2019 Mitsubishi Outlander TSBs

It covers various topics and reviews the previous months publications.

residue.

capacity be affixed to vehicles when the total net weight of accessories is more than 1.5 percent of the vehicle's gross vehicle weight rating (GVWR) or 100 lbs.

It covers various topics and reviews the previous months publications.

It covers various topics and reviews the previous months publications.

tape when customers complain the Power Seat Side Shield is coming off while entering/exiting the vehicle.

It covers various topics and reviews the previous months publications.

on how to obtain repairs.

It contains Pre-Delivery Inspection (PDI) procedures that dealers must perform when preparing subject vehicles for sale and delivery.

This bulletin informs dealers that it supersedes TSB-17-00-012, issued December, 2017, to add a step to the Pre-Delivery Inspection (PDI) process for California dealers only. The additional step is installation of a Prop 65 Label during the Final Delivery Preparation.

This bulletin contains important new model service information and features for the 2019 Outlander Sport.

dealers.

This bulletin informs dealers that it supersedes TSB-18-00-004, issued July, 2018, to add a step to the Pre-Delivery Inspection (PDI) process for California dealers only. The additional step is installation of a Prop 65 Label during the Final Delivery Preparation.

This bulletin contains important new model service information and features for the 2019 Outlander.

conditioner, ventilation vents) when the blower motor is turned on.

diagnosis, to replace the ignition coils of all cylinders with countermeasure parts when customers report a MIL illumination and a loss of engine power due to the vehicle being in fail safe mode. Unstable idling due to poor contact of the ignition coil terminal and DTC P030X may create this concern.

system for affected vehicles.

complains that the engine will not start while using the remote start system.

vents) when the blower motor is turned on.

replace the ignition coils of all cylinders with countermeasure parts when customers report a MIL illumination and a loss of engine power due to the vehicle being in fail safe mode. Unstable idling due to poor contact of the ignition coil terminal and DTC P030X may create this concern.

replace the ignition coils of all cylinders with countermeasure parts when customers report a MIL illumination and a loss of engine power due to the vehicle being in fail safe mode. Unstable idling due to poor contact of the ignition coil terminal and DTC P030X may create this concern.

affected vehicles with improved countermeasure parts. Due to a change in the reclining motor, the new longer harness and connector are necessary.

affected vehicles with improved countermeasure parts. Due to a change in the reclining motor, the new longer harness and connector are necessary.

of absorbers unnecessarily when trace amounts of oil are noted to have adhered to the shock absorber.

of absorbers unnecessarily when trace amounts of oil are noted to have adhered to the shock absorber.

Exhaust Manifold and instructs dealers to replace the Heat Protector Assembly with a new part.

found at the hose connection and to replace the old hose clamp with a countermeasure clamp and to replace the old water hose with a new water hose.

found at the hose connection and to replace the old hose clamp with a countermeasure clamp and to replace the old water hose with a new water hose.

and MY 2020-2018 Outlander Sports with 2.4L engines.

This bulletin updates the Wheel and Tire section of the Service Manuals to add a Caution to the installation service points of the TPMS valve.

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter. This bulletin supersedes TSB-18-13-003, issued December, 2018, to add Eclipse Cross, applicable Canadian models, and countermeasure dates.

This bulletin updates the Wheel and Tire section of the Service Manuals to add a Caution to the installation service points of the TPMS valve.

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter. This bulletin supersedes TSB-18-13-003, issued December, 2018, to add Eclipse Cross, applicable Canadian models, and countermeasure dates.

This bulletin instructs dealers to how to fix a condition of a metallic knocking sound coming from the rear brakes. Affected vehicles experience this condition when the brake is applied while driving at low speeds, or on driving on uneven roads. Dealers are instructed to replace the rear brake pad clips (upper and lower) with new parts on affected vehicles, and to apply grease between the brake pad and caliper support.

The bulletin instructs dealers to confirm a list of specific Diagnostic Trouble Codes (DTCs) if vehicle experiences the following symptoms in cold weather: the check engine light illuminating with a limited vehicle speed (failsafe mode), or the engine does not restart after driving a short distance and stopping the engine for a few minutes. Once symptoms and DTCs are confirmed, dealers should replace the following relays with anti- freezing types: ETV, A/T (CVT), injector, and starter.

The notice informs dealers that two questionnaire forms have been made available on Mitsubishi Dealer Link (MDL). The questionnaires are to identify how two frequent repairs (loss of Key Fob registration and tire/wheel imbalance) are happening. Mitsubishi Motors North America (MMNA) is requesting dealers to complete the appropriate questionnaire during the customer interview process.

Windshield Wiper in the Exterior portion of the affected Service Manuals.

a natural phenomenon, and water penetration caused by improper sealing or a defective/broken part.

