2010 Nissan Maxima TSBs

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.

known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.

attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.

- Customer describes a hesitation at speeds below 15 MPH after the oil was changed. ACTION Replace left and right cylinder bank's "Exhaust Valve Control Magnet Retarder". Please see this bulletin for further details.

Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.

Remove the # 1 main bearing (upper and lower halves), per the Service Procedure in this bulletin. 2. Select and install a new # 1 main bearing that is one grade higher (thicker) than the one removed. See this bulletin for further detail.

vehicle has slower-than-normal acceleration from a stop at times and/or the MIL is ON with DTC P1778 (STEP MOTOR) stored in Engine and/or Transmission. ACTION: Refer to the REPAIR FLOW CHART on Page 2 of this bulletin. See this bulletin for further detail.

- The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.

vehicle is hard to start or cranks and will not start. And * Occurs only on first attempts to start before engine begins running. And * Will not occur after engine has been started and run for any period of time. ACTIONS: * Confirm this bulletin applies and if so reprogram the ECM. See this bulleitn for further details.

Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

voluntary service campaign on specific MY2009-10 Nissan Altima (L32), Altima Coupe (CL32), Altima Hybrid (L32H), and Maxima (A35) vehicles to replace the existing ESCL with an Electronic Steering Column Box (ESCB). The ESCL locks the steering wheel when the vehicle is parked and turned off to help prevent theft. On some vehicles, due to a manufacturing regularity, the ESCL may malfunction after the vehicle is locked and could prevent the engine from starting. This condition, should it occur, will only occur when attempting to start the vehicle, and not while driving. The ESCB will replace the ESCL assembly, but will no longer lock the steering wheel when the vehicle is parked and turned off. The steering wheel locking function is not necessary as the vehicle is also equipped with an anti-theft immobilizer to help prevent theft. Installation of the ESCB will eliminate the possibility of a no-start condition related to the manufacturing irregularity on the ESCL. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm I.D. PC516. 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB17-018 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

conducting a Voluntary Service Campaign to replace the Electronic Steering Column Lock (Steering Lock Unit) on certain specific 2009 ? 2010 model year Maxima and Altima vehicles. This issue does not affect steering or engine operation when the vehicle is already running. This service will be performed at no charge to the customer for parts or labor. NOTE: - After completing this campaign, the steering column will not lock when the ignition is OFF, as it did before. - The new steering lock unit does not have a column lock function. IDENTIFICATION NUMBER Nissan has assigned identification number PC516 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

LIFTED, KNOCKING IS HEARD, OR AT WARM IDLE, NOT HEARD AT HIGHWAY SPEEDS OR SITTING WITH RADIO ON. MODEL 2009-2014 MAXIMA *PE

WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE

TO PREVENT DAMAGE TO VEHICLE ELECTRONIC COMPONENTS FOLLOW THE INSTRUCTIONS/CAUTIONS. NO MODEL YEARS LISTED. *PE

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

(LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.

- Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.

Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.

- When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.

This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

"RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.

The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.

reason: - Do not replace the driver air bag module. The steering wheel switches are now available as a separate service part. - Refer to the Service Procedure in this bulletin for steering wheel switch removal and installation instructions. See this bulletin for more detail.

SENSOR LEAKS, AIR PRESSURE CHANGES WITH ALTITUDE AND AMBIENT TEMPERATURES, AFTERMARKET WHEELS, RADIO FREQUENCY INTERFERENCE CAUSING NO DATA CONDITION AND INFLATING/DEFLATING TIRES WITH TPMS/LTPWS SENSORS. MODEL ALL. NO MODELS YEARS. *PE

MODELS 2009-13 MAXIMA. *PE

INSECTS ARE NEAR OR AROUND RAIN SENSORS. NO MODELS OR MODEL YEARS LISTED. *PE

APPLIES TO ALL 2004 AND LATER (DOES NOT APPLY TO LEAF/EV) VEHICLES. *JS

THE HOSE NOW COMES WITHOUT THE PRESSURE SENSOR. DO NOT DAMAGE PRESSURE SENSOR UPON REMOVAL OR INSTALLATION. IF ONLY THE PRESSURE SENSOR NEEDS TO BE REPLACED, DO NOT REPLACE ANY HOSES. *JS

*MR UPDATED *EH UPDATED 09-12-07. *KB UPDATED 6/21/10. *PE

Repair orders opened after this bulletins published date are no longer eligible for reimbursement under Campaign ID # P0337. Discard all previous versions of NTB10-068.

Repair orders opened after this bulletins published date are no longer eligible for reimbursement under Campaign ID # P1234. Discard all previous versions of NTB11-07

The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.

