourage you to book your appointment online or call your local Dealership to confirm service availability.

Nissan is conducting a Voluntary Emissions Service Campaign on approximately 104,221 specific Nissan vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or Smog Check test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History Open Campaigns I.D. P9328 Affected Model Year 2015 P9343 Affected Model Year 2016 P9345 Affected Model Year 2017 P9347 Affected Model Year 2018 P9349 Affected Model Year 2019 2. Dealers should remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction.

conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9345, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealers inventory.

conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9435, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealers inventory.

SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

vehicles eqiupped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY below. Discard all previous versions of this bulletin.

now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedure in this bulletin is different than those that are currently in the Electronic Service Manuals (ESMs), which will be updated with this information at a later date.

vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. A TCM P/N was added to 2015 Sentra in Table A. No other changes were made. Discard all previous versions of this bulletin.

vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. A TCM P/N was added to 2015 Sentra in Table A. No other changes were made. Discard all previous versions of this bulletin.

INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2013-2017 Sentra vehicles that are currently registered in the states of Arizona or Nevada. 2013- 2014 Sentra vehicles will have the PCV valve replaced, and the Engine Control Module (ECM) software reprogrammed. 2015-2017 Sentra vehicles will have the ECM software reprogrammed only. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers PM827 and PC633 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

Campaign Summary***** Nissan is conducting a Regional Voluntary Service Campaign to reprogram the Engine Control Module (ECM) on affected vehicles currently registered in Nevada and Arizona. The current programming may cause the air/fuel ratio to become excessively rich resulting in engine stop under certain high temperature and high altitude conditions. In addition, Nissan is asking dealers to inspect and, if necessary, replace the Positive Crankcase Ventilation (PCV) valve on certain 2013-14 Nissan Sentra vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. Due to the various models involved and the associated responsible manufacturing location of origin, there are three (3) separate campaign IDs with unique Campaign Bulletins for each model: - PC633 - PM827 - P8325 New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information NOTE: These campaigns are state-specific and limited to vehicles that are currently registered, or previously registered, in the state of Nevada or Arizona only. 2. Nissan requests dealers repair any affected vehicles in retailer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use the appropriate repair bulletin for the applicable model as listed below to correct any vehicles subject to this campaign. 4. Once repaired, dealer should submit a warranty claim and release the vehicle.

This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.

MORE) This bulletin has been amended. Table A on page 4 has been revised, and additional information has been applied to step 7. No other changes have been made. Please discard previous versions of this bulletin.

Additional model years were added on pages 1, 3, 7, 15, and 39. Other minor changes were made on page 19, 20, 34, and 38. Please discard all previous versions of this bulletin.

a CVT (Continuously Variable Transmission). This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.

date code on the cooling fan blade and, if necessary, replace the cooling fan shroud and motor assembly on 159 specific 2017 Sentra vehicles. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to inspect and, if necessary, remedy the affected vehicles prior to sale to help ensure customer satisfaction. *****What Dealers Should Do***** 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History ? Open Campaign I.D. PM700 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to inspect the vehicle and, if necessary, repair. 3. The service department should submit the applicable warranty claim for the action(s) performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealer?s responsibility to check Service Comm or DBS National Service History - Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory. Nissan requests dealers to perform this repair on new vehicles in inventory prior to being retailed to help ensure customer satisfaction.

equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. Changes were made to APPLIED VEHICLES, PARTS INFORMATION, and pages 3, 7, and 15. Discard all previous versions of this bulletin.

control valve replacement, additional service must be completed with CONSULT-III plus (C-III plus). - The original calibration data must first be erased from the TCM and then newcalibration data written. - If the calibration data is not erased, the vehicle can experience drivability concernswhich may result in a CVT issue. Additional Service when Replacing Control Valve or Transaxle Assembly - The following procedures, starting on the next page, must be performed in thisorder. - Check off procedure as they are performed in the order listed below.

ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. CLAIMS INFORMATION has been revised. No other changes have been made. Discard all previous versions of this bulletin.

This bulletin has been amended to update the Applied Vehicles and Table A on page 4. No other changes were made. Please discard previous versions of this bulletin.

