1995 Nissan Altima TSBs

*TT

*YC

*YC

*YC

*SD

*TW

*TW

*TW

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE

TO PREVENT DAMAGE TO VEHICLE ELECTRONIC COMPONENTS FOLLOW THE INSTRUCTIONS/CAUTIONS. NO MODEL YEARS LISTED. *PE

*TT

*TT

*TT

CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS ON ALL NISSAN MODELS WITH THE SRS SYSTEMS. *PE UPDATED 2/21/14. *PE

*TT

*TT

REVISED VERSION. *TT

*TT

*TT

*SLC

*TT

*JD

lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

"RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.

*TT

*TT

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.

provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.

qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

*SLC

*TW

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

*JS

*YC

*JD

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

*YC

NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB

*YC

*JD

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

*YC

*TW

*TW

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.