Control Unit on an Applied Vehicle. Previously, TECH LINE would need to be contacted to confirm (or assist with) diagnosis and the proper repair prior to ordering an A/V control unit. This process has been suspended.

Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.

To remedy this potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system. See this bulletin for further detail. Campaign ID# P1234

To remedy this potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor. See this bulletin for further detail. Campaign ID# P0337

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Discard previous versions of NTB11-103.

IF YOU CONFIRM The Navigation system in an Applied Vehicle reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.

THE TITLE AND IF YOU CONFIRM SECTION HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."

NAVIGATION SOFTWARE UPGRADE. *RM UPDATED 4/1/13. *PE

A SOFTWARE PROBLEM IS CAUSING THE NAVIGATION, IPOD, AND MOBILE PHONE FUNCTIONS TO BE INOPERATIVE. *RM

AFFECTING ALL VEHICLES 2003-11 EXCEPT LEAF, EQUIPPED WITH NAVIGATION SYSTEM. CUSTOMER IS MAILED UPDATE DISC(S) OR SD CARD AND INSTALLS DATA; DEALERSHIP IS MAILED UPDATE DISC(S) AND THE DEALERSHIP INSTALLS DATA WHEN VEHICLE IS BROUGHT IN. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

*JS

*JS

*RM

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.

In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.

The PARTS INFORMATION section has been updated. No other change were made. Please discard previous versions of this bulletin.

right side door mirror assembly needs to be replaced. ACTION Replace ONLY the turn signal. Replacement of the entire door mirror assembly is no longer required.

*KB

OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.

ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.

provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.

other shake or vibrations with the vehicle. ACTION: Use the REPAIR FLOW CHART on page 3 to determine the repair(s) to be performed. NOTES: - The description under IF YOU CONFIRM must exist for this bulletin to apply. - If determined the passenger seatback frame will be replaced: - The headrest, seatback pad, seatback frame bolts, and side airbag nuts must also be replaced. - The seatback trim and seatback board will be reused. - Do not replace the seat cushion and frame assembly or complete seat assembly. See this bulletin for further detail.

Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.

qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

MODEL 2007-2013 NISSAN. *PE

ON CERTAIN VEHICLES, AN UPDATE TO THE NAVIGATION SOFTWARE WILL REMEDY THE NON FUNCTIONALITY OF THE MOBILE PHONE, IPAD AND THE NAVIGATION AT NO CHARGE. *PE UPDATED 4/1/13. *PE

TOWARDS END OF BRINGING VEHICLE TO A STOP (LAST FEW FEET), THE VEHICLE STOPS SLIGHTLY QUICKER THAN EXPECTED. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Hybrid (L32H), and Maxima (A35) vehicles to replace the existing ESCL with an Electronic Steering Column Box (ESCB).

Repair orders opened after May 28, 2020 are no longer eligible for reimbursement under Campaign ID # PC516. Discard previous versions of NTB17-018.

Please discard earlier versions of this bulletin. The original announcement from February 21, 2017 has been revised to include: Service Comm will deactivate PC516 on any unremedied VINs on May 29, 2020. Dealers may continue to schedule and repair vehicles eligible for this service campaign up to and including May 28, 2020. Vehicles presented for repair after May 28, 2020 will not be covered by this service campaign and any repair will be performed at customer expense if no service contract exists. o Either of the following parts may be used for service repairs at customer expense after May 28, 2020: Electronic Steering Column Box (ESCB) 48708-9N00A Electronic Steering Column Lock (ESCL) 48700-9N00B

The original announcement from February 21, 2017 has been revised to include: - Service Comm will deactivate PC516 on any unremedied VINs on May 29, 2020. - Dealers may continue to schedule and repair vehicles eligible for this service campaign up to and including May 29, 2020. - Vehicles presented for repair after May 29, 2020 will not be covered by this service campaign and any repair will be performed at customer expense if no service contract exists.

Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.

We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

MODEL YEARS 2007-2011. MODEL NOT LISTED. *PE

*RM

These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.

See this bulletin for further detail.

All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.

steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.

A XENON HEADLAMP IS NOT FUNCTIONING BECAUSE OF AN ISSUE INSIDE THE HEADLAMP ASSEMBLY (AN INTERNAL ISSUE). IN MOST CASES, REPLACEMENT OF A BULB OR HID CONTROL UNIT WILL SOLVE THE INCIDENT. THIS INCLUDES ALL MODELS WITH XENON HEAD LAMPS. NO MODELS LISTED. *PE

NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB

Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90 (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.

etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.

ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and 2013 LEAF vehicles, see the Service Procedure torque specifications on page 4. See this bulletin for further detail.

leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.

This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.

UPDATED ON 06/08/2011. *KB UPDATED ON 06/13/2011. *RM UPDATED 12/16/2013 *JS

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.