IF YOU CONFIRM The engine turns OFF or hesitates when accelerating from a stop during hot ambient temperatures (100F or more), AND The engine is able to be restarted. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.

Continuously Variable Transmission (CVT). This bulletin has been amended throughout. Discard all previous versions of this bulletin.

This bulletin has been amended. The Title and APPLIED VEHICLES section have been revised, and a PARTS INFORMATION section has been added. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service Manual [ESM]). Whenever checking, filling, or topping off a CVT's fluid level of an applied vehicle for any reason, use the procedure outlined in the appropriate section of the ESM. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

current and former owners and lessees of the following vehicles will receive a postcard from a Settlement Administrator informing them of the terms of a proposed class action that, subject to final court approval, could extend the warranty on the CVT for the following vehicles: 2012-2017 Versa Sedan (N17) 2014-2017 Versa Note (E12) 2013-2017 Sentra (B17) 2013-2016 Altima (L33) 2013-2017 Juke (F15) The proposed settlement (including the proposed warranty extension) is still subject to final approval by the court presiding over the proposed settlement. The court will determine if the settlement will be approved at or shortly after a hearing that is scheduled for March 6, 2020. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension and you should proceed with CVT-related claims as outlined below in #3 under what dealers should do. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, it is strongly recommended that you refer customers to the websites and/or telephone numbers listed below so that they can receive information from appropriate sources and in order to avoid providing incorrect and/or incomplete information. The telephone numbers and websites should be active by November 1, 2019. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions if and when the proposed settlement is approved.

multiple bumps or vibration), hesitation on acceleration, lack of power or RPM flare. ACTION Refer to the Repair Overview on pages 2 and 3.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

equipped with a CVT (Continuously Variable Transmission). IF YOU CONFIRM The MIL is ON with DTC P0776 (PC SOLENOID B ? Pressure Control Solenoid ?B? Performance/Stuck OFF) stored. NOTE: - If P0744, P0746, P0841, P0965, P2813, or P17F0 are stored this bulletin does not apply. Refer to ASIST for diagnostic assistance. - With this incident, if it should occur, P1715 (INPUT SPEED SENSOR) may be stored with DTC P0776. The vehicle may also hesitate and/or have reduced power. ACTION 1. Refer to the Repair Flow Chart on page 2 for mechanical CVT repair. 2. If needed, reprogram the TCM. - Refer to step 30 in the TCM Reprogram section (page 21) of the SERVICE PROCEDURE to confirm if reprogramming is needed. 3. Perform Additional Service (page 19).

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

bulletin applies only to vehicles eqiupped with a CVT (Continuously Variable Transmission). This bulletin has been amended to add a special tool to page 6 and the procedure to use the tool to pages 77-79. No other changes were made. Please discard previous versions of this bulletin.

may be diagnosed incorrectly upon initial inspection causing incorrect parts replacement such as oil pan gaskets, axle seals, etc. To help reduce/eliminate the possible return of an applied vehicle, first check for leakage around the CVT fluid charging pipe. When leakage is determined to be coming from the base of the CVT fluid charging pipe, remove it to inspect, and if necessary, replace the O-ring. If needed, CVT leak inspection dye may be used to determine the source of the leak. - Refer to NTB09-140. See example photos on pages 2 and 3.

SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.

applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended to update Table B and add a DTC under If You Confirm. No other changes were made. Please discard previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

This bulletin has been amended. The Applied Vehicles have been updated and Claims Information has been added. No other changes were made. Please discard previous versions of this bulletin.

applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended to add model years to Applied Vehicle, update Table B and make changes to page 116. No other changes were made. Please discard previous versions of this bulletin.

applies to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended to update Table B and make changes to pages 2, 6, 9 and 10. Please discard previous versions of this bulletin.

Changes have been made in Applied Vehicles, Parts Information, Claims Information, and changes on pages 94, 103, 116, 125, and 126. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

Changes have been made on pages 2, 3, 9, 17, 23, 34, 35, 43, 44, 45, 83, 86 and 89 through 126. Please discard previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

This bulletin has been amended to make minor changes on pages 22, 27, 34, 43, 63, 91, and 103. Please discard previous versions of this bulletin.

shudder, single or multiple bumps or vibration), hesitation on acceleration, lack of power or RPM flare. AND/OR One of these DTCs is stored. - P0746 (PRES CNT SOL/A FCTN (L/PRESS SOL/FNCTN)) - P0965 (PRESSURE CONTROL SOLENOID B) ACTION - Refer to the Repair Overview on page 2. CAUTION: Always handle the CVT and component assemblies carefully.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section and Table A have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and bug fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on page 14. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin

See Amendment History on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on page 9. Please discard previous versions of this bulletin.

