2024 Nissan Rogue TSBs

replacement Certification Label or VIN Plate/Label may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. The VIN Plate/Label (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). The Certification Label (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

replacement Certification Label or VIN Plate/Label may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. The VIN Plate/Label (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). The Certification Label (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

in EVAP system close in Work support. After selecting the "EVAP system close" in Work support, the VENT CONTROL/V in Active test becomes non-functional temporarily. When selecting EVAP system close operation in Work support, wait 10 minutes before starting VENT CONTROL/V Active test or cycle the IGN switch ON/OFF for VENT CONTROL/V Active test to be operational. HINT: This bulletin applies to model years that use CONSULT 4 only.

Control Circuit/Open and P05D9 for PCV Regulator Valve Control Circuit Low stored in the ECM, AND The wiring harness, for wiring harness connector F130, is severed at the Crank Case Ventilation Valve under the Engine Cover. ACTION Follow the SERVICE PROCEDURE starting on page 3 to repair the wiring harness. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

HINT: DTC P0012 for INTAKE VALVE TIMING CONTROL B1 may be stored along with P0196 for EOT SENSOR. ACTION Follow the SERVICE PROCEDURE in this bulletin to diagnose DTC P0196 for EOT SENSOR. Disregard P0012 if stored along with P0196. Do not follow the service information in the ESM when diagnosing P0196. The ESM information will be updated at a later date.

the charge air cooler (Figure 1), please be aware of the following information regarding the charge air cooler coolant refill procedure. IMPORTANT: If the charge air cooler coolant reservoir (Figure 2 on page 2) is not filled properly per details in this bulletin, spark plug and/or engine damage may occur. Figure 1

refer to the updated Electronic Service Manual (ESM) service procedure starting on page 2 of this bulletin to ensure that all air pockets have been completely purged. When refilling the cooling system, use Genuine Nissan BLUE LONG LIFE ANTIFREEZE or its equivalent, mixed with water that is distilled or demineralized. This amended procedure will be added to the ESM in a future update to the following ESM section: ENGINE > ENGINE COOLING SYSTEM > KR15DDT > PERIODIC MAINTENANCE > ENGINE COOLANT > Refilling IMPORTANT: The following information under step 5 on page 3 will be added to the ESM. If not using CONSULT, turn on cabin heater switch. Open the ENGINE COOLANT BYPASS VALVE by using CONSULT WORK SUPPORT function. o Refer to : ENGINE - ENGINE CONTROL SYSTEM - KR15DDT - SYSTEM DESCRIPTION - DIAGNOSIS SYSTEM (ECM) - DIAGNOSIS DESCRIPTION - CONSULT Function) Do not use additives, such as water leak preventive, since they may cause cooling waterway blockages.

only SERVICE INFORMATION When working on the charge air cooler coolant system, refer to the information in this bulletin along with the ESM. The engine coolant system and the sub radiator (charge air cooler) coolant system are two (2) completely separate systems. When refilling the sub radiator (charge air cooler) coolant system after a repair, ensure to use the correct refill procedure. o Refer to the ESM: ENGINE > ENGINE COOLING SYSTEM > KR15DDT > PERIODIC MAINTENANCE > SUB RADIATOR COOLANT Figure 1

only AMENDMENT HISTORY PUBLISHED DATE REFERENCE DESCRIPTION July 10, 2024 NTB24-035 Original bulletin published August 28, 2024 NTB24-035A Bulletin no longer active This bulletin is no longer active. Please discard previous versions of NTB24-035.

bulletin for instruction on how to replace the Driver (LH) Side Engine Insulator Mount for KR15 and PR25 engines. HINT: The ESM will be updated with this procedure at a later date. KR15DDT Driver (LH) Side Engine Insulator Mount Replacement: Pages 2 4 PR25DD Driver (LH) Side Engine Insulator Mount Replacement: Pages 5 7

