2016 Nissan Sentra TSBs

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Dealer Announcement: Nissan is conducting a Voluntary Emission Service Campaign to reprogram the Engine Control Module (ECM) and inspect the oxygen (O2) sensor voltage on certain MY2013-2016 Nissan Sentra SULEV vehicles identified in Service Comm. If the voltage is OK, no repair is necessary. If the voltage check results are No Go, dealers will diagnose and repair per the electronic service manual (ESM), and remedy any diagnostic trouble codes (DTCs) that may have been masked by a failure to detect the short circuit to ground condition. The current level software installed on the affected vehicles may not detect a rear oxygen (O2) sensor short to ground (SCG) condition. Undetected SCG may result in failure to pass emissions testing. What Dealers Should Do: 1.Verify if vehicles are affected by this Voluntary Emission Service Campaign using Service Comm or DBS National Service History Open Campaigns I.D. P1A25. 2.Dealers are requested to remedy any affected vehicles in dealer pre-owned inventory to ensure customer satisfaction. 3.Dealers should use NTB22-006 to correct any vehicles subject to this campaign. 4.Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.

Please discard previous versions of NTB20-082.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

sensor, fuel filter and fuel pump assembly (fuel pump assembly) needs to be replaced, due to an in tank fuel level sensor issue or fuel temp sensor DTC, the fuel level sensor (includes fuel temp sensor) can be ordered separately from the fuel pump assembly. Refer to the Electronic Service Manual (ESM) for the service procedure to remove the fuel pump assembly. Sentra: PDF ESM ENGINE > FL Fuel System > MRA8DE (or) MR16DDT > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUP ASSEMBLY > Removal and Installation. Web based ESM ENGINE > FUEL SYSTEM > MRA8DE (or) MR20DE > REMOVAL AND INSTALLATION > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY. NV200 and Taxi: PDF ESM ENGINE > FL Fuel System > MR20DE > REMOVAL AND INSTALLATION > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY > Removal and Installation. Web based ESM ENGINE > FUEL SYSTEM > MR20DE > REMOVAL AND INSTALLATION > FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY> Removal and Installation.

ignition switch and applying the brake pedal. ACCESSORY and IGNITION ON modes can be turned on and off with the no start condition present. The stop lamps will be inoperative with the no-start condition present. ACTION Install a new brake lamp switch and install a rubber grommet with the parts listed in PARTS INFORMATION on the last page of this bulletin.

variable transmissions (CVTs), and to address customer concerns including those expressed by customers in the class actions, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). The extension also includes rental while CVT repairs or replacements are completed. Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissans New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension as part of the class action settlements, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992, option 2) for any vehicles requiring CVT replacements when the replacement cost exceeds a Dealers Claims Administration/Authorization Limits (DCAL). Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty.

and ASIST to determine the appropriate repair for a customers concern. Nissan recommends CVT assembly replacement be offered whenever diagnostics have led a dealer to determine a belt and pulley sub assembly repair will resolve a customers concern and the vehicle time in service or mileage is equal to or greater than 84 months in service or 84,000 miles. This recommendation provides longer-term durability for customer satisfaction. Customers required to pay out-of-pocket for these repairs may still choose belt and pulley sub assembly repair in lieu of CVT unit replacement if they prefer that option. Note: This recommendation only applies to belt and pulley sub assembly repairs. Do not recommend CVT unit replacement when the diagnosis is for software updates or control valves.

We strive to provide you with an excellent ownership experience that includes confidence in your vehicles performance, features and overall reliability. To that end, Nissan is extending the limited warranty covering your continuously variable transmission (CVT) to 7 years/84,000 miles, whichever comes first. This warranty extension is being provided as an owner satisfaction effort to address concerns, including those expressed by plaintiffs in class action litigation. This CVT warranty extension covers your CVT assembly (including internal CVT components, gaskets, and seals, CVT control valve body, and torque converter), cooler kit (if applicable), and any necessary software updates. Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissans New Vehicle Limited Warranty continue to apply. What You Should Do This extended warranty coverage is effective immediately. You do not need to take any further action. The Sentra with the Vehicle Identification Number listed at the top of this page is covered by this extended CVT warranty. If you seek coverage for a repair under this extended warranty, you will need to bring your vehicle to an authorized Nissan dealer. The factorytrained technical staff at the Nissan dealer will have the diagnostic tools and knowledge to provide you with the appropriate service and submit your warranty claim As you take care of yourself and your family during the COVID-19 crisis, we know that your vehicle may play a key role. We are here to help if you need us. Service Department hours of operation may be modified as local and state restrictions change, so we encourage you to book your appointment online or call your local Dealership to confirm service availability.

SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

vehicles eqiupped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY below. Discard all previous versions of this bulletin.

now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedure in this bulletin is different than those that are currently in the Electronic Service Manuals (ESMs), which will be updated with this information at a later date.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. A TCM P/N was added to 2015 Sentra in Table A. No other changes were made. Discard all previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. A TCM P/N was added to 2015 Sentra in Table A. No other changes were made. Discard all previous versions of this bulletin.

INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2013-2017 Sentra vehicles that are currently registered in the states of Arizona or Nevada. 2013- 2014 Sentra vehicles will have the PCV valve replaced, and the Engine Control Module (ECM) software reprogrammed. 2015-2017 Sentra vehicles will have the ECM software reprogrammed only. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers PM827 and PC633 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

Campaign Summary***** Nissan is conducting a Regional Voluntary Service Campaign to reprogram the Engine Control Module (ECM) on affected vehicles currently registered in Nevada and Arizona. The current programming may cause the air/fuel ratio to become excessively rich resulting in engine stop under certain high temperature and high altitude conditions. In addition, Nissan is asking dealers to inspect and, if necessary, replace the Positive Crankcase Ventilation (PCV) valve on certain 2013-14 Nissan Sentra vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. Due to the various models involved and the associated responsible manufacturing location of origin, there are three (3) separate campaign IDs with unique Campaign Bulletins for each model: - PC633 - PM827 - P8325 New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information NOTE: These campaigns are state-specific and limited to vehicles that are currently registered, or previously registered, in the state of Nevada or Arizona only. 2. Nissan requests dealers repair any affected vehicles in retailer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use the appropriate repair bulletin for the applicable model as listed below to correct any vehicles subject to this campaign. 4. Once repaired, dealer should submit a warranty claim and release the vehicle.

This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.

MORE) This bulletin has been amended. Table A on page 4 has been revised, and additional information has been applied to step 7. No other changes have been made. Please discard previous versions of this bulletin.

Additional model years were added on pages 1, 3, 7, 15, and 39. Other minor changes were made on page 19, 20, 34, and 38. Please discard all previous versions of this bulletin.

a CVT (Continuously Variable Transmission). This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.

equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. Changes were made to APPLIED VEHICLES, PARTS INFORMATION, and pages 3, 7, and 15. Discard all previous versions of this bulletin.

control valve replacement, additional service must be completed with CONSULT-III plus (C-III plus). - The original calibration data must first be erased from the TCM and then newcalibration data written. - If the calibration data is not erased, the vehicle can experience drivability concernswhich may result in a CVT issue. Additional Service when Replacing Control Valve or Transaxle Assembly - The following procedures, starting on the next page, must be performed in thisorder. - Check off procedure as they are performed in the order listed below.

Please discard the previous versions of this bulletin.

ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. CLAIMS INFORMATION has been revised. No other changes have been made. Discard all previous versions of this bulletin.

This bulletin has been amended to update the Applied Vehicles and Table A on page 4. No other changes were made. Please discard previous versions of this bulletin.

Continuously Variable Transmission (CVT). This bulletin has been amended throughout. Discard all previous versions of this bulletin.

IF YOU CONFIRM THE ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100F), AND THE ENGINE IS ABLE TO BE RESTARTED. ACTION 1. FOR 2013 AND 2014 SENTRA ONLY: - INSPECT THE COLOR OF THE PCV VALVE, AND REPLACE IF THE COLOR IS ORANGE (SEE FIGURE A ON PAGE 2). 2. FOR ALL APPLIED VEHICLES, IF NEEDED, REPROGRAM THE ECM. - REFER TO STEP 6 IN THE ECM REPROGRAM SECTION OF THE SERVICE PROCEDURE TO CONFIRM IF REPROGRAMMING IS NEEDED."