The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.

vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.

vehicles equipped with non-NAVI audio system. IF YOU CONFIRM One or more of the audio preset buttons of an applied vehicle sticks down (does not pop up after pushing down) or is slow to move back to its rest position after pushing down. ACTION Reposition, or replace as necessary, the felt tape on the cluster lid C.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.

This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.

The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.

C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message Unavailable Front Radar Obstruction or Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owners Manual

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly (fuel pump assembly). The fuel level sensor can be replaced separately. P0460 (FUEL LEV SEN SLOSH) P0461 (FUEL LEVEL SENSOR) P0462 (FUEL LEVL SEN/CIRC) P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

With an active NissanConnectSM Services subscription, the TCU communicates with the NissanConnectSM Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. See this bulletin for further detail.

This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on page 5. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

See Amendment History on the last page. Please discard previous versions of this bulletin.

vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.

ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

Information for 2017 Altima, Murano, Pathfinder, Sentra, and Titan/Titan XD vehicles has been applied. No other changes have been made. Please discard previous versions of this bulletin.

The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Ts 3G network connection, including Nissan Group, have had connectivity services affected. NissanConnect Services are no longer available on the APPLIED VEHICLES listed above.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

No other changes have been made. Please discard previous versions of this bulletin.

device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.

Assurance Hold certain MY2017 Sentra (B17) vehicles. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. An inspection procedure is now available. Nissan is requesting that dealers inspect the accelerator pedal part lot number on all affected inventory and, if necessary, remedy affected inventory using the procedure included with this announcement. The quality hold can be released once the vehicle inspection and, if necessary, repair has been completed. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this inventory service action using Service Comm I.D. PM666. - New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information 2. Use the attached procedure to inspect the part lot number, and if matched, replace the subject part. - If part replacement is not needed, dealers may submit the inspection claim, and release the vehicle for sale with no further action. - If part replacement is needed, dealers will need to order parts using an SVC order in DCS. - Once the vehicle has been repaired, submit the claim, using the claims coding provided in the repair procedure, and release the vehicle. Do not submit the claim until parts have been received and the vehicle has been remedied. - Parts replaced under this campaign activity may be collected. Follow the attached inspection procedure prior to determining the necessity of replacing any parts. NOTE: Dealers should continue to check new arriving inventory for applicability. 3. Dealers are requested to inspect and, if necessary, remedy any affected vehicle in dealer new or pre-owned inventory prior to sale to ensure customer satisfaction.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.

not show FULL after filling with fuel. AND/OR DTC P00FE EVAP CONTROL SYSTEM is stored. ACTION Replace the fuel tank with the new one listed in the PARTS INFORMATION section of this bulletin. - Refer to the Electronic Service Manual (ESM), section FE ? FUEL SYSTEM.

for any reason, you must use the information in this bulletin to determine the correct replacement part number. First, determine the vehicle emission specification using FAST (see page 2). Then select the replacement EVAP canister using the following table.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Automatic Emergency Braking (AEB) or Forward Emergency Braking (FEB). SERVICE INFORMATION If the following ICC/ADAS codes are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.

This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.

This commitment requires Nissan to periodically place certain specific vehicles on a temporary Quality Assurance (QA) Hold to assure that these vehicles, as delivered to our customers, meet our exacting standards and our customers? expectations. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on approximately 4,066 specific MY2017 Sentra (B17) vehicles. Nissan has learned that specific accelerator pedals may not be manufactured to specification and is investigating this concern. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this QA Hold using Service Comm I.D. PM666 Note: Dealers should continue to check new arriving inventory for QA Hold applicability. 2. Please do not drive, sell, or trade the specific 2017 Sentra vehicles in Dealer Inventory subject to this QA Hold. 3. No further action is necessary at this time. Nissan will provide an update by February 3, 2017.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.