2025 Nissan Kicks TSBs

replacement Certification Label or VIN Plate/Label may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. The VIN Plate/Label (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). The Certification Label (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

replacement Certification Label or VIN Plate/Label may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. The VIN Plate/Label (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). The Certification Label (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

in EVAP system close in Work support. After selecting the "EVAP system close" in Work support, the VENT CONTROL/V in Active test becomes non-functional temporarily. When selecting EVAP system close operation in Work support, wait 10 minutes before starting VENT CONTROL/V Active test or cycle the IGN switch ON/OFF for VENT CONTROL/V Active test to be operational. HINT: This bulletin applies to model years that use CONSULT 4 only.

with Remote Engine Start (RES) requires Engine Control Module (ECM) replacement, the Body Control Module (BCM) must be replaced also at the same time. If you are not familiar with the Re/programming, Configuration procedure, refer to the Electronic Service Manual (ESM) and the CONSULT Operation Manual to reprogram the Electronic Control Unit (ECU). Follow all precautions in both manuals to prevent possible personal injury or death and/or damage to the ECU. This procedure will go back and forth between the ECM and BCM steps as found in the ESM. Damage will occur requiring the ECM and the BCM to be replaced a second time if the following SERVICE PROCEDURE is not followed. Perform the following steps from the Electronic Service Manual (ESM) in this order: A. Perform Work Procedure (Before Replacing ECM) to save the ECM data. B. Remove the ECM. C. Remove the BCM. D. Install the new BCM and then perform Additional Service When Replacing BCM - Work Procedure up to and including Register of Vehicle Identification Number. E. Install the new ECM and then perform Additional Service When Replacing ECM - Work Procedure (After Replacing ECM) up to and including Writing MAC Key for ECM. F. Complete the Additional Service When Replacing BCM - Work Procedure. G. Complete the Additional Service When Replacing ECM - Work Procedure (After Replacing ECM).

This commitment requires Nissan to periodically place certain vehicles on temporary Quality Assurance (QA) Hold to ensure that these vehicles, as delivered to our customers, meet our exacting standards and our customers expectations. Effective immediately, Nissan is placing a temporary Quality Assurance Hold on certain specific 2025 Nissan Kicks & Sentra vehicles while Nissan investigates a potential quality concern with the Engine Cylinder Block. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** 1. Please do not retail the specific vehicles in dealer inventory subject to this quality hold. In order for Nissan customers to have the best experience, please discontinue test drives in the affected vehicles. 2. Nissan is currently investigating a potential quality concern regarding the Engine Cylinder Block. Additional information on next steps will be provided as soon as possible. NISSAN NORTH AMERICA, INC. Total Customer Satisfaction

Label QA Dealer Announcement and Procedure ACTION: FOMs & DOMs are asked to ensure that dealers are aware of this new campaign information. Dealer Announcement: To ensure continued customer satisfaction and confidence, Nissan is conducting a quality action on certain specific model year 2025 ARIYA, 2024-2025 Pathfinder, 2024-2026 Rogue, 2024-2025 Murano and 2025-2026 Kicks vehicles, as identified in Service Comm and DBS National Service History. This action updates the Monroney labels to reflect corrected bumper labeling requirements for California and Hawaii. Dealers will replace original Monroney labels with corrected Monroney labels. Nissan will send VIN-specific corrected labels to address affected vehicles in dealer inventory. New labels will begin shipping via Federal Express Wednesday, October 1, 2025. Dealers will replace original Monroney labels with corrected Monroney labels. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaigns I.D. PD172 & PMA55 New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information Some vehicles may still be in transit. Please continue to check newly arriving inventory for applicability. 2.Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3.Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4.If you have exchanged or traded one of the affected vehicles to another Nissan dealer, please forward the corrected Monroney label to the current dealer upon receipt so it can be attached to the vehicle. If a vehicle has been retailed, dispose of the corrected Monroney label using the same procedure as for destroying the original Monroney label. 5.The service department should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle.

Door Rear Sash Cover is loose or missing. HINT: A loose Rear Door Rear Sash Cover can be lifted at the top/forward corner shown in Figure 1 with one (1) finger and only a few pounds of effort. The driver (LH) side is shown in Figure 1. The passenger (RH) side is similar. ACTION Replace the affected Rear Door Rear Sash Cover with part listed in the PARTS INFORMATION. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

inventory quality action on specific model year 2025 Nissan Kicks vehicles identified in Service Comm and National Service History. On affected vehicles, one or both rear door rear sash covers may be loose. Dealers will inspect and, if necessary, replace one or both rear door rear sash covers. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaigns I.D. PMA44 New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information Some vehicles may still be in transit. Please continue to check newly arriving inventory for applicability. 2. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 3. The parts for this quality action are on restriction and can be ordered via DBS 4. The service department should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle. NISSAN NORTH AMERICA, INC. Total Customer Satisfaction

Door Rear Sash Cover is loose or missing. HINT: A loose Rear Door Rear Sash Cover can be lifted at the top/forward corner shown in Figure 1 with one (1) finger and only a few pounds of effort. The driver (LH) side is shown in Figure 1. The passenger (RH) side is similar. Figure 1 ACTION Replace the affected Rear Door Rear Sash Cover with part listed in the PARTS INFORMATION. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Door Rear Sash Cover is loose or missing. HINT: A loose Rear Door Rear Sash Cover can be lifted at the top/forward corner shown in Figure 1 with one (1) finger and only a few pounds of effort. The driver (LH) side is shown in Figure 1. The passenger (RH) side is similar. Figure 1 ACTION Replace the affected Rear Door Rear Sash Cover with part listed in the PARTS INFORMATION. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Please discard previous versions of NTB26-006.

any drivability concerns or reduced power message in the combination meter, AND DTC P0181 for Fuel Tank Temperature is stored in either Past or Current in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Replace the fuel temperature sensor. 2. Erase all the DTCs.

with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as Active, Past, or Pending in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to determine visually if any leak is present. 4. If the fuel filler lower seal continues to leak, replace the fuel filler tube. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Principal, Sales, Service & Parts Managers *****Dealer Announcement***** To ensure continued customer satisfaction and confidence, Nissan is conducting a quality action on certain specific model year 2025 Nissan Frontier and Kicks vehicles identified in Service Comm. This action updates the Monroney labels to reflect certain safety ratings issued by NHTSA. Dealers will replace original Monroney labels with corrected Monroney labels. Nissan will send VIN-specific corrected labels to address affected vehicles in dealer inventory. New labels will begin shipping via Federal Express Thursday, September 25, 2025. Dealers will replace original Monroney labels with corrected Monroney labels. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer.

B2F70-02 for STOP LAMP is stored in the ECM, check the gap measurement for the lower Brake Pedal Switch with the SERVICE PROCEDURE starting on page 2. If the gap is incorrect, it is recommended to correct the gap measurement, perform Erase All DTCs, and Perform DTC Confirmation Procedure before proceeding with the rest of the ESM diagnostic steps for DTC B2F70-01 and/or B2F70-02. HINT: The lower Brake Pedal Switch is also called Brake Switch 1, Brake Pedal Position Switch, and ASCD Switch in the ESM. The lower switch is manually adjusted, the upper switch is self-adjusting.