VEHICLES MAY DEVELOP A CRACK IN THE RUBBER DURING ITS NORMAL SERVICE LIFE. - REFER TO FIGURES 2 AND 3 ON PAGE 2 FOR THE REAR TORQUE ROD LOCATION ON THE VEHICLE. FIGURE 1 SHOWS A CRACK IN THE RUBBER OF THE FORWARD END OF THE REAR TORQUE ROD THAT DOES NOT EXTEND THE COMPLETE CIRCUMFERENCE (ALL THE WAY AROUND) THE RUBBER. THIS MAY OCCUR DURING NORMAL SERVICE LIFE. - DO NOT REPLACE THE TORQUE ROD FOR A CRACK THAT DOES NOT EXTEND ALL THE WAY AROUND THE RUBBER PART OF THE FORWARD END. NOTE: FOR 2013-2014 SENTRA WITH A ROUGH IDLE, REFER TO NTB15-057."

found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

And/or * The Shifter will not move out of park. NOTE: For Rogue (T32), it is possible that shifter selector knob may not be installed correctly. Please refer to NTB14-058 for shift selector knob service information before applying this bulletin. ACTION a. Adjust the key interlock cable. b. Adjust the stop lamp switch. NOTE: Nissan vehicle warranty does not cover incidents due to lack of vehicle maintenance and/or physical damage. Refer to New Vehicle Limited Warranty in the Nissan Assurance Products Resource Manual (APRM) for warranty coverage guidelines and complete information regarding warranty coverage. Please see this bulletin for further details.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

current and former owners and lessees of the following vehicles will receive a postcard from a Settlement Administrator informing them of the terms of a proposed class action that, subject to final court approval, could extend the warranty on the CVT for the following vehicles: 2012-2017 Versa Sedan (N17) 2014-2017 Versa Note (E12) 2013-2017 Sentra (B17) 2013-2016 Altima (L33) 2013-2017 Juke (F15) The proposed settlement (including the proposed warranty extension) is still subject to final approval by the court presiding over the proposed settlement. The court will determine if the settlement will be approved at or shortly after a hearing that is scheduled for March 6, 2020. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension and you should proceed with CVT-related claims as outlined below in #3 under what dealers should do. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, it is strongly recommended that you refer customers to the websites and/or telephone numbers listed below so that they can receive information from appropriate sources and in order to avoid providing incorrect and/or incomplete information. The telephone numbers and websites should be active by November 1, 2019. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions if and when the proposed settlement is approved.

multiple bumps or vibration), hesitation on acceleration, lack of power or RPM flare. ACTION Refer to the Repair Overview on pages 2 and 3.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

bulletin applies only to vehicles eqiupped with a CVT (Continuously Variable Transmission). This bulletin has been amended to add a special tool to page 6 and the procedure to use the tool to pages 77-79. No other changes were made. Please discard previous versions of this bulletin.

may be diagnosed incorrectly upon initial inspection causing incorrect parts replacement such as oil pan gaskets, axle seals, etc. To help reduce/eliminate the possible return of an applied vehicle, first check for leakage around the CVT fluid charging pipe. When leakage is determined to be coming from the base of the CVT fluid charging pipe, remove it to inspect, and if necessary, replace the O-ring. If needed, CVT leak inspection dye may be used to determine the source of the leak. - Refer to NTB09-140. See example photos on pages 2 and 3.

applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended to update Table B and add a DTC under If You Confirm. No other changes were made. Please discard previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

This bulletin has been amended. The Applied Vehicles have been updated and Claims Information has been added. No other changes were made. Please discard previous versions of this bulletin.

applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended to add model years to Applied Vehicle, update Table B and make changes to page 116. No other changes were made. Please discard previous versions of this bulletin.

applies to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended to update Table B and make changes to pages 2, 6, 9 and 10. Please discard previous versions of this bulletin.

Changes have been made in Applied Vehicles, Parts Information, Claims Information, and changes on pages 94, 103, 116, 125, and 126. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message Unavailable Front Radar Obstruction or Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owners Manual

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly (fuel pump assembly). The fuel level sensor can be replaced separately. P0460 (FUEL LEV SEN SLOSH) P0461 (FUEL LEVEL SENSOR) P0462 (FUEL LEVL SEN/CIRC) P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