Side Window Switch becomes inoperable during certain conditions when using the one touch function to open/close the window to replace the switch with a new countermeasure part.

Side Window Switch becomes inoperable during certain conditions when using the one touch function to open/close the window to replace the switch with a new countermeasure part.

replacement procedure.

replacement procedure.

windshield Removal and Installation procedure for vehicles equipped with Forward Collision Mitigation System (FCM), Lane Departure Warning System (LDW), and Automatic High Beam System (AHB).

manuals.

TSB-19-42A-002, to add 2020 model year, and provide additional examples of cases where the power window switch may become inoperative.

This bulletin updates the Exterior section of the affected Service Manuals to update door mirror removal and installation details, including non-reusable parts.

This bulletin updates the Body section of the affected Service Manual, to correct the window glass run channel and door opening weather-strip removal and installation procedure.

This bulletin instructs dealers how to repair a vehicle when the power window auto open/close function becomes inoperative after the power window switch is repeatedly operated "ON-OFF" in a short time span.

This bulletin updates the Exterior section of the affected Service Manuals to update door mirror removal and installation details, including non-reusable parts.

This bulletin updates the Body section of the affected Service Manual, to correct the window glass run channel and door opening weather-strip removal and installation procedure.

This bulletin instructs dealers how to repair a vehicle when the power window auto open/close function becomes inoperative after the power window switch is repeatedly operated "ON-OFF" in a short time span.

This bulletin instructs dealers how to re-register vehicle keys for affected vehicles. Affected vehicles may experience a condition of the door(s) inability to be locked or unlocked using the Remote Keyless Entry (RKE) function. Dealers are instructed to re- register the ley using "Customer Key Programming" procedure in the Owner's Manual. This bulletin also provides Summary Table for Function Customization & Key Programming.

The bulletin updates the Body section of the affected Service Manuals to add the type of the hood latch mounting bolt and to correct the tightening torque for the hood.

exhibiting a shudder or surge condition possibly caused by poor reaction of the hydraulic pressure circuit.

exhibiting a shudder or surge condition possibly caused by poor reaction of the hydraulic pressure circuit.

(BSW).

affected vehicles with improved countermeasure parts.

MMNA no longer requires voltage measurements or information about affected vehicles that are beyond the terms of the warranty.

These changes are being made to correct the Left, Right, and Center Reflection Amplitudes within the table.

These changes are being made to correct the Left, Right, and Center Reflection Amplitudes within the table.

should be obtained.

terminals and again at the low beam halogen headlight bulbs for repair validation.

This notice reminds dealers of the importance of using and maintaining electrically insulated gloves servicing affect vehicles. The notice provides dealers with guidelines.

This bulletin updates the Circuit Diagrams section of the affected Service Manuals for the following areas: Taillight, Position Light, Rear Side Marker Light, License Plate Light, Light Monitor/Light Reminder Tone Alarm, Glove Box Light, Floor Console Box Light and Heated Seat.

This bulletin updates the Chassis Electrical section of the affected Service Manuals to update diagnostics for ETACS-ECU CAN timeout diagnostics with DTC U0141.

This bulletin updates the Supplemental Restraint System (SRS) section of the affected Service Manuals to update diagnostics for ETACS-ECU CAN timeout diagnostics with DTC U0141.

This bulletin updates the Body section of the affected Service Manuals to update diagnostics for ETACS-ECU CAN timeout with DTC U0141.

Fail Safe Mode") issued August 2023, to update the Affected Vehicle years and provide VIN cut-off information.

2019-2020 Outlander and 2019-2020 Outlander PHEV built after February 8, 2019.

TSB-17-52A-003, to add Outlander PHEV and additional model years for Outlander and Outlander Sport, and to update parts and procedures to help resolve the power seat movement.

issued January 2019, to update symptoms in the Purpose section, and to remove Outlander PHEV from the Affected Vehicles.

This bulletin instructs dealers to reprogram the BMU (for affected i-MiEV vehicles) or sub-BMU (for affected Outlander PHEV vehicles) with updated software to correct an isolation error when using the ABB quick charger. The isolation error may be detected by the charger, causing the charging process to stop approximately 2 minutes after charging has started. This bulletin supersedes TSB-19-54-001REV, issued March, 2019, to correct the Warranty Coverage in the Warranty Information section.

This bulletin instructs dealers to reprogram the BMU (for affected i-MiEV vehicles) or sub-BMU (for affected Outlander PHEV vehicles) with updated software to correct an isolation error when using the ABB quick charger. The isolation error may be detected by the charger, causing the charging process to stop approximately 2 minutes after charging has started. This bulletin supersedes TSB-19-54-001, issued February, 2019, to add i-MiEV vehicles, and instructions for reprogramming the BMU with updated software.

This bulletin instructs dealers to reprogram the sub-BMU with updated software to correct an isolation error when using the ABB quick charger. The isolation error may be detected by the charger, causing the charging process to stop approximately 2 minutes after charging has started.

