2019 Nissan Pathfinder TSBs

C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message Unavailable Front Radar Obstruction or Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owners Manual

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly (fuel pump assembly). The fuel level sensor can be replaced separately. P0460 (FUEL LEV SEN SLOSH) P0461 (FUEL LEVEL SENSOR) P0462 (FUEL LEVL SEN/CIRC) P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

OR One or both of the headrest DVD displays are gray (fuzzy) and then change to a solid blue color before displaying the image from the DVD. ACTION Install 2 service jumper harnesses, which connect from each headrest DVD display to the video distributor.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Please discard previous versions of NTB19-029.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

from the rear of the vehicle during the following conditions: When making turns On dry roads At low speeds (under 40 MPH) And The above vibration does not occur if the Electric Controlled Coupling is electrically disconnected. NOTE: In some cases, electrically disconnecting the Electric Controlled Coupling may not eliminate the vibration as described above. In these cases, further confirm the incident by removing the rear propeller shaft and retest. If the vibration does not occur with the rear propeller shaft removed, the incident is confirmed. IMPORTANT: Tire size, brand or tread pattern mismatches can cause similar symptoms. To avoid tire related mismatch vibration, it is recommended that when tires need to be replaced, all tires are replaced at the same time with tires of the proper size, same brand and pattern. See ACTION on page 2.

Activated Liftgate, the back door (liftgate) will not open or close when requested to do so using the: Intelligent Key Back door request switch, located on the back door Automatic back door switch, located on the instrument lower panel LH And DTC B2409 is either current or has been stored in the past. ACTION Replace the automatic back door control module. Refer to the Electronic Service Manual (ESM) section: BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY > DOOR & LOCK > WITH INTELLIGENT KEY SYSTEM > REMOVAL AND INSTALLATION > AUTOMATIC BACK DOOR CONTROL MODULE.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable.

controlled seat: - Heating and cooling features do not operate And - The harness connector or control unit of the climate controlled seat appears as shown in Figure 3 or Figure 5. ACTION Perform the following to the affected seat: A. Replace the climate controlled seat control unit. B. Drill a hole for the new harness clip. C. Replace the harness connector of the climate controlled seat control unit.

reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on page 5. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

VEHICLE does not work after replacing the battery, inspect the positive (+) terminals. If the battery side of the Intelligent Key is held by pinching down on the terminals while removing the battery, it is possible to bend the terminals down far enough that they will not touch the contacts on the other half of the Intelligent Key. If the terminals are found to be bent down, pry them back up so that they will come in contact with the other half of the Intelligent Key?s contacts. - Refer to the photos on the following pages.

flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

See Amendment History on the last page. Please discard previous versions of this bulletin.

above are no longer equipped with a door unlock sensor and/or Body Control Module (BCM) software to provide support for the door unlock sensor. Normal Functionality For Vehicles Built Without Door Unlock Sensor And/Or BCM Software To Support Door Unlock Sensor For Applied Vehicles built after the Applied Dates listed on page 1, using the mechanical key on the driver door will operate differently than vehicles built before the Applied Dates. For these later models, the BCM will not recognize operation of the mechanical key. If a mechanical key is used to lock the driver door: - The security system will not set. If the vehicle is broken into, the alarm will not sound. - Only the driver door will be locked. Other doors will not lock using the mechanical key. If a mechanical key is used to unlock the driver door: - Only the driver door will be unlocked. Other doors will not be unlocked. - If the security system is set, when the door is opened the alarm will sound. NOTE: Using the Unlock button on the Intelligent Key, pushing the request switch on the driver or passenger door with the Intelligent Key in range, or using the Intelligent Key to start the vehicle will silence the alarm. The mechanical key will not operate the power windows.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

associated STOP SALE on 260 MY2019 Pathfinder (R52) vehicles to ensure these vehicles, as delivered to our customers, met our exacting standards and our customers? expectations. Further investigation by Nissan confirmed these subject vehicles can be released for sale without further action. Accordingly, the STOP SALE is rescinded. IMPORTANT: Effective immediately, the STOP SALE is rescinded and the subject vehicles may be released for sale. ***** What Dealers Should Do ***** 1. Effective immediately, dealers may release for sale any vehicles in dealer inventory affected by this quality hold. Thank you for your prompt attention to this matter.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Jack Adapter are now available to allow the CVT to be removed from the APPLIED VEHICLES without having to remove the engine. The procedure in this bulletin is different from the procedure currently in the Electronic Service Manual (ESM), which will be updated with this information at a later date. Please refer to the SERVICE PROCEDURE to use these new tools: Front Wheel Drive (FWD) pages 4 - 26 All Wheel Drive (AWD) pages 27 - 55

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicles 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.