satisfaction, Nissan is providing a limited warranty extension to certain MY2013-2016 Nissan Altima 2.5L (SULEV and 50 states emissions) and certain MY2013-2016 Nissan Sentra vehicles (50 states only) to allow for annual rear oxygen sensor voltage checks, upon request, to determine if a rear oxygen sensor short-to-ground condition exists. If a rear oxygen sensor short-to ground condition exists, Nissan will inspect and repair or replace, as necessary, the sensor or wiring and remedy any diagnostic trouble codes that may have been masked by a failure to detect a possible rear oxygen (O2) sensor short to ground (SCG) condition. If those DTCs are first found only after a short-to-ground repair, the Limited Emission Warranty extension will cover the costs of parts and labor to inspect and repair the corresponding issue(s). Affected vehicles may fail to detect the rear oxygen (O2) sensor short circuit to ground (SCG). Undetected SCG may result in failure to pass emissions testing. Owners of eligible vehicles will receive a notification indicating their eligibility for the following: Annual rear oxygen sensory voltage check during the extended warranty coverage Limited warranty extension for the rear oxygen sensor to 20 years/200,000 miles (whichever occurs first) What Dealers Should Do: 1.Verify if vehicles are eligible for this limited Warranty Extension using the warranty extension page of Service Comm. 2.Dealers should perform a voltage check and, if necessary, remedy any eligible vehicles subject to this warranty extension to ensure customer satisfaction using NTB22-007. 3.The service department should submit the applicable warranty claim for the action(s) performed.

providing the highest levels of product quality and customer satisfaction. Therefore, Nissan is extending the emission warranty on the Rear Oxygen Sensor in the case of a short-to-ground condition to 20 Years or 200,000 miles, whichever occurs first. All other warranty terms, limitations, and conditions remain unchanged. During the warranty extension period, customers are eligible for annual Rear Oxygen Sensor voltage checks, upon request, to determine if a Rear Oxygen Sensor short-toground condition exists. If a Rear Oxygen Sensor short-to-ground condition does exist, Nissan will inspect and repair or replace, as necessary, the sensor or wiring and inspect for the existence of specific Diagnostic Trouble Codes (DTCs) for issues that may have been previously unidentified due to the short-to-ground condition. Only if one of the DTCs in Table A are first found after a short-to-ground repair, the corresponding issue(s) will also be corrected according to the service manual at no charge for parts and labor as part of this warranty extension.

INTRODUCTION Nissan is conducting this voluntary emission service campaign, on certain specific model year 2013-2016 Sentra vehicles, to reprogram the ECM (if applicable), and then inspect the oxygen (O2) sensor voltage. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P1A25 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourist) owners, and vehicles in a dealers inventory.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

With an active NissanConnectSM Services subscription, the TCU communicates with the NissanConnectSM Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. See this bulletin for further detail.

logic that controls the Occupant Classification System (OCS) and 'passenger airbag indicator' (PABI), as described in the Owner?s Manual. This TSB applies only to vehicles using the 2-sensor OCS. Those changes are: * PABI light is ON with an empty front passenger seat. Please see this bulletin for further details.

This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on page 5. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

See Amendment History on the last page. Please discard previous versions of this bulletin.

vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.

THE APPLIED VEHICLES SECTION HAS BEEN REVISED, A PHOTO HAS BEEN ADDED TO PAGE 4, AND ICC/DISTANCE SENSOR LOCATION INFORMATION FOR MAXIMA AND ROGUE HAS BEEN ADJUSTED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."

Service Bulletin to clarify that a change has been made for the logic that controls the Occupant Classification System (OCS) and passenger airbag indicator (PABI), as described in the Owners Manual. This TSB applies only to vehicles using the 2-sensor OCS. Those changes are: PABI light is ON with an empty front passenger seat.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and bug fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on page 14. Please discard previous versions of this bulletin.

replacement Audio Unit's registration "code" . - Replace the Audio Unit as instructed in the Electronic Service Manual (ESM) and any applicable bulletins. - Register the replacement Audio Unit with Nissan Owner Services. NOTE: The Apps mode will not function if the Audio Unit serial number (registration code) is not registered. See this bulletin for further detail.

See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin

See AMENDMENT HISTORY on page 9. Please discard previous versions of this bulletin.

The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been superseded to NTB18-031. Please discard all previous versions of this bulletin.

vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.

See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.

This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.

The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section and Table A have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.

breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

Information for 2017 Altima, Murano, Pathfinder, Sentra, and Titan/Titan XD vehicles has been applied. No other changes have been made. Please discard previous versions of this bulletin.

The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.

surface in the area surrounding the license lamp finisher (Figure 1) or replacing the license lamp finisher for any reason. ACTION - Replace the license lamp finisher with the new replacement part listed in the Parts Information. - Refer to the Electronic Service Manual (ESM), section EXT - Exterior for removal and installation information. - Repair any damaged surfaces that were in direct contact with the license lamp finisher.

