2013 Nissan Cube TSBs

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.

ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.

(LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.

- Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.

Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.

- When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.

This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

"RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.

The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.

to use the correct size wheel centering collet (do not use a cone). - Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). - Perform proper wheel mounting and centering checks. See this bulletin for further detail.

reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on page 5. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

SENSOR LEAKS, AIR PRESSURE CHANGES WITH ALTITUDE AND AMBIENT TEMPERATURES, AFTERMARKET WHEELS, RADIO FREQUENCY INTERFERENCE CAUSING NO DATA CONDITION AND INFLATING/DEFLATING TIRES WITH TPMS/LTPWS SENSORS. MODEL ALL. NO MODELS YEARS. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.

known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.

attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.

Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.

- The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.

Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

*JS

*JS

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.

breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.

DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.

of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.

ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.

provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.

Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.

qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

units offered in Nissan vehicles that use this type of map data. * If the wrong SD Map Data Card is used, the NAVI will display an update screen (Figures 1 and 2, reference only) and will only accept Cancel. * If this screen is displayed, install the correct SD Map Data Card, found in table A on page 2, and the NAVI unit will return to correct operation. See this bulletin for further detail.

The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.

SiriusXM Satellite Radio, NavTraffic, NavWeather, Travel Link Weather OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed service is not operating, ... follow the steps in this bulletin to activate/refresh the service.

Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.

See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

(EMMIT) J-51922 is a new special tool that tests the functionality of the following features: Bluetooth o Pairing/Connecting o Phonebook Access Profile o Hands Free Profile (for calls) o Bluetooth Audio test o Message Access Profile (for text messages, if so equipped) USB o Tests USB music playback o Tests USB music browsing capability AUX o Tests AUX Jack playback Use EMMIT to diagnose symptoms related to Bluetooth, USB, and AUX. If EMMIT passes diagnostic tests, the symptom is caused by the customer?s phone and not caused by the AV control unit. DO NOT replace the AV control unit. NOTE: If an AV control unit is replaced for multi-media issues that can be tested with EMMIT, a printed copy of the EMMIT diagnostic results must be included with the returned unit. See page 2 for more information about the EMMIT tool.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN."

MODEL YEARS 2012-2014. NO MODELS LISTED. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Vehicle for any reason (scratch, blemish, etc.): - Do not replace the entire combination meter assemby. The front cover of the combination meter assembly is available as a separate service part. - Refer to the Electronic Service Manual, section MWI-Meter, Warning Lamp & Indicator, for replacement information. See this bulletin for further detail.

No other changes have been made. Please discard previous versions of this bulletin.

Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90 (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.

etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.

See this bulletin for further detail.

All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

the front passenger seat empty. Front passenger air bag status light is ON (illuminated) with an adult sitting in the front passenger seat. Seat belt warning light is ON (illuminated) with the front passenger seat empty (driver seat belt is buckled). Supplemental air bag warning light is flashing but no Air Bag DTCs are stored. ACTION 1. Visually check the front passenger seat and seat rails for any structural damage. 2. Visually check the front passenger seat for any items in the seat pockets, or any items on, under, or hanging from the seat (front, back, and sides). 3. Replace the OCS control unit. 4. Perform Zero Point Rest and check for DTCs. See this bulletin for further detail.

*KB

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and 2013 LEAF vehicles, see the Service Procedure torque specifications on page 4. See this bulletin for further detail.

This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.