Nissan is conducting a Voluntary Emissions Service Campaign on approximately 104,221 specific Nissan vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or Smog Check test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History Open Campaigns I.D. P9328 Affected Model Year 2015 P9343 Affected Model Year 2016 P9345 Affected Model Year 2017 P9347 Affected Model Year 2018 P9349 Affected Model Year 2019 2. Dealers should remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction.

conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9345, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealers inventory.

conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9435, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealers inventory.

conditions listed below are occurring on an Applied Vehicle with the Intelligent Key within range. - The doors will not lock/unlock when the request switch on an exterior door handle is pressed. - The doors will lock/unlock when the respective buttons are pressed on the Intelligent Key. - The engine will not start when the ignition switch is pressed while depressing the brake. - The engine will start when pressing the Remote Engine Start (RES) button on the Intelligent Key. - The engine will start when pressing the ignition switch while holding the Intelligent Key in front of it. ACTION Replace the BCM. - Refer to the Electronic Service Manual (ESM) for the procedure to replace the BCM: ELECTRICAL & POWER CONTROL > BODY CONTROL SYSTEM > BCM > REMOVAL AND INSTALLATION > BCM (BODY CONTROL MODULE)

Diagnostic Trouble Code (DTC) P0087 (FRP CONTROL SYSTEM) stored in the Engine Control Module (ECM), AND The fuel level indicates or less. ACTION Reprogram the ECM, if applicable.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

used for the Applied Vehicles listed. A single thunk noise may be heard during the first few accelerations of the day from this type of mount, and is considered normal operation. The mount has also been designed with built-in free play that is normal. Under normal driving conditions: - A thunk noise may be heard during the first few accelerations of the day, And - Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: - If it has free play or a ?single event? thunk sound during the first few accelerations of the day. This is considered a normal characteristic of this type of engine mount. - Allowable free play (vertical movement) is 5 mm. - If a shift shock condition is present when shifting from Park into gear or between any combination of gears. This condition is due to transmission line pressure and not movement of the mount. - If a whistle type noise is heard. This is caused by a disconnected vacuum line. NOTE: Refer to the appropriate section of the Electronic Service Manual (ESM) related to transaxles for further diagnostic information on shift shock. Warranty claims for front engine mount replacement due to a whistle noise or a mount that has 5 mm or less free play will be denied.

SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of these DTCs is stored: P17F0 (CVT_JUDDER (T/M INSPECTION)) P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: If a transmission judder (as described above) is not reported, this bulletin does not apply. If either P17F0 or P17F1 are not stored, this bulletin does not apply. If any DTCs are stored other than P17F0 or P17F1, this bulletin does not apply. NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTION Refer to the Repair Flow Chart on page 2 for CVT repair. CAUTION: Always handle the CVT and component assemblies carefully and with the appropriate lifting tools.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

passenger (RH) side drive shaft on an applied vehicle for any reason, transfer assembly drive shaft oil seal and dust cover seal replacement is required. Refer to the SERVICE PROCEDURE in this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

necessary to replace the front floor trim (carpet). The dead pedal is now available as a service part. NOTE: Do not replace the carpet if only the dead pedal is needed. ACTION Follow the SERVICE PROCEDURE on the next page to replace ONLY the Dead pedal. NOTE: Dead pedal is listed in PARTS INFORMATION on the last page.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and bug fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Control Unit (DCU) needs to be replaced on an APPLIED VEHICLE for any reason, follow the steps in the SERVICE PROCEDURE to: - Confirm proper diagnosis and repair with TECH LINE to obtain DCU order approval. - Place the order with DENSO. - Configure the Multi AV system. NOTE: - The original DCU must be installed in the vehicle while performing part of this procedure. DO NOT remove the original DCU until instructed. - The DCU order approval process does not apply to 2017 Pathfinder vehicles. TECH LINE authorization is not needed for 2017 Pathfinder vehicles. For 2017 Pathfinder vehicles, refer to NTB16-104. - This process does not apply to 2017 Armada vehicles since it uses a different system.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This commitment requires Nissan to periodically place certain vehicles on temporary Quality Assurance (QA) Hold to assure that these vehicles, as delivered to our customers, meet our exacting standards and our customers? expectations. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on two hundred sixty (260) specific MY2019 Pathfinder (R52) vehicles that may not meet Nissan design standards. *****What Dealers Should Do***** 1. Verify if vehicles are affected by this quality hold using Service Comm or DBS National Service History ? Open Campaigns I.D. PC693 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). o Refer to NPSB 15-460 for additional information - Some vehicles may still be in transit. Please continue to check newly arriving inventory for QA Hold applicability. 2. Please do not drive, sell, or trade the specific 2019 Pathfinder vehicles in dealer inventory subject to this QA Hold. 3. No further action is necessary at this time. Nissan will provide additional information at a later date.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

equipped with NissanConnect (Intelligent Key). SERVICE INFORMATION An Intelligent Key, for the applied vehicles with NissanConnect, has the abillity to trigger specific customized settings for the radio, clock, heating and air conditioning (HVAC) and navigation that are unique to that key, and each Intelligent Key for a specific vehicle may have different settings stored. EXAMPLE: The vehicle may be driven by more than one person, and each driver has a personal Intelligent Key. Each driver may adjust their preferred vehicle settings differently. If two or more Intelligent Keys with different stored settings are unintentionally interchanged, one or more of the following perceived issues might be reported by the customer(s). - Radio ? Presets are lost or change - Clock ? Settings are not showing the correct time due to day-light savings or the selected region (time zone) - HVAC ? Controls are set differently - Navigation ? Settings suddenly altered If any of these perceived issues are present: - Confirm if there are multiple Intelligent Keys being used by the customer(s) interchangeably, and if so, verify that each key?s settings are different. NOTE: Customer may not recognize that different Intelligent Keys are linked differently.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.