This bulletin contains important new model service information and features for the 2019 Outlander PHEV.

belt, related labels, inserts, and replacement of the second row right hand side seat belt (if needed).

belt buckle design on the second row seat.

belt, related labels, inserts, and replacement of the second row right hand side seat belt (if needed). Due to seat arrangement of the second row seat back, if the owner's manual is not properly followed when folding the second row seat back down, the center seat belt buckle may interfere with the right hand side seat belt buckle. As a result, the cover of the right hand side seat belt buckle may come off causing the buckle latch to become inoperable and unable to engage the seat belt tongue.

This Safety Recall Bulletin provides instructions for inspecting the 2nd-row RH-side (passenger side) seat belt shoulder anchor. If necessary, the seat belt will be replaced.

released for the Seat Belt guide being installed improperly. This notice stops sale of the affected vehicles until they are inspected and cleared. The Service Bulletin demonstrates how to repair the defect and complete the recall.

the Seat Belt guide being installed improperly. This notice stops sale of the affected vehicles until they are inspected and cleared.

second row right side seat belt buckle cover has come off, and in some instances, may prevent the second row right side seat belt tongue from latching into the buckle when the internal buckle components have fallen off. This TSB instructs dealers to replace the second row right side seat belt buckle with a new part, which has been shortened by 14 mm to prevent the center seat belt buckle from covering the right side seat belt buckle, and install the countermeasure second row center seat belt buckle.

to install the oil seal within the Automatic Transaxle sections of the applicable Service Manuals.

on-vehicle service for belt & pulley assembly on certain CVT models.

(Service Manual Revision)

F1CJC/W1CJC (CVT-8) transmissions that may exhibit a shudder or surge condition possibly caused by a poor reaction of the hydraulic pressure circuit.

reaction of the hydraulic pressure circuit. With continued driving under these conditions, the CVT belt may slip repeatedly when accelerating, and abrasion powder may enter the hydraulic pressure circuit, causing a warning light to turn on. This TSB instructs dealers to diagnose and test drive vehicles exhibiting this condition. *This TSB may also apply to later model years with F1CJC/W1CJC (CVT-8) transmissions.

technician quiz for 2023.

technician quiz for 2023.

beginning with Model Year 2015.

the Service Brakes portion of the affected Service Manuals.

when customers report a condition where an abnormal rubbing noise is heard from the Seat Back when a driver and/or passenger is seated in the front seat(s).

driver and/or passenger is seated in the front seat(s) and instructs dealers to apply Nonwoven Fabric Tape between the Seat Back and Urethane Pad.

Parking Brake (EPB) function has not been used in a long time and the brake pads are worn down; when the EPB is operated it may take increased amounts of time to function and exceed the threshold value. As a result, the warning light will illuminate and EPB may become inoperative.* *This phenomenon does not effect the normal brakes.

rear end portion of the seat cushion by a passenger, the cushion may sink down and rub against the edges of the metal seat frame. This in turn may cause the damaged urethane material to turn to powder and fall on the floor carpet. This TSB provides a repair procedure to replace the damaged seat cushion pad, and apply tape on the frame to help prevent future damage.

gas springs outside the population of vehicles covered by Safety Recall No. SR-25-002.

Suspension section of the Service Manual.

(Service Manual Revision)

This bulletin instructs dealers to replace both tailgate gas springs with the countermeasure parts when a customer reports a noise generating from the tailgate gas springs when opening and closing the tailgate. This noise may occur when the high sliding friction of the oil seal of the tailgate gas springs cases a stick-slip condition during expansion or contraction.

Required Condition & Pre-Approval Center (PRC) for a vehicle pulling/drifting and/or with steering wheel off-center concerns.

alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns.

a wheel alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns.

photographs when performing a wheel alignment check and adjustment on an affected vehicle with a customer concern of pulling/drifting and/or steering wheel off-center concerns (while under warranty). This Notice supersedes TIN-17-37-001 released in July, 2017, to expand affected models and model years.

poor sound quality during Hands-free phone calls.

Smartphone Link Display Audio built by JVC Kenwood. Voice quality may get worse and become muffled, making it hard for both parties to hear and understand each other. This may be due to an improper parameter setting for echo and noise processing. A software update is now available to address this condition. This TSB instructs dealers how to update the Smartphone Link Display Audio in the affected vehicles listed.

speakers in Mitsubishi vehicles equipped with original equipment audio components.

This bulletin informs dealers that replacement components are now available for 2019 Outlander spare tire installation through Mitsubishi Dealerships. This bulletin also provides details and instructions for the spare tire ordering process.

This bulletin supersedes TSB-18-00-003, issued April, 2018, to add updated information for Carrying Capacity Reduced Label.