Label QA Dealer Announcement and Procedure ACTION: FOMs & DOMs are asked to ensure that dealers are aware of this new campaign information. Dealer Announcement: To ensure continued customer satisfaction and confidence, Nissan is conducting a quality action on certain specific model year 2025 ARIYA, 2024-2025 Pathfinder, 2024-2026 Rogue, 2024-2025 Murano and 2025-2026 Kicks vehicles, as identified in Service Comm and DBS National Service History. This action updates the Monroney labels to reflect corrected bumper labeling requirements for California and Hawaii. Dealers will replace original Monroney labels with corrected Monroney labels. Nissan will send VIN-specific corrected labels to address affected vehicles in dealer inventory. New labels will begin shipping via Federal Express Wednesday, October 1, 2025. Dealers will replace original Monroney labels with corrected Monroney labels. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaigns I.D. PD172 & PMA55 New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information Some vehicles may still be in transit. Please continue to check newly arriving inventory for applicability. 2.Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3.Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4.If you have exchanged or traded one of the affected vehicles to another Nissan dealer, please forward the corrected Monroney label to the current dealer upon receipt so it can be attached to the vehicle. If a vehicle has been retailed, dispose of the corrected Monroney label using the same procedure as for destroying the original Monroney label. 5.The service department should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle.

5N1 built on or before October 1, 2021 VINs starting with JN8 built on or before April 7, 2024 IF YOU CONFIRM Water is found to be leaking around the rear window wiper arm pivot seal after performing a water soak test. ACTION Replace the rear window wiper arm pivot seal with the one listed in PARTS INFORMATION on page 3. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Please discard previous versions of NTB26-006.

any drivability concerns or reduced power message in the combination meter, AND DTC P0181 for Fuel Tank Temperature is stored in either Past or Current in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Replace the fuel temperature sensor. 2. Erase all the DTCs.

with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as Active, Past, or Pending in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to determine visually if any leak is present. 4. If the fuel filler lower seal continues to leak, replace the fuel filler tube. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. CONSULT has been updated to allow DTC B2E01-96 for Internal battery to be cleared in the TCU. If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

on a clear day without any rain, snow, or direct sunlight, the Cruise Control/ProPilot stopped working, AND The Automatic Emergency Braking/Forward Emergency Braking light (AEB/FEB) flashed while the Forward Driving Aids Disabled message was displayed in the combination meter, AND DTC C2582-97 for Distance sensor is stored as PAST. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current LASER/RADAR part number. 2. Reprogram the LASER/RADAR, if applicable. 3. Erase the DTCs. 4. Perform Distance Sensor Alignment. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

system OFF warning light" is either ON or flashes and no DTCs are stored, inspect the Lower Front Facia for impact damage and/or the Front Radar bracket for a damage/bent condition. HINT: For the warning light to activate, the vehicle may require a short drive. Refer to Figure 1 on page 3 for an example of a damage/bent condition. o Front Radar brackets that have been damaged by a collision are not covered under warranty. HINT: The AEB system Malfunction See Owners Manual Warning may or may not be displayed in the vehicle information display. For Necessary Repair or Replacement of Affected Components Refer to the ESM: CRUISE CONTROL & DRIVER ASSISTANCE - DRIVER ASSISTANCE SYSTEM - DRIVER ASSISTANCE SYSTEM - REMOVAL AND INSTALLATION - DISTANCE SENSOR Perform Distance Sensor Alignment Refer to ESM: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > ADDITIONAL SERVICE WHEN REPLACING DISTANCE SENSOR

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM The customer experiences an issue with the NissanConnect Service remote commands, AND Any of the following DTCs are displayed as CRNT in the Telematics Control Unit (TCU): B2E4B-06 B2E60-06 B2E61-06 HINT: These DTCs are caused by an issue with a cloud-server that is related to the TCU. ACTION 1. Do NOT replace the TCU. Replacing the TCU will not resolve the concern. 2. Send an email to NTB21-037@Nissan-Usa.com. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.