CUSTOMER REPORTS THIS INCIDENT: - THE VEHICLE HAS BEEN SETTING (NOT RUNNING) IN TEMPERATURES BELOW 14F (-10C) FOR AN EXTENDED PERIOD (SUCH AS OVERNIGHT). THEN - A SIDE DOOR IS OPENED. THEN - THE DOOR IS DIFFICULT TO CLOSE/LATCH, WILL NOT CLOSE/LATCH WITH NORMAL PRESSURE; REQUIRES ADDITIONAL EFFORT TO CLOSE/LATCH, OR THE DOOR MAY ONLY LATCH HALF WAY. THEN - THE DOOR WILL CLOSE/LATCH NORMALLY WHEN THE VEHICLE HAS WARMED UP (VEHICLE LEFT IN THE SUN, MOVED INDOORS, OR DRIVEN FOR SEVERAL MINUTES). NOTE: O THE ABOVE INCIDENT DOES NOT APPLY TO SLIDING SIDE DOORS OR A REAR HATCH (BACK DOOR). O THE ABOVE INCIDENT, IF IT SHOULD OCCUR, COULD BE CONFIRMED OR REPORTED FOR ONE OR MORE SIDE DOORS. ACTION REPLACE THE DOOR LOCK FOR THE AFFECTED DOOR. - DO NOT REPLACE ALL SIDE DOOR LOCKS AUTOMATICALLY. REPLACE ONLY THE DOOR LOCK OF THE DOOR(S) WITH THE INCIDENT AS DESCRIBED UNDER IF YOU CONFIRM. - REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION DLK DOOR & LOCK FOR REPLACEMENT PROCEDURE."

A-PILLAR OR FRONT DOOR AREA THAT HAS THE FOLLOWING CHARACTERISTICS: - MAY BE DESCRIBED AS A HOWLING, A HONK, OR A BURRRRRP TYPE SOUND. - IT IS USUALLY NOT CONSISTENT, BUT INTERMITTENT. - IS MOST PREVALENT DURING CROSS WIND CONDITIONS. - CAN OCCUR AT VARIOUS SPEEDS, BUT USUALLY OCCURS BETWEEN 50 80 MPH. - IF THIS NOISE OCCURS, IT MAY BE HEARD COMING FROM THE LEFT SIDE, THE RIGHT SIDE, OR BOTH SIDES. ACTION REPLACE THE FRONT DOOR WEATHER-STRIP(S): - IF NOISE IS COMING FROM ONE SIDE, REPLACE WEATHER-STRIP ON ONLY ONE SIDE (LEFT OR RIGHT). - IF NOISE IS COMING FROM BOTH SIDES, REPLACE WEATHER STRIP ON BOTH SIDES."

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN."

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.

The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

assembly near the lower shaft assembly connection. ACTION Clean oil drip and residue from the steering column assembly per the SERVICE PROCEDURE on page 2. NOTE: Do NOT replace the Steering Column Assembly for this incident, if it should occur. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Ts 3G network connection, including Nissan Group, have had connectivity services affected. NissanConnect Services are no longer available on the APPLIED VEHICLES listed above.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

No other changes have been made. Please discard previous versions of this bulletin.

device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.

THIS TOOL WAS ACCIDENTALLY SHIPPED TO ALL INFINITI RETAILERS TODAY FROM A SUPPLIER. INFINITI RETAILERS WERE NOT BILLED FOR THIS SHIPMENT AND DO NOT HAVE A NEED FOR THIS TOOL AT THIS TIME. THIS TOOL WILL BE AVAILABLE IN THE FUTURE THROUGH TECHMATE AS J-52258, SO RETAILERS CAN STORE THIS TOOL WITH THEIR OTHER SPECIAL TOOLS IN THE EVENT IT IS REQUIRED IN THE FUTURE.

Please discard previous versions of NTB16-015.

Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90 (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.

The center caps for the wheels of these 2016 Sentras are black in color with chrome emblem. This is the correct combination of wheel and center cap for these vehicles. DO NOT file a Warranty Claim to change the center caps for these vehicles. See this bulletin for further detail.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

Pages 19 and 21 have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

provided for customers who have concerns with their Occupant Classification System (OCS) operation after all campaigns have been completed. Follow the steps in this bulletin to determine if this OCS retrofit procedure is applicable to the vehicle you are working on.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.

This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.